M54134FP/GP Earth Leakage Current Detector REJ03F0030-0100Z Rev.1.0 Sep.16.2003 Description The M54134FP/GP is a semiconductor integrated circuit developed for use in high-speed earth leakage breakers incorporating functions to protect against voltage surges and inverter noise. Features • Lightning surge protection Two-count method adopted Improved dead-time performance for lightning impulses • Inverter support For active/low-pass filter use Internal op-amp (low current consumption) Improved high-frequency, high harmonic superposition performance • Internal time delay function A time delay function can be configured • High input sensitivity VT=11.5 mVrms • Low current consumption Standby: 610 µA (typical) Leakage detection: 650 µA (typical) • High-stability design Adopts a circuit with minimal characteristic fluctuation when changes occur in the power supply voltage or ambient temperature Applications • Earth leakage breaker Recommended Operating Conditions • Operating power supply voltage range: 7 to 12 V • Operating ambient temperature: –20 to 85°C Rev.1.0, Sep.16.2003, page 1 of 17 M54134FP/GP Block Diagram VS OPI+ C1 OPI– C2 OPAO ILKI VREF 16 15 14 13 12 11 10 9 – A + M54133FP/GP POWER SUPPLY CIRCUIT SCR DRIVER LEAKAGE DETECTION 1 2 3 4 5 6 7 8 GND IREF VCC OFFC TRC1 TRC2 DLYC SCRT Rev.1.0, Sep.16.2003, page 2 of 17 M54134FP/GP Pin Configuration GND 1 16 VS IREF 2 15 OPI+ OFFC 4 TRC1 5 TRC2 6 DLYC 7 SCRT 8 M54134FP/GP VCC 3 14 C1 13 OPI– 12 C2 11 OPAO 10 ILKI 9 VREF Outline 16P2N-A(FP) Outline 16P2E-A(GP) Pin Description Pin no. Name Function 16 VS Power supply • Common 3 2 1 VCC IREF GND Output pin for internal constant-voltage circuit; connected to decoupling capacitor Pin for connection to resistor to set constant current for internal circuits; approx. 1.3 V Ground • Op-amp 13 15 14 CPI– CPI+ C1 12 11 C2 OPAO Op-amp input pins Pin for connection to capacitors to prevent noise-induced erroneous operation; connected between pins [13], [14] and pins [15], [14] Pin for connection to capacitor to prevent oscillation; connected with pin [11]. Op-amp output pin • Leakage detection, SCR driving circuit 9 10 5 VREF ILKI TRC1 Input reference level pin for leak detection circuit; approx. 2.4 V Another input pin for leak detection circuit Pin to connect a capacitor used to integrate the level discriminator output signal of the leak input signal 6 4 TRC2 OFFC 7 8 DRYC SCRT Pin to connect a capacitor for noise elimination When leak input signal is not continued When a leak is detected and SCR is turned on After a prescribed amount of time, this IC is returned to the initial state. A capacitor to set the time for this function is connected. Pin to connect a capacitor to set the time when using the time delay function Thyristor driving output pin Rev.1.0, Sep.16.2003, page 3 of 17 M54134FP/GP Absolute Maximum Ratings (Unless otherwise noted, Ta = 25°C) Symbol Parameter IS Power supply current Maximum power supply voltage Differential input voltage Differential input current Input current Power consumption Operating ambient temperature Storage temperature IVSmax. Vid IIOP IIG Pd Topr Tstg Rev.1.0, Sep.16.2003, page 4 of 17 Test conditions Across OPI+ and OPI– Across OPI+ and OPI– Across VREF and GND Ratings Unit 4 15 –0.8 to 0.8 –5 to 5 10 200 –20 to 85 –55 to 125 mA V V mA mA mW °C °C M54134FP/GP Electrical Characteristics (Unless otherwise noted, Ta = 25°C) Symbol Quantity Is0 Power supply circuit Is1 Is2 Measurement conditions Ratings Vs Min. Typ. Max. Units 9V 520 610 700 µA Power supply current, during leak detection 560 650 740 µA Power supply current, immediately after SCR driving 480 570 660 µA %/°C Power supply current, during standby — Is0 ambient temp. storage dependence 9V Ta = –20 to 85°C — –0.2 — VSmax. Voltage at max. current — IS = 4 mA — 13.9 15 V VCC VCC pin output voltage 9V IOH = –1 mA — 5.2 — V Voltage amplification 9V f = 1 kHz — 40 — dB –3 dB — 6 — kHz GV BW Opamp Frequency band VO Maximum output voltage — 3.5 — Vpp ISOURCE OPAO pin "H" output current — 2.8 — mA ISINK OPAO pin "L" output current — 0.8 — mA VOF Output offset voltage — 0 — mV IIB Input bias current — 125 — nA V VION IIH VREF VCL EIOH1 VTH1 Iidc = ±4 mA — ±0.8 — vs. VREF — ±14 — mVdc ILK1 pin input bias current VIN = VREF — 220 — nA VREF pin output voltage IOH = –200 µA — 2.4 — V VREF-GND clamping voltage IRCL = 5 mA — 4.7 — V VO = 0; IOH = –7.6 µA –10 — 10 % V Differential input clamping voltage VIB Leakage detection circuit 3 ms circuit Leakage detection DC input voltage TRC1 pin "H" output current precision 9V 9V — 2.4 — ETW1 Tw1 pulse width precision C1 = 0.01 µF; TW1 = 3 ms –15 — 15 % — Tw1 ambient temperature dependence Ta = –20 to 85°C — 0 — %/°C EIOH2 VTH2 1 ms circuit TRC1 pin threshold voltage TRC2 pin "H" output current precision 9V VO = 0; IOH = –7.6 µA TRC2 pin threshold voltage –10 — 10 % — 2.4 — V ETW2 Tw2 pulse width precision C2 = 0.0047 µF; TW2 = 1.5 ms –15 — 15 % — Tw2 ambient temperature dependence Ta = –20 to 85°C — 0 — %/°C 9V VO = 0; IOH = –7.6 µA –10 — 10 % — 2.4 Reset timer pulse width precision 9V C3 = 0.33 µF; TW2 = 75 ms –30 — 30 % DLYC pin "H" output current precision 9V VO = 0; IOH = –7.6 µA –10 — 10 % — 2.4 Time delay timer pulse width precision 9V C4 = 1.0 µF; TW2 = 300 ms –30 — 30 % SCRT pin "L" output voltage 9V IOL = 200 µA — 0.1 0.2 V SCRT pin "H" output current 9V VO = 0.8 V Ta = –20°C –100 –160 — µA Ta = 25°C –50 –130 — µA EIOH3 VTH3 Reset circuit ETW3 EIOH4 VTH4 ETW4 VOL8 IOHc IOHn Time delay circuit SCR driver circuit OFFC pin "H" output current precision OFFC threshold voltage DLYC threshold voltage VT — Overall trip IOH hold power supply voltage — Overall leak detection AC voltage 9V VT ambient temperature dependence Rev.1.0, Sep.16.2003, page 5 of 17 V –30 –100 — µA — 3.0 4.0 V 60 Hz — 11.5 — mVrms Ta = +25 to 80°C — –8.0 — %/°C Ta = +25 to –20°C — +2.0 — Ta = 85°C IOHh Vsoff V M54134FP/GP Timing Charts WITHOUT DELAY FUNCTION ILKI INPUT 2.4V TRC1 PIN Tw1 2.4V TRC2 PIN 2.4V DLYC PIN Tw2 2.4V OFFC PIN 0.7V Tw3 SCRT OUTPUT USING DELAY FUNCTION ILKI INPUT TRC1 PIN 2.4V TRC2 PIN DLYC PIN 2.4V 2.4V Tw4 2.4V OFFC PIN Tw3 SCRT OUTPUT Rev.1.0, Sep.16.2003, page 6 of 17 M54134FP/GP Input/Output Equivalent Circuit 3 VCC VS 16 200 BAND GAP 1.3V 2 IREF EXTERNAL R (180k) 12 C2 VCC 800 2.4V 100 200k OPI- 13 470 11 OPAO VREF 9 OPI+ 15 100 ILKI 10 4.7k C1 14 8 SCRT 6 STAGES 25µA 48k VCC 7.5µA 7.5µA 7.5µA 2.4V 100 5 TCR1 6 TCR2 4 OFFC 7 DLYC Units Resistance : Ω Capacitance : F Rev.1.0, Sep.16.2003, page 7 of 17 M54134FP/GP Precaution for Application Described below are precautions on usage of the M54134FP and the M54134GP. Note that each precaution presents a still better example. It is advisable to review it carefully to learn optimal conditions. 1. Voltage applied to VS (1) Fig.1 shows characteristics of circuit current IS. (IS characterizes clamp circuit shown in INPUT/OUTPUT equivalent circuits.) To design power supply, adapt it to IC, considering IS characteristics. (2) Rectification for use of commercial AC line as power source. RS VS COMMERCIAL AC LINE IC VZ 3 IS (mA) +25°C 2 +85°C -20°C 1 0 ∫∫ 12 13 14 15 VS(V) Fig. 1 CHARACTERISTICS OF VS TO IS a) For VZ, select zener diode of 12V or less. (Prevent supply voltage VS from exceeding absolute maximum rating of 15V.) b) Escalated temperature may decrease supply voltage to produce large current IS. In this case, RS limits IS. (3)For use of common DC power supply, set supply voltage VS within range of 7 to 12V. 2. Resistor (R = 180kΩ) at IREF pin This resistor provides constant-reference-current source for IC. (Constant current source protects IC against fluctuations in supply voltage and ambient temperature.) Since every circuit is characterized by resistance of this resistor, the use of high-precision resistor (accuracy of ±2%) is recommended. 3. Laying out printed-circuit board Foreign noise (from noise simulator, for example) may cause malfunctions. To improve noise resistance, lay out printed-circuit patterns so that wirings of IC to additional capacitors and resistors can be made as short as possible. Carefully design patterns especially for wiring capacitors to VS of [16] pin , VCC of [3] pin , and SCRT of [8] pin. 4. Avoid SCRT output pin voltage from falling negative below GND level. Rev.1.0, Sep.16.2003, page 8 of 17 M54134FP/GP 5. Reset time applicable to reset timer circuit The M54134 has reset timer circuit of VL=0.7V, VH=2.4V, and IO=7.5µA. When SCR is on, power supply path is disconnected from leak detector circuit. As shown in illustration below, disconnection may inhibit VL from falling to 0.7V. Accordingly, reset time may get shortened. To avoid shortage, predetermine a reset time that includes extra time. T= CX(VH-VL) = 0.33µFX(2.4-0.7) =75ms IO 7.5µA 3.8V WAVEFORMS AT OFFC PIN 2.4V 0.7V 75ms WAVEFORMS AT SCRT PIN 0V t=10ms Note. Predetermined reset time may get shortened by t. Rev.1.0, Sep.16.2003, page 9 of 17 M54134FP/GP Typical Characteristics THERMAL DERATING (MAXIMUM RATING) POWER DISSIPATION Pd (mW) 250 200 150 100 50 0 0 25 50 75 100 125 150 AMBIENT TEMPERATURE Ta (°C) 3 SUPPLY CURRENT VS. SUPPLY VOLTAGE CHARACTERISTICS 800 Ta=+25°C SUPPLY CURRENT (µA) SUPPLY CURRENT (mA) SUPPLY CURRENT VS. SUPPLY VOLTAGE CHARACTERISTICS 4 STANDBY +85°C +25°C -20°C 2 1 0 700 LEAK DETECTION STANDBY 600 WHEN SCR IS ON 500 400 0 5 10 6 15 8 10 12 SUPPLY VOLTAGE (V) SUPPLY CURRENT VS. AMBIENT TEMPERATURE CHARACTERISTICS 800 VS=9V VOLTAGE GAIN VS. FREQUENCY CHARACTERISTICS 700 LEAK DETECTION STANDBY 600 WHEN SCR IS ON 500 400 -50 50 VS=9V VOLTAGE GAIN (dB) SUPPLY CURRENT (µA) SUPPLY VOLTAGE (V) 40 30 20 10 0 50 AMBIENT TEMPERATURE (°C) Rev.1.0, Sep.16.2003, page 10 of 17 100 1 10 100 1k 10k FREQUENCY (Hz) 100k 1M INPUT BIAS CURRENT (nA) OPERATIONAL AMPLIFIER INPUT CURRENT BIAS VS. AMBIENT TEMPERATURE CHARACTERISTICS 400 VS=9V 300 200 100 0 -50 0 50 MAXIMUM OUTPUT CURRENT (mA) M54134FP/GP MAXIMUM OPERATIONAL AMPLIFIER OUTPUT CURRENT VS. AMBIENT TEMPERATURE CHARACTERISTICS 4 VS=9V 3 2 1 0 -50 100 AMBIENT TEMPERATURE (°C) 1.3 1.2 1.1 10 1.4 1.3 1.2 1.1 -50 12 SUPPLY VOLTAGE (V) 2.5 2.4 8 10 SUPPLY VOLTAGE (V) Rev.1.0, Sep.16.2003, page 11 of 17 50 100 VREF OUTPUT VOLTAGE VS. AMBIENT TEMPERATURE CHARACTERISTICS 2.7 VS=9V VREF OUTPUT VOLTAGE (V) VREF OUTPUT VOLTAGE (V) 2.6 6 0 AMBIENT TEMPERATURE (°C) VREF OUTPUT VOLTAGE VS. SUPPLY VOLTAGE CHARACTERISTICS 2.7 Ta=+25°C 2.3 100 IREF OUTPUT VOLTAGE VS. AMBIENT TEMPERATURE CHARACTERISTICS 1.5 VS=9V IREF OUTPUT VOLTAGE (V) IREF OUTPUT VOLTAGE (V) 1.4 8 50 AMBIENT TEMPERATURE (°C) IREF OUTPUT VOLTAGE VS. SUPPLY VOLTAGE CHARACTERISTICS 1.5 Ta=+25°C 6 0 12 2.6 2.5 2.4 2.3 -50 0 50 AMBIENT TEMPERATURE (°C) 100 M54134FP/GP 5.5 5.0 4.5 4.0 VCC OUTPUT VOLTAGE VS. AMBIENT TEMPERATURE CHARACTERISTICS 6.0 VS=9V VCC OUTPUT VOLTAGE (V) VCC OUTPUT VOLTAGE (V) VCC OUTPUT VOLTAGE VS. SUPPLY VOLTAGE CHARACTERISTICS 6.0 Ta=+25°C 6 8 10 5.5 5.0 4.5 4.0 -50 12 SUPPLY VOLTAGE (V) 2.5 2.0 8 10 2.0 -50 12 8 7 10 SUPPLY VOLTAGE (V) Rev.1.0, Sep.16.2003, page 12 of 17 50 100 TRC1/TRC2/OFFC/DLYC "H" OUTPUT CURRENT VS. AMBIENT TEMPERATURE CHARACTERISTICS 10 VS=9V "H" OUTPUT CURRENT (µA) "H" OUTPUT CURRENT (µA) 9 8 0 AMBIENT TEMPERATURE (°C) TRC1/TRC2/OFFC/DLYC "H" OUTPUT CURRENT VS. SUPPLY VOLTAGE CHARACTERISTICS 10 Ta=+25°C 6 100 2.5 SUPPLY VOLTAGE (V) 6 50 TRC1/TRC2/OFFC/DLYC THRESHOLD VOLTAGE VS. AMBIENT TEMPERATURE CHARACTERISTICS 3.0 VS=9V THRESHOLD VOLTAGE (V) THRESHOLD VOLTAGE (V) TRC1/TRC2/OFFC/DLYC THRESHOLD VOLTAGE VS. SUPPLY VOLTAGE CHARACTERISTICS 3.0 Ta=+25°C 6 0 AMBIENT TEMPERATURE (°C) 12 9 8 7 6 -50 0 50 AMBIENT TEMPERATURE (°C) 100 M54134FP/GP 3 2 TRC1 PULSE WIDTH VS. AMBIENT TEMPERATURE CHARACTERISTICS 4 VS=9V TRC1=0.01µF TRC1 PULSE WIDTH (ms) TRC1 PULSE WIDTH (ms) TRC1 PULSE WIDTH VS. SUPPLY VOLTAGE CHARACTERISTICS 4 Ta=+25°C TRC1=0.01µF 6 8 10 3 2 -50 12 OFFC "L" OUTPUT VOLTAGE VS. SUPPLY VOLTAGE CHARACTERISTICS 1.2 Ta=+25°C 1.0 0.8 0.6 0.4 6 8 10 0.8 0.6 70 SUPPLY VOLTAGE (V) Rev.1.0, Sep.16.2003, page 13 of 17 12 OFFC PULSE WIDTH (ms) OFFC PULSE WIDTH (ms) 80 10 0 50 100 AMBIENT TEMPERATURE (°C) 90 8 100 1.0 0.4 -50 12 OFFC PULSE WIDTH VS. SUPPLY VOLTAGE CHARACTERISTICS 100 Ta=+25°C OFFC=0.33µF 6 50 OFFC "L" OUTPUT VOLTAGE VS. AMBIENT TEMPERATURE CHARACTERISTICS 1.2 VS=9V SUPPLY VOLTAGE (V) 60 0 AMBIENT TEMPERATURE (°C) OFFC "L" OUTPUT VOLTAGE (V) OFFC "L" OUTPUT VOLTAGE (V) SUPPLY VOLTAGE (V) OFFC PULSE WIDTH VS. AMBIENT TEMPERATURE CHARACTERISTICS 100 VS=9V OFFC=0.33µF 90 80 70 60 -50 0 50 AMBIENT TEMPERATURE (°C) 100 M54134FP/GP TOTAL LEAK DETECTION AC VOLTAGE (mVms) DLYC PULSE WIDTH (ms) 350 300 250 200 DLYC PULSE WIDTH VS. AMBIENT TEMPERATURE CHARACTERISTICS 400 VS=9V DLYC=1.0µF 6 8 10 350 300 250 200 -50 12 0 50 100 SUPPLY VOLTAGE (V) AMBIENT TEMPERATURE (°C) TOTAL LEAK DETECTION AC VOLTAGE VS. SUPPLY VOLTAGE CHARACTERISTICS 13 Ta=+25°C TRC1=0.01µF fin=60Hz 12 TOTAL LEAK DETECTION AC VOLTAGE VS. AMBIENT TEMPERATURE CHARACTERISTICS 13 VS=9V TRC1=0.01µF fin=60Hz 12 11 10 TOTAL LEAK DETECTION AC VOLTAGE (mVms) DLYC PULSE WIDTH (ms) DLYC PULSE WIDTH VS. SUPPLY VOLTAGE CHARACTERISTICS 400 Ta=+25°C DLYC=1.0µF 9 6 8 10 11 10 9 -50 12 SUPPLY VOLTAGE (V) 50 SCRT "L" OUTPUT VOLTAGE (V) SCRT "L" OUTPUT VOLTAGE VS. AMBIENT TEMPERATURE CHARACTERISTICS 0.4 VS=9V IOL=200µA 0.3 0.2 0.1 0 -50 0 50 AMBIENT TEMPERATURE (°C) "L" OUTPUT CURRENT (µA) Rev.1.0, Sep.16.2003, page 14 of 17 100 AMBIENT TEMPERATURE (°C) SCRT "L" OUTPUT VOLTAGE VS. "L" OUTPUT CURRENT CHARACTERISTICS SCRT "L" OUTPUT VOLTAGE (V) 0 100 SCRT "H" OUTPUT CURRENT VS. SUPPLY VOLTAGE CHARACTERISTICS 400 Ta=+25°C 300 200 100 0 0 2 4 6 8 SUPPLY VOLTAGE (V) Rev.1.0, Sep.16.2003, page 15 of 17 10 12 SCRT "H" OUTPUT CURRENT (µA) SCRT "H" OUTPUT CURRENT (µA) M54134FP/GP SCRT "H" OUTPUT CURRENT VS. AMBIENT TEMPERATURE CHARACTERISTICS 400 VS=9V 300 200 100 0 -50 0 50 AMBIENT TEMPERATURE (°C) 100 HE Rev.1.0, Sep.16.2003, page 16 of 17 G Z1 E 1 16 EIAJ Package Code SOP16-P-300-1.27 z Detail G e D JEDEC Code — y b 8 9 x Weight(g) 0.2 M F A Detail F A2 Lead Material Cu Alloy L1 MMP c A1 A A1 A2 b c D E e HE L L1 z Z1 x y Symbol e1 b2 e1 I2 b2 Dimension in Millimeters Min Nom Max 2.1 0 0.1 0.2 — 1.8 — 0.35 0.4 0.5 0.18 0.2 0.25 10.0 10.1 10.2 5.2 5.3 5.4 — 1.27 — 7.5 7.8 8.1 0.4 0.6 0.8 — 1.25 — — 0.605 — — 0.755 — — 0.25 — — 0.1 — 0° 8° — — 0.76 — 7.62 — — 1.27 — Recommended Mount Pad e Plastic 16pin 300mil SOP I2 16P2N-A M54134FP/GP Package Dimensions L Rev.1.0, Sep.16.2003, page 17 of 17 G e Z1 E HE 1 16 z D b 8 9 Detail G y JEDEC Code x M Weight(g) 0.06 Detail F A2 A Lead Material Alloy 42 L1 EIAJ Package Code SSOP16-P-225-0.65 c A1 F L A A1 A2 b c D E e HE L L1 z Z1 x y Symbol e1 b2 e1 I2 b2 Dimension in Millimeters Min Nom Max 1.45 0.2 0.1 0 1.15 0.32 0.22 0.17 0.2 0.15 0.13 5.1 5.0 4.9 4.5 4.4 4.3 0.65 6.6 6.4 6.2 0.7 0.5 0.3 1.0 0.225 0.375 0.13 0.1 0° 10° 0.35 5.8 1.0 Recommended Mount Pad e Plastic 16pin 225mil SSOP I2 16P2E-A M54134FP/GP Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. 3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com). 4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. 5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. 8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein. http://www.renesas.com RENESAS SALES OFFICES Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500 Fax: <1> (408) 382-7501 Renesas Technology Europe Limited. Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, United Kingdom Tel: <44> (1628) 585 100, Fax: <44> (1628) 585 900 Renesas Technology Europe GmbH Dornacher Str. 3, D-85622 Feldkirchen, Germany Tel: <49> (89) 380 70 0, Fax: <49> (89) 929 30 11 Renesas Technology Hong Kong Ltd. 7/F., North Tower, World Finance Centre, Harbour City, Canton Road, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2375-6836 Renesas Technology Taiwan Co., Ltd. FL 10, #99, Fu-Hsing N. Rd., Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999 Renesas Technology (Shanghai) Co., Ltd. 26/F., Ruijin Building, No.205 Maoming Road (S), Shanghai 200020, China Tel: <86> (21) 6472-1001, Fax: <86> (21) 6415-2952 Renesas Technology Singapore Pte. Ltd. 1, Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 © 2003. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon 1.0