75 Ω BNC Style Connector BNC75 Series FEATURE Frequency Range ・ 75 Ω of BNC style connector ・ BNC style connectors can be mated. ・ Bayonet coupling mechanism for reliable connection. Characteristic Impedance 75 Ω Lock Type Bayonet APPLICATIONS Measurement Equipment, Broadcasting, HDTV SPECIFICATIONS Characteristic Impedance Rated Voltage Dielectric Withstanding Voltage 75 Ω 500VAC(r.m.s.) 1500V AC(r.m.s.)for1 minute Contact Resistance 3m Ω Max. Operating Temperature -55 〜 +85℃ Insulation Resistance V.S.W.R. 1000M Ω Mim. at 500V DC 1.3 max. at DC to 1GHz ＊ The specifications are typical but may not apply to all connectors. Please check the specifications on each item with its drawing from us when you use. MATERIAL/FINISH Item Shell (Body) Contact (Male) RoHS Compliant Compliant Material / Finish Copper Alloy / Ni or Ag Plating Copper Alloy / Ag or Au Plating Contact (Female) Copper Alloy / Ag or Au Plating Insulator Gasket PTFE Silicon Rubber ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. 170605 http://www.ddknet.co.jp BNC75 Series Unit：mm ○ Straight Cable Plug L 12.7±0.05 30 φ11.7 30 φ11.7 φ11.7 A 30 +0.1 +0.1 4-φ3.1 0 φ11.5 0 φ15.5 φ15.5 2 33.2 12.7 +0.1 4-φ3.1 0 15.8 26.3 18 12.7 4-φ3.1 17.5 12.7 15.8 +0.1 φ11.5 0 +0.1 2.3 26.3 15.8 4-φ3.0 0 26.3 2.3 Part Number 2.3 12.7 12.7 12.7 39 4-φ3 Finish Outer 12.7 17.5 12.7 +0.1 15.84-φ3.0 0±0.05 12.7 +0.1 26.3 +0.1 4-φ3.0 0 φ9.0 0 +0.1 +0.1 4-φ3.0 0 φ9.0 0 12.7±0.05 +0.1 φ9.0 0 18 33.2 4-φ3.1 12.7±0.05 15.8 BNC75-SP-1.5CCA-EXBV-CF L 18 33.2 5C-FB Center Ag Ag Ni Ag Ni Ag Center 15.8 BNC75-J-2.5C2W-CR10A-CF 26.3 12.7±0.05 Outer Finish 12.7 12.7±0.05 2.5C-2W 17.5 Ni +0.1 12.7±0.05 2 Center Conductor Conductor 4-φ3.0 0 2 18 http://www.ddknet.co.jp Assembly Crimp Tool Instruction CR-H-1101 17.5 2.5C-XW +0.1 0 3 4-φ3.1 Applicable Cable 12.7±0.05 +0.1 φ9.0 0 Assembly Instruction 17.5 12.7 φ9.0 ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. 33.2 Finish 4-φ3.1 Conductor Conductor 12.7 12.7±0.05 4-φ3.1 Ni 1.5CCA-EXBV Au 17.5 2.3 2.3 18 12.7 37 5C-2V17.5 Applicable Cable ±0.05 32.5 2 32.5 φ15.5 +0.1 φ11.5 0 Part Number φ14.5 φ4.0 φ15.5 φ11.7 φ11.7 φ15.5 2 Outer Conductor Conductor 12.7 +0.1 12.7±0.05 φ11.5 0 32.5 ○ Straight Cable Jack 33.2 φA +0.1 BNC75-SP-5CFB-CF 32.5 2 L 4-φ3 17.5 4-φ3.1 0 2.3 15.8 BNC75-P-5C2W-CF 5C-2W 37 12.7 +0.1 ±0.05 12.7+0.1 0 4-φ3.1 L 0 φ11.5 17.5 2.3 32.5 4-φ3 12.7 12.7 30 4-φ3 17.5 12.7 φ14.5 φ14.5 φ14.5 φ14.5 φ14.5 φ4.0 φ17.5 φ4.0 φ4.0 φ4.0 A 12.7 17.5 Cable +0.1 4-φ3.1 0 15.8 Au 12.7 A 15.8 L Assembly Instruction 4-φ3 12.7 Applicable Part Number L Center Ni +0.1 4-φ3.1 0 2.3 15.8 2.3 +0.1 φA 0 BNC75-P-5-CF 2.3 CR-H-1132 12.7 A 6.5 12.7±0.05 φ17.5 A 1 Outer 12.7 φ14.5 φ14.5 φ14.5 φ14.5 φAφ17.5 φ17.5 φ14.5 φ17.5 29 Au 12.7 12.7 12.7±0.05 14.0 2.3 CR-H-1105 Conductor Conductor 3C-2V 12.7±0.05 +0.1 φA 0 1 12.7 +0.1 12.7±0.05 BNC75-SP-3C2V-CR1-DA1 φA 0 Au Finish φA Cable +0.1 +0.1 4-φ3.1 0 φA 0 φ14.5 26.3 29 17.5 4-φ3.1 Applicable 12.7 Part Number +0.1 L 4-φ3.1 0 12.7±0.05 12.7±0.05 12.7±0.05 ±0.05 12.7 +0.1 CR-H-1100 17.5 12.7 +0.1 14.00 4-φ3.1 φA 0 Ni Assembly Crimp Tool Insutruction Au 12.7 L 17.5 12.7 12.7±0.05 φ14.5 φ14.5 φ14.5 φ14.5 φA φA φA φA 29 30 7.90 +0.1 2.3 Ni 17.5 12.7 L 2.3 14.0 0 4-φ3.1 3C-2WS 29 29 6.25 12.7 14.0 3C-2W BNC75-P-3CW-CR10B-CF Ni 4-φ3.1 2.5C-XW 2.3 14.0 BNC75-P-2.5CW-CR10B-CF 2.5C-2W 26.3 φA 1.5C-QEW 12.7±0.05 12.7±0.05 12.7±0.05 12.7±0.05 26.3 4-φ3.1 5.50 12.7±0.05 φ14.5 φA 26.3 Center 4-φ3.1 Conductor Conductor 1.5C-2W L 2.3 Outer 12.7±0.05 12.7±0.05 12.7±0.05 12.7±0.05 φ14.5 φ14.5 φ14.5 φA φA φA 26.3 φA Cable BNC75-P-1.5CQEW-CF Finish 4-φ3.1 Applicable Part Number Au Assembly Instruction Crimp Tool CR-H-1105 30 φ11.7 12.7 4-φ3.1 BNC75 Series ○ Straight Bulkhead Cable Jack 32.5 2.3 15.8 12.7 26.3 17.5 +0.1 4-φ3.0 0 φ15.5 Cable +0.1 φ9.0 0 2.5C-2W BNC75-BJ-2.5C2W-CR1-CF 2 Outer Finish Center Conductor Conductor Ni ±0.05 12.7 2.5C-QEW 18 33.2 12.7±0.05 Applicable Part Number Assembly Crimp Tool Instruction Au ○ Straight Panel Cable Jack Cable φ11.7 12.7 1.5C-2V 1.5C-QEV Conductor Conductor CR-H-1101 33.00 4-φ3.1 Ni Au CR-H-1101 34.5 Ni Ag CR-H-1100 17.5 +0.1 +0.1 15.8φ11.5 0 12.7 17.5 +0.1 4-φ3.1 0 4-φ3 12.7±0.05 17.5 12.7±0.05 12.7 12.7 +0.1 φ11.5 0 12.7 4-φ3.1 12.7±0.05 2.3 15.8 12.7 4-φ3.1 Panel Mounting Dimensions 26.3 +0.1 0 4-φ3.1 12.7±0.05 32.5 17.5 2.3 15.8 26.3 2 18 12.7 12.7±0.05 12.7±0.05 12.7 4-φ3.1 17.5 2.3 3 15.8 26.3 +0.1 φ9.0 0 12.7 17.5 +0.1 4-φ3.0 0 12.7±0.05 12.7±0.05 32.5 12.7 φ15.5 φ11.7 φ14.5 ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. +0.1 4-φ3.1 4-φ3.0 0 Moreover, the characteristic and the specification of the published product are the reference values. +0.1 Please confirm the content with the latest delivery specifications when you use the product. φ11.5 0 http://www.ddknet.co.jp Assembly Crimp Tool Instruction Au L 17.5 Center Ni4-φ3 2.5C-2V 2.3 CR-H-16776 12.7 15.8 1.5CCA-EXBV 34.5 L +0.1 4-φ3.1 0 15.80 φ11.5 L 30 2.3 Outer 12.7 φ4.0 Cable BNC75-PJ-2.5V-CR-Ni-CF CR-H-1132 4-φ3 Finish L 12.7±0.05 4-φ3 12.7 L +0.1 2.3 Applicable BNC75-PJ-1.5CV-CR2-CF φ14.5 15.8 30 +0.1 Part Number 4 12.7±0.05 Panel Mounting Dimensions 12.7±0.05 φ4.0 2.3 A Au Ni 17.5 Crimp Tool 17.5 +0.1 BNC75-PJ-1.5CCA-EXBV-CF φ14.512.7±0.05 φ17.5 12.7±0.05 φ14.5 φ14.5 +0.1 φA 0 17.5 12.7 12.7 +0.1 0 4-φ3.1 12.7±0.05 A φ14.5 12.7 φ14.5 φ17.5 14.0 Au Assembly Instruction 12.7 φA 0 φ14.5 φ14.5 12.7±0.05 φA φ14.5 +0.1 14.0+0.1 φA 0 4-φ3.1 0 12.7 +0.1 φA 0 L 29 L 17.5 29 4-φ3.1 0 2.3 2.3 Ni 12.7±0.05 φ14.5 φA φ14.5 L 11.3 30.0 +0.1 4-φ3.1 12.7 14.0 14.0 4-φ3.1 L 4-φ3.1 0 12.7 φ14.5 φA φ14.5 2.3 φ14.5 4-φ3.1 26.3 11.8 32.6 2.3 3C-2V Center Conductor Conductor 3C-2WS BNC75-PJ-3C2V-CR1-CF Outer 12.7±0.05 26.3 Finish L 12.7 BNC75-PJ-3CW-CR10B-CF φA 12.7 Applicable Part Number 12.7±0.05 φA φ14.5 4-φ3.1 A Series L ○ Receptacle Jack +0.1 30 17.5 Part Number 2.3 12.7±0.05 15.8 BNC75-R-A-CF 26.3 4-φ3.1 15.8 26.3 2 33.2 17.5 +0.1 +0.1 φ9.0 0 12.7 18 12.7 4-φ3.0 0 12.7 φ15.5 2.3 12.7±0.05 4-φ3.1 12.7±0.05 32.5 Unit：mm 12.7±0.05 12.7±0.05 φ11.5 0 φ11.7 12.7 4-φ3.1 0 +0.1 12.7±0.05 17.5 +0.1 Panel Mounting Dimensions 4-φ3.0 0 12.7±0.05 φ14.5 +0.1 φ11.5 0 +0.1 φ9.0 0 12.7 BNC75 15.8 2.3 φ14.5 φ4.0 φ14.5 12.7 4-φ3.1 12.7±0.05 ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 4 Outer Finish Conductor Ni Center Conductor Au BNC75 Series ○ Assembly Instruction（1） Parts Configulration Heat-shrinkable tubetube Ferule Heat-shrinkable Ferule ① Sleeve Insulator CableCable 15 Contact Sheath Heat-shrinkable tube tube Sheath Heat-shrinkable 15 Sleeve Sleeve Body Body ① Insert the heat-shrinkable tube into the cable 15 OuterOuter Conductor Conductor Body Insulator Insulator Ferule Ferule ② Contact Insulator Insulator Contact and cut the cable as fig.1. Please be carefule to not damage the outer conductor. ② Insert the ferule from the end of outer conductor to the sheath. Spread the top of outer conductor and insert the Outer Conductor sleeve between insulator and outer conductor. Sleeve Sleeve To push the sleeve into the cable, please refer to the tool as fig.2. And cut the outer conductor Inserting Too for Inserting TooSleeve for Sleeve Insulator along the sleeve. 20 min. 20 min. PushPush into sleeve into sleeve on this on side this side 7.2 7.2 3.5 3.5 Sleeve ③ ③ Cut the insulator and center conductor as fig.3. Insulator Insulator Cut the center conductor after pre-soldering. Inserting Too for Sleeve Center Conductor Center Conductor Insulator Insulator （Pre-soldering） （Pre-soldering） 3.5 Insulator Soldering Soldering ④ Center Conductor （Pre-soldering） Insulator Insulator Shave the extra solder from the contact along the Contact Contact round of contact. No gap No gap ring Contact ④ Insert the insulator and solder the center conductor and contact. Pre-solder the contact. ⑤ ⑤ Inser above cable into the body . And insert the contact. gap ⑥ Crimping position is as fig.6. ⑥ Part Number BNC75-P-2.5CW-CR10B-CF BNC75-P-3CW-CR10B-CF Heat-shrinkable tube tube Heat-shrinkable Crimp Tool CR-H-1105 CR-H-1132 ⑦ ⑦ Cover the heat-shrinkable tube on the root of the connector body and heat up the tube. Heat-shrinkable tube ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 5 BNC75 Series Unit：mm ○ Assembly Instruction（2） Parts Configulration Boot Ferule Sleeve Contact Boot Ferule Sleeve Contact Body Body The cable length require for the double-ended cable assembly. L L-12mm L ① Cable 15 Cable 15 ① Insert the boot into the cable and cut the cable Hole the outer as fig.1. Please be carefule to Crimping not damage Boot Sheath Outer Conductor Boot Sheath Outer Conductor conductor. Crimp Tool Crimp Tool Insulator Ferule ② Insulator Ferule Insulator Sleeve Insulator Sleeve Crimping Hole Center Conductor Center Conductor 4.8 3.4 ② Insert the ferule toward outer conductor. 4.8 3.4 Spread the outer conductor and press in the Contact sleeve with stripper (P/N:89134). Contact Pull out the edge Crimp Tool Pull out the edge Crimp Tool Crimped Crimped Stripper （P/N：89134） Stripper （P/N：89134） ③ Center Conductor Center Conductor Cut the insulator and center conductor along this side Cut the insulator and center conductor along this side Body Push crimp tool into outer conductor and insulator ③the Cut the extra Body the root of body. Push the crimpthe tool stripper into from along the surface as fig.3. the root of body. Crimp Position Crimp Position ④ Push the edge of the stripper and rotate. Separate the insulator toward the arrow. ④ Cut the outer conductor along the surface of sleeve. Boot Boot Cut off the outer conductor Cut off the outer conductor ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 6 Ferule ator Contact Sleeve Body BNC75 Series ○ Assembly Instruction（2） 15 ⑤ Crimping Hole Outer Conductor ⑤ Pinch the contact in the crimping hole(center hole) and insert the center conductor of the cable. Crimp the contact (match the side hole of contact Crimp Tool with the curve of crimping hole of tool.) Insulator Ferule 4.8 Sleeve Center Conductor 3.4 Contact Crimp Tool Crimped pper （P/N：89134） ⑥ Center Conductor Push the crimp tool into the root of body. ⑥ Insert the above contact into the body until the top of the contact is same level of the top of insulator. Please do not rotate the body and cable before crimping. Body Crimp the root of the body as fig.6. r Crimp Position ⑦ ⑦ Cover the boot on the body. Boot ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 7 BNC75 Series Unit：mm ○ Assembly Instruction（3） Parts Configulration Nut Washer Gasket Clamp Male Contact Plug Shell 15 Nut ① Washer Gasket Clamp Male Contact Plug Shell ① Cut the cable as fig.1 15 Please be carefule to not damage the outer conductor. ② Insert the nut, washer, gasket and clamp as ② fig.2. The clamp is holded on the sheath and pick the outer conductor. 3 ③ 6 ③ Cut the insulator and center conductor. Turn down the outer conductor to the clamp and cut the outer conductor along the clamp. Cut the 3 insulator and center conductor as fig.3. 6 Please be careful to not damage the center conductor. ④ ④ Solder up the contact to the center conductor. Please be careful to not be swelled up the solder. Please be careful to not gap between contact and insulator. Please be careful to not deform the insulator by soldering. ⑤ Inser the above contact into the body and screw up the nut. ⑤ Please screw up the nut by wrench. ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 8 BNC75 Series ○ Assembly Instruction（4） Parts Configulration Heat-shrinkable tube Ferule Heat-shrinkable tube Sleeve Ferule Insulator Sleeve Insulator Contact Body Contact Body 20 ① 20 Outer Conductor Sheath Heat-shrinkable tube ① Insert the heat-shrinkable tube into the cable and cut the cable as fig.1. Outer Conductor Sheath Heat-shrinkable tube Cut off extra outer conductor ② Cut off extra outer conductor 3.5 A A ② Insert the ferule on the outer conductor. 3.5 Center Conductor Insulator Center Conductor Ferule SleeveInsulator Ferule Sleeve ③ Insulator Insulator Pick the outer conductor and spread the top of center conductor. Insert the insulator from the outer conductor. Cut the extra outer conductor along the sleeve. Cut the insulator in length A. Cut the center conductor after pre-soldering. Part Number Soldering A BNC75-J-2.5C2W-CR10A-CF 7.2mm BNC75-PJ-3CW-CR10B-CF 6.8mm ③ Insert the insulator and solder the contact. Soldering Contact ④ Contact Crimp Tool Crimp Tool ④ Insert the above contact into the body and crimp the body as fig.4. Part Number Same level Same level Body Crimp Tool BNC75-J-2.5C2W-CR10A-CF CR-H-1105 BNC75-PJ-3CW-CR10B-CF CR-H-1132 Body ⑤ ⑤ Cover the heat-shrinkable tube on the root of the connector body and heat up the tube. Heat-shrinkable tube Heat-shrinkable tube ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 9