Series AM10W-NZ 10 Watt | DC-DC Converter Picture coming soon FEATURES: • • • • Super wide 10:1 Input range Extremely High Input range up to 1000VDC Operating temperature of -40 to +70°C Over current and Over Voltage protection • • • • No minimum load required High efficiency of up to 80% I/O Isolation of 4000VAC Reversed connection protection Models Single output Model Input Voltage (V) Output Voltage (V) Output Current max (A) Isolation (VAC) Max Capacitive Load(uF) Efficiency (200VDC) (%) AM10W-60005S-NZ AM10W-60009S-NZ AM10W-60024S-NZ 100-1000 100-1000 100-1000 5 9 24 2 1.11 0.42 4000 4000 4000 6000 4000 470 72 76 80 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Conditions Typical Voltage range Input Current Inrush current <2ms External fuse Startup time 200VDC 600VDC 1000VDC 200VDC 600VDC 1000VDC Slow blow 200-1000VDC Maximum Units 100-1000 75 25 16 VDC 7 20 30 1 mA A 1 A s Maximum Units Isolation Specifications Parameters Tested I/O voltage Conditions Typical 1 min 4000 VAC Output Specifications Parameters Voltage accuracy Line voltage regulation Load voltage regulation Over voltage protection Over current protection Short Circuit protection Short circuit restart Temperature coefficient Ripple & Noise Conditions Typical ±1 ±0.5 ±0.5 Zener diode clamp LL-HL 0-100% load Continuous Auto recovery ±0.02 100 20MHz Bandwidth Maximum Units ±2 ±1 ±1 % % of Vin % 110 % of Iout 200 %/ C mV p-p Maximum Units 75 95 KHz °C °C °C 95 % RH o General Specifications Parameters Switching frequency Operating temperature Storage temperature Maximum case temperature Cooling Humidity Case material www.aimtec.com F 051e R13 Conditions Typical 100% load With derating -40 to 70 -40 to 105 Natural convection Black plastic (UL94-V0) Tel: +1 514 620 2722 1 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM10W-NZ 10 Watt | DC-DC Converter General Specifications (continued) Parameters Conditions Weight Dimensions (L x W x H) MTBF Maximum soldering temperature Typical Maximum 95 2.76 x 1.89 x 0.93 inches 70.00 x 48.00 x 23.50 mm o >300,000 hrs (MIL-HDBK -217F, Ground Benign, t=+25 C) 1.5mm from case for 5-10 sec 260 Units g o C Safety Specifications Parameters EMI - Conducted and radiated emission Electrostatic Discharge Immunity RF, Electromagnetic Field Immunity Electrical Fast Transient/Burst Immunity Surge Immunity RF, Conducted Disturbance Immunity Power frequency Magnetic Field Immunity Voltage dips, Short Interruptions Immunity Standards EN55022, class A (with the recommended EMC circuit) EN55024: 2010 IEC 61000-4-2: Contact ±6KV/Air ±8KV, Criteria B IEC 61000-4-3: 10V/m, Criteria A IEC 61000-4-4: ±4KV, Criteria B IEC 61000-4-5: ±2KV, Criteria B IEC 61000-4-6: 10Vrms, Criteria A IEC 61000-4-8: 10A/m, Criteria A IEC 61000-4-11: 0-70%, Criteria B Pin Out Specifications Pin 1 2 3 4 5 Single N.C. -Vin +Vin -Vout +Vout Dimensions 12.50 (0.49) 4.00 (0.16) 70.00 (2.76) 2 Bottom View 1 5 4 23.00 (0.91) 48.00 (1.89) 20.00 (0.79) 3 2 Top View 5 4 3 1 4.00 (0.16) 62.00 (2.44) 4.00 (0.16) DIV: 10.00 (0.40) 23.50 (0.93) Ø 1.50 (Ø 0.06) www.aimtec.com F 051e R13 6.00 (0.24) 1.00 (0.04) Dimensions mm (inch) Case Tolerance ±0.50 (±0.02) Pin Diameter ± 0.10 (± 0.004) Tel: +1 514 620 2722 2 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM10W-NZ 10 Watt | DC-DC Converter Derating Free Air Convection Free Air Convection 100 Output Power (%) Output Power (%) 100 80 60 Safe Operating Area 100-150VDC 40 20 80 60 Safe Operating Area 150-1000VDC 40 20 0 0 - 40-30 -20 0 20 40 50 70 80 60 100 - 40 -20 0 20 40 50 60 70 80 100 Ambient Temperature º C Ambient Temperature º C Free Air Convection at 25°C Output Power (%) 100 80 70 60 Safe Operating Area 40 20 0 100 200 Input Voltage VDC 1000 NOTE: 1. Derated Pout = Pout * temp. derating * Vin derating. 2. Sufficient air space for natural air flow around must be considered. www.aimtec.com F 051e R13 Tel: +1 514 620 2722 3 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM10W-NZ 10 Watt | DC-DC Converter Typical Application circuit + Vin Single Output FUSE 1A NTC + + Vin MOV S20K1000 DC - Vin + Vout DC - Vin C1 C2 1µF/50V + TVS - Vout - Model C2 TVS 5 Vout 9 Vout 24 Vout 220 µF / 35V 120 µF / 35V 68 µF / 35V 7V 12V 33V Recommended EMC Circuit + Vin FUSE 1A LDM NTC 4.7mH/0.5A LCM 10mH + - Vin 5 Vout 9 Vout 24 Vout + + + MOV S20K1000 Model Single Output C1 R1 C2 R2 C3 R3 C4 R4 + Vout + Vin DC DC - Vin C1, C2, C3 &C4 47 µF/450V + Vout C5 1µF/50V - Vout R1, R2, R3 & R4 C6 TVS 1MΩ / 2W 220 µF / 35V 120 µF / 35V 68 µF / 35V 7V 12V 33V C6 + TVS - Vout NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R13 Tel: +1 514 620 2722 4 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only