EPCOS B72510T0250K062 Ceramic transient voltage suppressor Datasheet

Ceramic transient voltage suppressors
SMD multilayer transient voltage suppressors,
standard series
The following products presented in this data sheet are being withdrawn.
Ordering Code
Substitute Product
Date of
Withdrawal
B72580V0110K062 B72580T0110K062 2012-11-09
B72580V0080L062 B72580T0080L062 2012-11-09
B72580V0060M062 B72580T0040M062 2012-11-09
Deadline Last
Orders
2013-03-01
2013-03-01
2013-03-01
Last Shipments
2013-06-01
2013-06-01
2013-06-01
© EPCOS AG 2012. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
Ordering Code
Substitute Product
Date of
Withdrawal
B72580V0040M062 B72580T0040M062 2012-11-09
B72540V0080L062 B72540T0080L062 2012-11-09
Deadline Last
Orders
2013-03-01
2013-03-01
Last Shipments
2013-06-01
2013-06-01
For further information please contact your nearest EPCOS sales office, which will also support
you in selecting a suitable substitute. The addresses of our worldwide sales network are
presented at www.epcos.com/sales.
Multilayer varistors (MLVs)
Standard series
EPCOS type designation system for standard series
CT
0603
Construction:
CT Single chip with nickel barrier
termination (AgNiSn)
CN Single chip with silver-palladium
termination (AgPd)
CN...K2 Single chip with silver-platinum
termination (AgPt)
Case sizes:
0201
0402
0603
0805
1206
1210
1812
2220
Tolerance of the varistor voltage:
K ±10%
L ±15%
M ±20%
S Special tolerance
Maximum RMS operating voltage (VRMS):
17 17 V
Taping mode:
G 180-mm reel
AgPt termination
Please read Cautions and warnings and
Important notes at the end of this document.
Page 2 of 81
K
17
G
K2
Multilayer varistors (MLVs)
Standard series
Features
ESD acc. to IEC 61000-4-2 level 4
(8 kV contact, 15 kV air discharge)
Surge current up to 1200 A
Bidirectional protection
No derating up to 125°C (for case sizes ≥ 0603)
Fast response (< 0.5 ns)
RoHS-compatible
CT version suitable for lead-free soldering
PSpice simulation models available
Single chip
Applications
ESD protection in mobile phones, cordless phones
and accessories
ESD protection in data bus applications
ESD protection in control electronics, detectors and
sensors, touch screens, plug-in cards, remote
controls
EIA
0201
0402
0603
0805
1206
Metric
0603
1005
1608
2012
3216
1210
3225
Design
Multilayer technology
Lack of plastic or epoxy encapsulation for
flammability rating better than UL 94 V-0
Termination (see “Soldering directions”):
CT types with nickel barrier terminations (AgNiSn),
recommended for lead-free soldering, and
compatible with tin/lead solder.
CN types with silver-palladium terminations
(AgPd) only suitable for reflow and wave soldering
with solder on tin/lead basis.
CN...K2 types with silver-platinum terminations
(AgPt) suitable for reflow lead-free soldering.
1812
4532
2220
5750
V/I characteristics and derating curves
V/I and derating curves are attached to the data sheet.
The curves are sorted by VRMS and then by case size,
which is included in the type designation.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 3 of 81
Internal circuit
Available case sizes:
Multilayer varistors (MLVs)
Standard series
General technical data
Maximum RMS operating voltage
Maximum DC operating voltage
Maximum surge current
Maximum energy absorption
Maximum power dissipation
Maximum clamping voltage
Operating temperature
Storage temperature
Please read Cautions and warnings and
Important notes at the end of this document.
(8/20 µs)
(2 ms)
(8/20 µs)
for case size 0201, 0402
for case size ≥ 0603
for case size 0201, 0402
for case size ≥ 0603
Page 4 of 81
VRMS,max
VDC,max
Isurge,max
Wmax
Pdiss,max
Vclamp,max
Top
Top
LCT/UCT
LCT/UCT
4 ... 60
5.5 ... 85
10 ... 1200
7.5 ... 12000
3 ... 20
17 ... 165
40/+85
55/+125
40/+125
55/+150
V
V
A
mJ
mW
V
°C
°C
°C
°C
Multilayer varistors (MLVs)
Standard series
Temperature derating
Climatic category:
40/+85 °C for case size 0201 and 0402
Climatic category:
55/+125 °C for case size ≥ 0603
Please read Cautions and warnings and
Important notes at the end of this document.
Page 5 of 81
Multilayer varistors (MLVs)
Standard series
Electrical specifications and ordering codes
Maximum ratings (Top,max)
Type
CN standard series
CN1812M4G
CN2220M4G
CN1812M6G
CN2220M6G
CN1812L8G
CN2220L8G
CN1812K11G
CN2220K11G
CN1812K14G
CN1812K14GK2
CN2220K14G
CN1812K17G
CN2220K17G
CN1812K20G
CN2220K20G
CN2220K20GK2
CN1812K25G
CN2220K25G
CN2220K25GK2
CN1812K30G
CN1812K30GK2
CN2220K30G
CN2220K30GK2
CN1812K35GK2
CN2220K35GK2
CN2220K40GK2
CT standard series
CT0201S4AG
CT0402M4G
CT0603M4G
CT0805M4G
CT1206M4G
CT1210M4G
CT0603M6G
V
V
Isurge,max
Wmax
(8/20 µs) (2 ms)
A
mJ
B72580V0040M062
B72540V0040M062
B72580V0060M062
B72540V0060M062
B72580V0080L062
B72540V0080L062
B72580V0110K062
B72540V0110K062
B72580V0140K062
B72582V0140K062
B72540V0140K062
B72580V0170K062
B72540V0170K062
B72580V0200K062
B72540V0200K062
B72542V0200K062
B72580V0250K062
B72540V0250K062
B72542V0250K062
B72580V0300K062
B72582V0300K062
B72540V0300K062
B72542V0300K062
B72582V0350K062
B72542V0350K062
B72542V0400K062
4
4
6
6
8
8
11
11
14
14
14
17
17
20
20
20
25
25
25
30
30
30
30
35
35
40
5.5
5.5
8
8
11
11
14
14
18
18
18
22
22
26
26
26
31
31
31
38
38
38
38
45
45
56
500
1000
500
1200
800
1200
800
1200
800
800
1200
800
1200
800
1200
1200
800
1200
1200
800
800
1200
1200
500
1000
1000
800
1400
1000
3600
1800
4200
1900
5400
2300
2300
5800
2700
7200
3000
7800
7800
3700
9600
9600
4200
4200
12000
12000
4000
7700
9000
15
20
15
20
15
20
15
20
15
15
20
15
20
15
20
20
15
20
20
15
15
20
20
15
20
20
+125
+125
+125
+125
+125
+125
+125
+125
+125
+125
+125
+125
+125
+125
+125
+125
+125
+125
+125
+125
+125
+125
+125
+125
+125
+125
B72440T0040S160
B72590T0040M060
B72500T0040M060
B72510T0040M062
B72520T0040M062
B72530T0040M062
B72500T0060M060
4
4
4
4
4
4
6
5.5
5.5
5.5
5.5
5.5
5.5
8
-
-
-
+85
+85
+125
+125
+125
+125
+125
Ordering code
Please read Cautions and warnings and
Important notes at the end of this document.
VRMS,max VDC,max
Page 6 of 81
20
30
100
150
250
30
7.5
100
100
300
400
100
Pdiss,max Top,max
mW
°C
3
3
5
8
10
3
Multilayer varistors (MLVs)
Standard series
Characteristics (TA = 25 °C)
Type
∆VV
Vclamp,max
%
8
8
11
11
15
15
18
18
22
22
22
27
27
33
33
33
39
39
39
47
47
47
47
56
56
68
15
10
8
8
8
8
11
VV
(1 mA)
V
CN standard series
CN1812M4G
CN2220M4G
CN1812M6G
CN2220M6G
CN1812L8G
CN2220L8G
CN1812K11G
CN2220K11G
CN1812K14G
CN1812K14GK2
CN2220K14G
CN1812K17G
CN2220K17G
CN1812K20G
CN2220K20G
CN2220K20GK2
CN1812K25G
CN2220K25G
CN2220K25GK2
CN1812K30G
CN1812K30GK2
CN2220K30G
CN2220K30GK2
CN1812K35GK2
CN2220K35GK2
CN2220K40GK2
CT standard series
CT0201S4AG
CT0402M4G
CT0603M4G
CT0805M4G
CT1206M4G
CT1210M4G
CT0603M6G
V
Iclamp
(8/20 µs)
A
Ctyp
(1 kHz, 1 V)
pF
±20
±20
±20
±20
±15
±15
±10
±10
±10
±10
±10
±10
±10
±10
±10
±10
±10
±10
±10
±10
±10
±10
±10
±10
±10
±10
17
17
25
25
30
30
33
33
38
38
38
44
44
54
54
54
65
65
65
77
77
77
77
90
90
110
5
10
5
10
5
10
5
10
5
5
10
5
10
5
10
10
5
10
10
5
5
10
10
5
10
10
10000
24000
8000
20000
6000
16000
5000
12000
4500
4500
10000
4000
9000
3000
7000
7000
2500
5000
5000
2000
2000
4000
4000
1200
2500
2000
±20
±20
±20
±20
±20
±20
±20
35
24
19
19
17
17
27
1) Measured @ 1 MHz, 1 V
Please read Cautions and warnings and
Important notes at the end of this document.
Page 7 of 81
1
1
1
1
1
2.5
1
221)
2001)
200
700
1500
5000
200
Multilayer varistors (MLVs)
Standard series
Electrical specifications and ordering codes
Maximum ratings (Top,max)
Type
CT standard series
CT0805M6G
CT1206M6G
CT1210M6G
CT0603K7G
CT0603M7G
CT0603L8G
CT0805L8G
CT1206L8G
CT1210L8G
CT0402S11AG
CT0603K11G
CT0805K11G
CT1206K11G
CT1210K11G
CT0402L14G
CT0402L14UG
CT0603K14G
CT0603S14BG
CT0805K14G
CT1206K14G
CT1210K14G
CT0402S17AG
CT0603K17G
CT0805K17G
CT1206K17G
CT1210K17G
CT0603K20G
CT0805K20G
CT1206K20G
CT1210K20G
CT0603K25G
CT0805K25G
CT1206K25G
CT1210K25G
CT0805K30G
Ordering code
B72510T0060M062
B72520T0060M062
B72530T0060M062
B72500T0070K060
B72500T0070M060
B72500T0080L060
B72510T0080L062
B72520T0080L062
B72530T0080L062
B72590T0110S160
B72500T0110K060
B72510T0110K062
B72520T0110K062
B72530T0110K062
B72590T0140L060
B72590T0140L960
B72500T0140K060
B72500T0140S160
B72510T0140K062
B72520T0140K062
B72530T0140K062
B72590T0170S160
B72500T0170K060
B72510T0170K062
B72520T0170K062
B72530T0170K062
B72500T0200K060
B72510T0200K062
B72520T0200K062
B72530T0200K062
B72500T0250K060
B72510T0250K062
B72520T0250K062
B72530T0250K062
B72510T0300K062
Please read Cautions and warnings and
Important notes at the end of this document.
VRMS,max VDC,max
V
V
6
6
6
7
7
8
8
8
8
11
11
11
11
11
14
14
14
14
14
14
14
17
17
17
17
17
20
20
20
20
25
25
25
25
30
8
8
8
9
9
11
11
11
11
14
14
14
14
14
16
16
18
18
18
18
18
19
22
22
22
22
26
26
26
26
31
31
31
31
38
Page 8 of 81
Isurge,max
Wmax
(8/20 µs) (2 ms)
A
mJ
120
200
300
30
30
30
120
200
400
20
30
120
200
400
20
10
30
30
120
200
400
20
30
120
200
400
30
80
200
400
30
80
200
300
80
200
400
700
100
100
100
200
500
1000
7.5
200
200
500
1200
10
10
200
200
300
500
1500
10
200
300
600
1700
200
300
700
1900
300
300
1000
1700
300
Pdiss,max Top,max
mW
°C
5
8
10
3
3
3
5
8
10
3
3
5
8
10
3
3
3
3
5
8
10
3
3
5
8
10
3
5
8
10
3
5
8
10
5
+125
+125
+125
+125
+125
+125
+125
+125
+125
+85
+125
+125
+125
+125
+85
+85
+125
+125
+125
+125
+125
+85
+125
+125
+125
+125
+125
+125
+125
+125
+125
+125
+125
+125
+125
Multilayer varistors (MLVs)
Standard series
Characteristics (TA = 25 °C)
Type
VV
(1 mA)
V
CT standard series
CT0805M6G
CT1206M6G
CT1210M6G
CT0603K7G
CT0603M7G
CT0603L8G
CT0805L8G
CT1206L8G
CT1210L8G
CT0402S11AG
CT0603K11G
CT0805K11G
CT1206K11G
CT1210K11G
CT0402L14G
CT0402L14UG
CT0603K14G
CT0603S14BG
CT0805K14G
CT1206K14G
CT1210K14G
CT0402S17AG
CT0603K17G
CT0805K17G
CT1206K17G
CT1210K17G
CT0603K20G
CT0805K20G
CT1206K20G
CT1210K20G
CT0603K25G
CT0805K25G
CT1206K25G
CT1210K25G
CT0805K30G
11
11
11
12.5
12.5
15
15
15
15
18.4
18
18
18
18
23.5
23.5
22
22
22
22
22
32
27
27
27
27
33
33
33
33
39
39
39
39
47
∆VV
Vclamp,max
%
V
±20
±20
±20
±10
±20
±15
±15
±15
±15
±10
±10
±10
±10
±10
±15
±15
±10
+23/0
±10
±10
±10
±25
±10
±10
±10
±10
±10
±10
±10
±10
±10
±10
±10
±10
±10
1) Measured @ 1 MHz, 1 V
Please read Cautions and warnings and
Important notes at the end of this document.
Page 9 of 81
27
25
25
27
30
33
33
30
30
35
35
35
33
33
46
46
40
42
40
38
38
59
46
46
44
44
56
56
54
54
67
67
65
65
77
Iclamp
(8/20 µs)
A
1
1
2.5
1
1
1
1
1
2.5
1
1
1
1
2.5
1
1
1
1
1
1
2.5
1
1
1
1
2.5
1
1
1
2.5
1
1
1
2.5
1
Ctyp
(1 kHz, 1 V)
pF
600
1200
4000
130
200
150
500
1000
3000
1201)
100
400
800
2400
471)
471)
100
120
350
700
2000
331)
100
400
650
1800
90
300
600
1500
901)
250
550
1200
200
Multilayer varistors (MLVs)
Standard series
Electrical specifications and ordering codes
Maximum ratings (Top,max)
Type
CT standard series
CT1206K30G
CT1210K30G
CT1206K35G
CT1210K35G
CT1206K40G
CT1210K40G
CT1206K50G
CT1210K50G
CT1206K60G
CT1210K60G
Ordering code
B72520T0300K062
B72530T0300K062
B72520T0350K062
B72530T0350K062
B72520T0400K062
B72530T0400K062
B72520T0500K062
B72530T0500K062
B72520T0600K062
B72530T0600K062
VRMS,max VDC,max
V
V
30
30
35
35
40
40
50
50
60
60
38
38
45
45
56
56
65
65
85
85
Isurge,max
Wmax
(8/20 µs) (2 ms)
A
mJ
200
300
100
250
100
250
100
200
100
200
1100
2000
400
2000
500
2300
600
1600
700
2000
Pdiss,max Top,max
mW
°C
8
10
8
10
8
10
8
10
8
10
+125
+125
+125
+125
+125
+125
+125
+125
+125
+125
Characteristics (TA = 25 °C)
Type
CT standard series
CT1206K30G
CT1210K30G
CT1206K35G
CT1210K35G
CT1206K40G
CT1210K40G
CT1206K50G
CT1210K50G
CT1206K60G
CT1210K60G
VV
(1 mA)
V
∆VV
Vclamp,max
%
V
47
47
56
56
68
68
82
82
100
100
±10
±10
±10
±10
±10
±10
±10
±10
±10
±10
77
77
90
90
110
110
135
135
165
165
Please read Cautions and warnings and
Important notes at the end of this document.
Page 10 of 81
Iclamp
(8/20 µs)
A
1
2.5
1
2.5
1
2.5
1
2.5
1
2.5
Ctyp
(1 kHz, 1 V)
pF
500
1000
200
600
250
500
120
250
100
200
Multilayer varistors (MLVs)
Standard series
Dimensional drawing
Dimensions in mm
Case size
EIA / mm
l
w
h
k
0201 / 0603
0.6 ±0.03
0.30 ±0.03
0.33 max.
0.15 ±0.05
0402 / 1005
1.0 ±0.15
0.50 ±0.10
0.6 max.
0.10 ... 0.30
0603 / 1608
1.6 ±0.15
0.80 ±0.10
0.9 max.
0.10 ... 0.40
0805 / 2012
2.0 ±0.20
1.25 ±0.15
1.4 max.
0.13 ... 0.75
1206 / 3216
3.2 ±0.30
1.60 ±0.20
1.7 max.
0.25 ... 0.75
1210 / 3225
3.2 ±0.30
2.50 ±0.25
1.7 max.
0.25 ... 0.75
1812 / 4532
4.5 ±0.40
3.20 ±0.30
2.5 max.
0.25 ... 1.00
2220 / 5750
5.7 ±0.40
5.00 ±0.40
2.5 max.
0.25 ... 1.00
Recommended solder pad layout
Dimensions in mm
Please read Cautions and warnings and
Important notes at the end of this document.
Case size
EIA / mm
A
B
C
0201 / 0603
0.30
0.25
0.30
0402 / 1005
0.60
0.60
0.50
0603 / 1608
1.00
1.00
1.00
0805 / 2012
1.40
1.20
1.00
1206 / 3216
1.80
1.20
2.10
1210 / 3225
2.80
1.20
2.10
1812 / 4532
3.60
1.50
3.00
2220 / 5750
5.50
1.50
4.20
Page 11 of 81
Multilayer varistors (MLVs)
Standard series
Delivery mode
EIA case size Taping
0201
0402
0402
0402
0402
0402
0603
0603
0603
0603
0603
0603
0603
0603
0603
0603
0603
0805
0805
0805
0805
0805
0805
0805
0805
0805
1206
1206
1206
1206
1206
1206
1206
1206
1206
1206
1206
1206
1206
1210
1210
1210
Cardboard
Cardboard
Cardboard
Cardboard
Cardboard
Cardboard
Cardboard
Cardboard
Cardboard
Cardboard
Cardboard
Cardboard
Cardboard
Cardboard
Cardboard
Cardboard
Cardboard
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Reel size
mm
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
180
Please read Cautions and warnings and
Important notes at the end of this document.
Packing unit
pcs.
15000
10000
10000
10000
10000
10000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
2000
2000
2000
2000
2000
2000
3000
3000
3000
3000
3000
3000
Type
Ordering code
CT0201S4AG
CT0402L14G
CT0402L14UG
CT0402M4G
CT0402S11AG
CT0402S17AG
CT0603K11G
CT0603K14G
CT0603K17G
CT0603K20G
CT0603K25G
CT0603K7G
CT0603L8G
CT0603M4G
CT0603M6G
CT0603M7G
CT0603S14BG
CT0805K11G
CT0805K14G
CT0805K17G
CT0805K20G
CT0805K25G
CT0805K30G
CT0805L8G
CT0805M4G
CT0805M6G
CT1206K11G
CT1206K14G
CT1206K17G
CT1206K20G
CT1206K25G
CT1206K30G
CT1206K35G
CT1206K40G
CT1206K50G
CT1206K60G
CT1206L8G
CT1206M4G
CT1206M6G
CT1210K11G
CT1210K14G
CT1210K17G
B72440T0040S160
B72590T0140L060
B72590T0140L960
B72590T0040M060
B72590T0110S160
B72590T0170S160
B72500T0110K060
B72500T0140K060
B72500T0170K060
B72500T0200K060
B72500T0250K060
B72500T0070K060
B72500T0080L060
B72500T0040M060
B72500T0060M060
B72500T0070M060
B72500T0140S160
B72510T0110K062
B72510T0140K062
B72510T0170K062
B72510T0200K062
B72510T0250K062
B72510T0300K062
B72510T0080L062
B72510T0040M062
B72510T0060M062
B72520T0110K062
B72520T0140K062
B72520T0170K062
B72520T0200K062
B72520T0250K062
B72520T0300K062
B72520T0350K062
B72520T0400K062
B72520T0500K062
B72520T0600K062
B72520T0080L062
B72520T0040M062
B72520T0060M062
B72530T0110K062
B72530T0140K062
B72530T0170K062
Page 12 of 81
Multilayer varistors (MLVs)
Standard series
EIA case size Taping
1210
1210
1210
1210
1210
1210
1210
1210
1210
1210
1812
1812
1812
1812
1812
1812
1812
1812
1812
1812
1812
1812
2220
2220
2220
2220
2220
2220
2220
2220
2220
2220
2220
2220
2220
2220
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Blister
Reel size Packing unit
mm
pcs.
180
3000
180
2000
180
2000
180
2000
180
2000
180
2000
180
2000
180
3000
180
3000
180
3000
180
1500
180
1500
180
1500
180
1500
180
1500
180
1000
180
1000
180
1000
180
1000
180
1500
180
1500
180
1500
180
1500
180
1500
180
1500
180
1500
180
1500
180
1000
180
1000
180
1000
180
1000
180
1000
180
1000
180
1500
180
1500
180
1500
Please read Cautions and warnings and
Important notes at the end of this document.
Type
Ordering code
CT1210K20G
CT1210K25G
CT1210K30G
CT1210K35G
CT1210K40G
CT1210K50G
CT1210K60G
CT1210L8G
CT1210M4G
CT1210M6G
CN1812K11G
CN1812K14G
CN1812K14GK2
CN1812K17G
CN1812K20G
CN1812K25G
CN1812K30G
CN1812K30GK2
CN1812K35GK2
CN1812L8G
CN1812M4G
CN1812M6G
CN2220K11G
CN2220K14G
CN2220K17G
CN2220K20G
CN2220K20GK2
CN2220K25G
CN2220K25GK2
CN2220K30G
CN2220K30GK2
CN2220K35GK2
CN2220K40GK2
CN2220L8G
CN2220M4G
CN2220M6G
B72530T0200K062
B72530T0250K062
B72530T0300K062
B72530T0350K062
B72530T0400K062
B72530T0500K062
B72530T0600K062
B72530T0080L062
B72530T0040M062
B72530T0060M062
B72580V0110K062
B72580V0140K062
B72582V0140K062
B72580V0170K062
B72580V0200K062
B72580V0250K062
B72580V0300K062
B72582V0300K062
B72582V0350K062
B72580V0080L062
B72580V0040M062
B72580V0060M062
B72540V0110K062
B72540V0140K062
B72540V0170K062
B72540V0200K062
B72542V0200K062
B72540V0250K062
B72542V0250K062
B72540V0300K062
B72542V0300K062
B72542V0350K062
B72542V0400K062
B72540V0080L062
B72540V0040M062
B72540V0060M062
Page 13 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT0201S4AG
CT0402M4G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 14 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT0402S11AG
CT0402L14G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 15 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT0402L14UG
CT0402S17AG
Please read Cautions and warnings and
Important notes at the end of this document.
Page 16 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT0603M4G
CT0603M6G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 17 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT0603K7G
CT0603M7G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 18 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT0603L8G
CT0603K11G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 19 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT0603K14G
CT0603S14BG
Please read Cautions and warnings and
Important notes at the end of this document.
Page 20 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT0603K17G
CT0603K20G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 21 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT0603K25G
CT0805M4G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 22 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT0805M6G
CT0805L8G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 23 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT0805K11G
CT0805K14G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 24 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT0805K17G
CT0805K20G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 25 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT0805K25G
CT0805K30G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 26 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT1206M4G
CT1206M6G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 27 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT1206L8G
CT1206K11G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 28 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT1206K14G
CT1206K17G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 29 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT1206K20G
CT1206K25G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 30 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT1206K30G
CT1206K35G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 31 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT1206K40G
CT1206K50G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 32 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT1206K60G
CT1210M4
Please read Cautions and warnings and
Important notes at the end of this document.
Page 33 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT1210M6G
CT1210L8G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 34 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT1210K11G
CT1210K14G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 35 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT1210K17G
CT1210K20G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 36 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT1210K25G
CT1210K30G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 37 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT1210K35G
CT1210K40G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 38 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CT1210K50G
CT1210K60G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 39 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CN1812M4G
CN1812M6G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 40 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CN1812L8G
CN1812K11G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 41 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CN1812K14G(K2)
CN1812K17G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 42 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CN1812K20G
CN1812K25G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 43 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CN1812K30G(K2)
CN2220M4G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 44 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CN1812K35GK2
CN2220M6G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 45 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CN2220L8G
CN2220K11G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 46 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CN2220K14G
CN2220K17G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 47 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CN2220K20G(K2)
CN2220K25G(K2)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 48 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CN2220K30G(K2)
CN2220K35GK2
Please read Cautions and warnings and
Important notes at the end of this document.
Page 49 of 81
Multilayer varistors (MLVs)
Standard series
V/I characteristics
CN2220K40GK2
Please read Cautions and warnings and
Important notes at the end of this document.
Page 50 of 81
Multilayer varistors (MLVs)
Standard series
Derating curves
Maximum surge current Isurge,max = f (tr, pulse train)
For explanation of the derating curves refer to "General technical information", chapter 2.7.2
CT0402M4G ... S17AG
CT0402L14UG
Please read Cautions and warnings and
Important notes at the end of this document.
Page 51 of 81
Multilayer varistors (MLVs)
Standard series
Derating curves
Maximum surge current Isurge,max = f (tr, pulse train)
For explanation of the derating curves refer to "General technical information", chapter 2.7.2
CT0603M4G ... K25G
CT0805M4G
CT1206K35G ... K60G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 52 of 81
Multilayer varistors (MLVs)
Standard series
Derating curves
Maximum surge current Isurge,max = f (tr, pulse train)
For explanation of the derating curves refer to "General technical information", chapter 2.7.2
CT0805M6G ... K17G
CT0805K20G ... K30G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 53 of 81
Multilayer varistors (MLVs)
Standard series
Derating curves
Maximum surge current Isurge,max = f (tr, pulse train)
For explanation of the derating curves refer to "General technical information", chapter 2.7.2
CT1206M4G
CT1206M6G ... K30G
CT1210K50G ... K60G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 54 of 81
Multilayer varistors (MLVs)
Standard series
Derating curves
Maximum surge current Isurge,max = f (tr, pulse train)
For explanation of the derating curves refer to "General technical information", chapter 2.7.2
CT1210M4G
CT1210K35G ... K40G
CT1210M6G
CT1210K25G ... K30G
Please read Cautions and warnings and
Important notes at the end of this document.
Page 55 of 81
Multilayer varistors (MLVs)
Standard series
Derating curves
Maximum surge current Isurge,max = f (tr, pulse train)
For explanation of the derating curves refer to "General technical information", chapter 2.7.2
CT1210L8G ... K20G
CN1812M4G ... M6G
CN1812K35GK2
Please read Cautions and warnings and
Important notes at the end of this document.
Page 56 of 81
Multilayer varistors (MLVs)
Standard series
Derating curves
Maximum surge current Isurge,max = f (tr, pulse train)
For explanation of the derating curves refer to "General technical information", chapter 2.7.2
CN1812L8G ... K30G(K2)
CN2220M4G
CN2220K35GK2, CN2220K40GK2
Please read Cautions and warnings and
Important notes at the end of this document.
Page 57 of 81
Multilayer varistors (MLVs)
Standard series
Derating curves
Maximum surge current Isurge,max = f (tr, pulse train)
For explanation of the derating curves refer to "General technical information", chapter 2.7.2
CN2220M6G ... K30G(K2)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 58 of 81
Multilayer varistors (MLVs)
Standard series
Taping and packing
1
Taping and packing for SMD components
1.1
Blister tape (the taping to IEC 60286-3)
Dimensions in mm
8-mm tape
12-mm tape
16-mm tape
Case size (inch/mm)
Case size
(inch/mm)
Case size
(inch/mm)
0508/
1220
0612/
1632
1012/
2532
Tolerance
0603/
1608
0506/
1216
0805/
2012
1206/
3216
1210/
3225
1812/
4532
2220/
5750
3225 4032
A0
0.9 ±0.10
1.50
1.60
1.90
2.80
3.50
5.10
7.00
B0
1.75 ±0.10
1.80
2.40
3.50
3.50
4.80
6.00
8.70 10.60 ±0.20
K0
1.0
0.80
T
T2
1.80
0.30
1.3
1.20
2.50
8.60 ±0.20
2.60
5.00
max.
0.30
0.30
max.
3.50
5.50
max.
D0
1.50
1.50
1.50
+0.10/0
D1
1.00
1.50
1.50
min.
P0
4.00
4.00
4.00
±0.101)
P2
2.00
2.00
2.00
±0.05
P1
4.00
8.00
12.00
±0.10
W
8.00
12.00
16.00
±0.30
E
1.75
1.75
1.75
±0.10
F
3.50
5.50
7.50
±0.05
G
0.75
0.75
0.75
min.
1) ≤±0.2 mm over 10 sprocket holes.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 59 of 81
Multilayer varistors (MLVs)
Standard series
Part orientation in tape pocket for blister tape
For discrete chip, case sizes 0603, 0805,
1206, 1210, 1812 and 2220
For array, case sizes 0612
For arrays 0506 and 1012
For filter array, case size 0508
Additional taping information
Reel material
Polystyrol (PS)
Tape material
Polystyrol (PS) or Polycarbonat (PC) or PVC
Tape break force
min. 10 N
Top cover tape strength
min. 10 N
Top cover tape peel force
0.2 to 0.6 N for 8-mm tape and 0.2 to 0.8 N for
12-mm tape at a peel speed of 300 mm/min
Tape peel angle
Angle between top cover tape and the direction of feed
during peel off: 165° to 180°
Cavity play
Each part rests in the cavity so that the angle between
the part and cavity center line is no more than 20°
Please read Cautions and warnings and
Important notes at the end of this document.
Page 60 of 81
Multilayer varistors (MLVs)
Standard series
1.2
Cardboard tape (taping to IEC 60286-3)
Dimensions in mm
8-mm tape
Case size
Tolerance
(inch/mm)
Case size (inch/mm)
0201/0603 0402/1005 0405/1012 0603/1608 1003/2508 0508/1220
A0
0.38 ±0.05
0.60
1.05
0.95
1.00
1.60
±0.20
B0
0.68 ±0.05
1.15
1.60
1.80
2.85
2.40
±0.20
T
0.35 ±0.02
0.60
0.75
0.95
1.00
0.95
max.
T2
0.4 min.
0.70
0.90
1.10
1.10
1.12
max.
D0
1.50 ±0.1
1.50
+0.10/0
1.50
P0
4.00
±0.102)
P2
2.00
±0.05
P1
2.00 ±0.05
2.00
4.00
4.00
4.00
4.00
±0.10
W
8.00
±0.30
E
1.75
±0.10
F
G
±0.05
3.50
1.35
0.75
2) ≤0.2 mm over 10 sprocket holes.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 61 of 81
min.
Multilayer varistors (MLVs)
Standard series
Part orientation in tape pocket for cardboard tape
For discrete chip case sizes 0201, 0402, 0603
and 1003
For array case size 0405
For array case size 0508
For filter array, case size 0405
Additional taping information
Reel material
Polystyrol (PS)
Tape material
Cardboard
Tape break force
min. 10 N
Top cover tape strength
min. 10 N
Top cover tape peel force
0.1 to 0.65 N at a peel speed of 300 mm/min
Tape peel angle
Angle between top cover tape and the direction of feed
during peel off: 165° to 180°
Cavity play
Each part rests in the cavity so that the angle between
the part and cavity center line is no more than 20°
Please read Cautions and warnings and
Important notes at the end of this document.
Page 62 of 81
Multilayer varistors (MLVs)
Standard series
1.3
Reel packing
Dimensions in mm
8-mm tape
180-mm reel
330-mm reel
12-mm tape
180-mm reel
330-mm reel
16-mm tape
330-mm reel
A
180 3/+0
330 2.0
180 3/+0
330 2.0
330 2.0
W1
8.4 +1.5/0
8.4 +1.5/0
12.4 +1.5/0
12.4 +1.5/0
16.4 +1.5/0
W2
14.4 max.
14.4 max.
18.4 max.
18.4 max.
22.4 max.
Leader, trailer
Please read Cautions and warnings and
Important notes at the end of this document.
Page 63 of 81
Multilayer varistors (MLVs)
Standard series
1.4
Packing units for discrete chip and array chip
Case size
Chip thickness
inch/mm
0201/0603
0402/1005
0405/1012
0506/1216
0508/1220
0603/1608
0612/1632
0805/2012
th
0.33 mm
0.6 mm
0.7 mm
0.5 mm
0.9 mm
0.9 mm
0.9 mm
0.7 mm
0.9 mm
1.3 mm
0.9 mm
1.0 mm
0.9 mm
1.3 mm
1.4 mm
1.6 mm
0.9 mm
1.3 mm
1.4 mm
1.6 mm
1.3 mm
1.4 mm
1.6 mm
2.3 mm
1.3 mm
1.4 mm
2.0 mm
2.3 mm
3.2 mm
4.5 mm
3.2 mm
4.5 mm
1003/2508
1012/2532
1206/3216
1210/3225
1812/4532
2220/5750
3225
4032
Please read Cautions and warnings and
Important notes at the end of this document.
Cardboard tape Blister tape
W
8 mm
8 mm
8 mm
8 mm
8 mm
8 mm
W
8 mm
8 mm
8 mm
8 mm
8 mm
8 mm
8 mm
8 mm
8 mm
8 mm
8 mm
8 mm
8 mm
8 mm
8 mm
8 mm
12 mm
12 mm
12 mm
12 mm
12 mm
12 mm
12 mm
12 mm
16 mm
16 mm
16 mm
16 mm
Page 64 of 81
∅ 180-mm reel ∅ 330-mm reel
pcs.
15000
10000
5000
4000
4000
4000
3000
3000
3000
3000
4000
2000
3000
3000
2000
2000
3000
3000
2000
2000
1500
1000
1500
1000
pcs.
16000
12000
4000
3000
3000
3000
1000
1000
1000
1000
Multilayer varistors (MLVs)
Standard series
2
Delivery mode for leaded SHCV varistors
Standard delivery mode for SHCV types is bulk. Alternative taping modes (AMMO pack or taped
on reel) are available upon request.
Packing units for:
Type
Pieces
SR6
2000
SR1 / SR2
1000
For types not listed in this data book please contact EPCOS.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 65 of 81
Multilayer varistors (MLVs)
Standard series
Soldering directions
1
Terminations
1.1
Nickel barrier termination
The nickel barrier layer of the silver/nickel/tin termination prevents leaching of the silver base metallization layer. This allows great flexibility in the selection of soldering parameters. The tin prevents the nickel layer from oxidizing and thus ensures better wetting by the solder. The nickel barrier termination is suitable for all commonly-used soldering methods.
Multilayer CTVS: Structure of nickel barrier termination
1.2
Silver-palladium termination
Silver-palladium terminations are used for the large case sizes 1812 and 2220 and for chips intended for conductive adhesion. This metallization improves the resistance of large chips to thermal shock.
In case of conductive adhesion, the silver-palladium metallization reduces susceptibility to corrosion. Silver-palladium termination can be used for smaller case sizes (only chip) for hybrid applications as well. The silver-palladium termination is not approved for lead-free soldering.
Multilayer varistor: Structure of silver-palladium termination
Please read Cautions and warnings and
Important notes at the end of this document.
Page 66 of 81
Multilayer varistors (MLVs)
Standard series
1.3
Silver-platinum termination
Silver-platinum terminations are mainly used for the large case sizes 1812 and 2220. The silverplatinum termination is approved for reflow soldering, SnPb soldering and lead-free soldering with
a silver containing solder paste. In case of SnPb soldering, a solder paste Sn62Pb36Ag2 is recommended. For lead-free reflow soldering, a solder paste SAC, e.g. Sn95.5Ag3.8Cu0.7, is recommended.
Multilayer varistor: Structure of silver-platinum termination
2
Recommended soldering temperature profiles
2.1
Reflow soldering temperature profile
Recommended temperature characteristic for reflow soldering following
JEDEC J-STD-020D
Please read Cautions and warnings and
Important notes at the end of this document.
Page 67 of 81
Multilayer varistors (MLVs)
Standard series
Profile feature
Sn-Pb eutectic assembly
Pb-free assembly
Preheat and soak
- Temperature min
- Temperature max
- Time
Tsmin
Tsmax
tsmin to tsmax
100 °C
150 °C
60 ... 120 s
150 °C
200 °C
60 ... 180 s
Average ramp-up rate
Tsmax to Tp
3 °C/ s max.
3 °C/ s max.
Liquidous temperature
Time at liquidous
TL
tL
183 °C
60 ... 150 s
217 °C
60 ... 150 s
Peak package body temperature
Tp1)
220 °C ... 235 °C2)
245 °C ... 260 °C2)
20 s3)
30 s3)
6 °C/ s max.
6 °C/ s max.
maximum 6 min
maximum 8 min
Time (tP) within 5 °C of specified
classification temperature (Tc)
3)
Average ramp-down rate
Tp to Tsmax
Time 25 °C to peak temperature
1) Tolerance for peak profile temperature (TP) is defined as a supplier minimum and a user maximum.
2) Depending on package thickness. For details please refer to JEDEC J-STD-020D.
3) Tolerance for time at peak profile temperature (tP) is defined as a supplier minimum and a user maximum.
Note: All temperatures refer to topside of the package, measured on the package body surface.
Number of reflow cycles: 3
2.2
Wave soldering temperature profile
Temperature characteristics at component terminal with dual-wave soldering
Please read Cautions and warnings and
Important notes at the end of this document.
Page 68 of 81
Multilayer varistors (MLVs)
Standard series
2.3
Lead-free soldering processes
EPCOS multilayer CTVS with AgNiSn termination are designed for the requirements of lead-free
soldering processes only.
Soldering temperature profiles to JEDEC J-STD-020D, IEC 60068-2-58 and ZVEI recommendations.
3
Recommended soldering methods - type-specific releases by EPCOS
3.1
Overview
Reflow soldering
Wave soldering
Type
Case size
SnPb
Lead-free
SnPb
Lead-free
CT... / CD...
0201/ 0402
Approved
Approved
No
No
CT... / CD...
0603 ... 2220
Approved
Approved
Approved
Approved
CN...
0603 ... 2220
Approved
No
Approved
No
CN...K2
1812, 2220
Approved
Approved
No
No
Arrays
0405 ... 1012
Approved
Approved
No
No
ESD/EMI filters 0405, 0508
Approved
Approved
No
No
CU
3225, 4032
Approved
Approved
Approved
Approved
SHCV
-
No
No
Approved
Approved
3.2
Nickel barrier and AgPt terminated multilayer CTVS
All EPCOS MLVs with nickel barrier and AgPt termination are suitable and fully qualiyfied for leadfree soldering. The nickel barrier layer is 100% matte tin-plated.
3.3
Silver-palladium terminated MLVs
AgPd-terminated MLVs are mainly designed for conductive adhesion technology on hybrid material. Additionally MLVs with AgPd termination are suitable for reflow and wave soldering with SnPb
solder.
Note:
Lead-free soldering is not approved for MLVs with AgPd termination.
3.4
Silver-platinum terminated MLVs
The silver-platinum termination is approved for reflow soldering, SnPb soldering and lead-free
with a silver containing solder paste. In case of SnPb soldering, a solder paste Sn62Pb36Ag2 is
recommended. For lead-free reflow soldering, a solder paste SAC, e.g. Sn95.5Ag3.8Cu0.7, is
recommended.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 69 of 81
Multilayer varistors (MLVs)
Standard series
3.5
Tinned copper alloy
All EPCOS CU types with tinned termination are approved for lead-free and SnPb soldering.
3.6
Tinned iron wire
All EPCOS SHCV types with tinned termination are approved for lead-free and SnPb soldering.
4
Solder joint profiles / solder quantity
4.1
Nickel barrier termination
If the meniscus height is too low, that means the solder quantity is too low, the solder joint may
break, i.e. the component becomes detached from the joint. This problem is sometimes interpreted as leaching of the external terminations.
If the solder meniscus is too high, i.e. the solder quantity is too large, the vise effect may occur.
As the solder cools down, the solder contracts in the direction of the component. If there is too
much solder on the component, it has no leeway to evade the stress and may break, as in a vise.
The figures below show good and poor solder joints for dual-wave and infrared soldering.
4.1.1
Solder joint profiles for nickel barrier termination - dual-wave soldering
Good and poor solder joints caused by amount of solder in dual-wave soldering.
4.1.2
Solder joint profiles for nickel barrier termination / silver-palladium / silver-platinum
termination - reflow soldering
Please read Cautions and warnings and
Important notes at the end of this document.
Page 70 of 81
Multilayer varistors (MLVs)
Standard series
Good and poor solder joints caused by amount of solder in reflow soldering.
5
Conductive adhesion
Attaching surface-mounted devices (SMDs) with electrically conductive adhesives is a commercially attractive method of component connection to supplement or even replace conventional soldering methods.
Electrically conductive adhesives consist of a non-conductive plastic (epoxy resin, polyimide or
silicon) in which electrically conductive metal particles (gold, silver, palladium, nickel, etc) are embedded. Electrical conduction is effected by contact between the metal particles.
Adhesion is particularly suitable for meeting the demands of hybrid technology. The adhesives
can be deposited ready for production requirements by screen printing, stamping or by dispensers. As shown in the following table, conductive adhesion involves two work operations fewer
than soldering.
Reflow soldering
Wave soldering
Conductive adhesion
Screen-print solder paste
Apply glue dot
Screen-print conductive adhesive
Mount SMD
Mount SMD
Mount SMD
Predry solder paste
Cure glue
Cure adhesive
Reflow soldering
Wave soldering
Inspect
Wash
Wash
Inspect
Inspect
Please read Cautions and warnings and
Important notes at the end of this document.
Page 71 of 81
Multilayer varistors (MLVs)
Standard series
A further advantage of adhesion is that the components are subjected to virtually no temperature
shock at all. The curing temperatures of the adhesives are between 120 °C and 180 °C, typical
curing times are between 30 minutes and one hour.
The bending strength of glued chips is, in comparison with that of soldered chips, higher by a factor of at least 2, as is to be expected due to the elasticity of the glued joints.
The lower conductivity of conductive adhesive may lead to higher contact resistance and thus result in electrical data different to those of soldered components. Users must pay special attention
to this in RF applications.
6
Solderability tests
Test
Standard
Wettability
Leaching
resistance
Test conditions
Pb-free soldering
Criteria/ test results
IEC
Immersion in
60068-2-58 60/40 SnPb solder
using non-activated
flux at 215 ± 3 °C
for 3 ± 0.3 s
Immersion in
Sn96.5Ag3.0Cu0.5
solder using non- or
low activated flux
at 245 ± 5 °C
for 3 ± 0.3 s
Covering of 95% of
end termination,
checked by visual
inspection
IEC
Immersion in
60068-2-58 60/40 SnPb
solder using
mildly activated flux
without preheating
at 260 ± 5 °C
for 10 ±1 s
Immersion in
No leaching of
Sn96.5Ag3.0Cu0.5 contacts
solder using non- or
low activated flux
without preheating
at 255 ± 5 °C
for 10 ±1 s
Thermal shock
(solder shock)
Test conditions
Sn-Pb soldering
Dip soldering at
300 °C/5 s
Dip soldering at
300 °C/5 s
No deterioration of
electrical parameters.
Capacitance change:
≤ ±15%
Tests of resistance IEC
Immersion in
Immersion in
to soldering heat
60068-2-58 60/40 SnPb for 10 s Sn96.5Ag3.0Cu0.5
for SMDs
at 260 °C
for 10 s at 260 °C
Change of varistor
voltage:
≤ ±5%
Tests of resistance IEC
to soldering heat
60068-2-20
for radial leaded
components
(SHCV)
Change of varistor
voltage: ≤ ±5%
Change of
capacitance X7R:
≤ 5/+10%
Please read Cautions and warnings and
Important notes at the end of this document.
Immersion
of leads in
60/40 SnPb
for 10 s at 260 °C
Immersion
of leads in
Sn96.5Ag3.0Cu0.5
for 10 s at 260 °C
Page 72 of 81
Multilayer varistors (MLVs)
Standard series
Note:
Leaching of the termination
Effective area at the termination might be lost if the soldering temperature and/or immersion time
are not kept within the recommended conditions. Leaching of the outer electrode should not exceed 25% of the chip end area (full length of the edge A-B-C-D) and 25% of the length A-B,
shown below as mounted on substrate.
As a single chip
7
As mounted on substrate
Notes for proper soldering
7.1
Preheating and cooling
According to JEDEC J-STD-020D. Please refer to chapter 2.
7.2
Repair / rework
Manual soldering with a soldering iron must be avoided, hot-air methods are recommended for
rework purposes.
7.3
Cleaning
All environmentally compatible agents are suitable for cleaning. Select the appropriate cleaning
solution according to the type of flux used. The temperature difference between the components
and cleaning liquid must not be greater than 100 °C. Ultrasonic cleaning should be carried out
with the utmost caution. Too high ultrasonic power can impair the adhesive strength of the metallized surfaces.
7.4
Solder paste printing (reflow soldering)
An excessive application of solder paste results in too high a solder fillet, thus making the chip
more susceptible to mechanical and thermal stress. Too little solder paste reduces the adhesive
strength on the outer electrodes and thus weakens the bonding to the PCB. The solder should be
applied smoothly to the end surface.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 73 of 81
Multilayer varistors (MLVs)
Standard series
7.5
Adhesive application
Thin or insufficient adhesive causes chips to loosen or become disconnected during curing.
Low viscosity of the adhesive causes chips to slip after mounting. It is advised to consult the
manufacturer of the adhesive on proper usage and amounts of adhesive to use.
7.6
Selection of flux
Used flux should have less than or equal to 0.1 wt % of halogenated content, since flux residue
after soldering could lead to corrosion of the termination and/or increased leakage current on the
surface of the component. Strong acidic flux must not be used. The amount of flux applied should
be carefully controlled, since an excess may generate flux gas, which in turn is detrimental to solderability.
7.7
Storage of CTVSs
Solderability is guaranteed for one year from date of delivery for multilayer varistors, CeraDiodes
and ESD/EMI filters (half a year for chips with AgPd and AgPt terminations) and two years for
SHCV and CU components, provided that components are stored in their original packages.
Storage temperature:
25 °C to +45 °C
Relative humidity:
≤75% annual average, ≤95% on 30 days a year
The solderability of the external electrodes may deteriorate if SMDs and leaded components are
stored where they are exposed to high humidity, dust or harmful gas (hydrogen chloride, sulfurous
acid gas or hydrogen sulfide).
Do not store SMDs and leaded components where they are exposed to heat or direct sunlight.
Otherwise the packing material may be deformed or SMDs/ leaded components may stick together, causing problems during mounting.
After opening the factory seals, such as polyvinyl-sealed packages, it is recommended to use the
SMDs or leaded components as soon as possible.
7.8
Placement of components on circuit board
Especially in the case of dual-wave soldering, it is of advantage to place the components on the
board before soldering in that way that their two terminals do not enter the solder bath at different
times.
Ideally, both terminals should be wetted simultaneously.
7.9
Soldering cautions
An excessively long soldering time or high soldering temperature results in leaching of the outer
electrodes, causing poor adhesion and a change of electrical properties of the varistor due to
the loss of contact between electrodes and termination.
Wave soldering must not be applied for MLVs designated for reflow soldering only.
Keep the recommended down-cooling rate.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 74 of 81
Multilayer varistors (MLVs)
Standard series
7.10
Standards
CECC 00802
IEC 60068-2-58
IEC 60068-2-20
JEDEC J-STD-020D
Please read Cautions and warnings and
Important notes at the end of this document.
Page 75 of 81
Multilayer varistors (MLVs)
Standard series
Symbols and terms
Symbol
Term
Cline,typ
Typical capacitance per line
Cmax
Maximum capacitance
Cmin
Minimum capacitance
Cnom
Nominal capacitance
∆Cnom
Tolerance of nominal capacitance
Ctyp
Typical capacitance
fcut-off,min
Minimum cut-off frequency
I
Current
Iclamp
Clamping current
Ileak
Leakage current
Ileak,typ
Typical leakage current
IPP
Peak pulse current
Isurge,max
Maximum surge current (also termed peak current)
LCT
Lower category temperature
Ltyp
Typical inductance
Pdiss,max
Maximum power dissipation
PPP
Peak pulse power
Rins
Insulation resistance
Rmin
Minimum resistance
RS
Resistance per line
TA
Ambient temperature
Top
Operating temperature
Tstg
Storage temperature
tr
Duration of equivalent rectangular wave
tresp
Response time
UCT
Upper category temperature
V
Voltage
VBR,min
Minimum breakdown voltage
Vclamp,max
Maximum clamping voltage
VDC,max
Maximum DC operating voltage (also termed working voltage)
VESD,air
Air discharge ESD capability
VESD,contact
Contact discharge ESD capability
Vjump
Maximum jump start voltage
Please read Cautions and warnings and
Important notes at the end of this document.
Page 76 of 81
Multilayer varistors (MLVs)
Standard series
VRMS,max
Maximum AC operating voltage, root-mean-square value
VV
Varistor voltage (also termed breakdown voltage)
VV,min
Minimum varistor voltage
VV,max
Maximum varistor voltage
∆VV
Tolerance of varistor voltage
WLD
Maximum load dump
Wmax
Maximum energy absorption (also termed transient energy)
αtyp
Typical insertion loss
Lead spacing
*
Maximum possible application conditions
All dimensions are given in mm.
The commas used in numerical values denote decimal points.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 77 of 81
Multilayer varistors (MLVs)
Standard series
Cautions and warnings
General
Some parts of this publication contain statements about the suitability of our ceramic transient
voltage suppressor (CTVS) components (multilayer varistors (MLVs), CeraDiodes, ESD/EMI
filters, SMD disk varistors (CU types), leaded transient voltage/ RFI suppressors (SHCV types))
for certain areas of application, including recommendations about incorporation/design-in of these
products into customer applications. The statements are based on our knowledge of typical
requirements often made of our CTVS devices in the particular areas. We nevertheless expressly
point out that such statements cannot be regarded as binding statements about the suitability of
our CTVS components for a particular customer application. As a rule, EPCOS is either unfamiliar
with individual customer applications or less familiar with them than the customers themselves.
For these reasons, it is always incumbent on the customer to check and decide whether the
CTVS devices with the properties described in the product specification are suitable for use in a
particular customer application.
Do not use EPCOS CTVS components for purposes not identified in our specifications,
application notes and data books.
Ensure the suitability of a CTVS in particular by testing it for reliability during design-in. Always
evaluate a CTVS component under worst-case conditions.
Pay special attention to the reliability of CTVS devices intended for use in safety-critical
applications (e.g. medical equipment, automotive, spacecraft, nuclear power plant).
Design notes
Always connect a CTVS in parallel with the electronic circuit to be protected.
Consider maximum rated power dissipation if a CTVS has insufficient time to cool down
between a number of pulses occurring within a specified isolated time period. Ensure that
electrical characteristics do not degrade.
Consider derating at higher operating temperatures. Choose the highest voltage class
compatible with derating at higher temperatures.
Surge currents beyond specified values will puncture a CTVS. In extreme cases a CTVS will
burst.
If steep surge current edges are to be expected, make sure your design is as low-inductance
as possible.
In some cases the malfunctioning of passive electronic components or failure before the end of
their service life cannot be completely ruled out in the current state of the art, even if they are
operated as specified. In applications requiring a very high level of operational safety and
especially when the malfunction or failure of a passive electronic component could endanger
human life or health (e.g. in accident prevention, life-saving systems, or automotive battery line
applications such as clamp 30), ensure by suitable design of the application or other measures
(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by
third parties in the event of such a malfunction or failure. Only use CTVS components from the
automotive series in safety-relevant applications.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 78 of 81
Multilayer varistors (MLVs)
Standard series
Specified values only apply to CTVS components that have not been subject to prior electrical,
mechanical or thermal damage. The use of CTVS devices in line-to-ground applications is
therefore not advisable, and it is only allowed together with safety countermeasures like
thermal fuses.
Storage
Only store CTVS in their original packaging. Do not open the package before storage.
Storage conditions in original packaging: temperature 25 to +45°C, relative humidity ≤75%
annual average, maximum 95%, dew precipitation is inadmissible.
Do not store CTVS devices where they are exposed to heat or direct sunlight. Otherwise the
packaging material may be deformed or CTVS may stick together, causing problems during
mounting.
Avoid contamination of the CTVS surface during storage, handling and processing.
Avoid storing CTVS devices in harmful environments where they are exposed to corrosive
gases for example (SOx, Cl).
Use CTVS as soon as possible after opening factory seals such as polyvinyl-sealed packages.
Solder CTVS components after shipment from EPCOS within the time specified:
CTVS with Ni barrier termination, 12 months
CTVS with AgPd and AgPt termination, 6 months
SHCV and CU series, 24 months
Handling
Do not drop CTVS components and allow them to be chipped.
Do not touch CTVS with your bare hands - gloves are recommended.
Avoid contamination of the CTVS surface during handling.
Mounting
When CTVS devices are encapsulated with sealing material or overmolded with plastic
material, electrical characteristics might be degraded and the life time reduced.
Make sure an electrode is not scratched before, during or after the mounting process.
Make sure contacts and housings used for assembly with CTVS components are clean before
mounting.
The surface temperature of an operating CTVS can be higher. Ensure that adjacent
components are placed at a sufficient distance from a CTVS to allow proper cooling.
Avoid contamination of the CTVS surface during processing.
Multilayer varistors (MLVs) with AgPd termination are not approved for lead-free soldering.
Soldering
Complete removal of flux is recommended to avoid surface contamination that can result in an
instable and/or high leakage current.
Use resin-type or non-activated flux.
Bear in mind that insufficient preheating may cause ceramic cracks.
Rapid cooling by dipping in solvent is not recommended, otherwise a component may crack.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 79 of 81
Multilayer varistors (MLVs)
Standard series
Conductive adhesive gluing
Only multilayer varistors (MLVs) with an AgPd termination are approved for conductive
adhesive gluing.
Operation
Use CTVS only within the specified operating temperature range.
Use CTVS only within specified voltage and current ranges.
Environmental conditions must not harm a CTVS. Only use them in normal atmospheric
conditions. Reducing the atmosphere (e.g. hydrogen or nitrogen atmosphere) is prohibited.
Prevent a CTVS from contacting liquids and solvents. Make sure that no water enters a CTVS
(e.g. through plug terminals).
Avoid dewing and condensation.
EPCOS CTVS components are mainly designed for encased applications. Under all
circumstances avoid exposure to:
direct sunlight
rain or condensation
steam, saline spray
corrosive gases
atmosphere with reduced oxygen content
EPCOS CTVS devices are not suitable for switching applications or voltage stabilization where
static power dissipation is required.
Multilayer varistors (MLVs) are designed for ESD protection and transient suppression.
CeraDiodes are designed for ESD protection only, ESD/EMI filters are designed for ESD and
EMI protection only.
This listing does not claim to be complete, but merely reflects the experience of EPCOS AG.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 80 of 81
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar
with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in
which the malfunction or failure of an electronic component could endanger human life or
health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by
means of suitable design of the customer application or other action taken by the customer
(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by
third parties in the event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order. We also
reserve the right to discontinue production and delivery of products. Consequently, we
cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the "General Terms of Delivery for Products and Services in the Electrical Industry" published by the German Electrical and Electronics Industry Association
(ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DeltaCap,
DigiSiMic, DSSP, FormFit, MiniBlue, MiniCell, MKK, MKD, MLSC, MotorCap, PCC,
PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL, SilverCap,
SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be
found on the Internet at www.epcos.com/trademarks.
Page 81 of 81
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
EPCOS:
B72500T0250K060 B72590T0110S160 B72510T0250K062 B72530T0500K062 B72580V0080L062
B72540V0080L062 B72580V0600K062 B72500T110K60 B72500T140K60 B72500T170K60 B72500T200K60
B72500T250K60 B72500T40M60 B72500T60M60 B72500T70M60 B72510T110K62 B72510T140K62
B72510T170K62 B72510T200K62 B72510T250K62 B72510T300K62 B72510T40M62 B72510T60M62
B72510T80L62 B72520T110K62 B72520T140K62 B72520T170K62 B72520T250K62 B72520T300K62
B72520T400K62 B72520T40M62 B72520T500K62 B72520T60M62 B72520T80L62 B72530T110K62
B72530T140K62 B72530T200K62 B72530T250K62 B72530T300K62 B72530T40M62 B72530T600K62
B72530T60M62 B72540V110K62 B72540V170K62 B72540V300K62 B72540V40M62 B72540V60M62
B72580V110K62 B72580V140K62 B72580V170K62 B72580V200K62 B72580V250K62 B72580V40M62
B72580V60M62 B72520T350K62 B72530T350K62 B72530T400K62 B72590T140L60 B72590T40M60
B72500T0060M60 B72500T0070K060 B72590T0110S360 B72590T0170S160