POWER INDUCTORS High-Reliability Power Inductors ML558PTA ■ High temperature materials allow operation in ambient temperatures up to 155°C. ■ Excellent current handling; very low DCR Core material Ferrite Terminations Tin-silver over tin over nickel over phos bronze (pins 1 and 2); Matte tin over nickel over phos bronze (pin 3). Weight 1.6 g Ambient temperature –55°C to +105°C with Irms current, +105°C to +155°C with derated current Storage temperature Component: –55°C to +155°C. Tape and reel packaging: –55°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Enhanced crush-resistant packaging 200/7″ reel Plastic tape: 24 mm wide,0.4 mm thick, 16 mm pocket spacing, 5.45 mm pocket depth SRF (MHz) Inductance2 DCR max3 Part number1 ±20% (µH) (mOhm) min typ ML558PTA331MLZ 0.33 4.0 119 170 ML558PTA801MLZ 0.80 4.0 70.0 100 ML558PTA102MLZ 1.0 4.0 66.5 95.0 ML558PTA122MLZ 1.2 6.0 63.7 91.0 ML558PTA132MLZ 1.3 4.0 56.7 81.0 ML558PTA152MLZ 1.5 6.0 52.5 75.0 ML558PTA182MLZ 1.8 6.0 49.0 70.0 ML558PTA202MLZ 2.0 9.0 45.5 65.0 ML558PTA222MLZ 2.2 4.0 40.6 58.0 ML558PTA252MLZ 2.5 7.5 38.5 55.0 ML558PTA322MLZ 3.2 6.0 37.1 53.0 ML558PTA402MLZ 4.0 9.0 32.9 47.0 ML558PTA432MLZ 4.3 7.5 30.8 44.0 ML558PTA572MLZ 5.7 9.0 24.5 35.0 4 Isat (A)5 10% drop 20% drop 30% drop 29.5 30.0 30.5 24.9 25.2 25.6 16.5 17.0 17.5 20.5 21.0 21.3 12.9 16.8 17.2 13.5 14.0 14.5 13.3 13.8 14.3 15.3 15.8 16.2 8.9 9.6 10.0 11.4 11.8 12.1 7.3 7.8 8.5 8.3 8.5 8.8 6.4 6.8 7.0 5.4 5.8 6.0 Irms (A)6 20°C rise 40°C rise 12.5 16.3 12.5 16.3 12.5 16.3 11.0 15.0 12.5 16.3 11.0 15.0 11.0 15.0 8.5 11.5 12.5 16.3 9.0 12.0 11.0 15.0 8.5 11.5 9.0 12.0 8.5 11.5 1. When ordering, please specify testing code: ML558PTA572MLZ Testing: Z = COTS H = Screening per Coilcraft CP-SA-10001 N = Screening per Coilcraft CP-SA-10004 2. Inductance measured at 100 kHz, 0.1 Vrms, 0 Adc on an Agilent/HP 4284A or equivalent. 3. DCR measured on a micro-ohmmeter. 4. SRF measured using an Agilent/HP 8753D network analyzer. 5. Typical DC current at which the inductance drops the specified amount from its value without current. 6. Typical current that causes the specified temperature rise from 25°C ambient. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Document ML535-1 Revised12/05/12 ® © Coilcraft, Inc. 2012 1102 Silver Lake Road Cary, IL 60013 Phone 800-981-0363 Fax 847-639-1508 Email [email protected] www.coilcraft-cps.com This product may not be used in medical or high risk applications without prior Coilcraft approval. Specifications subject to change without notice. Please check our web site for latest information. POWER INDUCTORS ML558PTA Series Typical L vs Frequency Typical L vs Current 7 7 5.7 µH 5 4 3.2 µH 3 2.0 µH 2 5.7 µH 6 Inductance (µH) Inductance (µH) 6 5 4 3.2 µH 3 2.0 µH 2 1.3 µH 1.3 µH 1 1 0.8 µH 0.8 µH 0 0.1 1 10 100 Frequency (MHz) 0 0.1 Irms Derating 1 Current (A) 10 1 0.433 ±0.008 11,0 ±0,2 2 120 110 3 Terminal 3 is for mounting stability only. 0.402 ±0.008 10,2 ±0,2 100 90 80 70 60 0.205 max 5,20 50 40 25°C Percent of rated Irms 100 30 0.075 ±0.004 1,90 ±0,1 20 0.075 ±0.004 1,90 ±0,1 Suggested Land Pattern 10 0 -55 -40 -20 0 20 40 60 80 100 120 140 160 Ambient temperature (°C) 0.083 ±0.004 2,10 ±0,1 1 0.152 3,85 0.083 ±0.004 2,10 ±0,1 0.083 ±0.004 2,10 ±0,1 inches Dimensions are in mm 0.091 2,30 3 0.215 5,47 0.134 3,40 2 Document ML535-2 Revised12/05/12 ® © Coilcraft, Inc. 2012 0.118 3,00 0.118 0.125 3,00 3,18 1102 Silver Lake Road Cary, IL 60013 Phone 800-981-0363 Fax 847-639-1508 Email [email protected] www.coilcraft-cps.com This product may not be used in medical or high risk applications without prior Coilcraft approval. Specifications subject to change without notice. Please check our web site for latest information.