ComLink™ Series CY2DL814 1:4 Clock Fanout Buffer Features • • • • • • • • Low-voltage operation VDD = 3.3V 1:4 Fanout Single-input configurable for — LVDS, LVPECL, or LVTTL The Cypress CY2 series of network circuits is produced using advanced 0.35-micron CMOS technology, achieving the industry’s fastest logic. The Cypress CY2DL814 fanout buffer features a single LVDS-, LVPECL-, or LVTTL-compatible input and four LVDS output pairs. — Four differential pairs of LVDS outputs Drives 50- or 100-ohm load (selectable) Low input capacitance Low output skew Does not exceed Bellcore 802.3 standards Operation at ⇒ 350 MHz – 700 Mbps Low propagation delay Typical (tpd < 4 ns) Industrial versions available Packages available include TSSOP/SOIC Designed for data-communication clock management applications, the fanout from a single input reduces loading on the input clock. The CY2DL814 is ideal for both level translations from single ended to LVDS and/or for the distribution of LVDS-based clock signals. The Cypress CY2DL814 has configurable input and output functions. The input can be selectable for LVPECL/LVTTL or LVDS signals while the output driver’s support standard and high drive LVDS. Drive either a 50-ohm or 100-ohm line with a single part number/device. Block Diagram Pin Configuration EN1 EN2 EN1 1 2 3 4 5 6 7 8 CONFIG Q1A Q1B CNTRL VDD GND Q2A Q2B IN+ IN- IN+ INEN2 LVDS / LVPECL / LVTTL Q3A Q3B CY2DL814 • • • • Description 16 15 14 13 12 11 10 9 Q1A Q1B Q2A Q2B Q3A Q3B Q4A Q4B 16-pin TSSOP/SOIC CONFIG Q4A Q4B OUTPUT CNTRL LVDS Cypress Semiconductor Corporation Document #: 38-07057 Rev. *A • 3901 North First Street • San Jose • CA 95134 • 408-943-2600 Revised December 14, 2002 ComLink™ Series CY2DL814 Pin Description Pin Number Pin Name Pin Standard Interface Description 6,7 IN+, IN– Configurable 3 CNTRL LVTTL/LVCMOS Converts into a High drive driver from a standard LVDS. Standard drive (logic = 0) B/High drive/Bus (logic = 1) 2 CONFIG LVTTL/LVCMOS Converts inputs (IN+/IN–), (EN, EN#) from the default LVPECL/LVDS (logic = 0) To LVTTL/LVCMOS (logic = 1) Differential input pair or single line. LVPECL default. See config below. 1,8 EN1, EN2 LVTTL/LVCMOS 16,15,14,13 12,11,10,9 Q1A, Q1B, Q2A, Q2B, Q3A, Q3B, Q4A, Q4B LDVS Enable/disable logic. See Table 1 below for details. 4 VDD POWER Positive supply voltage 5 GND POWER Ground Differential outputs. Maximum Ratings[1][2] Storage Temperature: ................................–65°C to + 150°C (Outputs only) ........................................ –0.3V to VDD + 0.3V Ambient Temperature:................................... –40°C to +85°C DC Input Voltage ................................... –0.3V to VDD + 0.3V Supply Voltage to Ground Potential DC Output Voltage................................. –0.3V to VDD + 0.9V (Inputs and VCC only)....................................... –0.3V to 4.6V Power Dissipation........................................................ 0.75W Supply Voltage to Ground Potential Table 1. EN1 EN2 Function Table–Differential Input Mode Enable Logic Input EN1 EN2 IN+ H X H X X L X L L H Outputs IN– QnA QnB H L H L L H L H H L H L L H L H X X Z Z Table 2. Output Drive Control for Standard and Bus/B/High Drive B CNTRL Pin 3 Binary Value Drive STD Impedance 0 Standard 100 ohm Output Voltage Value 50 ohm V = 1/2 * V0 1 High Drive/Bus/B 100 ohm V = 2 * V0 50 ohm V = V0 V0 = Voutput Note: 1. Stresses greater than those listed under absolute maximum ratings may cause permanent damage to the device. This is intended to be a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. Multiple Supplies: The voltage on any input or I/O pin cannot exceed the power pin during power-up. Power supply sequencing is NOT required. Document #: 38-07057 Rev. *A Page 2 of 8 ComLink™ Series CY2DL814 Table 3. Input Receiver Configuration for Differential or LVTTL/LVCMOS CONFIG Pin 2 Binary Value Input Receiver Family Input Receiver Type 1 LVTTL in LVCMOS Single-ended, Non-inverting, Inverting, Void of Bias Resistors 0 LVDS Low-voltage Differential Signaling LVPECL Low-voltage Pseudo (Positive) Emitter Coupled Logic Table 4. Function Control of the TTL Input Logic Used to Accept or Invert the Input Signal LVTTL/LVCMOS Input Logic Input Condition Ground Input Logic Output Logic Q Pins, Q1A or Q1 Input True Input Invert Input True Input Invert IN– Pin 7 IN+ Pin 6 VCC IN– Pin 7 IN+ Pin 6 Ground IN+ Pin 6 IN– Pin 7 IN+ Pin 6 VCC IN– Pin 7 Table 5. Power Supply Characteristics Typ. Max. Unit ICCD Parameter Dynamic Power Supply Current Description VDD = Max. Input toggling 50% Duty Cycle, Outputs Open Test Conditions Min. 1.5 2.0 mA/MHz IC Total Power Supply Current VDD = Max. Input toggling 50% Duty Cycle, Outputs Open fL=100 MHz 90 100 mA Min. Typ. Max. Unit Table 6. D.C Electrical Characteristics: 3.3V–LVDS Input Parameter Description Conditions VID Magnitude of Differential Input Voltage VIC Common-mode of Differential Input Voltage IVIDI (min. and max.) 100 VIH Input High Voltage Guaranteed Logic High Level VIL Input Low Voltage Guaranteed Logic Low Level IIH Input High Current VDD = Max. VIN = VDD IIL Input Low Current VDD = Max. VIN = VSS II Input High Current VDD = Max., VIN = VDD(max.) IVIDI/2 Config/Cntrl Pins 600 2.4–(IVIDI/2) 2 mV V V 0.8 V ±10 ±20 µA ±10 ±20 µA ±20 µA Table 7. D.C Electrical Characteristics: 3.3V–LVPECL Input Parameter Description VID Differential Input Voltage p-p VCM Common-mode Voltage Conditions Min. Guaranteed Logic High Level Typ. Max. Unit 400 2600 mV 1.65 2.25 V IIH Input High Current VDD = Max. VIN = VDD ±10 ±20 µA IIL Input Low Current VDD = Max. VIN = VSS ±10 ±20 µA II Input High Current VDD = Max., VIN = VDD(Max.) ±20 µA Document #: 38-07057 Rev. *A Page 3 of 8 ComLink™ Series CY2DL814 Table 8. D.C Electrical Characteristics: 3.3V–LVTTL/LVCMOS Input Parameter Description Conditions VIH Input High Voltage Guaranteed Logic High Level VIL Input Low Voltage Guaranteed Logic Low Level Min. Typ. Max. Unit 0.8 V 2 V IIH Input High Current VDD = Max. VIN = 2.7V 1 µA IIL Input Low Current VDD = Max. VIN = 0.5V –1 µA II Input High Current VDD = Max., VIN = VDD(Max.) 20 µA VIK Clamp Diode Voltage VDD = Min., IIN = –18 mA –1.2 V VH Input Hysteresis –0.7 80 mV Table 9. D.C Electrical Characteristics: 3.3V–LVDS OUTPUT Parameter Description Conditions I VOD I Differential output voltage p-p VDD = 3.3V, VIN = VIH, or VIL VOC(SS) Steady-state common-mode output voltage Delta VOC(SS) Change in VOC(SS) between logic states VOC(PP) Peak to peak common mode output voltage IOS Output short circuit Voh Output voltage high Vol Output voltage low Min. RL = 100 ohm Typ. Max. 0.25 –50 3 QA = 0V or QB = 0V RL = 100 ohm Unit 0.45 V 226 mV 50 mV 150 mV –20 mA 1475 925 mV mV Table 10. AC Parameters Parameter Rise Time Description Conditions Pin control (pin 3) logic is “FALSE” CL–10 pF defaulting to 100 ohm output drivers. RL and CL to GND 3 CL = Cintrinsic and Cexternal Differential 20% to 80% Min. Typ. Max. Unit RL = 100 ohm 1.4 ns 1.4 ns 350 600 ps 350 600 ps Fall Time Rise Time Pin control (pin 3) logic is “True” defaulting to 50 ohm output drivers. Differential 20% to 80% CL–10 pF RL and CL to GND 3 CL = Cintrinsic and Cexternal RL = 50 ohm Output boost Fall Time Table 11. AC Switching Characteristics @ 3.3 V (VDD = 3.3V ±5%, Temperature = –40°C to +85°C) Parameter Description Conditions Min. Typ. Max. Unit IN [+,-] to Q[A,B] Data and Clock Speed tPLH Propagation Delay – Low to High 3 4 5 ns tPHL Propagation Delay – High to Low VOD = 100 mV 3 4 5 ns Tpd Propagation Delay 3 4 5 ns IN [1,2] to Q[A,B] Control Speed TPe Enable (EN) to functional operation 6 ns Tpd Functional operation to Disable 5 ns 0.2 ns Q[A,B] Output Skews tSK(0) Output Skew: Skew between outputs of the same package (in phase) tSK(p) Pulse Skew: Skew between opposite transitions of the same output (tPHL–tPLH) tSK(t) Package Skew: Skew between outputs of different VID = 100 mV packages at the same power supply voltage, temperature and package type. Same input signal level and output load. Document #: 38-07057 Rev. *A 0.2 ns 1 ns Page 4 of 8 ComLink™ Series CY2DL814 Table 12. High Frequency Parametrics Max. Unit Fmax Parameter Maximum frequency VDD = 3.3V Description 50% duty cycle tW(50–50) Standard Load Circuit. Conditions Min. 400 MHz Fmax(20) Maximum frequency VDD = 3.3 V 20% duty cycle tW(50–50) LVPECL Input VIN = VIH(Max.)/VIL(Min.) VOUT = VOH(Min.)/VOL (Max.) (Limit) 200 MHz TW Minimum pulse VDD = 3.3 V LVPECL Input VIN = VIH(Max.)/VIL(Min.) F= 100 MHz VOUT = VOH(Min.)/VOL(Max.)(Limit) 1 A ns TPA Pulse 50 10pF Generator Typ. TPC B 50 TPB Standard Termination V1A 1.4 V 1.2 V CM 0V Differential V1B 1.0 V V0Y 1.4 V 1.2 V CM 0V Differential 1.0 V V0Z T PLH TPHL 80% 0V Differential V0Y - V0Z 20% tR tF Figure 1. Differential Receiver to Driver Propagation Delay and Driver Transition Time[3,4,5,6] A TPA 50 Pulse Generator TPC B 50 TPB VOC Standard Termination VI(A) 2.0V VI(B) 1.6V VOD Next Device Figure 2. Test Circuit and Voltage Definitions for the Driver Common-mode Output Voltage[3,4,5,6] Notes: 3. All input pulses are supplied by a frequency generator with the following characteristics: tR and tF ≤ 1 ns; pulse rerate = 50 Mpps; pulse width = 10 ± 0.2 ns. 4. RL= 50 ohm ± 1% Zline = 50 ohm 6”. 5. CL includes instrumentation and fixture capacitance within 6 mm of the UT. 6. TPA and B are used for prop delay and Rise/Fall measurements. TPC is used for VOC measurements only and is otherwise connected to VDD- 2. Document #: 38-07057 Rev. *A Page 5 of 8 ComLink™ Series CY2DL814 A TPA Pulse Generator 50 10pF TPC B 50 TPB Standard Termination VI(A) 1.4V VI(B) 1.0V 100% 80% 0.0V 20% 0% tF tR Figure 3. Test Circuit and Voltage Definitions for the Differential Output Signal[3,4,5,6] INPUT A LVPECL & LVDS LVCM OS / LVTTL INPUT B GND In C o n fig InConfig 0 1 L V D S /L V P E C L LVTTL/LVCMOS Figure 4. LVCMOS/LVTTL Single-ended Input Value[7] Figure 5. LVPECL or LVDS Differential Input Value[8] Ordering Information Part Number CY2DL814ZI Package Type Product Flow 16-pin TSSOP Industrial, –40°C to 85°C CY2DL814ZIT 16-pin TSSOP–Tape and Reel Industrial, –40°C to 85°C CY2DL814SI 16-pin SOIC Industrial, –40°C to 85°C CY2DL814SIT 16-pin SOIC–Tape and Reel Industrial, –40°C to 85°C CY2DL814ZC 16-pin TSSOP Commercial, 0°C to 70 °C CY2DL814ZCT 16-pin TSSOP–Tape and Reel Commercial, 0°C to 70 °C CY2DL814SC 16-pin SOIC Commercial, 0°C to 70 °C CY2DL814SCT 16-pin SOIC–Tape and Reel Commercial, 0°C to 70 °C Notes: 7. LVCMOS/LVTTL single ended input value. Ground either input: when on the B side then non-inversion takes place. If A side is grounded, the signal becomes the complement of the input on B side. See Table 4. 8. LVPECL or LVDS differential input value. Document #: 38-07057 Rev. *A Page 6 of 8 ComLink™ Series CY2DL814 Package Drawing and Dimensions 16-lead (150-mil) Molded SOIC S16 51-85068-A 16-lead Thin Shrunk Small Outline Package (4.40 MM Body) Z16 51-85091 ComLink is a trademark of Cypress Semiconductor Corporation. All product and company names mentioned in this document are the trademarks of their respective holders. Document #: 38-07057 Rev. *A Page 7 of 8 © Cypress Semiconductor Corporation, 2002. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges. ComLink™ Series CY2DL814 Document Title: ComLink™ Series CY2DL814 1:4 Clock Fanout Buffer Document Number: 38-07057 REV. ECN NO. Issue Date Orig. of Change ** 115362 07/10/02 EHX New Data Sheet *A 122744 12/14/02 RBI Added power up requirements to maximum ratings information. Document #: 38-07057 Rev. *A Description of Change Page 8 of 8