ON NCV8508DW50R2 5.0 v, 250 ma ldo with watchdog and reset Datasheet

NCV8508
5.0 V, 250 mA LDO with
Watchdog and RESET
The NCV8508 is a precision micropower Low Dropout (LDO)
voltage regulator. The part contains many of the required operational
requirements for powering microprocessors. Its robustness makes it
suitable for severe automotive environments. In addition to being a
good fit for the automotive environment, the NCV8508 is ideal for use
in battery operated, microprocessor controlled equipment because of
its extremely low quiescent current.
http://onsemi.com
MARKING
DIAGRAMS
16
16
Features
•
•
•
•
•
•
•
•
•
•
Output Voltage: 5.0 V
±3.0% Output Voltage
IOUT Up to 250 mA
Quiescent Current Independent of Load
Micropower Compatible Control Functions:
♦ Wakeup
♦ Watchdog
♦ RESET
Low Quiescent Current (100 A typ)
Protection Features:
♦ Thermal Shutdown
♦ Short Circuit
♦ 45 V Operation
Internally Fused Leads in SO−16L Package
NCV Prefix for Automotive and Other Applications Requiring Site
and Control Changes
Pb−Free Package is Available*
NCV85085
1
SO−16L
DW SUFFIX
CASE 751G
AWLYYWW
1
NCV85085
AWLYYWW
D2PAK−7
DPS SUFFIX
CASE 936AB
A
WL
YY
WW
1
= Assembly Location
= Wafer Lot
= Year
= Work Week
PIN CONNECTIONS
1
SO−16L
NC
NC
NC
GND
GND
NC
Sense
VOUT
D2PAK−7
16
Delay
RESET
Wakeup
GND
GND
WDI
NC
VIN
Tab = GND
Lead 1. VOUT
2. VIN
3. WDI
4. GND
5. Wakeup
6. RESET
7. Delay
1
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
 Semiconductor Components Industries, LLC, 2004
August, 2004 − Rev. 20
1
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 10 of this data sheet.
Publication Order Number:
NCV8508/D
NCV8508
MRA4004T3
C1*
0.1 F
VOUT
VIN
C2
1.0 F
WDI
VDD
I/O
NCV8508
Delay
RESET
RESET
GND
WAKEUP
I/O
RDelay
60 k
Microprocessor
VBAT
*C1
* required if regulator is located far from power supply filter.
.
Figure 1. Application Circuit
MAXIMUM RATINGS
Rating
Value
Unit
Input Voltage, VIN
−0.3 to 45
V
Output Voltage, VOUT
−0.3 to 18
V
2.0
200
kV
V
−0.3 to +7.0
V
−40 to150
°C
−55 to +150
°C
Junction−to−Case, RJC
Junction−to−Ambient, RJA
18
80
°C/W
°C/W
Junction−to−Case, RJC
Junction−to−Ambient, RJA
4.0
10 to 50 (Note 2)
°C/W
°C/W
Reflow: (SMD styles only) (Note 1)
240 peak (Note 3)
°C
ESD Susceptibility:
Human Body Model
Machine Model
Logic Inputs/Outputs (RESET, WDI, Wakeup)
Operating Junction Temperature, TJ
Storage Temperature Range, TS
Package Thermal Resistance, SO−16L:
Package Thermal Resistance, D2PAK, 7−Lead:
Lead Temperature Soldering:
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit
values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
1. 60 second maximum above 183°C.
2. Depending on thermal properties of substrate RJA = RJC + RJCA.
3. −5°C/+0°C allowable conditions.
http://onsemi.com
2
NCV8508
ELECTRICAL CHARACTERISTICS (−40°C ≤ TJ ≤ 125°C; 6.0 V ≤ VIN ≤ 28 V, 100 A ≤ IOUT ≤ 150 mA, C2 = 1.0 F, RDelay = 60 k;
unless otherwise specified.)
Characteristic
Test Conditions
Min
Typ
Max
Unit
−
4.85
5.00
5.15
V
OUTPUT
Output Voltage
Dropout Voltage (VIN − VOUT)
IOUT = 150 mA. Note 4
−
450
900
mV
Load Regulation
VIN = 14 V, 100 A ≤ IOUT ≤ 150 mA
−
5.0
30
mV
Line Regulation
6.0 V ≤ VIN ≤ 28 V, IOUT = 5.0 mA
−
5.0
50
mV
−
250
400
−
mA
Thermal Shutdown
Guaranteed by Design
150
180
210
°C
Quiescent Current
VIN = 12 V, IOUT = 150 mA, (see Figure 6)
−
100
150
A
4.50
4.65
4.80
V
−
0.2
0.4
0.4
0.8
V
VOUT − 0.5
VOUT − 1.0
VOUT − 0.25
VOUT − 0.5
−
V
2.0
−
3.0
6.0
4.0
−
ms
ms
Current Limit
RESET
Threshold
−
Output Low
RLOAD = 10 k to VOUT, VOUT ≥ 1.0 V
RLOAD = 5.1 k to VOUT, VOUT ≥ 1.0 V
Output High
RLOAD = 10 k to GND
RLOAD = 5.1 k to GND
Delay Time
VIN = 14 V, RDelay = 60 k, IOUT = 5.0 mA
VIN = 14 V, RDelay = 120 k, IOUT = 5.0 mA
WATCHDOG INPUT
Threshold High
−
70
−
−
%VOUT
Threshold Low
−
−
−
30
%VOUT
Hysteresis
−
−
100
−
mV
−
0.1
+10
A
5.0
−
−
s
Input Current
WDI = 6.0 V
Pulse Width
50% WDI falling edge to
50% WDI rising edge and
50% WDI rising edge to
50% WDI falling edge, (see Figure 5)
WAKEUP OUTPUT (VIN = 14 V, IOUT = 5.0 mA)
Wakeup Period
See Figures 4 and 5, RDELAY = 60 k
See Figures 4 and 5, RDELAY = 120 k
18
−
25
50
32
−
ms
ms
Wakeup Duty Cycle Nominal
See Figure 3
45
50
55
%
RESET HIGH to
Wakeup Rising Delay Time
RDELAY = 60 k
50% RESET rising edge to
50% Wakeup edge, RDELAY = 120 k
(see Figures 3 and 4)
9.0
−
12.5
25
16
−
ms
ms
Wakeup Response to
Watchdog Input
50% WDI falling edge to
50% Wakeup falling edge
−
0.1
5.0
s
Wakeup Response to RESET
50% RESET falling edge to
50% Wakeup falling edge.
VOUT = 5.0 V→ 4.5 V
−
0.1
5.0
s
Output Low
RLOAD = 10 k to VOUT, VOUT ≥ 1.0 V
RLOAD = 5.1 k to VOUT, VOUT ≥ 1.0 V
−
0.2
0.4
0.4
0.8
V
Output High
RLOAD = 10 k to GND
RLOAD = 5.1 k to GND
VOUT − 0.5
VOUT − 1.0
VOUT − 0.25
VOUT − 0.5
−
V
IDELAY = 50 A. Note 5
−
1.25
−
V
DELAY
Output Voltage
4. Measured when the output voltage has dropped 100 mV from the nominal value. (see Figure 12)
5. Current drain on the Delay pin directly affects the Delay Time, Wakeup Period, and the RESET to Wakeup Delay Time.
http://onsemi.com
3
NCV8508
PACKAGE PIN DESCRIPTION
PACKAGE PIN #
D2PAK−7
SO−16L
PIN SYMBOL
1
8
VOUT
2
9
VIN
Supply Voltage to the IC.
3
11
WDI
CMOS compatible input lead. The Watchdog function monitors the falling
edge of the incoming signal.
4
4, 5, 12, 13
GND
Ground connection.
5
14
Wakeup
CMOS compatible output consisting of a continuously generated signal used
to “wake up” the microprocessor from sleep mode.
6
15
RESET
CMOS compatible output lead RESET goes low whenever VOUT drops by
more than 7.0% from nominal, or during the absence of a correct Watchdog
signal.
7
16
Delay
−
1−3, 6, 10
NC
−
7
Sense
FUNCTION
Regulated output voltage ± 3.0%.
Buffered bandgap voltage used to create timing current for RESET and
Wakeup from RDelay.
No Connection.
Kelvin connection which allows remote sensing of the output voltage for
improved regulation. Connect to VOUT if remote sensing is not required.
VIN
−
Internally
connected
on 7 lead
D2PAK
Charge
Pump
+
11 V
Sense
Current
Limit
1.25 V
Bandgap
Reference
VOUT
Thermal
Shutdown
+
−
−
RESET
+
Watchdog
Circuit
WDI
Falling
Edge
Detect
Delay
Timing
Circuit
Wakeup
Circuit
Figure 2. Block Diagram
http://onsemi.com
4
Wakeup
NCV8508
TIMING DIAGRAMS
VIN
RESET
Wakeup
Duty Cycle = 50%
Wakeup
WDI
VOUT
WDI Pulse Must Occur with Wakeup in
Low State for 50% Duty Cycle.
Reference Figure 17 for Occurrence of
WDI with Wakeup in High State.
POR
RESET High
to Wakeup
Delay Time
Power Up
Microprocessor
Sleep Mode
Normal Operation with Varying Watchdog Signal
Figure 3. Power Up, Sleep Mode and Normal Operation
VIN
RESET Delay Time
RESET
Wakeup
WDI
VOUT
POR
RESET High
to Wakeup
Delay Time
Wakeup
Period
RESET High
to Wakeup
Delay Time
Figure 4. Error Condition: Watchdog Remains Low and a RESET Is Issued
RESET
Wakeup Period
Wakeup
WDI
RESET Threshold
VOUT
Watchdog
Pulse Width
Power Down
POR
POR
Watchdog Pulse Width
Figure 5. Power Down and Restart Sequence
http://onsemi.com
5
NCV8508
TYPICAL PERFORMANCE CHARACTERISTICS
120
−700
−40°C
VOUT Transient, mV
−600
IQ, A
110
+25°C
100
0
50
100
150
IOUT, mA
−400
−300
10 F
ESR = 3.4 −200
100 F
ESR = 1.3 −100
+125°C
90
1.0 F
ESR = 4.6 −500
200
0
250
0
Figure 6. Quiescent Current vs Output Current
100
150
Switching Current, mA
200
250
Figure 7. Load Transient Response
3.7
14
3.6
12
3.5
3.4
10
POR Delay, ms
POR Delay, ms
50
3.3
3.2
3.1
3.0
8
6
4
2.9
2
2.8
2.7
−40
−20
0
20
40
60
80
Temperature, °C
100
120
0
15
140
Figure 8. POR Delay vs Temp, RDELAY = 60 k
60
105
150
RDELAY, k
195
240
Figure 9. POR Delay vs RDELAY
100
27.0
90
26.5
70
RDELAY, ms
Wakeup Period, ms
80
26.0
25.5
25.0
24.5
60
50
40
30
24.0
20
23.5
23.0
−40
10
−20
0
20
40
60
80
Temperature (°C)
100
120
0
15
140
Figure 10. Wakeup Period vs Temp, RDELAY = 60 k
60
105
150
RDELAY, k
195
Figure 11. Wakeup Period vs RDELAY
http://onsemi.com
6
240
NCV8508
TYPICAL PERFORMANCE CHARACTERISTICS
5.10
1.0
0.9
Dropout Voltage (V)
Output Voltage (V)
+125°C
0.8
0.7
0.6
+25°C
0.5
−40°C
0.4
0.3
5.05
5.00
VIN = 14 V
IOUT = 5.0 mA
4.95
0.2
0.1
0.0
0
25
50
75
4.90
−40 −25 −10
100 125 150 175 200 225 250
Output Current (mA)
Figure 12. Dropout Voltage vs Output Current
5
20 35 50 65
Temperature (°C)
80
95 110 125
Figure 13. Output Voltage vs Temperature
1000
160
140
120
Unstable Region
100
ESR ()
IOUT (mA)
100
80
60
Stable Region
10
40
RL = 33 20
0
1.0
1.5
2.0
2.5
3.0
3.5 4.0
VIN (V)
4.5
5.0
5.5
C = 1.0 F, 10 F
1
6.0
0
5
10
15
20
25
30
35
40
45
Output Current (mA)
Figure 14. Output Current vs Input Voltage
Figure 15. Output Capacitor ESR
DEFINITION OF TERMS
such that the average chip temperature is not significantly
affected.
Load Regulation: The change in output voltage for a
change in load current at constant chip temperature.
Quiescent Current: The part of the positive input current
that does not contribute to the positive load current. The
regulator ground lead current.
Ripple Rejection: The ratio of the peak−to−peak input
ripple voltage to the peak−to−peak output ripple voltage.
Current Limit: Peak current that can be delivered to the
output.
Dropout Voltage: The input−output voltage differential at
which the circuit ceases to regulate against further reduction
in input voltage. Measured when the output voltage has
dropped 100 mV from the nominal value obtained at 14 V
input, dropout voltage is dependent upon load current and
junction temperature.
Input Voltage: The DC voltage applied to the input
terminals with respect to ground.
Line Regulation: The change in output voltage for a
change in the input voltage. The measurement is made under
conditions of low dissipation or by using pulse techniques
http://onsemi.com
7
NCV8508
DETAILED OPERATING DESCRIPTION
RESET is independent of VIN and operates correctly to an
output voltage as low as 1.0 V. A signal is issued in any of
three situations. During power up the RESET is held low
until the output voltage is in regulation. During operation if
the output voltage shifts below the regulation limits, the
RESET toggles low and remains low until proper output
voltage regulation is restored. And finally, a RESET signal
is issued if the regulator does not receive a Watchdog signal
within the Wakeup period.
The RESET pulse width, Wakeup signal frequency, and
Wakeup delay time are all set by one external resistor,
RDelay.
The Delay pin is a buffered bandgap voltage (1.25 V). It
can be used as a reference for an external tracking regulator
as shown in Figure 16.
The regulator is protected against short circuit and thermal
runaway conditions. The device runs through 45 volt
transients, making it suitable for use in automotive
environments.
The NCV8508 is a precision micropower voltage
regulator with very low quiescent current (100 A typical at
250 mA load). A typical dropout voltage is 450 mV at
150 mA. Microprocessor control logic includes Watchdog,
Wakeup and RESET. This unique combination of extremely
low quiescent current and full microprocessor control
makes the NCV8508 ideal for use in battery operated,
microprocessor controlled equipment in addition to being a
good fit in the automotive environment.
The NCV8508 Wakeup function brings the
microprocessor out of Sleep mode. The microprocessor in
turn, signals its Wakeup status back to the NCV8508 by
issuing a Watchdog signal.
The Watchdog logic function monitors an input signal
(WDI) from the microprocessor. The NCV8508 responds to
the falling edge of the Watchdog signal which it expects at
least once during each Wakeup period. When the correct
Watchdog signal is received, a falling edge is issued on the
Wakeup signal line.
MRA4004T3
200 mA
VIN
VIN
VBAT
0.1 F
1.0 F
NCV8508
12 k
CS8182
Adj
3.9 k
Delay
GND
VREF/ENABLE
60 k
0.1 F
Figure 16. Application Circuit
http://onsemi.com
8
5V
VOUT
GND
10 F
NCV8508
CIRCUIT DESCRIPTION
Functional Description
Resistor temperature coefficient and tolerance as well as
the tolerance of the NCV8508 must be taken into account in
order to get the correct system tolerance for each parameter.
To reduce the drain on the battery a system can go into a
low current consumption mode when ever its not performing
a main routine. The Wakeup signal is generated
continuously and is used to interrupt a microcontroller that
is in sleep mode. The nominal output is a 5.0 volt square
wave (voltage generated from VOUT) with a duty cycle of
50% at a frequency that is determined by a timing resistor,
RDelay.
When the microprocessor receives a rising edge from the
Wakeup output, it must issue a Watchdog pulse and check its
inputs to decide if it should resume normal operations or
remain in the sleep mode.
The first falling edge of the Watchdog signal causes the
Wakeup to go low within 2.0 s (typ) and remain low until
the next Wakeup cycle (see Figure 17). Other Watchdog
pulses received within the same cycle are ignored (Figure 3).
During power up, RESET is held low until the output
voltage is in regulation. During operation, if the output
voltage shifts below the regulation limits, the RESET
toggles low and remains low until proper output voltage
regulation is restored. After the RESET delay, RESET
returns high.
The Watchdog circuitry continuously monitors the input
Watchdog signal (WDI) from the microprocessor. The
absence of a falling edge on the Watchdog input during one
Wakeup cycle will cause a RESET pulse to occur at the end
of the Wakeup cycle. (see Figure 4).
The Wakeup output is pulled low during a RESET
regardless of the cause of the RESET. After the RESET
returns high, the Wakeup cycle begins again (see Figure 4).
The RESET Delay Time, Wakeup signal frequency and
RESET high to Wakeup delay time are all set by one external
resistor RDelay.
Wakeup Period = (4.17 × 10−7)RDelay
RESET Delay Time = (5.21 × 10−8)RDelay
RESET HIGH to Wakeup Delay Time = (2.08 × 10−7)RDelay
WDI
Wakeup
Wakeup
Response
to WDI
Figure 17. Wakeup Response to WDI
RESET
Wakeup
Wakeup
Response
to RESET
Figure 18. Wakeup Response to RESET (Low
Voltage)
http://onsemi.com
9
NCV8508
APPLICATION NOTES
Calculating Power Dissipation in a Single Output
Linear Regulator
Thermal Resistance,
Junction to Ambient, RJA, (°C/W)
100
The maximum power dissipation for a single output
regulator (Figure 19) is:
PD(max) [VIN(max) VOUT(min)] IOUT(max)
(1)
VIN(max)IQ
where:
VIN(max) is the maximum input voltage,
VOUT(min) is the minimum output voltage,
IOUT(max) is the maximum output current for the
application, and
IQ is the quiescent current the regulator consumes at
IOUT(max).
SMART
REGULATOR
VIN
80
70
60
50
40
0
0.5
1.0
1.5
2.0
Copper Area (inch2)
2.5
3.0
Figure 20. 16 Lead SOW (4 Leads Fused), JA as
a Function of the Pad Copper Area (2 oz. Cu
Thickness), Board Material = 0.0625 G−10/R−4
IOUT
IIN
90
VOUT
} Control
Features
Heatsinks
A heatsink effectively increases the surface area of the
package to improve the flow of heat away from the IC and
into the surrounding air.
Each material in the heat flow path between the IC and the
outside environment will have a thermal resistance. Like
series electrical resistances, these resistances are summed to
determine the value of RJA:
IQ
Figure 19. Single Output Regulator with Key
Performance Parameters Labeled
Once the value of PD(max) is known, the maximum
permissible value of RJA can be calculated:
T
RJA 150°C A
PD
RJA RJC RCS RSA
(3)
where:
RJC = the junction−to−case thermal resistance,
RCS = the case−to−heatsink thermal resistance, and
RSA = the heatsink−to−ambient thermal resistance.
RJC appears in the package section of the data sheet. Like
RJA, it too is a function of package type. RCS and RSA are
functions of the package type, heatsink and the interface
between them. These values appear in heatsink data sheets
of heatsink manufacturers.
(2)
The value of RJA can then be compared with those in the
package section of the data sheet. Those packages with
RJA’s less than the calculated value in Equation 2 will keep
the die temperature below 150°C.
In some cases, none of the packages will be sufficient to
dissipate the heat generated by the IC, and an external
heatsink will be required.
ORDERING INFORMATION
Device
NCV8508DW50
NCV8508DW50G
NCV8508DW50R2
NCV8508D2T50
NCV8508D2T50G
NCV8508D2T50R4
Output Voltage
Package
Shipping†
5.0 V
SO−16L
47 Units / Rail
5.0 V
SO−16L
(Pb−Free)
47 Units / Rail
5.0 V
SO−16L
1000 / Tape & Reel
5.0 V
D2PAK−7
50 Units / Rail
D2PAK−7
50 Units / Rail
5.0 V
(Pb−Free)
D2PAK−7
5.0 V
750 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
10
NCV8508
PACKAGE DIMENSIONS
SO−16L
DW SUFFIX
CASE 751G−03
ISSUE C
A
D
9
1
h X 45 MILLIMETERS
DIM MIN
MAX
A
2.35
2.65
A1 0.10
0.25
B
0.35
0.49
C
0.23
0.32
D 10.15 10.45
E
7.40
7.60
e
1.27 BSC
H 10.05 10.55
h
0.25
0.75
L
0.50
0.90
q
0
7
8
16X
M
14X
e
T A
S
B
S
L
A
0.25
B
B
A1
H
E
0.25
8X
M
B
M
16
SEATING
PLANE
T
NOTES:
1. DIMENSIONS ARE IN MILLIMETERS.
2. INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.5M, 1994.
3. DIMENSIONS D AND E DO NOT INLCUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.
5. DIMENSION B DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.13 TOTAL IN
EXCESS OF THE B DIMENSION AT MAXIMUM
MATERIAL CONDITION.
C
http://onsemi.com
11
NCV8508
PACKAGE DIMENSIONS
D2PAK−7 (SHORT LEAD)
DP SUFFIX
CASE 936AB−01
ISSUE O
TERMINAL 8
A
K
NOTES:
1. DIMENSIONS AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
U
E
S
B
DIM
A
B
C
D
E
G
H
K
L
M
N
P
R
S
U
V
V
M
H
L
P
D
G
N
R
INCHES
MIN
MAX
0.396
0.406
0.326
0.336
0.170
0.180
0.026
0.036
0.045
0.055
0.050 REF
0.539
0.579
0.055
0.066
0.000
0.010
0.100
0.110
0.017
0.023
0.058
0.078
0°
8°
0.095
0.105
0.256 REF
0.305 REF
MILLIMETERS
MIN
MAX
10.05
10.31
8.28
8.53
4.31
4.57
0.66
0.91
1.14
1.40
1.27 REF
13.69
14.71
1.40
1.68
0.00
0.25
2.54
2.79
0.43
0.58
1.47
1.98
0°
8°
2.41
2.67
6.50 REF
7.75 REF
C
SMART REGULATOR is a registered trademark of Semiconductor Components Industries, LLC (SCILLC).
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Phone: 81−3−5773−3850
http://onsemi.com
12
For additional information, please contact your
local Sales Representative.
NCV8508/D