3.2x2.4mm SMD CHIP LED LAMP Part Number: APBD3224LSURKSYKC Hyper Red Super Bright Yellow Features Descriptions z 3.2x2.4mm SMD LED, 2.4mm thickness. z The Hyper Red source color devices are made with Al GaInP on GaAs substrate Light Emitting Diode. z Low power consumption. z Ideal for backlight and indicator. z The Super Bright Yellow device is made with AlGaInP (on GaAs substrate) light emitting diode chip. z Package : 1500pcs / reel. z Moisture sensitivity level : level 3. z Low current IF=2mA operating. z RoHS compliant. Package Dimensions RED YELLOW Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAO4552 REV NO: V.1A DATE: AUG/01/2015 PAGE: 1 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203015160 Selection Guide Part No. Emitting Color (Material) Lens Type Viewing Angle [1] Iv (mcd) [2] @ 2mA Min. Typ. 20 50 10* 30* 20 50 20* 50* 2θ1/2 Hyper Red (AlGaInP) APBD3224LSURKSYKC Water Clear Super Bright Yellow (AlGaInP) 20° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. * Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Emitting Color λpeak Peak Wavelength Hyper Red Super Bright Yellow λD [1] Dominant Wavelength Δλ1/2 Min. Units Test Conditions 645 590 nm IF=2mA Hyper Red Super Bright Yellow 630 590 nm IF=2mA Spectral Line Half-width Hyper Red Super Bright Yellow 28 20 nm IF=2mA C Capacitance Hyper Red Super Bright Yellow 35 20 pF VF=0V;f=1MHz VF [2] Forward Voltage Hyper Red Super Bright Yellow 2.1 2.1 V IF=2mA IR Reverse Current Hyper Red Super Bright Yellow 10 10 uA VR = 5V 1.5 1.5 Typ. 1.75 1.85 Max. Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Hyper Red Super Bright Yellow Units Power dissipation 63 63 mW DC Forward Current 30 30 mA Peak Forward Current [1] 185 175 mA Reverse Voltage 5 Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C V Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAO4552 REV NO: V.1A DATE: AUG/01/2015 PAGE: 2 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203015160 APBD3224LSURKSYKC Hyper Red SPEC NO: DSAO4552 REV NO: V.1A DATE: AUG/01/2015 PAGE: 3 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203015160 Super Bright Yellow SPEC NO: DSAO4552 REV NO: V.1A DATE: AUG/01/2015 PAGE: 4 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203015160 APBD3224LSURKSYKC Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAO4552 REV NO: V.1A DATE: AUG/01/2015 PAGE: 5 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203015160 PACKING & LABEL SPECIFICATIONS APBD3224LSURKSYKC Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAO4552 REV NO: V.1A DATE: AUG/01/2015 PAGE: 6 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203015160