ACS374MS Radiation Hardened Octal D Flip-Flop, Three-State April 1995 Features Pinouts 20 LEAD CERAMIC DUAL-IN-LINE MIL-STD-1835 DESIGNATOR CDIP2-T20, LEAD FINISH C TOP VIEW • 1.25 Micron Radiation Hardened SOS CMOS • Total Dose 300K RAD (Si) • Single Event Upset (SEU) Immunity <1 x 10-10 Errors/Bit-Day (Typ) OE 1 Q0 2 19 Q7 D0 3 18 D7 • Dose Rate Upset >1011 RAD (Si)/s, 20ns Pulse D1 4 17 D6 • Latch-Up Free Under Any Conditions Q1 5 16 Q6 Q2 6 15 Q5 D2 7 14 D5 D3 8 13 D4 Q3 9 12 Q4 GND 10 11 CP • SEU LET Threshold >80 MEV-cm2/mg • Military Temperature Range: -55oC to +125oC • Significant Power Reduction Compared to ALSTTL Logic • DC Operating Voltage Range: 4.5V to 5.5V • Input Logic Levels - VIL = 30% of VCC Max 20 VCC 20 LEAD CERAMIC FLATPACK MIL-STD-1835 DESIGNATOR CDFP4-F20, LEAD FINISH C TOP VIEW - VIH = 70% of VCC Min • Input Current ≤1µA at VOL, VOH Description The Intersil ACS374MS is a radiation hardened octal D-type flipflop with three-state outputs. The eight edge-triggered flip-flops enter data into their registers on the low to high transition of clock (CP). The Output Enable (OEN) controls the three-state outputs and is independent of the register operation. When the OEN is high, the outputs will be in the high impedance state. The ACS374MS utilizes advanced CMOS/SOS technology to achieve high-speed operation. This device is a member of the radiation hardened, high-speed, CMOS/SOS Logic Family. OE 1 20 VCC Q0 2 19 Q7 D0 3 18 D7 D1 4 17 D6 Q1 5 16 Q6 Q2 6 15 Q5 D2 7 14 D5 D3 8 13 D4 Q3 9 12 Q4 10 11 CP GND Ordering Information PART NUMBER ACS374DMSR TEMPERATURE RANGE -55oC to +125oC SCREENING LEVEL Intersil Class S Equivalent Intersil Class S Equivalent Sample Sample Die -55oC to +125oC +25oC +25oC +25oC ACS374KMSR ACS374D/Sample ACS374K/Sample ACS374HMSR Truth Table Functional Diagram INPUTS OE CP OUTPUTS Dn Qn L H H L L L L X X Q0 H X X Z H = High Level L = Low Level Q0 X = Immaterial Z = High Impedance PACKAGE 20 Lead SBDIP 20 Lead Ceramic Flatpack 20 Lead SBDIP 20 Lead Ceramic Flatpack Die 1 OF 8 FF D D Q Q CP OE COMMON CONTROLS CP = Transition from Low to High Level = the level of Q before the indicated input conditions were established OE CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999 1 518820 File Number 3997 Spec Number Specifications ACS374MS Absolute Maximum Ratings Reliability Information Supply Voltage (VCC). . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +6.0V Input Voltage Range . . . . . . . . . . . . . . . . . . . . . .-0.5V to VCC +0.5V DC Input Current, Any One Input . . . . . . . . . . . . . . . . . . . . . . . .±10mA DC Drain Current, Any One Output. . . . . . . . . . . . . . . . . . . . . . .±50mA Storage Temperature Range (TSTG) . . . . . . . . . . . -65oC to +150oC Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . +265oC Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1 (All Voltages Reference to VSS) Thermal Impedance θJA θJC DIP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72oC/W 24oC/W Flatpack . . . . . . . . . . . . . . . . . . . . . . . . . . 107oC/W 28oC/W Maximum Package Power Dissipation at +125oC DIP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.7W Flatpack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5W Maximum Device Power Dissipation. . . . . . . . . . . . . . . . . . .(TBD)W Gate Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Gates CAUTION: As with all semiconductors, stress listed under “Absolute Maximum Ratings” may be applied to devices (one at a time) without resulting in permanent damage. This is a stress rating only. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. The conditions listed under “Electrical Performance Characteristics” are the only conditions recommended for satisfactory device operation. Operating Conditions Input High Voltage (VIH) . . . . . . . . . . . . . . . . . . VCC to 70% of VCC Input Low Voltage (VIL). . . . . . . . . . . . . . . . . . . . .0V to 30% of VCC Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V Input Rise and Fall Times at 4.5V VCC (TR, TF) . . . . . . 10ns/V Max Operating Temperature Range (TA) . . . . . . . . . . . . -55oC to +125oC TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS PARAMETER Supply Current Output Current (Source) Output Current (Sink) Output Voltage High Output Voltage Low Input Leakage Current Three-State Output Leakage Current Noise Immunity Functional Test GROUP A SUBGROUPS TEMPERATURE MIN MAX UNITS 1 +25oC - 20 µA 2, 3 +125oC, -55oC - 400 µA 1 +25oC -12 - mA 2, 3 +125oC, -55oC -8 - mA 1 +25oC 12 - mA 2, 3 +125oC, -55oC 8 - mA VCC = 5.5V, VIH = 3.85V VIL = 1.65V, IOH = -50µA 1, 2, 3 +25oC, +125oC, -55oC VCC -0.1 - V VCC = 4.5V, VIH = 3.15V, VIL = 1.35V, IOH = -50µA 1, 2, 3 +25oC, +125oC, -55oC VCC -0.1 - V VCC = 5.5V, VIH = 3.85V VIL = 1.65V, IOH = 50µA 1, 2, 3 +25oC, +125oC, -55oC - 0.1 V VCC = 4.5V, VIH = 3.15V, VIL = 1.35V, IOH = 50µA 1, 2, 3 +25oC, +125oC, -55oC - 0.1 V 1 +25oC - ±0.5 µA 2, 3 +125oC, -55oC - ±1.0 µA 1 +25oC - ±1 µA 2, 3 +125oC, -55oC - ±35 µA 7, 8A, 8B +25oC, +125oC, -55oC - - V (NOTE 1) CONDITIONS SYMBOL ICC IOH IOL VOH VOL IIN IOZ FN VCC = 5.5V, VIN = VCC or GND VCC = VIH = 4.5V, VOUT = VCC -0.4V, VIL = 0V, (Note 2) VCC = VIH = 4.5V, VOUT = 0.4V, VIL = 0V, (Note 2) VCC = 5.5V, VIN = VCC or GND VCC = 5.5V, Force Voltage = 0V or VCC VCC = 4.5V, VIH = 3.15V, VIL = 1.35V, (Note 3) LIMITS NOTES: 1. All voltages referenced to device GND. 2. Force/measure functions may be interchanged. 3. For functional tests, VO ≥4.0V is recognized as a logic “1”, and VO ≤0.5V is recognized as a logic “0”. Spec Number 2 518820 Specifications ACS374MS TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS PARAMETER Propagation Delay (NOTES 1, 2) CONDITIONS SYMBOL TPHL1 TPLH1 TPZL1 TPZH1 TPLZ1 TPHZ1 GROUP A SUBGROUPS TEMPERATURE MIN MAX UNITS 9 +25oC 2 14 ns 10, 11 +125oC, -55oC 2 17 ns 9 +25oC 2 16 ns 10, 11 +125oC, -55oC 2 20 ns 9 +25oC 2 15 ns 10, 11 +125oC, -55oC 2 19 ns 9 +25oC 2 16 ns 10, 11 +125oC, -55oC 2 20 ns 9 +25oC 2 15 ns 10, 11 +125oC, -55oC 2 19 ns 9 +25oC 2 15 ns 10, 11 +125oC, -55oC 2 19 ns VCC = 4.5V, VIH = 4.5V, VIL = 0V VCC = 4.5V, VIH = 4.5V, VIL = 0V VCC = 4.5V, VIH = 4.5V, VIL = 0V VCC = 4.5V, VIH = 4.5V, VIL = 0V VCC = 4.5V, VIH = 4.5V, VIL = 0V VCC = 4.5V, VIH = 4.5V, VIL = 0V LIMITS NOTES: 1. All voltages referenced to device GND. 2. AC measurements assume RL = 500Ω, CL = 50pF, Input TR = TF = 3ns. TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS LIMITS PARAMETER Capacitance Power Dissipation Input Capacitance Output Capacitance Pulse Width Time Setup Time Hold Time Maximum Frequency CP SYMBOL CPD CIN COUT TW TSU TH FMAX CONDITIONS VCC = 5.0V, VIH = 5.0V, VIL = 0V, f = 1MHz VCC = 5.0V, VIH = 5.0V, VIL = 0V, f = 1MHz NOTE TEMP MIN TYP MAX UNITS 1 +25oC - 25 - pF +125oC - 30 - pF +25oC - - 10 pF +125oC - - 10 pF +25oC - - 20 pF +125oC - - 20 pF +25oC 4.5 - - ns +125oC 5 - - ns +25oC 3.5 - - ns +125oC 4 - - ns +25oC 3.5 - - ns +125oC 4 - - ns +25oC 0 - 100 MHz +125oC 0 - 100 MHz 1 VCC = 5.0V, VIH = 5.0V, VIL = 0V, f = 1MHz 1 VCC = 4.5V, VIH = 4.5V, VIL = 0V 1 VCC = 4.5V, VIH = 4.5V, VIL = 0V 1 VCC = 4.5V, VIH = 4.5V, VIL = 0V 1 VCC = 4.5V, VIH = 4.5V, VIL = 0V 1 NOTE: 1. The parameters listed in Table 3 are controlled via design or process parameters. Min and Max Limits are guaranteed but not directly tested. These parameters are characterized upon initial design release and upon design changes which affect these characteristics. Spec Number 3 518820 Specifications ACS374MS TABLE 4. POST IRRADIATION ELECTRICAL PERFORMANCE CHARACTERISTICS RAD LIMITS PARAMETER (NOTE 1) CONDITIONS SYMBOL TEMP MIN MAX UNITS Supply Current ICC VCC = 5.5V, VIN = VCC or GND +25oC - 400 µA Output Current (Source) IOH VCC = VIH = 4.5V, VOUT = VCC -0.4V, VIL = 0 +25oC -8 - mA Output Current (Sink) IOL VCC = VIH = 4.5V, VOUT = 0.4V, VIL = 0 +25oC 8 - mA Output Voltage High VOH VCC = 5.5V, VIH = 3.85V, VIL = 1.65V, IOH = -50µA +25oC VCC -0.1 - V VCC = 4.5V, VIH = 3.15V, VIL = 1.35V, IOH = -50µA +25oC VCC -0.1 - V VCC = 5.5V, VIH = 3.85V, VIL = 1.65V, IOH = 50µA +25oC - 0.1 V VCC = 4.5V, VIH = 3.15V, VIL = 1.35V, IOH = 50µA +25oC - 0.1 V Output Voltage Low VOL Input Leakage Current IIN VCC = 5.5V, VIN = VCC or GND +25oC - ±1 µA Three-State Output Leakage Current IOZ VCC = 5.5V, Force Voltage = 0V or VCC +25oC - ±35 µA Noise Immunity Functional Test FN VCC = 4.5V, VIH = 3.15V, VIL = 1.35V, (Note 2) +25oC - - V TPHL1 VCC = 4.5V, VIH = 4.5V, VIL = 0V +25oC 2 17 ns TPLH1 VCC = 4.5V, VIH = 4.5V, VIL = 0V +25oC 2 20 ns TPZL1 VCC = 4.5V, VIH = 4.5V, VIL = 0V +25oC 2 19 ns TPZH1 VCC = 4.5V, VIH = 4.5V, VIL = 0V +25oC 2 20 ns TPLZ1 VCC = 4.5V, VIH = 4.5V, VIL = 0V +25oC 2 19 ns TPHZ1 VCC = 4.5V, VIH = 4.5V, VIL = 0V +25oC 2 19 ns Propagation Delay NOTES: 1. All voltages referenced to device GND. 2. For functional tests, VO ≥4.0V is recognized as a logic “1”, and VO ≤0.5V is recognized as a logic “0”. TABLE 5. DELTA PARAMETERS (+25oC) PARAMETER SYMBOL (NOTE1) DELTA LIMIT UNITS Supply Current ICC ±4.0 µA Three-State Leakage Current IOZ ±200 nA Output Current IOL/IOH ±15 % NOTE: 1. All delta calculations are referenced to 0 hour readings or pre-life readings. Spec Number 4 518820 Specifications ACS374MS TABLE 6. APPLICABLE SUBGROUPS CONFORMANCE GROUP METHOD GROUP A SUBGROUPS Initial Test (Preburn-In) 100%/5004 1, 7, 9 ICC, IOL/H, IOZL/H Interim Test 1 (Postburn-In) 100%/5004 1, 7, 9 ICC, IOL/H, IOZL/H Interim Test 2 (Postburn-In) 100%/5004 1, 7, 9 ICC, IOL/H, IOZL/H PDA 100%/5004 1, 7, 9, Deltas Interim Test 3 (Postburn-In) 100%/5004 1, 7, 9 PDA 100%/5004 1, 7, 9, Deltas Final Test 100%/5004 2, 3, 8A, 8B, 10, 11 Sample/5005 1, 2, 3, 7, 8A, 8B, 9, 10, 11 Subgroup B-5 Sample/5005 1, 2, 3, 7, 8A, 8B, 9, 10, 11, Deltas Subgroup B-6 Sample/5005 1, 7, 9 Sample/5005 1, 7, 9 Group A (Note 1) Group B Group D READ AND RECORD ICC, IOL/H, IOZL/H Subgroups 1, 2, 3, 9, 10, 11 NOTE: 1. Alternate Group A testing may be exercised in accordance with MIL-STD-883, Method 5005. TABLE 7. TOTAL DOSE IRRADIATION TEST CONFORMANCE GROUP Group E Subgroup 2 READ AND RECORD METHOD PRE RAD POST RAD PRE RAD POST RAD 5005 1, 7, 9 Table 4 1, 9 Table 4 (Note 1) NOTE: 1. Except FN test which will be performed 100% Go/No-Go. TABLE 8. BURN-IN TEST CONNECTIONS (+125oC < TA < 139oC) OSCILLATOR OPEN GROUND 1/2 VCC = 3V ±0.5V VCC = 6V ±0.5V 50kHz 25kHz 1, 3, 4, 7, 8, 10, 11, 13, 14, 17, 18 2, 5, 6, 9, 12, 15, 16, 19 20 - - 10 2, 5, 6, 9, 12, 15, 16, 19 1, 3, 4, 7, 8, 11, 13, 14, 17, 18, 20 - - 1, 10 2, 5, 6, 9, 12, 15, 16, 19 20 11 3, 4, 7, 8, 13, 14, 17, 18 STATIC BURN-IN 1 (Note 1) STATIC BURN-IN 2 (Note 1) DYNAMIC BURN-IN (Note 1) NOTE: 1. Each pin except VCC and GND will have a series resistor of 500Ω ±5%. TABLE 9. IRRADIATION TEST CONNECTIONS (TA = +25oC, ±5oC) FUNCTION Irradiation Circuit (Note 1) OPEN GROUND VCC = 5V ±0.5V 2, 5, 6, 9, 12, 15, 16, 19 10 1, 3, 4, 7, 8, 11, 13, 14, 17, 18, 20 NOTE: 1. Each pin except VCC and GND will have a series resistor of 47kΩ ±5%. Group E, Subgroup 2, sample size is 4 dice/wafer, 0 failures. Spec Number 5 518820 ACS374MS Intersil - Space Products MS Screening Wafer Lot Acceptance (All Lots) Method 5007 (Includes SEM) 100% Static Burn-In 2 Method 1015, 24 Hours at +125oC Min Radiation Verification (Each Wafer) Method 1019, 4 Samples/Wafer, 0 Rejects 100% Interim Electrical Test 2 (Note 1) 100% Nondestructive Bond Pull Method 2023 100% Dynamic Burn-In Method 1015, 240 Hours at +125oC or 180 Hours at +135oC 100% Internal Visual Inspection Method 2010 100% Interim Electrical Test 3 (Note 1) 100% Temperature Cycling Method 1010 Condition C (-65o to +150oC) 100% Final Electrical Test 100% Constant Acceleration 100% Radiographics Method 2012 (2 Views) 100% PIND Testing 100% External Visual Method 2009 100% External Visual Inspection Group A (All Tests) Method 5005 (Class S) 100% Serialization Group B (Optional) Method 5005 (Class S) (Note 2) 100% Initial Electrical Test Group D (Optional) Method 5005 (Class S) (Note 2) 100% Static Burn-In 1 Method 1015, 24 Hours at +125oC Min CSI and/or GSI (Optional) (Note 2) 100% Interim Electrical Test 1 (Note 1) Data Package Generation (Note 3) 100% Fine and Gross Seal Method 1014 NOTES: 1. Failures from interim electrical tests 1 and 2 are combined for determining PDA (PDA = 5% for subgroups 1, 7, 9 and delta failures combined, PDA = 3% for subgroup 7 failures). Interim electrical tests 3 PDA (PDA = 5% for subgroups 1, 7, 9 and delta failures combined, PDA = 3% for subgroup 7 failures). 2. These steps are optional, and should be listed on the purchase order if required. 3. Data Package Contents: Cover Sheet (P.O. Number, Customer Number, Lot Date Code, Intersil Number, Lot Number, Quantity). Certificate of Conformance (as found on shipper). Lot Serial Number Sheet (Good Unit(s) Serial Number and Lot Number). Variables Data (All Read, Record, and delta operations). Group A Attributes Data Summary. Wafer Lot Acceptance Report (Method 5007) to include reproductions of SEM photos. NOTE: SEM photos to include percent of step coverage. X-Ray Report and Film, including penetrometer measurements. GAMMA Radiation Report with initial shipment of devices from the same wafer lot; containing a Cover Page, Disposition, RAD Dose, Lot Number, Test Package, Spec Number(s), Test Equipment, etc. Irradiation Read and Record data will be on file at Intersil. Propagation Delay Timing Diagram and Load Circuit DUT VIH VS TEST POINT RL 500Ω CL 50pF INPUT VSS TPLH TPHL VOH VS OUTPUT AC VOLTAGE LEVELS VOL PARAMETER ACS UNITS VCC 4.50 V VIH 4.50 V VS 2.25 V VIL 0 V GND 0 V Spec Number 6 518820 ACS374MS Pulse Width, Setup, Hold Timing Diagram Positive Edge Trigger and AC Load Circuit INPUT VIH DUT TW TEST POINT RL 500Ω CL 50pF VS VIL TSU INPUT CP VIH TH TW PULSE WIDTH, SETUP, HOLD VOLTAGE LEVELS VS VIL PARAMETER VCC VIH VS VIL GND TH = HOLD TIME TSU = SETUP TIME TW = PULSE WIDTH ACS UNITS 4.50 4.50 2.25 0 0 V V V V V Three-State High Timing Diagram and Load Circuit DUT VIH VS INPUT RL 500Ω CL 50pF VSS TPZH TEST POINT TPHZ VOH VT OUTPUT VW VOZ PULSE WIDTH, SETUP, HOLD VOLTAGE LEVELS PARAMETER VCC VIH VS VT VW GND ACS UNITS 4.50 4.50 2.25 2.25 3.60 0 V V V V V V Three-State Low Timing Diagram and Load Circuit VCC VIH VS INPUT RL 500Ω VSS TPZL TPLZ VT OUTPUT TEST POINT DUT VOZ CL 50pF VW VOL PULSE WIDTH, SETUP, HOLD VOLTAGE LEVELS PARAMETER VCC VIH VS VT VW GND ACS UNITS 4.50 4.50 2.25 2.25 0.90 0 V V V V V V Spec Number 7 518820 ACS374MS Die Characteristics DIE DIMENSIONS: 102 mils x 102 mils 2,600mm x 2,600mm DIE ATTACH: Material: Silver Glass or JM 7000 after 7/1/95 WORST CASE CURRENT DENSITY: < 2.0 x 105A/cm2 METALLIZATION: Type: AlSiCu Metal 1 Thickness: 6.75kÅ (Min), 8.25kÅ (Max) Metal 2 Thickness: 9kÅ (Min), 11kÅ (Max) BOND PAD SIZE: > 4.3 mils x 4.3 mils > 110µm x 110µm GLASSIVATION: Type: SiO2 Thickness: 8kÅ ±1kÅ Metallization Mask Layout ACS374MS D0 (3) Q0 (2) OE (1) VCC (20) Q7 (19) D7 (18) D1 (4) (17) D6 Q1 (5) (16) Q6 NC NC NC NC Q2 (6) (15) Q5 D2 (7) (14) D5 (8) D3 (9) Q3 (10) GND (11) CP (12) Q4 (13) D4 All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com Spec Number 8 518820