MC100EPT26 3.3V 1:2 Fanout Differential LVPECL/LVDS to LVTTL Translator Description The MC100EPT26 is a 1:2 Fanout Differential LVPECL/LVDS to LVTTL translator. Because LVPECL (Positive ECL) or LVDS levels are used only +3.3 V and ground are required. The small outline 8-lead package and the 1:2 fanout design of the EPT26 makes it ideal for applications which require the low skew duplication of a signal in a tightly packed PC board. The VBB output allows the EPT26 to be used in a Single-Ended input mode. In this mode the VBB output is tied to the D0 input for a non-inverting buffer or the D0 input for an inverting buffer. If used, the VBB pin should be bypassed to ground with > 0.01ĂmF capacitor. For a Single-Ended direct connection, use an external voltage reference source such as a resistor divider. Do not use VBB for a Single-Ended direct connection or port to another device. Features • • • • • • • • www.onsemi.com 8 1 SOIC−8 NB TSSOP−8 DFN8 D SUFFIX DT SUFFIX MN SUFFIX CASE 751−07 CASE 948R−02 CASE 506AA MARKING DIAGRAMS* 8 1 1.4 ns Typical Propagation Delay Maximum Frequency = > 275 MHz Typical 8 1 8 KPT26 ALYW G 1 SOIC−8 NB The 100 Series Contains Temperature Compensation A L Y W M G Operating Range: VCC = 3.0 V to 3.6 V with GND = 0 V 24 mA TTL outputs Q Outputs Will Default LOW with Inputs Open or at VEE VBB Output These Devices are Pb-Free, Halogen Free and are RoHS Compliant KA26 ALYWG G 1 4 3W MG G TSSOP−8 DFN8 = Assembly Location = Wafer Lot = Year = Work Week = Date Code = Pb-Free Package (Note: Microdot may be in either location) *For additional marking information, refer to Application Note AND8002/D. ORDERING INFORMATION Package Shipping† MC100EPT26DG Device SOIC−8 NB (Pb-Free) 98 Units/Tube MC100EPT26DR2G SOIC−8 NB (Pb-Free) 2500 Tape & Reel MC100EPT26DTG TSSOP−8 (Pb-Free) 100 Tape & Reel MC100RPT26DTR2G TSSOP−8 (Pb-Free) 2500 Tape & Reel MC100EPT26MNR4G DFN8 (Pb-Free) 1000 Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. © Semiconductor Components Industries, LLC, 2016 August, 2016 − Rev. 17 1 Publication Order Number: MC100EPT26/D MC100EPT26 Table 1. PIN DESCRIPTION NC D 1 8 2 7 VCC Pin Q0 LVTTL D VBB 3 4 6 5 LVPECL Q1 Function Q0, Q1 LVTTL Outputs D0**, D1** Differential LVPECL Inputs Pair VCC Positive Supply VBB Output Reference Voltage GND Ground NC No Connect EP (DFN8 only) Thermal exposed pad must be connected to a sufficient thermal conduit. Electrically connect to the most negative supply (GND) or leave unconnected, floating open. GND ** Pins will default to VCC/2 when left open. (Top View) Figure 1. 8-Lead Pinout and Logic Diagram Table 2. ATTRIBUTES Characteristics Value Internal Input Pulldown Resistor 50 kW Internal Input Pullup Resistor 50 kW ESD Protection Human Body Model Machine Model Charged Device Model > 1.5 kV > 100 V > 2 kV Moisture Sensitivity, Indefinite Time Out of Drypack (Note 1) SOIC−8 NB TSSOP−8 DFN8 Flammability Rating Pb-Free Pkg Level 1 Level 3 Level 1 Oxygen Index: 28 to 34 Transistor Count UL 94 V−0 @ 0.125 in 117 Devices Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test 1. For additional information, see Application Note AND8003/D. www.onsemi.com 2 MC100EPT26 Table 3. MAXIMUM RATINGS Symbol Parameter Condition 1 Rating Unit 3.8 V 0 to 3.8 V ±0.5 mA Operating Temperature Range −40 to +85 °C Tstg Storage Temperature Range −65 to +150 °C qJA Thermal Resistance (Junction-to-Ambient) 0 lfpm 500 lfpm SOIC−8 NB SOIC−8 NB 190 130 °C/W qJC Thermal Resistance (Junction-to-Case) Standard Board SOIC−8 NB 41 to 44 °C/W qJA Thermal Resistance (Junction-to-Ambient) 0 lfpm 500 lfpm TSSOP−8 TSSOP−8 185 140 °C/W qJC Thermal Resistance (Junction-to-Case) Standard Board TSSOP−8 41 to 44 °C/W qJA Thermal Resistance (Junction-to-Ambient) 0 lfpm 500 lfpm DFN8 DFN8 129 84 °C/W Tsol Wave Solder (Pb-Free) 265 °C qJC Thermal Resistance (Junction-to-Case) 35 to 40 °C/W VCC Positive Power Supply GND = 0 V VIN Input Voltage GND = 0 V IBB VBB Sink/Source TA Condition 2 VI ≤ VCC (Note 1) DFN8 Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. JEDEC standard multilayer board − 2S2P (2 signal, 2 power) Table 4. PECL INPUT DC CHARACTERISTICS (VCC = 3.3 V; GND = 0.0 V (Note 1)) −40°C Symbol Characteristic Min Typ 25°C Max Min Typ 85°C Max Min Typ Max Unit VIH Input HIGH Voltage (Single-Ended) 2075 2420 2075 2420 2075 2420 mV VIL Input LOW Voltage (Single-Ended) 1355 1675 1355 1675 1355 1675 mV VBB Output Voltage Reference 1775 1975 1775 1975 1775 1975 V 3.3 1.2 3.3 1.2 3.3 V 150 mA VIHCMR Input HIGH Voltage Common Mode Range (Differential) (Note 2) IIH Input HIGH Current IIL Input LOW Current D D 1875 1.2 150 −150 −150 1875 150 −150 −150 −150 −150 1875 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 1. Input parameters vary 1:1 with VCC. 2. VIHCMR min varies 1:1 with GND, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. www.onsemi.com 3 MC100EPT26 Table 5. TTL OUTPUT DC CHARACTERISTICS (VCC = 3.3 V; GND = 0.0 V; TA = −40°C to 85°C) Symbol Characteristic Condition VOH Output HIGH Voltage IOH = −3.0 mA IOL = 24 mA Min Typ Max 2.4 Unit V VOL Output LOW Voltage 0.5 V ICCH Power Supply Current 10 25 35 mA ICCL Power Supply Current 15 34 40 mA IOS Output Short Circuit Current −50 −150 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. Table 6. AC CHARACTERISTICS (VCC = 3.0 V to 3.6 V; GND = 0.0 V (Note 1)) −40°C 25°C Characteristic Min Typ fmax Maximum Frequency (Figure 2) 275 350 tPLH, tPHL Propagation Delay to Output Differential (Note 2) 1.2 1.2 1.5 1.5 2.0 1.8 tSK+ + tSK− − tSKPP Within Device Skew + + Within Device Skew − − Device-to-Device Skew (Note 3) 15 20 100 tJITTER Random Clock Jitter (RMS) (Figure 2) @ ≤ 200 MHz @ > 200 MHz Symbol VPP tr tf Max 85°C Min Typ 275 350 Max Min Typ 275 350 1.2 1.2 1.5 1.5 2.0 1.8 60 85 500 15 20 100 6 20 30 275 Max 1.3 1.2 1.7 1.5 2.2 1.8 ns 60 85 500 20 30 100 85 85 500 ps 6 40 30 275 6 170 30 275 Input Voltage Swing (Differential Configuration) 150 800 1200 150 800 1200 150 800 1200 Output Rise/Fall Times (0.8 V−2.0 V) 330 600 950 330 600 950 330 650 950 Q, Q Unit MHz ps mV ps NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 1. Measured with a 750 mV 50% duty-cycle clock source. RL = 500 W to GND and CL = 20 pF to GND. Refer to Figure 3. 2. Reference (VCC = 3.3 V ± 5%; GND = 0 V) 3. Skews are measured between outputs under identical transitions. VOL 0.5 V VOH 8 VOH (V) 2.0 JITTER 4 1.0 0.0 0 100 200 FREQUENCY (MHz) Figure 2. Typical VOH / Jitter versus Frequency (255C) www.onsemi.com 4 0 300 RANDOM CLOCK JITTER (ps RMS) 12 3.0 MC100EPT26 APPLICATION TTL RECEIVER CHARACTERISTIC TEST *CL includes fixture capacitance CL * RL AC TEST LOAD GND Figure 3. TTL Output Loading Used for Device Evaluation Resource Reference of Application Notes AN1405/D − ECL Clock Distribution Techniques AN1406/D − Designing with PECL (ECL at +5.0 V) AN1503/D − ECLinPSt I/O SPiCE Modeling Kit AN1504/D − Metastability and the ECLinPS Family AN1568/D − Interfacing Between LVDS and ECL AN1672/D − The ECL Translator Guide AND8001/D − Odd Number Counters Design AND8002/D − Marking and Date Codes AND8020/D − Termination of ECL Logic Devices AND8066/D − Interfacing with ECLinPS AND8090/D − AC Characteristics of ECL Devices www.onsemi.com 5 MC100EPT26 PACKAGE DIMENSIONS SOIC−8 NB D SUFFIX CASE 751−07 ISSUE AK −X− NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751−01 THRU 751−06 ARE OBSOLETE. NEW STANDARD IS 751−07. A 8 5 S B 0.25 (0.010) M Y M 1 4 −Y− K G C N DIM A B C D G H J K M N S X 45 _ SEATING PLANE −Z− 0.10 (0.004) H D 0.25 (0.010) M Z Y S X M J S SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm Ǔ ǒinches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 6 MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 _ 8 _ 0.010 0.020 0.228 0.244 MC100EPT26 PACKAGE DIMENSIONS TSSOP−8 DT SUFFIX CASE 948R−02 ISSUE A 8x 0.15 (0.006) T U 0.10 (0.004) S 2X L/2 L 8 5 1 PIN 1 IDENT 0.15 (0.006) T U K REF M T U V S 0.25 (0.010) B −U− 4 M A −V− S NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 6. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. S F DETAIL E C 0.10 (0.004) −T− SEATING PLANE D −W− G DETAIL E www.onsemi.com 7 DIM A B C D F G K L M MILLIMETERS MIN MAX 2.90 3.10 2.90 3.10 0.80 1.10 0.05 0.15 0.40 0.70 0.65 BSC 0.25 0.40 4.90 BSC 0_ 6_ INCHES MIN MAX 0.114 0.122 0.114 0.122 0.031 0.043 0.002 0.006 0.016 0.028 0.026 BSC 0.010 0.016 0.193 BSC 0_ 6_ MC100EPT26 PACKAGE DIMENSIONS DFN8 2x2, 0.5 P MN SUFFIX CASE 506AA ISSUE F D PIN ONE REFERENCE 2X 0.10 C 2X A B L1 ÇÇ ÇÇ 0.10 C DETAIL A E OPTIONAL CONSTRUCTIONS ÉÉ ÉÉ ÇÇ EXPOSED Cu TOP VIEW A DETAIL B 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994 . 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.20 MM FROM TERMINAL TIP. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. L L DIM A A1 A3 b D D2 E E2 e K L L1 ÉÉ ÇÇ ÇÇ A3 MOLD CMPD A1 DETAIL B 0.08 C (A3) NOTE 4 SIDE VIEW ALTERNATE CONSTRUCTIONS A1 C MILLIMETERS MIN MAX 0.80 1.00 0.00 0.05 0.20 REF 0.20 0.30 2.00 BSC 1.10 1.30 2.00 BSC 0.70 0.90 0.50 BSC 0.30 REF 0.25 0.35 −−− 0.10 SEATING PLANE RECOMMENDED SOLDERING FOOTPRINT* DETAIL A D2 1 4 8X L E2 K 8 5 e/2 e 8X 1.30 PACKAGE OUTLINE 0.90 b 2.30 1 0.10 C A B 0.05 C 8X 0.50 8X 0.50 PITCH 0.30 NOTE 3 BOTTOM VIEW DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ECLinPS is a trademark of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 www.onsemi.com 8 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC100EPT26/D