RHOPOINT B40 4-channel rf relay Datasheet

B40 4-Channel RF Relays
Ball Grid Array 4-Channel Relays
The B40 is four independent form A channels in one quad package.
Coto’s Ball Grid Array (BGA) construction offers a breakthrough in
reed relay performance. This patented technology1 allows for shorter
RF paths in a controlled 50 Ω environment to minimize signal
attentuation. The designer is now able to switch or pass signals with
wider bandwidth and faster rise time than alternative technologies.
This is particularly important in Mixed Signal IC testers. This 4-in-one
BGA packaging allows relays to be integrated easily on boards designed
for surface mount processing.
Series Features
BGA Surface Mount
Ability to pass GHz signals
Rise time < 40ρSec
50Ω Characteristic Impedance
Low Capacitance
1
Patented Design
Top View
Top View
Applications
IC Testers
In-Line Relay Testers
Memory Testers
Mixed Signal Testers
High Bandpass Applications
Top View
Dimensions in Inches
(Millimeters)
Notes:
1
Protected by one or more of the following
US Patents: 6025768, 6052045, 6294971,
6683518, RE38381 and other foreign patents.
RHOPOINT COMPONENTS LTD Email: [email protected] Web: www.rhopointcomponents.com
B40 4-Channel RF Relays
Test Parameters
Coil Resistance
Nominal Voltage
Must Operate Voltage
Must Release Voltage
Coil Resistance
Nominal Voltage
Must Operate Voltage
Must Release Voltage
Switching Voltage
Switching Current
Carry Current (Continuous)
Contact Rating (Resistive Load)
3
Life Expectancy Signal Switching
3
Resistive Load
Other Load Conditions3
Static Contact Resistance (initial)
Dynamic Contact Resistance (initial)
Insulation Res
All Isolated Pins
Capacitance
Across Contacts
Capacitance
Open Contact to Coil
Capacitance
Closed Contact to Coil
Dielectric
Strength
1,2
Conditions
49.5
3.3V Coil
B40-0002
Magnetic Interaction5
0.4
149.4
5V Coil
B40-0003
Max DC/Peak AC
Switch and Shield
Resistive Load
1VDC / 10mA
12VDC / 10mA
Consult Factory
0.05VDC / 10mA
0.5V / 50mA 100 Hz, 1.5 mSec
100VDC
Shield Guarding
Shield Guarding
Shield Guarding
B40
Typ
Max
Units
55.0
3.3
60.5
4.0
2.4
166.0
5.0
182.6
6.0
3.8
Ω
Volts DC
Volts DC
Volts DC
Ω
Volts DC
Volts DC
Volts DC
Volts
Amps
Amps
Watts
6
x 10 Ops
x 106 Ops
0.4
125
0.25
0.5
3.0
1000
1
Ω
Ω
Ω
pF
pF
pF
0.125
0.150
10!10
10 12
0.2
0.3
0.5
100 µA
100 µA
100 µA
150
1000
1000
Nominal Voltage coil drive @ 30 Hz,
square wave
-3 dB roll-off frequency
Corrected for measurement
system response time
Between Adjacent Channels
100
30
Across Contacts
Contact to Coil
Contact To Shield
Operate Time
(including bounce)
Release Time
(Si diode damped)
4
RF Insertion Loss
Signal Rise Time (10% - 90%)
Min
V (DC/Pk AC)
V (DC/Pk AC)
V (DC/Pk AC)
200
50
40
µSec
µSec
GHz
pSec
16
%
11.0
NOTES:
1
All parameters specified per EIA/NARM
standards for dry reed relays, # RS-421 and
RS-436, if a suitable parametric standard exists.
2
Unless otherwise noted, all parameters are
specified at 25°C and 40% RH.
3
Life expectancies based on characteristic life
(63.2% failure) calculated from the 2-parameter
Weibull distribution. Contact resistance >2.0Ω
defines end of life.
4
Frequency at which the difference between output
and input signal amplitude exceeds -3dB. (Direct
wired using 50Ω coaxial cable.)
5
Maximum increase in operate voltage for any
channel when all channel coils are driven at
nominal coil voltage and with the same drive
polarity.
ENVIRONMENTAL RATINGS:
Storage Temperature: -35°C to +100°C.
Operating Temperature: -20°C to +85°C.
Vibration: sinusoidal vibration with an amplitude of
10G over a 10Hz to 2000Hz frequency range shall
not cause a closed channel activated at the nominal
coil voltage to open, not an open channel to close.
Max Soldering Temperature: 226°C (438°F) max for
1 minute dwell time. Temperature measured at a
relay ball termination.
RHOPOINT COMPONENTS LTD Email: [email protected] Web: www.rhopointcomponents.com
43
Similar pages