LP2980 Micropower 50 mA Ultra Low-Dropout Regulator General Description Features The LP2980 is a 50 mA, fixed-output voltage regulator designed specifically to meet the requirements of battery-powered applications. Using an optimized VIP™ (Vertically Integrated PNP) process, the LP2980 delivers unequaled performance in all specifications critical to battery-powered designs: Dropout Voltage. Typically 120 mV @ 50 mA load, and 7 mV @ 1 mA load. Ground Pin Current. Typically 375 µA @ 50 mA load, and 80 µA @ 1 mA load. Sleep Mode. Less than 1 µA quiescent current when ON/ OFF pin is pulled low. Smallest Possible Size. SOT-23 and micro SMD packages use an absolute minimum board space. Minimum Part Count. Requires only 1 µF of external capacitance on the regulator output. Precision Output. 0.5% tolerance output voltages available (A grade). 5.0V, 3.3V, and 3.0V versions available as standard products. n n n n n n n n n n n n n Ultra low dropout voltage Output voltage accuracy 0.5% (A Grade) Guaranteed 50 mA output current Smallest possible size (SOT-23, micro SMD package) Requires only 1 µF external capacitance < 1 µA quiescent current when shutdown Low ground pin current at all load currents High peak current capability (150 mA typical) Wide supply voltage range (16V max) Fast dynamic response to line and load Low ZOUT over wide frequency range Overtemperature/overcurrent protection −40˚C to +125˚C junction temperature range Applications n n n n Cellular Phone Palmtop/Laptop Computer Personal Digital Assistant (PDA) Camcorder, Personal Stereo, Camera Block Diagram DS012078-1 Connection Diagram and Ordering Information 5-Lead Small Outline Package (M5) micro SMD, 5 Bump Package (BPA05) DS012078-60 DS012078-3 Top View See NS Package Number MF05A For ordering information see Table 1 Bottom View See NS Package Number BPA05 VIP™ is a trademark of National Semiconductor Corporation. © 2000 National Semiconductor Corporation DS012078 www.national.com LP2980 Micropower 50 mA Ultra Low-Dropout Regulator April 2000 LP2980 Ordering Information TABLE 1. Package Marking and Order Information Output Voltage (V) Grade Order Information Package Marking Supplied as: 5-Lead Small Outline Package (M5) For output voltages ≤ 2V, refer to LP2980LV datasheet. If a non-standard voltage is required, see LP2980-ADJ. 2.5 A LP2980AIM5X-2.5 L0NA 3000 Units on Tape and Reel 2.5 A LP2980AIM5-2.5 L0NA 1000 Units on Tape and Reel 2.5 STD LP2980IM5X-2.5 L0NB 3000 Units on Tape and Reel 2.5 STD LP2980IM5-2.5 L0NB 1000 Units on Tape and Reel 2.6 A LP2980AIM5X-2.6 L48A 3000 Units on Tape and Reel 2.6 A LP2980AIM5-2.6 L48A 1000 Units on Tape and Reel 2.6 STD LP2980IM5X-2.6 L48B 3000 Units on Tape and Reel 2.6 STD LP2980IM5-2.6 L48B 1000 Units on Tape and Reel 2.7 A LP2980AIM5X-2.7 L26A 3000 Units on Tape and Reel 2.7 A LP2980AIM5-2.7 L26A 1000 Units on Tape and Reel 2.7 STD LP2980IM5X-2.7 L26B 3000 Units on Tape and Reel 2.7 STD LP2980IM5-2.7 L26B 1000 Units on Tape and Reel 2.8 A LP2980AIM5X-2.8 L13A 3000 Units on Tape and Reel 2.8 A LP2980AIM5-2.8 L13A 1000 Units on Tape and Reel 2.8 STD LP2980IM5X-2.8 L13B 3000 Units on Tape and Reel 2.8 STD LP2980IM5-2.8 L13B 1000 Units on Tape and Reel 2.9 A LP2980AIM5X-2.9 L12A 3000 Units on Tape and Reel 2.9 A LP2980AIM5-2.9 L12A 1000 Units on Tape and Reel 2.9 STD LP2980IM5X-2.9 L12B 3000 Units on Tape and Reel 2.9 STD LP2980IM5-2.9 L12B 1000 Units on Tape and Reel 3.0 A LP2980AIM5X-3.0 L02A 3000 Units on Tape and Reel 3.0 A LP2980AIM5-3.0 L02A 1000 Units on Tape and Reel 3.0 STD LP2980IM5X-3.0 L02B 3000 Units on Tape and Reel 3.0 STD LP2980IM5-3.0 L02B 1000 Units on Tape and Reel 3.1 A LP2980AIM5X-3.1 L30A 3000 Units on Tape and Reel 3.1 A LP2980AIM5-3.1 L30A 1000 Units on Tape and Reel 3.1 STD LP2980IM5X-3.1 L30B 3000 Units on Tape and Reel 3.1 STD LP2980IM5-3.1 L30B 1000 Units on Tape and Reel 3.2 A LP2980AIM5X-3.2 L31A 3000 Units on Tape and Reel 3.2 A LP2980AIM5-3.2 L31A 1000 Units on Tape and Reel 3.2 STD LP2980IM5X-3.2 L31B 3000 Units on Tape and Reel 3.2 STD LP2980IM5-3.2 L31B 1000 Units on Tape and Reel 3.3 A LP2980AIM5X-3.3 L00A 3000 Units on Tape and Reel 3.3 A LP2980AIM5-3.3 L00A 1000 Units on Tape and Reel 3.3 STD LP2980IM5X-3.3 L00B 3000 Units on Tape and Reel 3.3 STD LP2980IM5-3.3 L00B 1000 Units on Tape and Reel 3.5 A LP2980AIM5X-3.5 L27A 3000 Units on Tape and Reel 3.5 A LP2980AIM5-3.5 L27A 1000 Units on Tape and Reel 3.5 STD LP2980IM5X-3.5 L27B 3000 Units on Tape and Reel 3.5 STD LP2980IM5-3.5 L27B 1000 Units on Tape and Reel 3.6 A LP2980AIM5X-3.6 L28A 3000 Units on Tape and Reel 3.6 A LP2980AIM5-3.6 L28A 1000 Units on Tape and Reel 3.6 STD LP2980IM5X-3.6 L28B 3000 Units on Tape and Reel 3.6 STD LP2980IM5-3.6 L28B 1000 Units on Tape and Reel www.national.com 2 LP2980 Ordering Information (Continued) TABLE 1. Package Marking and Order Information (Continued) Output Voltage (V) Grade Order Information Package Marking Supplied as: For output voltages ≤ 2V, refer to LP2980LV datasheet. If a non-standard voltage is required, see LP2980-ADJ. 3.8 A LP2980AIM5X-3.8 L21A 3000 Units on Tape and Reel 3.8 A LP2980AIM5-3.8 L21A 1000 Units on Tape and Reel 3.8 STD LP2980IM5X-3.8 L21B 3000 Units on Tape and Reel 3.8 STD LP2980IM5-3.8 L21B 1000 Units on Tape and Reel 4.0 A LP2980AIM5X-4.0 L25A 3000 Units on Tape and Reel 4.0 A LP2980AIM5-4.0 L25A 1000 Units on Tape and Reel 4.0 STD LP2980IM5X-4.0 L25B 3000 Units on Tape and Reel 4.0 STD LP2980IM5-4.0 L25B 1000 Units on Tape and Reel 4.5 A LP2980AIM5X-4.5 L0XA 3000 Units on Tape and Reel 4.5 A LP2980AIM5-4.5 L0XA 1000 Units on Tape and Reel 4.5 STD LP2980IM5X-4.5 L0XB 3000 Units on Tape and Reel 4.5 STD LP2980IM5-4.5 L0XB 1000 Units on Tape and Reel 4.7 A LP2980AIM5X-4.7 L37A 3000 Units on Tape and Reel 4.7 A LP2980AIM5-4.7 L37A 1000 Units on Tape and Reel 4.7 STD LP2980IM5X-4.7 L37B 3000 Units on Tape and Reel 4.7 STD LP2980IM5-4.7 L37B 1000 Units on Tape and Reel 5.0 A LP2980AIM5X-5.0 L01A 3000 Units on Tape and Reel 5.0 A LP2980AIM5-5.0 L01A 1000 Units on Tape and Reel 5.0 STD LP2980IM5X-5.0 L01B 3000 Units on Tape and Reel 5.0 STD LP2980IM5-5.0 L01B 1000 Units on Tape and Reel micro SMD, 5 Bump Package (BPA05) 3.3 A LP2980AIBP-3.3 250 Units on Tape and Reel 3.3 A LP2980AIBPX-3.3 3000 Units on Tape and Reel 3.3 STD LP2980IBP-3.3 250 Units on Tape and Reel 3.3 STD LP2980IBPX-3.3 3000 Units on Tape and Reel 5.0 A LP2980AIBP-5.0 250 Units on Tape and Reel 5.0 A LP2980AIBPX-5.0 3000 Units on Tape and Reel 5.0 STD LP2980IBP-5.0 250 Units on Tape and Reel 5.0 STD LP2980IBPX-5.0 3000 Units on Tape and Reel 3 www.national.com LP2980 Absolute Maximum Ratings (Note 1) ESD Rating (Note 2) Power Dissipation (Note 3) Input Supply Voltage (Survival) Input Supply Voltage (Operating) Shutdown Input Voltage (Survival) Output Voltage (Survival), (Note 4) IOUT (Survival) Input-Output Voltage (Survival), (Note 5) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Storage Temperature Range Operating Junction Temperature Range Lead Temperature (Soldering, 5 sec.) −65˚C to +150˚C −40˚C to +125˚C 260˚C 2 kV Internally Limited −0.3V to +16V 2.1V to +16V −0.3V to +16V −0.3V to +9V Short Circuit Protected −0.3V to +16V Electrical Characteristics Limits in standard typeface are for TJ = 25˚C, and limits in boldface type apply over the full operating temperature range. Unless otherwise specified: VIN = VO(NOM) + 1V, IL = 1 mA, COUT = 1 µF, VON/OFF = 2V. Symbol ∆VO Parameter Output Voltage Tolerance Conditions Typ LP2980AI-XX LP2980I-XX (Note 6) (Note 6) Min Max Min Max IL = 1 mA −0.50 0.50 −1.0 1.0 1 mA < IL < 50 mA −0.75 0.75 −1.5 1.5 2.5 −3.5 −2.5 VIN–VO Output Voltage VO(NOM) + 1V Line Regulation ≤ VIN ≤ 16V Dropout Voltage 0.007 IL = 0 1 (Note 7) IGND Ground Pin Current IL = 1 mA 7 IL = 10 mA 40 IL = 50 mA 120 IL = 0 65 IL = 1 mA 80 IL = 10 mA 140 IL = 50 mA 375 VON/OFF < 0.18V VON/OFF 0 %VNOM 3.5 0.014 0.014 0.032 0.032 3 3 5 5 10 10 15 15 60 60 90 90 150 150 225 225 95 95 125 125 110 110 170 170 220 220 460 460 600 600 1200 1200 1 1 mV µA ON/OFF Input Voltage High = O/P ON 1.4 Low = O/P OFF 0.55 0.18 0.18 ION/OFF ON/OFF Input Current VON/OFF = 0 0 −1 −1 IO(PK) Peak Output Current VOUT ≥ VO(NOM) − 5% 150 en Output Noise BW = 300 Hz–50 kHz, 160 µV Voltage (RMS) COUT = 10 µF 63 dB 150 mA Ripple Rejection 5 f = 1 kHz 1.6 %/V (Note 8) VON/OFF = 5V 1.6 Units 15 100 V µA 15 100 mA COUT = 10 µF IO(MAX) Short Circuit Current RL = 0 (Steady State) (Note 9) Note 1: Absolute maximum ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when operating the device outside of its rated operating conditions. Note 2: The ESD rating of pins 3 and 4 is 1 kV. www.national.com 4 (Continued) Note 3: The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal resistance, θJA, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperature is calculated using: The value of θJA for the SOT-23 package is 220˚C/W and the micro SMD package is 320˚C/W. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Note 4: If used in a dual-supply system where the regulator load is returned to a negative supply, the LP2980 output must be diode-clamped to ground. Note 5: The output PNP structure contains a diode between the VIN and VOUT terminals that is normally reverse-biased. Reversing the polarity from VIN to VOUT will turn on this diode (see Application Hints). Note 6: Limits are 100% production tested at 25˚C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control (SQC) methods. The limits are used to calculate National’s Average Outgoing Quality Level (AOQL). Note 7: Dropout voltage is defined as the input to output differential at which the output voltage drops 100 mV below the value measured with a 1V differential. Note 8: The ON/OFF inputs must be properly driven to prevent misoperation. For details, refer to Application Hints. Note 9: See Typical Performance Characteristics curves. Basic Application Circuit DS012078-2 *ON/OFF input must be actively terminated. Tie to VIN if this function is not to be used. **Minimum Output Capacitance is 1 µF to insure stability over full load current range. More capacitance provides superior dynamic performance and additional stability margin (see Application Hints). ***Do not make connections to this pin. 5 www.national.com LP2980 Electrical Characteristics LP2980 Typical Performance Characteristics Unless otherwise specified: TA = 25˚C, VIN = VO(NOM) + 1V, COUT = 2.2 µF, all voltage options, ON/OFF pin tied to VIN. Output Voltage vs Temperature Output Voltage vs Temperature DS012078-9 Output Voltage vs Temperature DS012078-39 Dropout Characteristics DS012078-16 DS012078-40 Dropout Characteristics Dropout Characteristics DS012078-14 DS012078-15 www.national.com 6 Unless otherwise specified: TA = 25˚C, VIN = VO(NOM) + 1V, COUT = 2.2 µF, all voltage options, ON/OFF pin tied to VIN. (Continued) Dropout Voltage vs Temperature Dropout Voltage vs Load Current DS012078-11 Ground Pin Current vs Temperature DS012078-20 Ground Pin Current vs Load Current DS012078-19 DS012078-10 Input Current vs VIN Input Current vs VIN DS012078-18 DS012078-17 7 www.national.com LP2980 Typical Performance Characteristics LP2980 Typical Performance Characteristics Unless otherwise specified: TA = 25˚C, VIN = VO(NOM) + 1V, COUT = 2.2 µF, all voltage options, ON/OFF pin tied to VIN. (Continued) Line Transient Response Line Transient Response DS012078-21 Load Transient Response DS012078-22 Load Transient Response DS012078-41 Load Transient Response DS012078-42 Load Transient Response DS012078-23 www.national.com DS012078-24 8 Unless otherwise specified: TA = 25˚C, VIN = VO(NOM) + 1V, COUT = 2.2 µF, all voltage options, ON/OFF pin tied to VIN. (Continued) Short Circuit Current Instantaneous Short Circuit Current vs Temperature DS012078-32 DS012078-12 Short Circuit Current Instantaneous Short Circuit Current vs Output Voltage DS012078-33 DS012078-43 Output Impedance vs Frequency Output Impedance vs Frequency DS012078-44 DS012078-26 9 www.national.com LP2980 Typical Performance Characteristics LP2980 Typical Performance Characteristics Unless otherwise specified: TA = 25˚C, VIN = VO(NOM) + 1V, COUT = 2.2 µF, all voltage options, ON/OFF pin tied to VIN. (Continued) Output Noise Density Ripple Rejection DS012078-25 DS012078-27 Input to Output Leakage vs Temperature Output Reverse Leakage vs Temperature DS012078-28 Turn-On Waveform DS012078-29 Turn-Off Waveform DS012078-30 www.national.com DS012078-31 10 Unless otherwise specified: TA = 25˚C, VIN = VO(NOM) + 1V, COUT = 2.2 µF, all voltage options, ON/OFF pin tied to VIN. (Continued) ON/OFF Pin Current vs VON/OFF DS012078-45 11 www.national.com LP2980 Typical Performance Characteristics LP2980 times have ESR values lower than the minimum required by the LP2980, and relatively large capacitance change with temperature. The manufacturer’s datasheet for the capacitor should be consulted before selecting a value. Application Hints OUTPUT CAPACITOR Like any low-dropout regulator, the LP2980 requires an output capacitor to maintain regulator loop stability. This capacitor must be selected to meet the requirements of minimum capacitance and equivalent series resistance (ESR) range. It is not difficult to find capacitors which meet the criteria of the LP2980, as the acceptable capacitance and ESR ranges are wider than for most other LDOs. In general, the capacitor value must be at least 1 µF (over the actual ambient operating temperature), and the ESR must be within the range indicated in Figures 1, 2 and Figure 3. It should be noted that, although a maximum ESR is shown in these Figures, it is very unlikely to find a capacitor with ESR that high. Tantalum Capacitors Surface-mountable solid tantalum capacitors offer a good combination of small physical size for the capacitance value, and ESR in the range needed by the LP2980. The results of testing the LP2980 stability with surface-mount solid tantalum capacitors show good stability with values of at least 1 µF. The value can be increased to 2.2 µF (or more) for even better performance, including transient response and noise. Small value tantalum capacitors that have been verified as suitable for use with the LP2980 are shown in Table 2. Capacitance values can be increased without limit. Aluminum Electrolytic Capacitors Although probably not a good choice for a production design, because of relatively large physical size, an aluminum electrolytic capacitor can be used in the design prototype for an LP2980 regulator. A value of at least 1 µF should be used, and the ESR must meet the conditions of Figures 1, 2 and Figure 3. If the operating temperature drops below 0˚C, the regulator may not remain stable, as the ESR of the aluminum electrolytic capacitor will increase, and may exceed the limits indicated in the Figures. Test results of LP2980 stability using multilayer ceramic capacitors show that a minimum value of 2.2 µF is usually needed for the 5V regulator. For the lower output voltages, or for better performance, a higher value should be used, such as 4.7 µF. Multilayer ceramic capacitors that have been verified as suitable for use with the LP2980 are shown in Table 3. TABLE 3. Surface-Mount Multilayer Ceramic Capacitor Selection Guide 2.2 µF Surface-Mount Ceramic Manufacturer Tokin Part Number 1E225ZY5U-C203 Murata GRM42-6Y5V225Z16 4.7 µF Surface-Mount Ceramic Manufacturer Tokin Part Number 1E475ZY5U-C304 DS012078-48 FIGURE 1. 1 µF ESR Range TABLE 2. Surface-Mount Tantalum Capacitor Selection Guide 1 µF Surface-Mount Tantalums Manufacturer Part Number Kemet T491A105M010AS NEC NRU105M10 Siemens B45196-E3105-K Nichicon F931C105MA Sprague 293D105X0016A2T 2.2 µF Surface-Mount Tantalums Manufacturer Part Number Kemet T491A225M010AS NEC NRU225M06 Siemens B45196/2.2/10/10 Nichicon F930J225MA Sprague 293D225X0010A2T DS012078-49 FIGURE 2. 2.2 µF ESR Range Multilayer Ceramic Capacitors Surface-mountable multilayer ceramic capacitors may be an attractive choice because of their relatively small physical size and excellent RF characteristics. However, they some- www.national.com 12 Technology (SMT) Assembly Considerations, it should be noted that the pad style which must be used with the 5-pin package is the NSMD (non-solder mask defined) type. (Continued) For best results during assembly, alignment ordinals on the PC board may be used to facilitate placement of the micro SMD device. Micro SMD Light Sensitivity Exposing the micro SMD device to direct sunlight will cause misoperation of the device. Light sources such as Halogen lamps can also affect electrical performance if brought near to the device. The wavelenghts which have the most detrimental effect are reds and infra-reds, which means that the fluorescent lighting used inside most buildings has very little effect on performance. A micro SMD test board was brought to within 1 cm of a fluorescent desk lamp and the effect on the regulated output voltage was negligible, showing a deviation of less than 0.1% from nominal. DS012078-50 FIGURE 3. 10 µF ESR Range REVERSE CURRENT PATH The power transistor used in the LP2980 has an inherent diode connected between the regulator input and output (see below). DS012078-34 FIGURE 4. LP2980 Reverse Current Path If the output is forced above the input by more than a VBE, this diode will become forward biased and current will flow from the VOUT terminal to VIN. No damage to the LP2980 will occur under these conditions as long as the current flowing into the output pin does not exceed 100 mA. ON/OFF INPUT OPERATION The LP2980 is shut off by pulling the ON/OFF input low, and turned on by driving the input high. If this feature is not to be used, the ON/OFF input should be tied to VIN to keep the regulator on at all times (the ON/OFF input must not be left floating). To ensure proper operation, the signal source used to drive the ON/OFF input must be able to swing above and below the specified turn-on/turn-off voltage thresholds which guarantee an ON or OFF state (see Electrical Characteristics). The ON/OFF signal may come from either a totem-pole output, or an open-collector output with pull-up resistor to the LP2980 input voltage or another logic supply. The high-level voltage may exceed the LP2980 input voltage, but must remain within the Absolute Maximum Ratings for the ON/OFF pin. It is also important that the turn-on/turn-off voltage signals applied to the ON/OFF input have a slew rate which is greater than 40 mV/µs. Important: the regulator shutdown function will operate incorrectly if a slow-moving signal is applied to the ON/OFF input. Micro SMD Mounting The micro SMD package requires specific mounting techniques which are detailed in National Semiconductor Application Note # 1112. Referring to the section Surface Mount 13 www.national.com LP2980 Application Hints LP2980 Typical Applications DS012078-51 FIGURE 5. 5V/400mA Regulator Assuming a maximum allowable junction temperature of 150˚C for the MPS2907A device, the following curves show the maximum VIN and IL values that may be safely used for several ambient temperatures. The LP2980 can be used to control higher-current regulators, by adding an external PNP pass device. With the PNP transistors shown in , the output current can be as high as 400 mA, as long as the input voltage is held within the Safe Operation Boundary Curves shown below in. To ensure regulation, the minimum input voltage of this regulator is 6V. This “headroom” is the sum of the VBE of the external transistor and the dropout voltage of the LP2980. Notes: A. Drive this input with a logic signal (see Application Hints). If the shutdown function is not to be used, tie the ON/OFF pin directly to the VIN pin. B. Recommended devices (other PNP transistors can be used if the current gain and voltage ratings are similar). C. Capacitor is required for regulator stability. Minimum size is shown, and may be increased without limit. D. Increasing the output capacitance improves transient response and increases phase margin. E. Maximum safe input voltage and load current are limited by power dissipation in the PNP pass transistor and the maximum ambient temperature for the specific application. If a TO-92 transistor such as the MPS2907A is used, the thermal resistance from junction-to-ambient is 180˚C/W in still air. DS012078-52 FIGURE 6. Safe Operation Boundary Curves for Figure 5 DS012078-53 FIGURE 7. 5V to 3.3V @ 3A Converter below. For best load regulation at the high load current, the LP2980 output voltage connection should be made as close to the load as possible. Although this regulator can handle a much higher load current than can the LP2980 alone, it can be shut down in the same manner as the LP2980. When the ON/OFF control is With limited input voltage range, the LP2980 can control a 3.3V, 3A regulator with the use of a high current-gain external PNP pass transistorias shown in . If the regulator is to be loaded with the full 3A, heat sinking will be required on the pass transistor to keep it within its rated temperature range. Refer to the Heatsink Thermal Resistance Requirements, www.national.com 14 tachment thermal resistance is assumed to be 1.5˚C/W. All calculations are for 5.5V input voltage (which is worst-case for power dissipation). (Continued) brought low, the converter will be in shutdown, and will draw less than 1 µA from the source. Notes: A. Drive this input with a logic signal (see Application Hints). If the shutdown function is not to be used, tie the ON/OFF pin directly to the VIN pin. B. Capacitor is required for regulator stability. Minimum size is shown, and may be increased without limit. C. Increasing the output capacitance improves transient response and increases phase margin. D. A heatsink may be required for this transistor. The maximum allowable value for thermal resistance of the heatsink is dependent on ambient temperature and load current (see curves in ). Once the value is obtained from the graph, a heatsink must be selected which has a thermal resistance equal to or lower than this value. If the value is above 60˚C/W, no heatsink is required (the TO-220 package alone will safely dissipate this). For these curves, a maximum junction temperature of 150˚C is assumed for the pass transistor. The case-to-heatsink at- DS012078-54 FIGURE 8. Heatsink Thermal Resistance Requirements for Figure 7 15 www.national.com LP2980 Typical Applications LP2980 Physical Dimensions inches (millimeters) unless otherwise noted 5-Lead Small Outline Package (M5) NS Package Number MA05B For Order Numbers, refer to Table 1 in the “Order Information” section of this document. www.national.com 16 LP2980 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) NOTES: UNLESS OTHERWISE SPECIFIED 1. EPOXY COATING 2. 63Sn/37Pb EUTECTIC BUMP 3. RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD. 4. PIN 1 IS ESTABLISHED BY LOWER LEFT CORNER WITH RESPECT TO TEXT ORIENTATION. REMAINING PINS ARE NUMBERED COUNTER CLOCKWISE. 5. XXX IN DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE X1 IS PACKAGE WIDTH, X2 IS PACKAGE LENGTH AND X3 IS PACKAGE HEIGHT. 6.NO JEDEC REGISTRATION AS OF AUG.1999. micro SMD, 5 Bump Package (BPA05) NS Package Number BPA05A For Order Numbers, refer to Table 1 in the “Order Information” section of this document. The dimensions for X1, X2 and X3 are as given: X1 = 0.930 +/− 0.030mm X2 = 1.107 +/− 0.030mm X3 = 0.850 +/− 0.050mm 17 www.national.com LP2980 Micropower 50 mA Ultra Low-Dropout Regulator Notes LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: [email protected] www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: [email protected] National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.