LP2967 Dual Micropower 150 mA Low-Dropout Regulator in micro SMD Package General Description Features The LP2967 is a 150 mA, dual fixed-output voltage regulator designed to provide ultra low-dropout and low noise in battery powered applications. n n n n n n n n n n n n Using an optimized VIP (Vertically Integrated PNP) process, the LP2967 delivers unequalled performance in all specifications critical to battery powered designs: Dropout Voltage: Typically 240 mV at 150 mA load, and 6 mV at 1 mA load for each output. Ground Pin Current: Typically 1 mA at 150 mA load, and 200 µA at 1 mA load for each output. Enhanced Stability: The LP2967 is stable with output capacitor ESR as low as 5 mΩ, which allows the use of ceramic capacitors on the output. Sleep Mode: Less than 2 µA quiescent current when SD pins are pulled low. Smallest Possible Size: micro SMD package uses absolute minimum board space. Precision Output: 1.25% tolerance. Ultra low drop-out voltage Guaranteed 150mA output current, 300 mA peak Smallest possible size (micro SMD package) Requires minimum external components Stable with 2.2 µF tantalum or ceramic capacitor Output voltage accuracy ± 1% < 2 µA quiescent current when shut down Wide supply voltage range (16V max.) Low ZOUT: 0.3Ω typical (10 Hz to 1 MHz) Over temperature/over current protection −40˚C to +125˚C junction temperature range Custom voltages available Applications n n n n Cellular Phone Palmtop/Laptop Computer Personal Digital Assistance (PDA) Camcorder, Personal Stereo and Camera Low Noise: By adding a 100 nF bypass capacitor, output noise can be reduced to 30 µV (typical). Multiple voltage options, from 1.8V to 5.0V, are available. Consult factory for custom voltages. Block Diagram 10114201 © 2003 National Semiconductor Corporation DS101142 www.national.com LP2967 Dual Micropower 150 mA Low-Dropout Regulator in micro SMD Package April 2003 LP2967 Basic Application Circuit 10114202 *SD1 and SD2 must be actively terminated. Tie them to VIN if their functions are not needed. **Minimum capacitance are shown to ensure stability (may be increased without limit). *** Reduces output noise (may be omitted if application is not noise critical). Use ceramic or film type with very low leakage current. Ordering Information Output Voltage (V) VOUT1 VOUT2 Grade Order Information Package Marking Supplied As For MSOP Package 2.5 2.8 STD LP2967IMM-2528 LCAB 1000 Units Tape and Reel 2.5 2.8 STD LP2967IMMX-2528 LCAB 3000 Units Tape and Reel 2.5 3.3 STD LP2967IMM-2533 LCBB 1000 Units Tape and Reel 2.5 3.3 STD LP2967IMMX-2533 LCBB 3000 Units Tape and Reel 2.6 2.6 STD LP2967IMM-2626 LCLB 1000 Units Tape and Reel 2.6 2.6 STD LP2967IMMX-2626 LCLB 3000 Units Tape and Reel 2.8 2.8 STD LP2967IMM-2828 LAQB 1000 Units Tape and Reel 2.8 2.8 STD LP2967IMMX-2828 LAQB 3000 Units Tape and Reel 2.8 3.3 STD LP2967IMM-2833 LCCB 1000 Units Tape and Reel 2.8 3.3 STD LP2967IMMX-2833 LCCB 3000 Units Tape and Reel L0P 1000 Units Tape and Reel For 8-Bump micro SMD Package (BPA08) 1.8 2.5 STD LP2967IBP-1825 1.8 2.5 STD LP2967IBPX-1825 L0P 3500 Units Tape and Reel 1.8 3.3 STD LP2967IBP-1833 L0R 1000 Units Tape and Reel 1.8 3.3 STD LP2967IBPX-1833 L0R 3500 Units Tape and Reel 2.5 2.8 STD LP2967IBP-2528 CA 1000 Units Tape and Reel 2.5 2.8 STD LP2967IBPX-2528 CA 3500 Units Tape and Reel 2.5 3.3 STD LP2967IBP-2533 CB 1000 Units Tape and Reel 2.5 3.3 STD LP2967IBPX-2533 CB 3500 Units Tape and Reel 2.6 2.6 STD LP2967IBP-2626 CL 1000 Units Tape and Reel 2.6 2.6 STD LP2967IBPX-2626 CL 3500 Units Tape and Reel 2.8 2.8 STD LP2967IBP-2828 AQ 1000 Units Tape and Reel 2.8 2.8 STD LP2967IBPX-2828 AQ 3500 Units Tape and Reel www.national.com 2 Output Voltage (V) VOUT1 VOUT2 LP2967 Ordering Information (Continued) Grade Order Information Package Marking Supplied As 2.8 3.3 STD LP2967IBP-2833 CC 1000 Units Tape and Reel 2.8 3.3 STD LP2967IBPX-2833 CC 3500 Units Tape and Reel 10114205 10114206 3 www.national.com LP2967 Package Outline and Connection Diagram 10114204 Top View Mini SO-8 Package 8-Lead Small Outline Integrated Circuit (SOIC) Package Code: MM 10114203 Top View micro SMD 8-Bump micro SMD Package Code: BP Pin Description Name Pin Number Function micro SMD MSOP VOUT2 A1 7 Output voltage of the second LDO SD2 B1 6 Shutdown input for the second LDO BYPASS C1 5 Bypass capacitor for the bandgap GND C2 - Ground Substrate GND C3 4 Common Ground SD1 B3 3 Shutdown input for the first LDO VOUT 1 A3 2 Output voltage of the first LDO VIN A2 1, 8 www.national.com Common input voltage for both LDOs 4 (Note 1) ESD Rating (Note 2) 1.5kV If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Input Supply Voltage (Survival) Storage Temperature Range Output Voltage (Survival) (Note 4) −65˚C to +150˚C 2.1V to +16V Shutdown Input Voltage (Survival) −0.3V to +16V Lead Temp. ( IR reflow, 10 sec.) 245˚C IOUT (Survival) Pad Temp. (IR reflow, 10 sec.) 245˚C Input-Output Voltage (Survival), (Note 5) Operating Junction Temp. Range −40˚C to +125˚C Power Dissipation (Note 4) Internally Limited −0.3V to +16V Input Supply Voltage (Operating) Short Circuit Protected −0.3V to + 16V Electrical Characteristics Limits in standard typeface are for Tj = 25˚C, and limits in boldface type apply over the full operating junction temperature range. Unless otherwise specified, VIN = VO(NOM) + 1V, IL = 1mA, CIN = 1µF,COUT = 4.7µF, VON/OFF = 1.6V. Symbol Parameter Conditions Min Typ Max Units 1.25 3.0 % Operating Specifications VO Output Voltage Tolerance ILOAD = 1mA 1mA < ILOAD < 150 mA ∆VO/∆VIN Line Regulation VO(NOM) + 1V < VIN < 16V ∆VO/∆ILOAD Load Regulation VIN = VO(NOM) + 1V (Note 6) 1mA < ILOAD < 150 mA −5 ILOAD = 1mA 6 10 15 ILOAD = 50mA 100 125 180 ILOAD = 150mA 240 290 425 Both Regulators ON ILOAD (1 and 2) = 1mA 200 300 (VIN - VO) Min. Dropout Voltage (Note 7) −1.25 −3.0 0.08 %/V mV/V mV Operating Currents IQ Quiescent Current ILOAD (1 and 2) = 150mA 1700 5000 One Regulator OFF ILOAD (1 and 2) = 1mA 180 250 ILOAD (1 and 2) = 150mA 1000 2500 Both Regulators OFF (Shutdown) IPEAK Peak Output Current µA 2 VO < VOUT(NOM) − 5% 200 450 mA 1.6 1.4 V Control Inputs (SD1, SD2) VIN (H) Regulator ON Control Input Voltage VIN (L) Regulator OFF Control Input Voltage VO < VOUT(NOM) − 5% ION/OFF Control Input Current V(SD) = 0V V(SD) = 5V 0.300 0.8 V −2 7 µA Dynamic Characteristics en Output Noise Voltage CBYPASS = 100nF, 300 to 100kHz 5 30 µV rms www.national.com LP2967 Absolute Maximum Ratings LP2967 Electrical Characteristics (Continued) Limits in standard typeface are for Tj = 25˚C, and limits in boldface type apply over the full operating junction temperature range. Unless otherwise specified, VIN = VO(NOM) + 1V, IL = 1mA, CIN = 1µF,COUT = 4.7µF, VON/OFF = 1.6V. Symbol Parameter Conditions Min Typ Max Units CBYPASS = 100nF, VIN = VO(NOM) + 1V + 100mV p-p square wave (trise and tfall = 100ns) RR Ripple Rejection F F F F F F F = = = = = = = −52 −54 −56 −58 −50 −47 −70 120Hz 800Hz 1000Hz 1600Hz 10kHz 100kHz 1MHz dB ∆ILOAD 1 = 150 mA at 1kHz rate (15 mA/µs rise and fall slope) ILOAD2 = 1mA Xtalk Crosstalk Rejection ∆VOUT 2/ ∆VOUT 1 −100 ∆ILOAD 2 = 150 mA at 1KHz rate (15 mA/µs rise and fall slope) ILOAD 1 = 1mA ∆VOUT 2/ ∆VOUT 1 dB −100 Note 1: Absolute maximum ratings indicate limits beyond which damage to the device may occur. Electrical specifications do not apply when operating the device beyond its rated operating conditions. Note 2: Rating is for the human body mode, a 100pF capacitor discharged through a 1.5kΩ resistor into each pin. Note 3: The maximum allowable power dissipation is calculated by using PDMAX = (TJMAX - TA/θJA, where TJMAX is the maximum junction temperature, TA is the ambient temperature, and θJA is the junction-to-ambient thermal resistance of the specified package. Therefore, the maximum power dissipation must be derated at elevated temperatures and is limited by TJMAX, θJA and A. Note 4: If used in a dual-supply system where the regulator load is returned to a negative supply, the LP2967 output must be diode-clamped to ground. Note 5: The output PNP structure contains a diode between the VIN and VOUT terminals that is normally reverse-biased. Reversing the polarity from VIN and VOUT will turn on this diode. Note 6: Load regulation excursion over temperature is included in Output Voltage Tolerance. Note 7: The dropout voltage of a regulator is defined as the minimum input-to-output differential required to stay within 100mV of the output voltage measured with a 1V differential. www.national.com 6 OFF Unless otherwise specified: CIN = 1µF, COUT = 4.7µF, VON/ = 1.6V, IL = 1mA, TA = 25˚C. Output Voltage vs Temperature Output Voltage vs Temperature 10114255 10114256 Output Voltage vs Temperature Dropout Voltage vs Load 10114216 10114257 Dropout Voltage vs Temp. and Load Ground Pin Current vs Temp. and Load 10114217 10114218 7 www.national.com LP2967 Typical performance Characteristics LP2967 Typical performance Characteristics Unless otherwise specified: CIN = 1µF, COUT = 4.7µF, VON/OFF = 1.6V, IL = 1mA, TA = 25˚C. (Continued) Cross Channel Isolation IOUT1 = IOUT2 = 1 mA Cross Channel Isolation IOUT1 = IOUT2 = 150 mA 10114212 10114211 Input Current vs VIN Input Current vs VIN (VOUT = 3.3V) 10114213 10114214 Input Current vs VIN (VOUT = 2.5V) Shutdown Current vs Shutdown Voltage 10114215 www.national.com 10114220 8 = 1.6V, IL = 1mA, TA = 25˚C. (Continued) Short Circuit Current vs VOUT Short Circuit Current vs Time 10114259 10114258 Short Circuit Current Line Transient Reponse 10114260 10114222 Line Transient Reponse Line Transient Reponse 10114223 10114224 9 www.national.com LP2967 Typical performance Characteristics Unless otherwise specified: CIN = 1µF, COUT = 4.7µF, VON/OFF LP2967 Typical performance Characteristics Unless otherwise specified: CIN = 1µF, COUT = 4.7µF, VON/OFF = 1.6V, IL = 1mA, TA = 25˚C. (Continued) Load Transient Reponse (VOUT1) Load Transient Reponse (VOUT1) 10114231 10114232 Load Transient Reponse (VOUT1) Load Transient Reponse (VOUT2) 10114234 10114233 Load Transient Reponse (VOUT2) Load Transient Reponse (VOUT2) 10114235 www.national.com 10114236 10 = 1.6V, IL = 1mA, TA = 25˚C. (Continued) LP2967-2.5V Turn-On Time (2nd Output OFF) LP2967-2.5V Turn-On Time (2nd Output ON) 10114240 10114241 Output Impedance vs Frequency Ripple Rejection vs Frequency 10114248 10114249 Ripple Rejection vs Frequency Ripple Rejection vs Frequency 10114250 10114251 11 www.national.com LP2967 Typical performance Characteristics Unless otherwise specified: CIN = 1µF, COUT = 4.7µF, VON/OFF LP2967 Typical performance Characteristics Unless otherwise specified: CIN = 1µF, COUT = 4.7µF, VON/OFF = 1.6V, IL = 1mA, TA = 25˚C. (Continued) Ripple Rejection vs Frequency Ripple Rejection vs Frequency 10114252 10114253 Ripple Rejection vs Frequency Output Noise Density 10114262 10114254 Output Noise Density 10114261 www.national.com 12 LP2967-3.3V Region of Stability with 4.7 µF COUT EXTERNAL CAPACITORS The LP2967 low dropout regulator requires two external capacitors, CIN and COUT to assure the device’s output stability. CBYPASS may be used to reduce output noise. The capacitors must be correctly selected with respect to capacitance values for all three capacitors and ESR value for COUT. Input Capacitor An input capacitor with a minimum capacitance value of 1µF is required between the LP2967 input and ground (the amount of capacitance may be increased without limit). This capacitor must be located a distance of not more than 0.5 inches from the input pin and returned to a clean analog ground. Any good quality ceramic or tantalum may be used for this capacitor. 10114207 LP2967-2.5V Region Of Stability with 10 µF COUT Output Capacitor The output capacitor must meet the requirement for minimum capacitance value of 2.2 µF and also have an appropriate ESR (equivalent series resistance) value. The LP2967 is actually designed to work with ceramic or tantalum output capacitors, utilizing circuitry which allows the regulator to be stable with an output capacitor whose ESR is as low as 4 mΩ. It may also be possible to use a film capacitor at the output, but this type is not as attractive for reasons of size and cost. Important: The output capacitor must maintain its ESR in the stable region over the full operating temperature range of the application to assure stability. The minimum required amount of output capacitance is 2.2 µF. Output capacitor size can be increased without limit. It is important to remember that capacitor tolerance and variation with temperature must be taken into consideration when selecting an output capacitor so that the minimum required amount of output capacitance is provided over the full operating temperature range. 10114209 LP2967-2.5V Region Of Stability with 4.7 µF COUT LP2967-3.3V Region of Stability with 10 µF COUT 10114210 10114208 13 www.national.com LP2967 Application Hints LP2967 Application Hints ceramic capacitors is that their capacitance can vary with temperature. Most large value ceramic capacitors are manufactured with the Z5U or Y5V temperature characteristic, which results in the capacitance dropping by more than 50% as the temperature goes from 25˚C to 85˚C. This could cause problems if a 2.2 µF capacitor were used on the output since it will drop down to approximately 1 µF at high ambient temperatures. This could cause the LP2967 to oscillate. If Z5U or Y5V capacitors are used on the output, a minimum capacitance value of 4.7 µF must be used. (Continued) LP2967-2.5V Region Of Stability with 2.2 µF COUT A better choice for temperature coefficient in ceramic capacitors is X7R or X5R which hold the capacitance to within ± 15% over the full temperature range. Unfortunately, the larger values of capacitance are not offered by all manufacturers in the X7R dielectric. Tantalum For the LP2967, tantalum capacitors are less desirable than ceramic for use as output capacitors because they are typically more expensive when comparing equivalent capacitance and voltage ratings in the 2.2 µF to 4.7 µF range of capacitance. Tantalum capacitors have good temperature stability: a 4.7µF was tested and showed a 10% decline in capacitance as the temperature was decreased from +125˚C to −40˚C while the ESR increased by about 2:1 over the same range of temperatures. This increase in ESR at lower temperatures can cause oscillations when marginal quality capacitors are used and the upper limit for ESR value is exceeded. 10114265 No-Load Operation If a 2.2 µF output capacitor is used, the minimum stable ESR value rises to about 0.5 Ω at load currents below 1 mA. If the minimum output load is < 1 mA (with COUT = 2.2 µF), a Tantalum output capacitor should be used (the ESR of a ceramic will be too low). It should be noted that if a 4.7 µF (or larger) output capacitor is used, the part is fully stable with either Tantalum or ceramic from no load to full load output current. Aluminum The large physical size of aluminum electrolytic capacitors make them unattractive for use with the LP2967. Their ESR characteristics are also not well suited to the requirements of LDO regulators. The ESR of an aluminum electrolytic is higher than that of a tantalum, and it also varies greatly with temperature. A typical aluminum electrolytic can exhibit an ESR increase of 50X when going from 20˚C to −40˚C. Also, some aluminum electrolytic capacitors can not be used below −25˚C because the electrolyte will freeze. Bypass Capacitor Connecting a 10 nF capacitor to the Bypass pin significantly reduces noise on the regulator output. It should be noted that the capacitor is connected directly to a high impedance circuit in the bandgap reference. Because this circuit has only a few microamperes flowing into it, any significant loading on this node will cause a change in the regulated output voltage. For this reason, DC leakage current through the noise bypass capacitor must never exceed 100 nA, and should be kept as low as possible for best output voltage accuracy. The types of capacitors best suited for the noise bypass capacitor are ceramic and film capacitors. High quality ceramic capacitors with either NPO or COG dielectric typically have very low leakage. 10 nF polypropylene and polycarbonate film capacitors are available in small surface mount packages and typically have extremely low leakage current. SHUTDOWN OPERATION The two LDO regulators in the LP2967 have independent shutdown pins. A low logic level signal at either of the shutdown pins SD1 or SD2 will turn off the corresponding regulator output VOUT1 or VOUT2. Pins SD1 and SD2 must be terminated by tying them to VIN for a proper operation when the shutdown function is not required. CAPACITOR CHARACTERISTICS REVERSE CURRENT PATH The internal power transistor in the LP2967 has an inherent parasitic diode. During normal operation, the input voltage is higher than the output voltage and the parasitic diode is reverse biased. However, if the output is pulled above the input in an application, then current flows from the output to the input if the parasitic diode gets forward biased. The output can be pulled above the input as long as the current in the parasitic diode is limited to 150mA. Ceramic Ceramic capacitors have the lowest ESR values, which make them best for eliminating high frequency noise. The outputs of LP2967 require a minimum of 2.2 µF of capacitance. The ESR of a typical 2.2 µF ceramic capacitor is in the range of 4 mΩ to 20 mΩ, which easily meets the ESR limits required for stability by the LP2967. One disadvantage of www.national.com 14 ambient temperature coefficient (θJA) for an MSOP-8 package is 235˚C/W and the 8-bump micro SMD with minimum copper area is 220˚C/W. The total power dissipation of the device is given by: PD = (VIN − VOUT1) IOUT1 + (VIN − VOUT2) IOUT2 (Continued) MAXIMUM POWER DISSAIPATION CAPABILITY Each output pin the LP2967 can deliver a current of up to 150mA over the full operating junction temperature range. However, the maximum output current must be derated at higher ambient temperature to ensure the junction temperature does not exceed 125˚C. Under all possible conditions, the junction temperatures must be within the range specified under operating conditions. The LP2967 is available in MSOP-8 package and 8-bump micro SMD. The junction to The maximum power dissipation, PDmax, that the device can tolerate can be calculated by using the formula: PDmax = (TJMAX − TA) / θJA where TJMAX is the maximum specified junction temperature (125˚C), and TA is the maximum ambient temperature. 15 www.national.com LP2967 Application Hints LP2967 Physical Dimensions inches (millimeters) unless otherwise noted micro SMD Package NS Package Number BPA08F5B The dimensions of X1, X2, and X3 are given below: X1 = 1.412mm X2 = 1.946mm X3 = 0.850mm www.national.com 16 inches (millimeters) unless otherwise noted (Continued) Mini SO-8 Package Type MM For Ordering, Refer to Ordering Information Table NS Package Number MUA08A LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. LP2967 Dual Micropower 150 mA Low-Dropout Regulator in micro SMD Package Physical Dimensions