K-Band Doppler Sensor Module RF Frequency: 24.05 to 24.25 GHz Model No. NJR4262 Specifications Rev.00-02 February 26, 2013 Copyright 2013 New Japan Radio Co., Ltd. Microwave Components Division -Notice of Proprietary InformationThis document and its contents are proprietary to New Japan Radio Co., Ltd. This publication and its contents may not be reproduced or distributed for any other purpose without the written permission of New Japan Radio Co., Ltd. 1 Rev.00-02_Feb.27,2013_ NJR4262 Caution 1. NJRC strives to produce reliable and high quality microwave components. NJRC's microwave components are intended for specific applications and require proper maintenance and handling. To enhance the performance and service of NJRC's microwave components, the devices, machinery or equipment into which they are integrated should undergo preventative maintenance and inspection at regularly scheduled intervals. Failure to properly maintain equipment and machinery incorporating these products can result in catastrophic system failures. 2. To ensure the highest levels of reliability, NJRC products must always be properly handled. The introduction of external contaminants (e.g. dust, oil or cosmetics) can result in failures of microwave components. 3. NJRC offers a variety of microwave components intended for particular applications. It is important that you select the proper component for your intended application. You may contact NJRC's sales office or sales representatives, if you are uncertain about the products listed in the catalog and the specification sheets. 4. Special care is required in designing devices, machinery or equipment, which demand high levels of reliability. This is particularly important when designing critical components or systems whose foreseeable failure can result in situations that could adversely affect health or safety. In designing such critical devices, equipment or machinery, careful consideration should be given to, amongst other things, their safety design, fail-safe design, back-up and redundancy systems, and diffusion design. 5. The products listed in the catalog and specification sheets may not be appropriate for use in certain equipment where reliability is critical or where the products may be subjected to extreme conditions. You should consult our sales office or sales representatives before using the products in any of the following types of equipment. * Aerospace Equipment * Equipment Used in the Deep Sea * Power Generator Control Equipment (nuclear, steam, hydraulic) * Life Maintenance Medical Equipment * Fire Alarm/Intruder Detector * Vehicle Control Equipment (automobile, airplane, railroad, ship, etc.) * Various Safety Equipment 6. NJRC's products have been designed and tested to function within controlled environmental conditions. Do not use products under conditions that deviate from methods or applications specified in the catalog and specification sheets. Failure to employ NJRC's products in the proper applications can lead to deterioration, destruction or failure of the products. NJRC shall not be responsible for any bodily injury, fires or accidents, property damage or any consequential damages resulting from the misuse or misapplication of its products. PRODUCTS ARE SOLD WITHOUT WARRANTY OF ANY OF KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. 7. The product specifications and descriptions listed in the catalog and specification sheets are subject to change at any time, without notice. * Above Specifications are subject to change without notice. 2 Rev.00-02_Feb.27,2013_ NJR4262 Category: K-Band Doppler Sensor Module Type Name: NJR4262 Description: Motion detector using microwave doppler effect Miniaturized RF circuit with MMIC technology High accurate I-Q mixer Specification: 1. Electric Characteristics (Common measure condition Ta= +25 deg.C) Specification Item Min. Typ. Max. Unit 3.3 5.5 V 1.1 Operation voltage 45 55 mA 1.2 Operation current 24.05 24.25 GHz 1.3 Operation frequency 1.4 E.I.R.P. +16 +20 dBm (40) (100) (mW) -1 0 MHz/deg.C 1.5 Frequency Stability 1.6 Start-up time 4 6 msec 1.7 2nd Harmonics (E.I.R.P.) -30 dBm 1.8 Radiation pattern 1.8.1 1.8.2 1.8.3 –3dB beam width (H-plane) –3dB beam width (V-plane) Side lobe suppression (H-plane) 1.8.4 Side lobe suppression (V-plane) 1.9 Noise Voltage - 70 28 - - deg. deg. dB - 13 - dB - - 400 mV 1.10 Signal level 0.5 0.8 - Vp-p 1.11 1.12 1.13 Fig.1: Offset voltage I-Q Amplitude Balance I-Q Phase Balance Typical Radiation Pattern 1.1 -3 85 1.35 - 1.6 +3 95 V dB deg. H-plane 70 deg. (±35 deg.) V-Plane -30 0 -90 Ta= -20 to +60 deg.C See Fig.1: Typical Radiation Pattern. No side lobe Upon amplified with 85dB Gain amp. Band width: 10 to 300Hz Refer to Fig.2 : Signal Test System V-plane 28 deg. (±14 deg.) Angle(deg.) 30 -30 60 -60 H-Plane Condition / Note -20 -10 0 (dBm) 0 Angle(deg.) 30 -60 90 -90 10 20 60 -20 -10 0 (dBm) 90 10 20 * Above Specifications are subject to change without notice. 3 Rev.00-02_Feb.27,2013_ NJR4262 2. Mechanical characteristics Item 2.1 Size 2.2 Weight 2.3 Interface / Pin assignment Specification 25(W) x 25(D) x 7.3(H) mm Tolerance: ±0.5 mm 7 g max. Pin Size: 0.64 mm square Pin Pitch: 2.54 mm Pin IF-I GND IF-Q VCC NC Description Doppler signal output(I). Output impedance:1.5kohm GND Doppler signal output(Q). Output impedance:1.5kohm Voltage supply. No connection. Recommended via hole diameter: 1.2 ± 0.05 mm 3. Environmental characteristics Item 3.1 Operation Temperature 3.2 Storage Temperature 3.3 Humidity 3.4 Vibration 3.5 Shock 4. Absolute Maximum Rating Item 4.1 Supply voltage 4.2 Operation Temperature 4.3 Storage Temperature Specification -20 to +60 deg.C -40 to +80 deg.C 0 to 95 % @ +30 deg.C 49.03 m/s2 (5 G) 30 to 50 Hz, 10 minutes, XYZ direction 196.13 m/s2 (20 G) Half sine, 11 msec, XYZ direction, 3 times Specification Min. Typ. Max. 0 7 -40 +85 -40 +85 Unit V deg.C deg.C Condition / Note No damage * Above Specifications are subject to change without notice. 4 Rev.00-02_Feb.27,2013_ NJR4262 5. Outline Unit : mm Tolance : ±0.3 * Above Specifications are subject to change without notice. 5 Rev.00-02_Feb.27,2013_ NJR4262 Fig2. Signal Test System DUT 29 dB Oscilloscope 14.6 to 24.6cm stroke 7cm Corner reflector RCS = 0.49m 2 Linear stage * Above Specifications are subject to change without notice. 6 Rev.00-02_Feb.27,2013_ NJR4262