Optically Coupled Isolator OPI110, OPI113, OPI1264 Series Features: • • • • 10 kV electrical isolation Choice of phototransistor or photodarington output Low-cost plastic housing UL recognized File No. E58730* Product Photo Here Description: Each Optoisolator in this data sheet contains an infrared Light Emitting Diode (LED) and a NPN silicon Photosensor. The OPI110 and OPI1264 devices have 890 nm Light Emitting Diode (LED) and NPN phototransistor sensor, whereas the OP113 has a 890 nm LED and a photodarlington sensor. The devices are sealed in a precast opaque housing with a optically transmissive path between the LED and the photosensor. The Optoisolators in this data sheet are UL approved under E 58730. This series is designed for transmission of information between one power supply voltage and another where the potentials during surge conditions are not greater than the guaranteed isolation voltage. Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for more information. Applications: • • • • • High voltage isolation between input and output Electrical isolation in dirty environments Industrial equipment Medical equipment Office equipment Ordering Information Part Number LED Peak Wavelength Sensor Isolation Voltage (,000) CTR Min / Max OPI110A 25 / NA 10 / 40 Transistor OPI110B 50 / 125 OPI110C 100 / NA 890 nm Photodarlington OPI1264 10 50 / NA 5 / 40 30 0.50" / 0.55" 12.5 / NA OPI1264A 25 / NA Transistor RoHS Lead Length / Spacing 12.5 / NA OPI110 OPI113 VCE IF (mA) (Volts) Typ / Max Max 10 / 40 OPI1264B 50 / 125 OPI1264C 100 / NA OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A 05/07 Page 1 of 3 Optically Coupled Isolator OPI110, OPI113, OPI1264 Series Absolute Maximum Ratings (TA = 25o C unless otherwise noted) Storage Temperature(1)(2) -40° C to +100° C Operating Temperature -40° C to +85° C Input-to-Output Isolation Voltage ± 10 kVDC (3) Lead Soldering Temperature (1/16” (1.6 mm) from case for 5 seconds with soldering iron) 260° C Input Diode Forward DC Current(4) 40 mA Reverse DC Voltage Power Dissipation 2V (5) 50 mW Output Photosensor Collector-Emitter Voltage OPI110, OPI1264 OPI113 30 15 Emitter-Collector Voltage 5 Power Dissipation (6) 100 mW Notes: (1) Measured with input and output leads shorted. Typical input/output capacitance is 0.06 pF. (2) UL recognition is for 3500 VAC for one minute. (3) RMA flux is recommended. The duration can be extended to 10 seconds maximum when flow soldering. (4) Derate linearly 0.67 mA/°C above 25°C. (5) Derate linearly 0.83 mA/°C above 25°C. (6) Derate linearly 1.67 mA/°C above 25°C. OPI110 OPI1264 OPI113 1 4 2 3 1 2 4 1 4 2 3 3 DIMENSIONS ARE IN: [MILLIMETERS] INCHES OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A 05/07 Page 2 of 3 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Optically Coupled Isolator OPI110, OPI113, OPI1264 Series Electrical Characteristics (TA = 25o C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Input Diode (See OP265 for additional information - for reference only) VF Forward Voltage - - 1.6 V IF = 20 mA IR Reverse Current - - 100 µA VR = 2 V Output Photosensor (See OP505 for additional information - for reference only) V(BR)CEO Collector-Emitter Breakdown Voltage OPI110, OPI1264 OPI113 30 15 - - V(BR)ECO Emitter-Collector Breakdown Voltage OPI110, OPI113 OPI1264 5 - - - V IE = 100 µA, IF = 0 IE = 100 µA Collector-Emitter Dark Current OPI110, OPI1264 OPI113 - - 100 100 nA VCE = 15 V, EE = 0 VCE = 10 V, EE = 0 12.5 25.0 50.0 100. 0 50.0 400 125 - Collector Saturation Voltage OPI110, OPI1264 OPI113 - - 0.4 1.2 V IF = 10 mA, IC = 1.6 mA IF = 10 mA, IC = 5 mA ICEO Collector-Emitter Dark Current OPI110, OPI1264 OPI113 - - 200 100 nA VCE = 20 V, IF = 0 VCE = 10 V, IF = 0 VISO Isolation Voltage 10 - - kVDC ICEO V IC = 100 µA IC = 100 µA, IF = 0 Coupled IC/IF VCE(SAT) DC Current Transfer Ratio OPI110, OPI1264 OPI110A, OPI1264A OPI110B, OPI1264B OPI110C, OPI1264C OPI113 % IF = 10 mA, VCE = 5 V IF = 10 mA, VCE = 5 V IF = 10 mA, VCE = 5 V IF = 10 mA, VCE = 5 V IF = 5 mA, VCE = 2 V See Note 1. Notes: (1) Measured with input and output leads shorted. Typical input/output capacitance is 0.06 pF. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A 05/07 Page 3 of 3