NKK M2022S1G40 General specification Datasheet

Electrical Capacity (Resistive Load)
Power Level (silver): 6A @ 125V AC & 3A @ 250V AC
4A @ 30V DC for On-None-On & On-None-Off; 3A @ 30V DC for all other circuits
Logic Level (gold): 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Logic/Power Level (gold over silver): Combines silver & gold ratings
Note: Find additional explanation of dual rating & operating range in Supplement section.
Other Ratings
Toggle:
Bushing:
Case:
Movable Contactor:
Movable Contacts:
Stationary Contacts:
Terminals:
Slides
Rotaries
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Angle of Throw:
Tactiles
Miniature Toggles
General Specifications
Programmable Illuminated PB
A
Keylocks
Pushbuttons
Rockers
Toggles
Series M
Materials & Finishes
Environmental Data
Operating Temp Range:
Humidity:
Vibration:
Shock:
Sealing:
10 milliohms maximum for silver; 20 milliohms maximum for gold
1,000 megohms minimum @ 500V DC
1,000V AC minimum between contacts for 1 minute minimum;
1,500V AC minimum between contacts and case for 1 minute minimum
100,000 operations minimum; 50,000 operations minimum for flat, locking & splashproof devices
25,000 operations minimum for silver; 50,000 operations minimum for gold;
50,000 operations minimum for silver at 3A @ 125V AC
25°
Brass with chrome plating
Frame: Stainless steel
Brass with nickel plating
Support Bracket: Brass with tin plating
Diallyl phthalate resin (UL94V–0)
Phosphor bronze with silver or gold plating
Silver alloy (code W); copper with gold plating (code G); or silver alloy with gold plating (code A)
Silver with silver plating (code W); copper or brass with gold plating (code G);
or silver with gold plating (code A)
Copper or brass with silver plating; or copper or brass with gold plating
–30°C through +85°C (–22°F through +185°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Splashproof bushing options B3, D3, D8, L3, & L8, which have o-rings inside & outside the
bushing, meet IP67 of IEC60529 Standards.
Tilt
Installation
Mounting Torque: 3.0Nm (26.55 lb•in) double nut for large bushing;
1.5Nm (13 lb•in) double nut & 0.7Nm (6 lb•in) single nut for all other bushings
Supplement
Accessories
Indicators
Touch
Processing
Soldering:
Cleaning:
Wave Soldering (PC version) for Gold: See Profile A in Supplement section.
Manual Soldering for Gold: See Profile A in Supplement section.
Wave Soldering (PC version) for Silver: See Profile B in Supplement section.
Manual Soldering for Silver: See Profile B in Supplement section.
Note: Lever must be in OFF (center) position while soldering.
These devices are not process sealed. Hand clean locally using alcohol based solution.
Standards & Certifications
Flammability Standards: UL94V–0 for case
UL: File No. E44145 - Recognized only when ordered with marking on switch.
Add “/U” or “/CUL” before dash in part number to order UL recognized switch.
All models recognized at 6A @ 125V AC, 3A @ 250V AC or 0.4VA maximum @ 28V DC maximum.
CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch.
Add “/C” before dash in part number to order CSA certified switch.
All models certified at 6A @ 125V AC or 3A @ 250V AC or 0.4VA maximum @ 28V maximum.
A48
www.nkk.com
Distinctive Characteristics
Rockers
A
Toggles
Series M
Miniature Toggles
Pushbuttons
Antirotation design, standard on noncylindrical levers, mates toggle
and bushing; bottom of toggle has two flatted sides which fit into
a complementary opening inside bushing.
Programmable Illuminated PB
Antijamming design protects contacts from damage due
to excessive downward force on actuator.
High torque bushing construction prevents rotation
or separation from frame during installation.
High insulating barriers increase isolation of
circuits in multipole devices and provide
added protection to contact points.
Keylocks
Molded diallyl phthalate case has a UL
flammability rating of 94V-0.
Rotaries
Epoxy sealed terminals prevent entry
of solder flux and other contaminants.
Slides
Prominent external insulating barriers
increase insulation resistance and
dielectric strength.
Tactiles
Interlocked actuator block, lever, and interior guide
prevent switch failure due to biased lever movement.
Actual Size
Page A48
Bracket PC Mount
Page A60
Angle PC Mount
Page A66
www.nkk.com
A49
Supplement
Accessories
Indicators
Bushing Mount
Touch
Tilt
Clinching of frame to case well above base and terminals
provides 1,500V dielectric strength.
A
TYPICAL SWITCH ORDERING EXAMPLE
S2
A2
G
Small Bushings
Contact Materials & Ratings
40
SPDT
S
.413” (10.5mm) Bat
A2
.280” (7.1mm) Smooth with Keyway
2
DPDT
SP3T
S2
.200” (5.08mm) Bat
S2
.350” (8.9mm) Smooth with Keyway
3
3PDT
S3
.256” (6.5mm) Bat
A1
.280” (7.1mm) Threaded with Keyway
E
.450” (11.4mm) Flatted
S1
.350” (8.9mm) Threaded with Keyway
*4
4PDT
DP3T
E2
.256” (6.5mm) Flatted
W
Silver; Rated
6A @ 125V AC & 3A @ 250V AC
G
Gold; Rated
0.4VA max @ 28V AC/DC max
A
Gold over Silver; Rated
6A @ 125V AC & 0.4VA max @
28V AC/DC max
Toggle dimensions are based on use with
a .350” (8.9mm) bushing; add .070”
(1.78mm) to toggle length when combining with a .280” (7.1mm) bushing.
* 4-pole available
ON
NONE
ON
3
ON
OFF
ON
5
ON
NONE
(ON)
8
(ON)
OFF
(ON)
9
ON
OFF
(ON)
*4
ON
ON
ON
*6
(ON)
ON
(ON)
*7
ON
ON
(ON)
L
.201” (5.1mm) Dia. Locking Lever
( ) = Momentary
Smooth with Keyway for Lever Lock
Conical Cap for S Bat Toggle
B
White
C
Red
E
Yellow
F
Green
G
Blue
Nickel Plated Supplied
with Switch
A
Black
C
Red
G
Blue
Terminals
30
.150” (3.81mm)
Right Angle PC (1-3 Pole)
32
Right Angle PCB
(1 Pole & 0.4VA Rating Only)
40
.150” (3.81mm)
Vertical PC (1-4 Pole)
45
.100” (2.54mm)
Vertical PC (1-4 Pole)
Standard Toggle, Bushing, & Terminal Combinations:
* 3-ON circuits available
S2A2G30, S2A2G40, SS2G30, SS2G40,
LL2G30, & LL2G40
with double and
four pole bases only
Touch
L2
C
Slides
2
Bushing For Locking Levers
Black
Tactiles
Locking Lever
A
Tilt
Tilt
Tactiles
Slides
Circuits
For S Bat Toggle
No
Code
Rotaries
on vertical
models only.
Cap Colors
B
Cap for Locking Lever
Programmable Illuminated PB
1
Optional Caps
Keylocks
Small Toggles
Rotaries
Keylocks
Poles
Touch
Programmable Illuminated PB
Pushbuttons
2
Pushbuttons
1
Rockers
M20
Toggles
Angle PC Mount Miniature Toggles
A
Rockers
Toggles
Series M
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
Supplement
Accessories
Switches are supplied without UL,
cULus & CSA marking unless specified.
UL, cULus & CSA recognized only when
ordered with marking on the switch.
Specific models, ratings, & ordering instructions are noted on General Specifications page.
A1
www.nkk.com
Indicators
Gold Contacts
with 0.4VA Rating
.280” (7.1mm)
Smooth Bushing with Keyway
Vertical PC Terminals with
.150” (3.81mm) Terminal Spacing
.200” (5.08mm) Bat Toggle
Accessories
IMPORTANT:
SPDT
ON-NONE-ON Circuit
Supplement
Indicators
M2012S2A2G40
www.nkk.com
A1
Toggles
Series M
A
POLES & CIRCUITS
Programmable Illuminated PB
Keylocks
Toggle Position
) = Momentary
Down
Pole
Pushbuttons
Rockers
(
Model
Center
Connected Terminals
Up
Down
Keyway
Throw & Schematics
Center
Up
Note: Terminal numbers are not actually on
the switch.
* Reverse circuits available for vertical
mount SP & DP upon request.
Keyway
M2012
M2013
M2015
* M2018
M2019
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
2-3
OPEN
2-1
SPDT
M2022
* M2023
M2025
* M2028
M2029
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
2-3 5-6
OPEN
2-1 5-4
DPDT
3P
M2032
M2033
M2035
M2038
M2039
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
2-3 5-6
8-9
OPEN
2-1 5-4
8-7
3PDT
4P
M2042
M2043
M2045
M2048
M2049
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
2-3 5-6
8-9 11-12
OPEN
2-1 5-4
8-7 11-10
4PDT
*
SP
DP
Slides
Rotaries
Angle PC Mount Miniature Toggles
2 (COM)
3
1
2
(COM)
3
1
2
3
5
5
3
1
2
5
1
6
(COM)
6
4
(COM)
8
9
7
8
11
9
4
6
4
7
12
10
For 3 Throw (3-On)
Tilt
Tactiles
Connected Terminals & Schematics
Pole Model Down Center
SP
M2024 ON
M2026 (ON)
M2027 ON
ON
ON
ON
Up
ON
(ON)
(ON)
Down
Center
External
Connection
2 (in)
5
External
Connection
2 (in)
5
1 (out)
3 4 (out) 6 (out)
1 (out)
Supplement
Accessories
Indicators
Touch
2-3 5-6
DP
M2044 ON
M2046 (ON)
M2047 ON
ON
ON
ON
ON
(ON)
(ON)
External
Connection
2 (in)
5
1 (out) 3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out)
External connection must be
made during field installation.
A68
External
Conn
6
3
5
2
4
1
(out)
3 4 (out) 6 (out)
External
Connection
2 (in)
5
External
Connection
8 (in)
11
1 (out)
(out)
2-1 5-4
1 (out) 3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out)
2-3 5-4
8-9 11-10
External connection must be
made during field installation.
www.nkk.com
External
Connection
8 (in)
11
External
Connection
2 (in)
5
3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out)
Common
(in)
3 4 (out) 6 (out)
1 (out)
External
Connection
8 (in)
11
The DP3T model utilizes a
four pole base.
(out)
External
Connection
2 (in)
5
2-3 5-4
2-3 5-6
8-9 11-12
The SP3T model utilizes a
double pole base.
Up
2-1 5-4
8-7 11-10
(out)
External
Conn
Common
(in)
(out)
(out)
12
9
11
8
5
2
10
7
4
1
(out)
6
3
(out)
Common
(in)
(out)
A
SMALL TOGGLES
.200” (5.08mm)
Bat
S2
25°
(2.8) Dia
.110
.256” (6.5mm)
Bat
E
(5.08)
.200
.450” (11.4mm)
Flatted
(5.08)
.200
25°
.256” (6.5mm)
Flatted
E2
25°
(2.54)
.100
(2.7) Dia
.106
(4.2)
.165
(11.4)
.450
(6.5)
.256
25°
(2.7) Dia
.106
(10.5)
.413
Rockers
.413” (10.5mm)
Bat
Pushbuttons
S3
S
Programmable Illuminated PB
Important:
Toggle length changes based on
bushing selected. All illustrations are
shown with .350” (8.9mm) long
bushing. When using a .280” (7.1mm)
long bushing, toggle length increases
.070” (1.78mm).
(2.5)
.098
25°
(6.5)
.256
Keylocks
Standard Material & Finish: Brass with Bright Chrome
Contact factory for optional finishes.
SMALL BUSHINGS
S2
(0.8)
.031
.350” (8.9mm)
Smooth with Keyway
(0.8)
.031
(6.2) Dia
.244
(6.2) Dia
.244
(2.5)
.098
(2.5)
.098
(0.9)
.035
(7.1)
.280
(8.0) Dia
.315
Rotaries
.280” (7.1mm)
Smooth with Keyway
Slides
A2
(0.9)
.035
(8.9)
.350
(8.0) Dia
.315
Tactiles
When using this bushing, toggle length
is increased by .070” (1.78mm).
.280” (7.1mm)
Threaded with Keyway
S1
.350” (8.9mm)
Threaded with Keyway
Tilt
A1
Toggles
Series M
Angle PC Mount Miniature Toggles
(0.8)
.031
1/4-40 Thd
(8.0) Dia
.315
When using this bushing, toggle length is increased
by .070” (1.78mm). Maximum Panel Thickness
with Standard Hardware: .031” (0.8mm)
Maximum Panel Thickness with
Standard Hardware: .102” (2.6mm)
Panel Cutouts
For A2, S2, A1 or
S1 Bushing
with Keyway
(5.6)
.220
(6.5) Dia
.256
(0.6)
.024
(0.9)
.035
(8.9)
.350
Indicators
(8.0) Dia
.315
Touch
(2.5)
.098
(0.9)
.035
(7.1)
.280
For A1 or
S1 Bushing
with Locking Ring
(6.5) Dia
.256
(2.2) Dia
.087
www.nkk.com
Accessories
(2.5)
.098
1/4-40 Thd
Standard Hardware:
(6.5)
.256
2 Hex Nuts (AT513H)
1 Lockwasher (AT509)
1 Locking Ring (AT507H)
Supplement
(0.8)
.031
For dimensions, see Accessories
& Hardware section.
A69
LOCKING LEVER & BUSHING
LL2
Locking Mechanism
Smooth with Keyway
Rotaries
on-none-on
on-none-(on)
on-off-(on)
on-on-(on)
on-off-on
on-on-on
(on)-off-(on)
(on)-on-(on)
2 positions lock
1 position locks
2 positions lock
3 positions lock
1 position locks
(0.8)
.031
(8.0) Dia
.315
(2.5)
.098
25°
(5.1) Dia
.201
(16.5)
.650
(8.0)
.315
(15.0)
.591
(9.3) (7.0)
.366 .275
No Code
Cap for Locking Lever
(4.6) Dia
.181
Color Codes for Optional
Anodized Aluminum Caps
Supplied with Cap AT427
Material & Finish:
(6.2) Dia
.244
A
Brass with Nickel Plating
Lever Material & Finish:
(0.9)
.035
G
Brass with Chrome Plating
Keylocks
Programmable Illuminated PB
Angle PC Mount Miniature Toggles
A
Pushbuttons
Rockers
Toggles
Series M
C
Black
Red
Blue
CONTACT MATERIALS & RATINGS
W
Slides
G
Silver over Silver
Power Level
6A @ 125V AC & 3A @ 250V AC
Gold over Brass or Copper
Logic Level
0.4VA maximum @ 28V AC/DC maximum
Note: See Supplement section to find complete explanation of operating range.
Tactiles
A
Power Level
or Logic Level
Gold over Silver
6A @ 125V AC
or 0.4VA maximum @ 28V AC/DC maximum
Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within
the same application. See Supplement section to find complete explanation of dual rating and operating range.
Tilt
TERMINALS
.150” (3.81mm)
Right Angle PC (1-3 Pole)
32
Indicators
Touch
30
3
2
(4.7) Typ
.185
1
6
5
4
3
2
1
(4.7) Typ
.185
(3.81)
.150
9
8
7
6
5
4
3
2
1
Right Angle PCB
with Reverse Circuit
(1 Pole & 0.4VA Rating Only)
(4.7) Typ
.185
(3.81) Typ
.150
1
(12.7)
.500
Accessories
(1.8) Dia Typ
.073
(2.54) Typ
.100
Supplement
Single Pole
(12.7)
.500
(2.54) Typ
.100
(1.8) Dia Typ
.073
Double Pole
(14.35)
.565
(2.54) Typ
.100
(1.8) Dia Typ
.073
Three Pole
Terminal dimensions are shown on the Typical Switch Dimensions pages which follow.
A70
www.nkk.com
2
3
(3.96) Typ
.156
(9.27)
.365
(2.54) Typ
.100
(1.8) Dia Typ
.073
(3.81) Typ
.150
1
1
4
9
2
5
8
1
4
7
(2.54) Typ
.100
(1.8) Dia Typ
.073
(4.8)
.189
(2.54) Typ
.100
6
2
2
5
1
1
4
3
Single Pole
12
2
5
8
11
1
4
7
10
9
2
5
8
1
4
7
(2.54) Typ
.100
Double Pole
(4.8) Typ
.189
(3.81) Typ
.150
(2.54) Typ
.100
(1.8) Dia Typ
.073
Four Pole
(2.54) Typ
.100
3
(4.8) Typ
.189
6
9
12
2
5
8
11
1
4
7
10
(14.35)
.565
(1.8) Dia Typ
.073
(2.54) Typ
.100
9
(14.35)
.565
(4.8) Typ
.189
6
(12.7)
.500
(1.8) Dia Typ
.073
6
Three Pole
(2.54) Typ
.100
3
(3.81) Typ
.150
3
(2.54) Typ
.100
(1.8) Dia Typ
.073
Double Pole
3
(4.8) Typ
.189
(14.35)
.565
(2.54) Typ
.100
(1.8) Dia Typ
.073
(12.7)
.500
(2.54) Typ
.100
(3.81) Typ
.150
(12.7)
.500
.100” (2.54mm)
Vertical PC (1-4 Pole)
(2.54) Typ
.100
6
5
(12.7)
.500
Single Pole
45
3
2
6
(14.35)
.565
(1.8) Dia Typ
.073
(1.8) Dia Typ
.073
(2.54) Typ
.100
Three Pole
Four Pole
Rockers
2
3
Pushbuttons
3
(2.4) Typ
.094
Programmable Illuminated PB
.150” (3.81mm)
Vertical PC (1-4 Pole)
Rotaries
40
Keylocks
A
TERMINALS (Continued)
Toggles
Series M
Angle PC Mount Miniature Toggles
Terminal dimensions are shown on the Typical Switch Dimensions pages which follow.
AT444
Conical Cap for S Bat Toggle
C
25°
Material:
Polyethylene
25°
(5.0) Dia
.197
(13.5)
.532
(12.0)
.472
Material:
Polyethylene
(4.8) Dia
.189
(13.1)
.516
(11.5)
.452
Colors Available
A
Black
E
Yellow
B
White
F
Green
C
Red
G
Blue
(12.0) Dia
.472
(2.0)
.079
Accessories
(6.0) Dia
.236
1/4-40 Thd or
M6 P0.75
(8.0)
.315
AT509
Lockwasher (1 per switch, none
with splashproof)
Steel with Zinc/Chromate
Indicators
AT507H for Inch
AT507M for Metric
Locking Ring (1 per switch)
Steel with Zinc/Chromate
Touch
STANDARD HARDWARE
AT513H for Inch
AT513M for Metric
Hex Nut (2 per switch)
Brass/Nickel
(6.4) Dia (10.2) Dia
.252
.402
(1.5)
.059
(1.7)
.067
(0.8)
.031
www.nkk.com
Supplement
(5.5)
.217
(9.0)
.354
Tactiles
AT415
for S Bat Toggle
Tilt
B
Slides
OPTIONAL CAPS & CAP COLORS
(0.5)
.020
A71
Toggles
Series M
Angle PC Mount Miniature Toggles
A
TYPICAL SWITCH DIMENSIONS
Rockers
.150” (3.81mm) Right Angle PC
Single Pole
(6.2) Dia
.244
Keyway
(2.9)
.114
(1.4) Typ
.055
(5.08)
.200
3
(7.9)
.311
(6.86)
.270
(0.4)
.016
(1.09)
.043
(12.7)
.500
(7.32)
.288
(0.8) Typ
.031
(4.7) Typ
.185
(1.27)
.050
(13.0)
.512
M2012S2A2G30
.150” (3.81mm) Right Angle PC
Keyway
Double Pole
(6.2) Dia
.244
4
5
6
1
2
3
(12.7)
.500
(4.3)
.169
(2.9)
.114
(1.4) Typ
.055
(5.08)
.200
Rotaries
Slides
2
(4.3)
.169
Keylocks
Programmable Illuminated PB
Pushbuttons
1
(6.86)
.270
(7.32)
.288
(0.4)
.016
(1.09)
.043
(12.7)
.500
(0.8) Typ
.031
(4.7) Typ
.185
(1.27) Typ
.050
(3.81)
.150
(13.0)
.512
M2022S2A2G30
.150” (3.81mm) Right Angle PC
(6.2) Dia
.244
(0.9)
.035
Tactiles
Keyway
Three Pole
7
8
9
4
5
6
1
2
3
(17.5)
.689
(2.9)
.114
(1.4) Typ
.055
(5.08)
.200
M2032S2A2G30
Right Angle PCB
Indicators
Touch
Tilt
(4.3)
.169
(6.86)
.270
(8.0)
.315
(0.4)
.016
(1.8)
.071
(14.35)
.565
(1.27) Typ
.050
(0.8) Typ
.031
(4.7) Typ
.185
(13.0)
.512
(3.81) Typ
.150
Single Pole • Reverse Circuit
25°
Accessories
Keyway
(2.7) Dia
.106
(6.2) Dia
.244
(7.9)
.311
(4.55)
.179
(0.9)
.035
(6.2)
.245
(6.86)
(8.9)
.270
.350
Supplement
(1.4) Typ
.055
(5.08)
.200
M2012S2A2G32
A72
www.nkk.com
(0.4)
.016
(9.3)
.365
(0.8)
.031
3
2
(2.7)
.106
(13.0)
.512
1
(8.5)
.335
(1.4) Typ
.055
(3.96) Typ
.156
A
TYPICAL SWITCH DIMENSIONS
.150” (3.81mm) Vertical PC
Rockers
Single Pole
(6.2) Dia
.244
Keyway
Toggles
Series M
Angle PC Mount Miniature Toggles
3
1
(2.7) Dia
.106
(1.4) Typ
.055
(5.08)
.200
(6.86)
.270
(7.32)
.288
(0.4)
.016
(1.1)
.043
(12.7)
.500
(0.8) Typ
.031
(3.81) Typ
.150
(2.7)
.106
(1.27)
.050
(7.9)
.311
M2012S2A2G40
Double Pole
.150” (3.81mm) Vertical PC
(6.2) Dia
.244
(2.7) Dia
.106
(1.4) Typ
.055
(5.08)
.200
(6.86)
.270
(7.32)
.288
(0.4)
.016
(1.1)
.043
(12.7)
.500
3
5
2
4
1
(2.7)
.106
(0.8) Typ
.031
(3.81) Typ
.150
(13.0)
.512
Keylocks
25°
6
(1.27) Typ
.050
(4.8)
.189
(12.7)
.500
Rotaries
Keyway
M2022S2A2G40
Three Pole
.150” (3.81mm) Vertical PC
25°
(2.7) Dia
.106
(1.4) Typ
.055
(5.08)
.200
(6.86)
.270
(8.0)
.315
(0.4)
.016
(1.8)
.071
(14.35)
.565
(0.8) Typ
.031
(3.81) Typ
.150
(2.7)
.106
9
6
3
8
5
2
7
4
1
Tactiles
(0.9)
.035
(13.0)
.512
(4.8) Typ
.189
(17.5)
.689
(1.27) Typ
.050
Tilt
(6.2) Dia
.244
Keyway
Programmable Illuminated PB
Pushbuttons
(13.0)
.512
2
Slides
25°
Four Pole
(2.7) Dia
.106
(1.4) Typ
.055
(5.08)
.200
(6.86)
.270
(8.0)
.315
(0.4)
.016
(1.8)
.071
(14.35)
.565
(0.8) Typ
.031
(3.81) Typ
.150
(2.7)
.106
9
6
3
11
8
5
2
10
7
4
1
(4.8) Typ
.189
(22.3)
.878
(13.0)
.512
Accessories
25°
12
Indicators
(0.9)
.035
(1.27) Typ
.050
Supplement
(6.2) Dia
.244
Keyway
.150” (3.81mm) Vertical PC
M2042S2A2G40
www.nkk.com
Touch
M2032S2A2G40
A73
Toggles
Series M
Angle PC Mount Miniature Toggles
A
TYPICAL SWITCH DIMENSIONS
Single Pole
Rockers
.100” (2.54mm) Vertical PC
(6.2) Dia
.244
Keyway
3
(13.0)
.512
2
1
(2.7) Dia
.106
(1.4) Typ
.055
(5.08)
.200
(6.86)
.270
(7.32)
.288
(0.4)
.016
(1.1)
.043
(12.7)
.500
(0.8) Typ
.031
(2.54) Typ
.100
(2.7)
.106
(1.27)
.050
(7.9)
.311
M2012S2A2G45
.100” (2.54mm) Vertical PC
Double Pole
(6.2) Dia
.244
Keyway
Keylocks
Programmable Illuminated PB
Pushbuttons
25°
25°
(2.7) Dia
.106
Rotaries
(1.4) Typ
.055
(5.08)
.200
(6.86)
.270
(7.32)
.288
(0.4)
.016
(1.1)
.043
(12.7)
.500
6
3
5
2
4
1
(2.7)
.106
(0.8) Typ
.031
(2.54) Typ
.100
(13.0)
.512
(1.27) Typ
.050
(4.8)
.189
(12.7)
.500
Slides
M2022S2A2G45
Three Pole
.100” (2.54mm) Vertical PC
(6.2) Dia
.244
Tactiles
Keyway
(0.9)
.035
25°
(2.7) Dia
.106
Tilt
(1.4) Typ
.055
(5.08)
.200
(6.86)
.270
(8.0)
.315
(0.4)
.016
(1.8)
.071
(14.35)
.565
(0.8) Typ
.031
(2.54) Typ
.100
(2.7)
.106
9
6
3
8
5
2
7
4
1
(13.0)
.512
(4.8) Typ
.189
(17.5)
.689
(1.27) Typ
.050
.100” (2.54mm) Vertical PC
Indicators
Touch
M2032S2A2G45
Four Pole
(6.2) Dia
.244
Keyway
(0.9)
.035
Accessories
25°
(2.7) Dia
.106
Supplement
(1.4) Typ
.055
(5.08)
.200
(6.86)
.270
M2042S2A2G45
A74
www.nkk.com
(8.0)
.315
(0.4)
.016
(1.8)
.071
(14.35)
.565
(0.8) Typ
.031
(2.54) Typ
.100
(2.7)
.106
12
9
6
3
11
8
5
2
10
7
4
1
(4.8) Typ
.189
(22.3)
.878
(13.0)
.512
(1.27) Typ
.050
Similar pages