CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 C learance N o.: FT DI# 4 9 3 Future Technology Devices International Limited Datasheet CleO35 Module 1 Introduction 1.1 The CleO35 is a smart TFT display shield for Arduino. It includes a 3.5 inch 320x480 pixel TFT LCD panel with resistive touch, PWM audio output with in-built speaker amplifier for better audio quality The CleO35 utilises the FTDI FT903 low power MCU to bridge between the Arduino and fast interface accessories such as camera and SD Card input. For a full list of the FT903’s features please see the FT90X datasheet .In addition, the CleO35 has the following features: These smart TFT display shields can be easily programmed by almost anyone to give professional looking HMI / GUI's with no prior knowledge of complex graphics programming or mathematics. Features Landscape and portrait modes supported In built FTDI FT810 embedded video engine (EVE) graphic controller Anti-Aliased graphics throughout for much finer image quality with no "jaggies". Ready to use LCD module with resistive touch in panel mountable bezel. Micro SD card socket support. In built 8M Byte Eflash memory USB DFU port for firmware updates Support camera interface PWM audio supported and in built speaker amplifier Designed as Arduino and NerO shield Compatible with FTDI CleO-RIO, CleO-Camera and CleO-Speaker. CE and FCC certified N either the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or elec tronic form without the prior written c onsent of the c opyright holder. T his product and its doc umentation are s upplied on an as- is basis and no warranty as to their s uitability for any partic ular purpos e is either made or implied. Future T ec hnology Devic es I nternational L td will not accept any claim for dama ges hows oever arising as a res ult of use or failure of this produc t. Y our statutory rights are not affected. T his produc t or any variant of it is not intended for us e in any medical appliance, device or s ystem in whic h the failure of the produc t might reas onably be expected to res ult in pers onal injury. T his doc ument provides preliminary information that may be s ubject to c hange without notice. N o freedom to use patents or other intellec tual property rights is implied by the publication of this doc ument. Fu ture Tec hnology D evices I nternational L td, U nit 1 , 2 Seaward P lac e, C enturion Business P ark, G lasgow G 4 1 1HH U nited Kingdom. Sc otland Registered C ompany N umber: SC 136640 Copyright © Future Technology Devices International Limited 1 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 C learance N o.: FT DI# 4 9 3 2 Ordering Information Part No. Description CleO35A CleO35 module, with FPC/FFC 50 LCD connector, 3.5 inch TFT LCD display panel preinstalled, with resistive touch. Black bezel. CleO-RIO1 Arduino Shield for users to stack Arduino board on bottom of CleO35. CleO-CAM1 A camera plug-in module for CleO35. CleO-SPK1 A speaker enclosure with connecting wires to CleO35. 3 Program Support The demo applications are provided for CleO35 modules by FTDI. Visit FTDI’s website at http://www.ftdichip.com/Products/Modules/CleO.htm for more information. Copyright © Future Technology Devices International Limited 2 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 C learance N o.: FT DI# 4 9 3 Table of Contents 1 Introduction ................................................................. 1 1.1 Features ................................................................................ 1 2 Ordering Information .................................................... 2 3 Program Support .......................................................... 2 4 Module Hardware Feature ............................................. 5 4.1 Power Supply......................................................................... 6 4.2 Micro-controller ..................................................................... 6 4.3 Micro SD Interface ................................................................. 7 4.4 LCD Interface......................................................................... 7 4.5 Camera Interface ..................................................................10 4.6 Audio Output ........................................................................11 4.7 SPI Slave Interface ...............................................................12 4.8 External IO Pin .....................................................................13 4.9 Power and Program Interface................................................14 5 Devices Characteristics and Ratings............................. 15 5.1 Electrical Specification ..........................................................15 5.2 Display Specification .............................................................15 5.3 Optical Specification..............................................................16 6 Board Schematic ......................................................... 18 7 Block Diagram ............................................................ 21 8 Mechanical Dimensions ............................................... 22 8.1 CleO35 Module Dimensions....................................................22 8.2 Bezel Drawing.......................................................................23 9 Contact Information .................................................... 24 Appendix A – References ................................................. 25 Document References ...................................................................25 Acronyms and Abbreviations .........................................................25 Appendix B - List of Figures and Tables ............................ 26 Copyright © Future Technology Devices International Limited 3 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 C learance N o.: FT DI# 4 9 3 List of Figures ...............................................................................26 List of Tables ................................................................................26 Appendix C – Revision History.......................................... 27 Copyright © Future Technology Devices International Limited 4 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 C learance N o.: FT DI# 4 9 3 4 Module Hardware Feature The dimensions of the CleO35 module are 101.4 mm x 73 mm X15mm. See Figure 1 for all the hardware features. Figure 1 – CleO35 Bottom View Key Features: 1 3 Speaker out / Line in 3.5 in HVGA TFT I/F + Resistive Touch 5 Arduino I/F 7 8M Byte E-Flash 9 MicroSD Card Socket 11 FT903 MCU 13 FT810 GPU 2 Plastic Bezel 4 Arduino Configuration Jumpers 6 Level Shifter 8 FT903 IO Expansion 10 Camera Interface 12 USB DFU Connector 14 Audio Amplifier Copyright © Future Technology Devices International Limited 5 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 C learance N o.: FT DI# 4 9 3 4.1 Power Supply The CleO35 module receives power externally. Users can combine the module with the FCC/CE certified NerO or Arduino UNO and draw power from those board supplies . For details of the NerO module, refer to FTDI-NerO for more Information. Alternatively, the on-board USB connector, CN4 which is primarily for debug purpose and DFU firmware upgrade may also supply power. Once the 5V supply is applied, a Red LED power indicator will be turned on. A step down regulator U15 will step down the 5V to 3.3V. The 3.3V supply will serve all peripherals of the FT903 microcontroller. Figure 2 - Power Supply 4.2 Micro-controller The FT903Q 100-pin QFN microcontroller which is provided on the board belongs to 32-bit FT90X Super Bridging Microcontroller family from FTDI Chip. For details of the FT903Q Microcontroller, refer to the FT90X datasheet. Figure 3 - Micro-Controller Copyright © Future Technology Devices International Limited 6 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 C learance N o.: FT DI# 4 9 3 4.3 Micro SD Interface A Micro SD card slot is provided on CleO35 supporting two standards capacity card types: Secure Digital (SD) standard – Up to 2GB SD memory card Secure Digital High Capacity (SDHC) standard – Over 2GB-32GB SDHC memory card The SD host controller is compatible with the standard specification V3.0. It supports up to 25MHz SD clock speed. In the CleO35 design, the physical interface supports 4-bit SD bus mode and card detection. Figure 4 - MicroSD Interface 4.4 LCD Interface In the CleO35 design, a 3.5 inch TFT LCD with resistive touch is supported. The FT810Q 48pin VQFN graphics controller IC with integrated touch and audio belongs to FTDI’s EVE series. For further details of the FT810Q EVE graphics controller, refer to the FT81X datasheet. The 3.5 inch LCD is connected through the 50 pin FPC/FFC connector CN1. See Table 1 for the LCD connector pinout. Pin No 1 2 3 Name GND Description Ground LEDA Backlight LED Anode LEDK Backlight LED cathode Copyright © Future Technology Devices International Limited 7 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 Pin No 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 C learance N o.: FT DI# 4 9 3 Name LEDK Description Backlight LED cathode LEDK Backlight LED cathode LEDK Backlight LED cathode LEDK Backlight LED cathode LEDK Backlight LED cathode GND Ground GND Ground VDD3V3 LCD VCC supply VDD3V3 LCD VCC supply LCD_RST Reset SPIM_SSn1 SPI chip select LCD_RS RS SPIM_SCK SPI clock GND ground SPIM_MOSI Master output slave input LCD_SDO Master input slave output LCD_B2 Bit2 of blue RGB signal LCD_B3 Bit3 of blue RGB signal LCD_B4 Bit4 of blue RGB signal LCD_B5 Bit5 of blue RGB signal LCD_B6 Bit6 of blue RGB signal LCD_B7 Bit7 of blue RGB signal LCD_G2 Bit2 of green RGB signal LCD_G3 Bit3 of green RGB signal LCD_G4 Bit4 of green RGB signal LCD_G5 Bit5 of green RGB signal LCD_G6 Bit6 of green RGB signal LCD_G7 Bit7 of green RGB signal LCD_R2 Bit2 of red RGB signal LCD_R3 Bit3 of red RGB signal LCD_R4 Bit4 of red RGB signal LCD_R5 Bit5 of red RGB signal LCD_R6 Bit6 of red RGB signal LCD_R7 Bit7 of red RGB signal DE Data enable Copyright © Future Technology Devices International Limited 8 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 Pin No 39 40 41 42 43 44 45 46 47 48 49 50 C learance N o.: FT DI# 4 9 3 Name DCLK Description Pixel clock HSYNC LCD horizontal sync VSYNC LCD vertical sync - IM2 - IM1 - IM0 GND ground YP Y Top electrode of resistive touch X left electrode of resistive touch Y bottom electrode of resistive touch X right electrode of resistive touch ground XM YM XP GND Table 1 - LCD Connector Pin Out Figure 5 - LCD Interface Copyright © Future Technology Devices International Limited 9 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 C learance N o.: FT DI# 4 9 3 4.5 Camera Interface The CleO35 has a camera module interface, via a 24-pin 0.5mm pitch FFC/FPC, bottom contact connector, CN3.In this design, support is provided for an OmniVision OV2640 camera module. A readymade camera module (CleO-CAM1A) can be purchase from FTDI. Support for further camera modules may be added in the future . Please visit the FTDI website for more information. See table 2 for the Camera interface pinout Pin No Name Description 1 GND Ground 2 GND Ground 3 I2C0_SDA I2C serial bus, data line 4 CAM_5V 5V power supply 5 I2C0_SCL I2C serial bus, clock line 6 RESET# Hardware reset, active low 7 CAM_VD Camera vertical sync input 8 CAM_PWDN Camera module power down signal, active high 9 CAM_HD Camera horizontal reference input 10 CAM_3V3 3.3V power supply 11 CAM_3V3 3.3V power supply 12 CAM_D7 Camera data line, Bit 7 13 CAM_XCLK Camera external clock output 14 CAM_D6 Camera data line, Bit 6 15 GND Ground 16 CAM_D5 Camera data line, Bit 5 17 CAM_PCLK Camera pixel clock input 18 CAM_D4 Camera data line, Bit 4 19 CAM_D0 Camera data line, Bit 0 20 CAM_D3 Camera data line, Bit 3 21 CAM_D1 Camera data line, Bit 1 22 CAM_D2 Camera data line, Bit 2 23 CAM_5V 5V power supply 24 PWM0 Pulse width modulation Table 2 - Camera Connector Pin Out Copyright © Future Technology Devices International Limited 10 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 C learance N o.: FT DI# 4 9 3 Figure 6 - Camera Interface 4.6 Audio Output CleO35 supports a mono speaker output through CN13. Maximum output power, can drive up to 8 OHM, 1 Watt speaker driver. A readymade speaker module (CleO-SPK1) is also available from FTDI; visit the FTDI Chip website for more information. An alternative, mono line-in audio input is also provided on CN13. Users can drive in their own audio source to the on board power amplifier. See the Table 3 for the pin list for CN13. Pin No Pin Name Description 1 SP- Speaker out negative 2 SP+ Speaker out positive 3 GND Ground 4 EXT_AUD Ext audio line in Table 3 - Pin List of CN3 Copyright © Future Technology Devices International Limited 11 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 C learance N o.: FT DI# 4 9 3 Figure 7 - Speaker Amplifier Circuitry 4.7 SPI Slave Interface The CleO35 has a SPI slave interface that supports single and dual (2 data lines) SPI data transfer modes. This interface supports both 5V, 3.3V and user defined output levels. The user defined interface levels must be between 3V (min) to 5.5V (max). The power selection jumper is through CN10. Pin Number Description 5V SPI interface 1-2 3.3V SPI interface 3-4 SPI interface voltage level follow s user setting(IOREF) Table 4 - CN10 Jumper Selection 5-6 There are chip select (CS) jumper selections on CN11. The user has 3 options to choose for their connection. Description Pin Number SPI chip select from D5(option 1) 1-2 SPI chip select from D7(option 2) 3-4 SPI chip select from D10(option 3) 5-6 Table 5 - CN11 Jumper Selection For the SPI Slave interface, there are two connectors for the user to interface with the master side. The CN9 – 1X10 position 2.54mm pitch female header The CN8 – 1X8 position 2.54mm pitch female header Pin Number Name Description 1 - No connection 2 - No connection 3 D10 SPI Chip select option3 4 MOSI SPI data from master side Copyright © Future Technology Devices International Limited 12 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 C learance N o.: FT DI# 4 9 3 Pin Number Name Description 5 MISO SPI data to master side 6 SCK SPI clock 7 GND Ground 8 - No connection 9 - No connection 10 - No connection Table 6 - CN9 Pin List Pin Number Name Description 1 - No connection 2 - No connection 3 D2 FT903 Interrupt request out option 1 4 D3 FT903 Interrupt request out option 2 5 - No connection 6 D5 SPI Chip select option1 7 - No connection 8 D7 SPI Chip select option2 Table 7 - CN8 Pin List 4.8 External IO Pin There are extra features provided on CN5, 16 position 0.5mm pitch FFC/FPC connector. Users can connect to external feature boards through this connector. See Table 8 for all the extra feature s assigned to each pin. Pin Number 1 2 3 4 5 6 7 8 9 Name Description GPIO61 General purpose IO 61 GPIO60 General purpose IO 60 PWM2 Pulse Width Modulation 2 PWM1 Pulse Width Modulation 1 VDD3V3 3.3V supply GND Ground I2C1_SCL I2C1 Serial Clock I2C1_SDA I2C1 Serial Data UART0_RXD UART0 receive Copyright © Future Technology Devices International Limited 13 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 10 11 12 13 14 15 16 UART0_TXD UART0 transmit VDD3V3 3.3V supply GND Ground SPIM_MISO SPI3 Master Input SPIM_MOSI SPI3 Master Output SPIM_SSn3 SPI3 Chip Select SPIM_SCK SPI3 Clock Line C learance N o.: FT DI# 4 9 3 Table 8 - CN5 Pin List There is a jumper selection for the FT903 interrupt request through CN12. Users have 2 option to choose from. Pin Number Description Connect to Arduino/NerO MCU int0(D2) 1-2 Connect to Arduino/NerO MCU int1(D3) 3-4 Table 9 - CN12 Jumper Selection 4.9 Power and Program Interface The power interface CN6, 1X8 position 2.54mm pitch female heade r, may be driven by NerO or an Arduino UNO. Users can use the USB connector CN4 for FT903 firmware upgrades. For the details of the tool operation, refer to AN_325 FT900 Tool Chain Installation Guide . Pin Number Name Description 1 NC NC 2 IOREF IO reference voltage 3 RESET FT903 reset pin 4 - No connection 5 VDD5V 5V supply 6 GND ground 7 GND ground 8 - No connection Table 10 - CN6 Pin List Copyright © Future Technology Devices International Limited 14 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 C learance N o.: FT DI# 4 9 3 5 Devices Characteristics and Ratings 5.1 Electrical Specification Conditions Parameter Value Unit Storage Temperature -30°C to 80°C Degrees C Ambient Operating Temperature (Power -20°C to 70°C Degrees C Applied) Table 11 - Temperature Parameter DC Characteristics (Ambient Temperature = -20°C to +70°C) Parameter Description Minimum Typical Maximum Units V bus USB power supply 4.75 5.25 V V DC DC power supply 4.75 5.25 V Iusb USB power supply current 500 mA IDC DC Supply Current 500 mA I USB current in idle mode idle 140 mA Vio 3.3 Vio voltage reference 3.0 Vih Input high voltage 2 Vil Input low voltage Voh output high voltage Vol output low voltage 0.4 Table 12 - Operating Voltage and Current 3.3 3.6 Conditions External source With LCD and backlight on V 0.8 2.4 5.2 Display Specification Item Spec Units Display area(AA) 49.0(H) * 73.4(V) mm Driver Element TFT active matrix mA Display Colours 262K - Number of Pixels 320(RGB)*480 dots Pixel pitch 0.051(H) * 0.051(V) mm Copyright © Future Technology Devices International Limited Notes 3.5 inch diagonal 15 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 Item Spec Units Viewing Angle 6:00 o’clock Display mode Transmissive/ Normally White - LCD Luminance 100 cd/m2 Touch screen resistive Table 13 - Display Specifications C learance N o.: FT DI# 4 9 3 Notes Portrait view - 5.3 Optical Specification Copyright © Future Technology Devices International Limited 16 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 C learance N o.: FT DI# 4 9 3 Figure 8 - 3.5 inch TFT Optical Specifications Copyright © Future Technology Devices International Limited 17 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 C learance N o.: FT DI# 4 9 3 6 Board Schematic Figure 9 - Sheet1 - FT810Q Connection Copyright © Future Technology Devices International Limited 18 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 C learance N o.: FT DI# 4 9 3 Figure 10 - Sheet2 - FT903Q Connection Copyright © Future Technology Devices International Limited 19 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 C learance N o.: FT DI# 4 9 3 Figure 11 - Sheet3 - Power and Connectors Copyright © Future Technology Devices International Limited 20 Speaker Connector 3.5 inch TFT LCD with resistive Touch Speaker Amplifier RGB PWM Copyright © Future Technology Devices International Limited External connector External connector CN5 Serial Flash W25Q64F V SPIM 1 FT810 MicroSD card Slot SPIS 1 SPIM 3 SPIM 2 SPIM 0 SDIO FT903 Q GPIO I2C1 PWM1 & PWM2 UART0 DP & DM PWM0 I2C0 CAM_D Interface External connector CN5 Debug port Micro USB Slot Camera CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 C learance N o.: FT DI# 4 9 3 7 Block Diagram Figure 12 - CleO35 Block Diagram 21 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 C learance N o.: FT DI# 4 9 3 8 Mechanical Dimensions 8.1 CleO35 Module Dimensions 101.4mm 73mm 15mm Figure 13 - Cleo35 Module Dimensions Copyright © Future Technology Devices International Limited 22 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 C learance N o.: FT DI# 4 9 3 8.2 Bezel Drawing Figure 14 - CleO35 Bezel Drawing Copyright © Future Technology Devices International Limited 23 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 C learance N o.: FT DI# 4 9 3 9 Contact Information Head Office – Glasgow, UK Branch Office – Tigard, Oregon, USA Future Technology Devices International Limited Unit 1, 2 Seaward Place, Centurion Business Park Glasgow G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 Future Technology Devices International Limited (USA) 7130 SW Fir Loop Tigard, OR 97223-8160 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) E-mail (Sales) E-mail (Support) E-mail (General Enquiries) [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] Branch Office – Taipei, Taiwan Branch Office – Shanghai, China Future Technology Devices International Limited (Taiwan) 2F, No. 516, Sec. 1, NeiHu Road Taipei 114 Taiwan , R.O.C. Tel: +886 (0) 2 8797 1330 Fax: +886 (0) 2 8751 9737 Future Technology Devices International Limited (China) Room 1103, No. 666 West Huaihai Road, Shanghai, 200052 C hina Tel: +86 21 62351596 Fax: +86 21 62351595 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) E-mail (Sales) E-mail (Support) E-mail (General Enquiries) tw [email protected] tw [email protected] tw [email protected] [email protected] [email protected] [email protected] Web Site http://ftdichip.com Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. System and equipment manufac turers and des igners are res ponsible to ens ure that their s ys tems , and any Future T ec hnolog y D evices I nternational L td (FTDI ) devices incorporated in their sys tems , meet all applic able safety, regulatory and sys tem -level performance requirements . All application- related information in this document (including applic ation desc riptions , s uggested FTDI devic es and other materials ) is provided for referenc e only. While FTDI has taken care to ass ure it is acc urate, this information is s ubject to c ustomer confirmation, and FTDI disclaims all liability for s ys tem des igns and for any applic ations ass ista nce provided by FTDI . Use of FTDI devic es in life s upport and/or s afety applic ations is entirely at the user’s risk, and the us er agrees to defend, indemnify and hold harmless FTDI from any and all damages , claims , s uits or expense res ulting from s uch us e. T his doc ument is s ubject to c hange without notice. N o freedom to us e patents or other intellec tual property rights is implied by the public ation of this doc ument. N either the whole nor any part of the information c ontained in, or the produc t d esc ribed in this doc ument, may be adapted or reproduc ed in any material or elec tronic form without the prior written c onsent of the c opyright holder. Future Tec hnology Devices I nternational L td, U nit 1 , 2 Seaward P lac e, Centurion Business Park, Glas gow G41 1HH , U nited Kingdom. Scotland Registered C ompany N umber: SC136640 Copyright © Future Technology Devices International Limited 24 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 C learance N o.: FT DI# 4 9 3 Appendix A – References Document References For module documentations, please refer to URL below: FT90X series datasheet: FT90X Series Datasheet FT900 tool chain installation guide : FT900 Tool Chain Installation Guide FT900 Bootloader DFU usage guide: FT900 Bootloader DFU Usage Application Note Acronyms and Abbreviations Terms Description DC Direct Current DFU Device Firmware Update EVE Embedded Video Engine FCC/CE North American EMI Verification/European Union EMC & Safety Compliance Declaration FFC/FPC Flexible Flat Cable/Flexible Printed Circuit GPU HVGA IO Graphics Processing Unit Half Size Video Graphics Array Input/output LCD Liquid Crystal Display LED Light-emitting diode MCU Microcontroller Unit QFN Quad-flat no-leads SD Secure Digital SPI Serial Peripheral Interface SDHC USB VQFN Secure Digital High Capacity Universal Serial Bus Very Thin Quad Flat Non-Leaded Package Copyright © Future Technology Devices International Limited 25 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 C learance N o.: FT DI# 4 9 3 Appendix B - List of Figures and Tables List of Figures Figure 1 – CleO35 Bottom View .............................................................................................................. 5 Figure 2 - Power Supply ......................................................................................................................... 6 Figure 3 - Micro-Controller...................................................................................................................... 6 Figure 4 - MicroSD Interface................................................................................................................... 7 Figure 5 - LCD Interface ......................................................................................................................... 9 Figure 6 - Camera Interface ................................................................................................................. 11 Figure 7 - Speaker Amplifier Circuitry ................................................................................................... 12 Figure 8 - 3.5 inch TFT Optical Specifications ........................................................................................ 17 Figure 9 - Sheet1 - FT810Q Connection ................................................................................................ 18 Figure 10 - Sheet2 - FT903Q Connection .............................................................................................. 19 Figure 11 - Sheet3 - Power and Connectors .......................................................................................... 20 Figure 12 - CleO35 Block Diagram ........................................................................................................ 21 Figure 13 - Cleo35 Module Dimensions ................................................................................................. 22 Figure 14 - CleO35 Bezel Drawing ........................................................................................................ 23 List of Tables Table 1 - LCD Connector Pin Out ............................................................................................................ 9 Table 2 - Camera Connector Pin Out ..................................................................................................... 10 Table 3 - Pin List of CN3 ....................................................................................................................... 11 Table 4 - CN10 Jumper Selection .......................................................................................................... 12 Table 5 - CN11 Jumper Selection .......................................................................................................... 12 Table 6 - CN9 Pin List ........................................................................................................................... 13 Table 7 - CN8 Pin List........................................................................................................................... 13 Table 8 - CN5 Pin List ........................................................................................................................... 14 Table 9 - CN12 Jumper Selection .......................................................................................................... 14 Table 10 - CN6 Pin List ......................................................................................................................... 14 Table 11 - Temperature Parameter ....................................................................................................... 15 Table 12 - Operating Voltage and Current ............................................................................................. 15 Table 13 - Display Specifications .......................................................................................................... 16 Copyright © Future Technology Devices International Limited 26 CleO35 Module Datasheet Version 1.0 D oc ument Reference N o.: FT _001299 C learance N o.: FT DI# 4 9 3 Appendix C – Revision History Document Title: CleO35 Module Datasheet Document Reference No.: FT_001299 Clearance No.: FTDI# 493 Product Page: http://www.ftdichip.com/Products/Modules/CleO.htm Document Feedback: Send Feedback Revision Changes Date Version 1.0 Initial Release 2016-04-20 Copyright © Future Technology Devices International Limited 27