MTLP www.vishay.com Vishay Electro-Films Wire Bondable Thin Film Micro-Strip Transmission Line Resistor Arrays FEATURES • 50 micro-strip configuration • Wire bondable terminations • Alumina (99.6 %) substrate; as-fired or polished APPLICATIONS • Test and measurement setups • Network analyzer calibration elements • RF bread boarding Product may not be to scale • High frequency hybrid assemblies MTLP series of thin film 50 micro-strip transmission lines with two rows of tuning pads are designed for test and measurement applications. CUSTOM DESIGNED ELEMENTS Vishay EFI will custom design additional geometries and form factors upon request. Standard configurations of the MTLP series include an array of wire bondable terminations that allow integration of discrete components. Information about standard design rules can be found at www.vishay.com/doc?49109 Custom configurations including open, short and load element are available upon request. STANDARD ELECTRICAL SPECIFICATIONS PARAMETER Characteristic Impedance Mechanical Tolerances Operating Temperature Range VALUE UNIT 50 ± 0.1 (± 4 μm) mil -55 to +125 °C DIMENSIONS in inches 0.0012" (30 μm) 0.005" square (125 μm square) (0 .2 0 5 . up mm01" on t to re o 1 4" qu 00 es m t m ) 0.004" (100 μm) Full ground plane on back side 0.01" (250 μm) 0.01" (250 μm) 0.03" (750 μm) LENGTH WIDTH THICKNESS 0.01 to 0.5 0.03 ± 0.002 0.010 ± 0.001 Revision: 16-Nov-17 Document Number: 61097 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MTLP www.vishay.com Vishay Electro-Films MECHANICAL SPECIFICATIONS PARAMETER VALUE Substrate Thickness 10 mils ± 1 mils (as-fied) ± 0.5 mils (polished) Substrate Material Alumina 99.6 % Metallization TiW (750 ± 250 Å)/Au (120 μ" min.) Micro-strip Line Width 10 mils ± 0.1 mils Available Line Lengths 0.010" to 0.0500" ORDERING INFORMATION MTLP 300 P WS - 0.30" mil long transmission line on polished Alumina MODEL LENGTH SURFACE FINISH PACKAGING CODE MTLP Micro-strip transmission line with tuning pads XXX 010 015 020 055 090 300 F = As-fired P = Polished WS = 100 mult, 1 min. waffle pack Revision: 16-Nov-17 Document Number: 61097 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 08-Feb-17 1 Document Number: 91000