M54/74HC292/7292 M54/74HC294/7294 PROGRAMMABLE DIVIDER/TIMER . . . . . . . . HIGH SPEED fMAX = 70 MHz (TYP.) at VCC = 5 V LOW POWER DISSIPATION o ICC = 4 mA (MAX.) at TA = 25 C HIGH NOISE IMMUNITY VNIH = VNIL = 28 % VCC (MIN.) OUTPUT DRIVE CAPABILITY 10 LSTTL LOADS SYMMETRICAL OUTPUT IMPEDANCE | IOH|= IOL = 4 mA (MIN.) BALANCED PROPAGATION DELAYS tPLH = tPHL WIDE OPERATING VOLTAGE RANGE VCC (OPR) = 2 V TO 6 V PIN AND FUNCTION COMPATIBLE WITH 54/74LS292/294 B1R (Plastic Package) F1R (Ceramic Package) M1R (Micro Package) C1R (Chip Carrier) ORDER CODES : M54HCXXXF1R M74HCXXXM1R M74HCXXXB1R M74HCXXXC1R DESCRIPTION The 54/74HC292/7292 and HC294/7294 are high speed CMOS PROGRAMMABLE DIVIDER/TIMER fabricated with silicon C2MOS technology. They achieve the high speed operation similar to equivalent LSTTL while maintaining the CMOS low power dissipation. These devices are programmable frequency dividers. The types have two clock inputs, either one may be used for clock gating. (see the function table). The HC292/7292 can divide from 22 to 231, and the HC294/7294 can divide from 22 to 215. The types feature an active-low clear input to initialize the state of all flip-flops. To facilitate incoming inspection, test points are provided. (TP1, TP2 and TP3 on the HC292/7292 and TP on the HC294/7294). All inputs are equipped with protection circuits against static discharge and transient excess voltage. HC292/294 have Q output with ”Totem pole” configuration and test point TP with ”Open Drain” output configuration. HC7292/7294 have all outputs ”Totem Pole”. PIN CONNECTION (top view) HC292 HC7292 October 1993 HC294 HC7294 HC292 HC7292 HC294 HC7294 1/14 M54/M74HC292/7292/294/7294 INPUT AND OUTPUT EQUIVALENT CIRCUIT (TOTEM POLE OUTPUT) INPUT AND OUTPUT EQUIVALENT CIRCUIT (OPEN DRAIN OUTPUT, HC292/294) PIN DESCRIPTION (HC292/7292) PIN DESCRIPTION (HC294/7294) PIN No 4, 5 1, 2, 10, 14, 15 3, 6, 13 11 7 8 16 SYMBOL CLK1, CLK2 A to E NAME AND FUNCTION input Clock TP1, TP2, TP3 CLR Q GND V CC Test Point Outputs Program Inputs Clear (Active LOW) Output Ground (0V) Positive Supply Voltage PIN No 4, 5 1, 2, 14, 15 3 11 7 8 16 SYMBOL CLK1, CLK2 A to D TP1 CLR Q GND VCC NAME AND FUNCTION input Clock Program Inputs Test Point Output Clear (Active LOW) Output Ground (0V) Positive Supply Voltage IEC LOGIC SYMBOLS HC292/HC7292 HC294/HC7294 TRUTH TABLE CLEAR L H H H H 2/14 CLOCK1 X L H X CLOCK2 X L Q OUTPUT MODE CLEARED TO L UP COUNT X H NO CHANGE M54/M74HC292/7292/294/7294 LOGIC DIAGRAM (HC292/7292) 3/14 M54/M74HC292/7292/294/7294 LOGIC DIAGRAM (HC294/7294) 4/14 M54/M74HC292/7292/294/7294 FUNCTION TABLE (HC292/7292) PROGRAMMING INPUTS E L L L L L L L L L L L L L L L H H H H H H H H H H H H H H H H H D L L L L L L L L H H H H H H H H L L L L L L L L H H H H H H H H C L L L L H H H H L L L L H H H H L L L L H H H H L L L L H H H H B L L H H L L H H L L H H L L H H L L H H L L H H L L H H L L H H A L H L H L H L H L H L H L H L H L H L H L H L H L H L H L H L H Q BINARY DECIMAL Inhibit Inhibit Inhibit Inhibit 22 4 23 8 4 2 16 32 25 26 64 128 27 28 256 512 29 210 1,024 2,048 211 4,096 212 213 8,192 14 2 16,384 215 32,768 65,536 216 217 131,072 262,144 218 219 524,288 1,048,576 220 2,097,152 221 222 4,194,304 23 8,388,608 2 224 16,777,216 225 33,554,432 226 67,108,864 134,217,728 227 268,435,456 228 229 536,870,912 1,073,741,824 230 231 2,147,483,648 FREQUENCY DIVISION TP1 TP2 BINARY DECIMAL BINARY DECIMAL Inhibit Inhibit Inhibit Inhibit Inhibit Inhibit Inhibit Inhibit 29 512 217 131,072 29 512 217 131,072 9 17 2 512 2 131,072 29 512 217 131,072 29 512 217 131,072 29 512 217 131,072 29 512 217 131,072 29 512 217 131,072 29 512 217 131,072 29 512 217 131,072 29 512 217 131,072 29 512 217 131,072 9 2 512 Disabled Low 29 512 Disabled Low 29 512 23 8 9 2 512 23 8 29 512 25 32 29 512 25 32 9 2 512 27 128 29 512 27 128 Disabled Low 29 512 9 Disabled Low 2 512 23 8 211 2,048 23 8 211 2,048 5 2 32 213 8,192 25 32 213 8,192 27 128 215 32,768 27 128 215 32,768 9 2 512 217 131,072 29 512 217 131,072 BINARY Inhibit Inhibit 224 224 224 224 224 224 22 22 24 24 26 26 28 28 210 210 212 212 214 214 216 216 218 218 220 220 222 222 224 224 TP3 DECIMAL Inhibit Inhibit 16,777,216 16,777,216 16,777,216 16,777,216 16,777,216 16,777,216 4 4 16 16 64 64 256 256 1,024 1,024 4,096 4,096 16,384 16,384 65,536 65,536 262,144 262,144 1,048,576 1,048,576 4,194,304 4,194,304 16,777,216 16,777,216 5/14 M54/M74HC292/7292/294/7294 FUNCTION TABLE (HC294/7294) PROGRAMMING INPUTS D L L L L L L L L H H H H H H H H C L L L L H H H H L L L L H H H H B L L H H L L H H L L H H L L H H FREQUENCY DIVISION Q A L H L H L H L H L H L H L H L H TP BINARY Inhibit Inhibit 22 23 24 25 26 27 28 29 210 211 212 213 214 215 DECIMAL Inhibit Inhibit 4 8 16 32 64 128 256 512 1,024 2,048 4,096 8,192 16,384 32,768 BINARY Inhibit Inhibit 29 29 29 29 29 Disabled Low 22 23 24 25 26 27 28 29 DECIMAL Inhibit Inhibit 512 512 512 512 512 4 8 16 32 64 128 256 512 ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit -0.5 to +7 V -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 V V DC Input Diode Current ± 20 mA DC Output Diode Current DC Output Source Sink Current Per Output Pin ± 20 ± 25 mA mA VCC Supply Voltage VI VO DC Input Voltage DC Output Voltage IIK IOK IO ICC or IGND DC VCC or Ground Current PD Tstg Power Dissipation Storage Temperature TL Lead Temperature (10 sec) ± 50 mA 500 (*) -65 to +150 mW o C 300 o C Absolute Maximum Ratings are those values beyond which damage tothe device may occur. Functional operation under these conditions is not implied. (*) 500 mW: ≅ 65 oC derate to 300 mW by 10mW/oC: 65 oC to 85 oC RECOMMENDED OPERATING CONDITIONS Symbol Parameter Value Unit VCC Supply Voltage 2 to 6 V VI VO Input Voltage Output Voltage 0 to VCC 0 to VCC V V Top Operating Temperature: tr, tf Input Rise and Fall Time 6/14 M54HC Series M74HC Series -55 to +125 -40 to +85 VCC = 2 V VCC = 4.5 V 0 to 1000 0 to 500 VCC = 6 V 0 to 400 o o C C ns M54/M74HC292/7292/294/7294 DC SPECIFICATIONS Test Conditions Symbol VIH V IL Parameter High Level Input Voltage Low Level Input Voltage Value VCC (V) TA = 25 oC 54HC and 74HC Min. Typ. Max. 2.0 1.5 1.5 1.5 4.5 6.0 3.15 4.2 3.15 4.2 3.15 4.2 High Level Output Voltage (Q) 0.5 0.5 0.5 4.5 1.35 1.35 1.35 2.0 4.5 6.0 4.5 V OH VOL High Level Output Voltage (TP) (for HC7292 HC7294 only) Low Level Output Voltage (Q) 6.0 2.0 Low Level Output Voltage (TP) ICC Input Leakage Current Quiescent Supply Current IO=-5.2 mA 6.0 4.5 6.0 IO=-1.3 mA 2.0 4.5 6.0 2.0 4.5 6.0 4.5 6.0 II VI = IO=-20 µA VIH or V IL IO=-4.0 mA VI = IO=-20 µA VIH or V IL IO=-1.0 mA 4.5 4.5 6.0 VOL 1.8 6.0 6.0 1.8 V 1.8 1.9 2.0 1.9 1.9 4.4 5.9 4.5 6.0 4.4 5.9 4.4 5.9 4.18 4.31 4.13 4.10 5.68 1.9 5.8 2.0 5.63 1.9 5.60 1.9 4.4 4.5 4.4 4.4 5.9 4.18 6.0 4.31 5.9 4.13 5.9 4.10 5.68 5.8 5.63 Unit V 2.0 6.0 V OH -40 to 85 oC -55 to 125 oC 74HC 54HC Min. Max. Min. Max. V V 5.60 0.0 0.0 0.1 0.1 0.1 0.1 0.1 0.1 0.0 0.1 0.1 0.1 0.17 0.18 0.26 0.26 0.33 0.33 0.40 0.40 0.0 0.0 0.1 0.1 0.1 0.1 0.1 0.1 0.0 0.1 0.1 0.1 0.17 0.18 0.26 0.26 0.33 0.33 0.40 0.40 VI = VCC or GND ±0.1 ±1 ±1 µA VI = VCC or GND 4 40 80 µA VI = IO= 20 µA VIH or V IL IO= 4.0 mA IO= 5.2 mA VI = IO= 20 µA VIH or V IL IO= 1.0 mA IO= 1.3 mA V V 7/14 M54/M74HC292/7292/294/7294 AC ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = tf = 6 ns) Test Conditions o Symbol Parameter VCC (V) tTLH tTHL Output Transition Time (Q) tTLH tTHL Output Transition Time (TP) tPLH tPHL Propagation Delay Time (CK - Q) tPLH tPHL Propagation Delay Time (CK - Q) tPHL Propagation Delay Time (CLR - Q) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 tPHL fMAX fMAX Propagation Delay Time (CLR - Q) Maximum Clock Frequency Maximum Clock Frequency tW(H) tW(L) Minimum Pulse Width (CLOCK) tW(L) Minimum Pulse Width (CLEAR) tW(L) tREM tREM CIN CPD (*) Minimum Pulse Width (CLEAR) Minimum Removal Time Minimum Removal Time Input Capacitance Power Dissipation Capacitance for HC292/7292 for HC294/7294 for HC292/7292 for HC294/7294 for HC292/7292 for HC294/7294 for HC292/7292 for HC294/7294 for HC292/7292 for HC294/7294 for HC292/7292 for HC294/7294 TA = 25 C 54HC and 74HC Min. Typ. Max. 30 75 8 15 7 13 116 225 29 45 25 38 160 350 46 70 39 60 145 330 43 66 37 56 130 320 42 64 36 54 110 260 34 52 29 44 5.0 21 27 64 32 75 6.0 20 32 64 38 75 40 75 8 15 7 13 48 125 12 25 10 21 40 100 10 20 9 17 5 5 5 0 0 0 5 10 21 23 Value -40 to 85 oC -55 to 125 oC 74HC 54HC Min. Max. Min. Max. 95 110 19 22 16 19 280 340 56 68 48 57 440 ns 88 105 75 90 415 83 15 71 84 400 210 80 100 68 81 325 390 65 78 55 66 4 3.4 22 18 26 21 5 4 26 21 31 25 95 110 19 22 16 20 155 190 31 38 26 32 125 150 25 30 21 26 5 5 5 5 5 5 0 0 0 0 0 0 10 Unit ns ns ns ns ns MHz MHz ns ns ns ns ns pF pF (*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD •VCC •fIN + ICC 8/14 M54/M74HC292/7292/294/7294 SWITCHING CHARACTERISTICS TEST WAVEFORM TEST CIRCUIT ICC (Opr.) HC292/HC7292 HC294/HC7294 INPUT TRANSITION TIME IS THE SAME AS THAT IN CASE OF SWITCHING CHARACTERISTICS TEST. 9/14 M54/M74HC292/7292/294/7294 Plastic DIP16 (0.25) MECHANICAL DATA mm DIM. MIN. a1 0.51 B 0.77 TYP. inch MAX. MIN. TYP. MAX. 0.020 1.65 0.030 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 17.78 0.700 F 7.1 0.280 I 5.1 0.201 L Z 3.3 0.130 1.27 0.050 P001C 10/14 M54/M74HC292/7292/294/7294 Ceramic DIP16/1 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 20 0.787 B 7 0.276 D E 3.3 0.130 0.38 e3 0.015 17.78 0.700 F 2.29 2.79 0.090 0.110 G 0.4 0.55 0.016 0.022 H 1.17 1.52 0.046 0.060 L 0.22 0.31 0.009 0.012 M 0.51 1.27 0.020 0.050 N P Q 10.3 7.8 8.05 5.08 0.406 0.307 0.317 0.200 P053D 11/14 M54/M74HC292/7292/294/7294 SO16 (Narrow) MECHANICAL DATA mm DIM. MIN. TYP. A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.004 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45° (typ.) D 9.8 E 5.8 10 0.385 6.2 0.228 0.393 0.244 e 1.27 0.050 e3 8.89 0.350 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.62 0.024 8° (max.) P013H 12/14 M54/M74HC292/7292/294/7294 PLCC20 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 9.78 10.03 0.385 0.395 B 8.89 9.04 0.350 0.356 D 4.2 4.57 0.165 0.180 d1 2.54 0.100 d2 0.56 0.022 E 7.37 8.38 0.290 0.330 e 1.27 0.050 e3 5.08 0.200 F 0.38 0.015 G 0.101 0.004 M 1.27 0.050 M1 1.14 0.045 P027A 13/14 M54/M74HC292/7292/294/7294 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express written approval of SGS-THOMSON Microelectonics. 1994 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A 14/14