EL5156, EL5157, EL5256, EL5257 ® Data Sheet September 13, 2007 FN7386.5 <1mV Voltage Offset, 600MHz Amplifiers Features The EL5156, EL5157, EL5256, and EL5257 are 600MHz bandwidth -3dB voltage mode feedback amplifiers with DC accuracy of <0.01%, 1mV offsets and 40kV/V open loop gains. These amplifiers are ideally suited for applications ranging from precision measurement instrumentation to high speed video and monitor applications demanding the very highest linearity at very high frequency. Capable of operating with as little as 6.0mA of current from a single supply ranging from 5V to 12V and dual supplies ranging from ±2.5V to ±5.0V, these amplifiers are also well suited for handheld, portable and battery-powered equipment. With their capability to output as much as 140mA, any member of this family is comfortable with demanding load conditions. • 600MHz -3dB bandwidth, 240MHz 0.1dB bandwidth Single amplifiers are available in SOT-23 packages and duals in a 10 Ld MSOP package for applications where board space is critical. Additionally, singles and duals are available in the industry-standard 8 Ld SOIC package. All parts operate over the industrial temperature range of -40°C to +85°C. • 700V/µs slew rate • <1mV input offset • Very high open loop gains 92dB • Low supply current = 6mA • 140mA output current • Single supplies from 5V to 12V • Dual supplies from ±2.5V to ±5V • Fast disable on the EL5156 and EL5256 • Low cost • Pb-free available (RoHS compliant) Applications • Imaging • Instrumentation • Video • Communications devices Pinouts EL5157 (5 LD SOT-23) TOP VIEW EL5156 (8 LD SOIC) TOP VIEW NC 1 IN- 2 IN+ 3 + VS- 4 8 CE OUT 1 7 VS+ VS- 2 6 OUT IN+ 3 INA+ 1 4 IN- EL5257 (8 LD SOIC) TOP VIEW 10 INA- + VS- 3 CEB 4 + - 5 NC EL5256 (10 LD MSOP) TOP VIEW CEA 2 5 VS+ + - OUTA 1 9 OUTA INA- 2 8 VS+ INA+ 3 7 OUTB VS- 4 8 VS+ 7 OUTB + 6 INB+ 5 INB+ 6 INB- INB+ 5 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2004, 2006, 2007. All Rights Reserved. All other trademarks mentioned are the property of their respective owners. EL5156, EL5157, EL5256, EL5257 Ordering Information PART NUMBER PART MARKING EL5156IS 5156IS PACKAGE 8 Ld SOIC (150 mil) PKG. DWG. # MDP0027 EL5156IS-T7* 5156IS 8 Ld SOIC (150 mil) MDP0027 EL5156IS-T13* 5156IS 8 Ld SOIC (150 mil) MDP0027 EL5156ISZ (Note) 5156ISZ 8 Ld SOIC (150 mil) (Pb-free) MDP0027 EL5156ISZ-T7* (Note) 5156ISZ 8 Ld SOIC (150 mil) (Pb-free) MDP0027 EL5156ISZ-T13* (Note) 5156ISZ 8 Ld SOIC (150 mil) (Pb-free) MDP0027 EL5157IW-T7* BHAA 5 Ld SOT-23 MDP0038 EL5157IW-T7A* BHAA 5 Ld SOT-23 MDP0038 EL5157IWZ-T7* (Note) BAAM 5 Ld SOT-23 (Pb-free) MDP0038 EL5157IWZ-T7A* (Note) BAAM 5 Ld SOT-23 (Pb-free) MDP0038 EL5256IY BAHAA 10 Ld MSOP (3.0mm) MDP0043 EL5256IY-T7* BAHAA 10 Ld MSOP (3.0mm) MDP0043 EL5256IY-T13* BAHAA 10 Ld MSOP (3.0mm) MDP0043 EL5257IS 5257IS 8 Ld SOIC (150 mil) MDP0027 EL5257IS-T7* 5257IS 8 Ld SOIC (150 mil) MDP0027 EL5257IS-T13* 5257IS 8 Ld SOIC (150 mil) MDP0027 EL5257IY BAJAA 8 Ld MSOP (3.0mm) MDP0043 EL5257IY-T7* BAJAA 8 Ld MSOP (3.0mm) MDP0043 EL5257IY-T13* BAJAA 8 Ld MSOP (3.0mm) MDP0043 *Please refer to TB347 for details on reel specifications. NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 2 FN7386.5 September 13, 2007 EL5156, EL5157, EL5256, EL5257 Absolute Maximum Ratings (TA = +25°C) Thermal Information Supply Voltage between VS and VS- . . . . . . . . . . . . . . . . . . . . 13.2V Maximum Slewrate from VS+ and VS- . . . . . . . . . . . . . . . . . . . 1V/µs Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . 50mA Current into IN+, IN-, CE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA Pin Voltages . . . . . . . . . . . . . . . . . . . . . . . . . GND -0.5V to VS +0.5V Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +125°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA Electrical Specifications VS+ = +5V, VS- = -5V, CE = +5V, RF = RG = 562Ω, RL = 150Ω, TA = +25°C, Unless Otherwise Specified. PARAMETER DESCRIPTION CONDITIONS MIN (Note 1) TYP MAX (Note 1) UNIT AC PERFORMANCE BW -3dB Bandwidth AV = +1, RL = 500Ω, CL = 4.7pF 600 MHz AV = +2, RL = 150Ω 180 MHz GBWP Gain Bandwidth Product RL = 150Ω 210 MHz BW1 0.1dB Bandwidth AV = +2 70 MHz SR Slew Rate VO = -3.2V to +3.2V, AV = +2, RL = 150Ω 640 V/µs VO = -3.2V to +3.2V, AV = +1, RL = 500Ω 700 V/µs 15 ns 500 tS 0.1% Settling Time AV = +1 dG Differential Gain Error AV = +2, RL = 150Ω 0.005 % dP Differential Phase Error AV = +2, RL = 150Ω 0.04 ° VN Input Referred Voltage Noise 12 nV/√Hz IN Input Referred Current Noise 5.5 pA/√Hz DC PERFORMANCE VOS Offset Voltage -1 TCVOS Input Offset Voltage Temperature Coefficient Measured from TMIN to TMAX AVOL Open Loop Gain VO is from -2.5V to 2.5V 10 0.5 1 mV -3 µV/°C 40 kV/V INPUT CHARACTERISTICS CMIR Common Mode Input Range Guaranteed by CMRR test CMRR Common Mode Rejection Ratio VCM = 2.5V to -2.5V 80 108 IB Input Bias Current EL5156 and EL5157 -1 -0.4 +1 µA EL5256 and EL5257 -600 -200 +600 nA -250 100 +250 nA 10 25 MΩ 1 pF IOS Input Offset Current RIN Input Resistance CIN Input Capacitance -2.5 +2.5 V dB OUTPUT CHARACTERISTICS VOUT IOUT Output Voltage Swing Peak Output Current 3 RL = 150Ω to GND ±3.4 ±3.6 V RL = 500Ω to GND ±3.6 ±3.8 V RL = 10Ω to GND ±80 ±140 mA FN7386.5 September 13, 2007 EL5156, EL5157, EL5256, EL5257 Electrical Specifications VS+ = +5V, VS- = -5V, CE = +5V, RF = RG = 562Ω, RL = 150Ω, TA = +25°C, Unless Otherwise Specified. (Continued) PARAMETER DESCRIPTION MIN (Note 1) CONDITIONS TYP MAX (Note 1) UNIT ENABLE (EL5156 and EL5256 ONLY) tEN Enable Time 200 ns tDIS Disable Time 300 ns IIHCE CE Pin Input High Current CE = VS+ 13 25 µA IILCE CE Pin Input Low Current CE = VS- 0 1 µA VIHCE CE Input High Voltage for Power-down VILCE CE Input Low Voltage for Power-up VS+ - 1 V VS+ - 3 V SUPPLY ISON Supply Current - Enabled (per amplifier) No load, VIN = 0V, CE = +5V ISOFF Supply Current - Disabled (per amplifier) No load, VIN = 0V, CE = 5V PSRR Power Supply Rejection Ratio DC, VS = ±3.0V to ±6.0V 5.1 6.0 6.9 mA 5 13 25 µA 75 90 dB NOTE: 1. Parts are 100% tested at +25°C. Over-temperature limits established by characterization and are not production tested. Typical Performance Curves 4 135 RL = 150Ω CL = 4.7pF 2 45 AV = +2 AV = +1 0 -2 AV = +10 AV = +5 -4 -6 100k 1M AV = +5 AV = +2 PHASE (°) NORMALIZED GAIN (dB) RL = 150Ω CL = 4.7pF -45 AV = +10 -135 -225 10M 100M -315 100k 1G 1M FREQUENCY (Hz) FIGURE 1. SMALL SIGNAL FREQUENCY RESPONSE - GAIN 1G 5 VS = ±5V AV = +2 RF = RG = 562Ω AV = +1 RL = 500Ω 3 RL = 500Ω 0 GAIN (dB) NORMALIZED GAIN (dB) 100M FIGURE 2. SMALL SIGNAL FREQUENCY RESPONSE PHASE FOR VARIOUS GAINS 4 2 10M FREQUENCY (Hz) RL = 150Ω -2 RL = 750Ω RL = 50Ω -4 -6 100k 1M 10M 100M CL = 10pF CL = 4.7pF 1 -1 CL = 1pF -3 1G FREQUENCY (Hz) FIGURE 3. SMALL SIGNAL FREQUENCY RESPONSE FOR VARIOUS RL 4 CL = 27pF -5 100k 1M 10M 100M 1G FREQUENCY (Hz) FIGURE 4. SMALL SIGNAL FREQUENCY RESPONSE FOR VARIOUS CL FN7386.5 September 13, 2007 EL5156, EL5157, EL5256, EL5257 Typical Performance Curves (Continued) 3 16 AV = +2 RL = 500Ω RF = RG = 500Ω 12 1 CL = 8.2pF -1 AV = +2 RL = 150Ω RF = RG = 562Ω CL = 10pF 8 4 CL = 0pF CL = 4.7pF -3 0 CL = 0pF -5 100k 1M 10M 100M -4 100k 1G 1M FREQUENCY (Hz) 100M 1G FIGURE 6. SMALL SIGNAL FREQUENCY RESPONSE FOR VARIOUS CL 5 5 AV = +5 RL = 500Ω 3 CL = 82pF 1 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 10M FREQUENCY (Hz) FIGURE 5. SMALL SIGNAL FREQUENCY RESPONSE FOR VARIOUS CL CL = 100pF CL = 68pF -1 CL = 22pF -3 -5 100k 1M 10M 100M AV = +1 RL = 500Ω 3 CL = 4.7pF ±3.0V 1 ±2.0V ±4.0V -1 ±5.0V -3 -5 100k 1G 1M FREQUENCY (Hz) 100M 1G FIGURE 8. FREQUENCY RESPONSE vs POWER SUPPLY 5 4 AV = +1 RL = 500Ω 3 CL = 4.7pF NORMALIZED GAIN (dB) AV = +1 1 -1 AV = +2 -3 -5 100k 10M FREQUENCY (Hz) FIGURE 7. SMALL SIGNAL FREQUENCY RESPONSE FOR VARIOUS CL NORMALIZED GAIN (dB) CL = 180pF CL = 100pF CL = 33pF CL = 22pF CL = 10pF GAIN (dB) NORMALIZED GAIN (dB) 5 AV = +5 1M 10M 100M FREQUENCY (Hz) FIGURE 9. EL5256 SMALL SIGNAL FREQUENCY RESPONSE FOR VARIOUS GAINS 5 1G 2 VS = ±5V RF = 620Ω RL = 150Ω AV = -1 0 AV = -2 -2 -4 -6 100k 1M 10M 100M 1G FREQUENCY (Hz) FIGURE 10. SMALL SIGNAL INVERTING FREQUENCY RESPONSE FOR VARIOUS GAINS FN7386.5 September 13, 2007 EL5156, EL5157, EL5256, EL5257 Typical Performance Curves (Continued) 4 5 AV = +1 CL = 4.7pF RL = 500Ω 2 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) AV = +1 CL = 0.2pF RL = 300Ω 0 RL = 150Ω -2 -4 -6 100k 1M 10M 100M 3 RL = 500Ω RL = 200Ω 1 -1 RL = 50Ω -3 RL = 100Ω -5 100k 1G 1M FREQUENCY (Hz) FIGURE 11. SMALL SIGNAL FREQUENCY RESPONSE FOR VARIOUS RL CIN = 12pF CIN = 8.2pF NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 1G 4 AV = +2 RL = 500Ω 3 CL = 4.7pF RF = 500Ω CIN = 4.7pF 1 CIN = 0.2pF -1 CIN = 0pF -3 -5 100k 1M 10M AV = +5 CL = 4.7pF RL = 500Ω RF = 102Ω 2 CIN = 47pF CIN = 22pF -2 CIN = 0pF CIN = 4.7pF -4 -6 100k 100M CIN = 68pF 0 1M FREQUENCY (Hz) 10M 100M FREQUENCY (Hz) FIGURE 13. SMALL SIGNAL FREQUENCY RESPONSE FOR VARIOUS CIN FIGURE 14. SMALL SIGNAL FREQUENCY RESPONSE FOR VARIOUS CIN 6 VS = ±5V AV = +2 RL = 150Ω CL = 4.7pF RF = RG = 1kΩ RF = RG = 350Ω 0 RF = RG = 562Ω -2 RF = RG = 500Ω RF = RG = 250Ω -4 -6 100k 1M 10M 100M 1G FREQUENCY (Hz) FIGURE 15. SMALL SIGNAL FREQUENCY RESPONSE FOR VARIOUS RF AND RG 6 NORMALIZED GAIN (dB) 4 NORMALIZED GAIN (dB) 100M FIGURE 12. EL5256 SMALL SIGNAL FREQUENCY RESPONSE FOR VARIOUS RL 5 2 10M FREQUENCY (Hz) 4 AV = +2 CL = 4.7pF RL = 500Ω RF = RG = 3kΩ RF = RG = 2kΩ RF = RG = 1kΩ 2 0 RF = RG = 500Ω -2 -4 100k RF = RG = 200Ω 1M 10M 100M 1G FREQUENCY (Hz) FIGURE 16. EL5256 SMALL SIGNAL FREQUENCY RESPONSE FOR VARIOUS RF AND RG FN7386.5 September 13, 2007 EL5156, EL5157, EL5256, EL5257 Typical Performance Curves (Continued) 3 5 AV = +2 RL = 200Ω CL = 4.7pF +15dBm 1 -20dBm +10dBm -1 +17dBm +20dBm -3 -5 100k 1M 10M 100M 3 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 5 AV = +1 RL = 500Ω CL = 4.7pF CH1 1 CH2 -1 -3 -5 100k 1G 1M FREQUENCY (Hz) FIGURE 17. LARGE SIGNAL FREQUENCY RESPONSE FOR VARIOUS INPUT AMPLITUDES 1G 700 AV = +5 RL = 500Ω CL = 4.7pF AV = +1, RL = 500Ω, CL = 5pF 600 500 AV = +1, RL = 150Ω BW (MHz) CROSS TALK (10dB) 100M FIGURE 18. CHANNEL TO CHANNEL FREQUENCY RESPONSE 0 -20 10M FREQUENCY (Hz) -40 -60 400 300 AV = +2, RL = 150Ω 200 -80 100 -100 100k 1M 10M 100M 0 4.5 1G 5.5 6.5 7.5 FIGURE 19. EL5256 CROSSTALK vs FREQUENCY CHANNEL A TO B AND B TO A 9.5 10.5 11.5 12.5 FIGURE 20. BANDWIDTH vs SUPPLY VOLTAGE 4 1k VOLTAGE NOISE (nV/√Hz), CURRENT NOISE (pA/√Hz) AV = +5 CL = 4.7pF NORMALIZED GAIN (dB) 8.5 VS (V) FREQUENCY (Hz) 2 RL = 1kΩ 0 RL = 500Ω -2 RL = 100Ω RL = 50Ω -4 -6 100k 1M 10M 100M 1G FREQUENCY (Hz) FIGURE 21. SMALL SIGNAL FREQUENCY RESPONSE FOR VARIOUS RL 7 100 VN 10 IN 1 100k 1M 10M 10M 100M 100M 1G FREQUENCY (Hz) FIGURE 22. VOLTAGE AND CURRENT NOISE vs FREQUENCY FN7386.5 September 13, 2007 EL5156, EL5157, EL5256, EL5257 Typical Performance Curves (Continued) -20 1k AV = +2 RL = 0Ω RG = RF = 400Ω -40 IMPEDANCE (Ω) CMRR (dB) 100 -60 -80 10 1 -100 -120 100 1k 10k 100k 1M 10M 0.01 1k 100M 10k 100k FREQUENCY (Hz) 100M FIGURE 24. OUTPUT IMPEDANCE -10 6.1 VS = ±5V AV = +2 RL = 150Ω 6.0 5.9 5.8 -50 IS (mA) DISABLED ISOLATION (dB) 10M FREQUENCY (Hz) FIGURE 23. CMRR -30 1M -70 IS- 5.7 IS+ 5.6 5.5 -90 5.4 -110 100k 1M 10M 100M 5.3 4.5 1G 5.5 6.5 7.5 FREQUENCY (Hz) FIGURE 25. INPUT TO OUTPUT ISOLATION vs FREQUENCY DISABLE 8.5 9.5 10.5 11.5 VS (V) FIGURE 26. SUPPLY CURRENT vs SUPPLY VOLTAGE 0.8 AV = +2 RL = 500Ω SUPPLY = ±5V ±12.3mA DISABLE 322ns AV = +1 CL = 5pF RL = 500Ω 0.6 PEAKING (dB) ENABLE 192ns 0.7 0.5 0.4 0.3 0.2 0.1 TIME (400ns/DIV) 0 4.5 5.5 6.5 7.5 8.5 9.5 10.5 11.5 12.5 VS (V) FIGURE 27. ENABLE/DISABLE RESPONSE 8 FIGURE 28. PEAKING vs SUPPLY VOLTAGE FN7386.5 September 13, 2007 EL5156, EL5157, EL5256, EL5257 Typical Performance Curves (Continued) AV = +2 RL = 500Ω SUPPLY = ±5V ±12.3mA OUTPUT = 200mVP-P VOUT (40mV/DIV) VOUT (40mV/DIV) AV = +2 RL = 500Ω SUPPLY = ±5V ±12.3mA OUTPUT = 200mVP-P 0 RISE 20% TO 80% Δt = 2.025ns 0 FALL 80% TO 20% Δt = 1.7ns TIME (4ns/DIV) TIME (4ns/DIV) FIGURE 29. SMALL SIGNAL RISE TIME FIGURE 30. SMALL SIGNAL FALL TIME AV = +2 RL = 500Ω SUPPLY = ±5V ±12.3mA OUTPUT = 2.0VP-P VOUT (400mV/DIV) VOUT (400mV/DIV) AV = +2 RL = 500Ω SUPPLY = ±5V ±12.3mA OUTPUT = 2.0VP-P 0 RISE 20% TO 80% Δt = 1.657ns 0 FALL 80% TO 20% Δt = 1.7ns TIME (2ns/DIV) TIME (2ns/DIV) FIGURE 31. LARGE SIGNAL RISE TIME 1.8 FIGURE 32. LARGE SIGNAL FALL TIME JEDEC JESD51-7 HIGH EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD 1.2 JEDEC JESD51-3 LOW EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD POWER DISSIPATION (W) POWER DISSIPATION (W) 1.6 1.4 1.2 1.136W SO8 θJA = +110°C/W 1.0 870mW 0.8 MSOP10 θJA = +115°C/W 0.6 543mW 0.4 SOT23-5 θJA = +230°C/W 0.2 0 1.0 781mW 0.8 SO8 θJA = +160°C/W 0.6 488mW 0.4 486mW SOT23-5 θJA = +256°C/W MSOP10 θJA = +115°C/W 0.2 0 0 25 50 75 85 100 125 150 AMBIENT TEMPERATURE (°C) FIGURE 33. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE 9 0 25 50 75 85 100 125 150 AMBIENT TEMPERATURE (°C) FIGURE 34. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE FN7386.5 September 13, 2007 EL5156, EL5157, EL5256, EL5257 EL5156 Product Description The EL5156, EL5157, EL5256, and EL5257 are wide bandwidth, single or dual supply, low power and low offset voltage feedback operational amplifiers. Both amplifiers are internally compensated for closed loop gain of +1 or greater. Connected in voltage follower mode and driving a 500Ω load, the -3dB bandwidth is about 610MHz. Driving a 150Ω load and a gain of 2, the bandwidth is about 180MHz while maintaining a 600V/µs slew rate. The EL5156 and EL5256 are available with a power-down pin to reduce power to 17µA typically while the amplifier is disabled. Input, Output and Supply Voltage Range The EL5156 and EL5157 families have been designed to operate with supply voltage from 5V to 12V. That means for single supply application, the supply voltage is from 5V to 12V. For split supplies application, the supply voltage is from ±2.5V to ±5V. The amplifiers have an input common mode voltage range from 1.5V above the negative supply (VS- pin) to 1.5V below the positive supply (VS+ pin). If the input signal is outside the above specified range, it will cause the output signal to be distorted. The outputs of the EL5156 and EL5157 families can swing from -4V to 4V for VS = ±5V. As the load resistance becomes lower, the output swing is lower. If the load resistor is 500Ω, the output swing is about -4V at a 4V supply. If the load resistor is 150Ω, the output swing is from -3.5V to 3.5V. Choice of Feedback Resistor and Gain Bandwidth Product For applications that require a gain of +1, no feedback resistor is required. Just short the output pin to the inverting input pin. For gains greater than +1, the feedback resistor forms a pole with the parasitic capacitance at the inverting input. As this pole becomes smaller, the amplifier's phase margin is reduced. This causes ringing in the time domain and peaking in the frequency domain. Therefore, RF can't be very big for optimum performance. If a large value of RF must be used, a small capacitor in the few Pico farad range in parallel with RF can help to reduce the ringing and peaking at the expense of reducing the bandwidth. For gain of +1, RF = 0 is optimum. For the gains other than +1, optimum response is obtained with RF between 500Ω to 750Ω. The EL5156 and EL5157 families have a gain bandwidth product of 210MHz. For gains ≥5, its bandwidth can be predicted by Equation 1: Gain × BW = 210MHz (EQ. 1) Video Performance For good video performance, an amplifier is required to maintain the same output impedance and the same frequency response as DC levels are changed at the output. 10 This is especially difficult when driving a standard video load of 150Ω, because of the change in output current with DC level. The dG and dP for these families are about 0.006% and 0.04%, while driving 150Ω at a gain of 2. Driving high impedance loads would give a similar or better dG and dP performance. Driving Capacitive Loads and Cables The EL5156 and EL5157 families can drive 27pF loads in parallel with 500Ω with less than 5dB of peaking at gain of +1. If less peaking is desired in applications, a small series resistor (usually between 5Ω to 50Ω) can be placed in series with the output to eliminate most peaking. However, this will reduce the gain slightly. If the gain setting is greater than 1, the gain resistor RG can then be chosen to make up for any gain loss which may be created by the additional series resistor at the output. When used as a cable driver, double termination is always recommended for reflection-free performance. For those applications, a back-termination series resistor at the amplifier's output will isolate the amplifier from the cable and allow extensive capacitive drive. However, other applications may have high capacitive loads without a back-termination resistor. Again, a small series resistor at the output can help to reduce peaking. Disable/Power-Down The EL5156 and EL5256 can be disabled and their output placed in a high impedance state. The turn-off time is about 330ns and the turn-on time is about 130ns. When disabled, the amplifier's supply current is reduced to 17µA typically, thereby effectively eliminating the power consumption. The amplifier's power-down can be controlled by standard TTL or CMOS signal levels at the ENABLE pin. The applied logic signal is relative to VS- pin. Letting the ENABLE pin float or applying a signal that is less than 0.8V above VS- will enable the amplifier. The amplifier will be disabled when the signal at ENABLE pin is above VS+ - 1.5V. Output Drive Capability The EL5156 and EL5157 families do not have internal short circuit protection circuitry. They have a typical short circuit current of 95mA and 70mA. If the output is shorted indefinitely, the power dissipation could easily overheat the die or the current could eventually compromise metal integrity. Maximum reliability is maintained if the output current never exceeds ±40mA. This limit is set by the design of the internal metal interconnect. Note that in transient applications, the part is robust. Power Dissipation With the high output drive capability of the EL5152 and EL5153 families, it is possible to exceed the +125°C absolute maximum junction temperature under certain load current conditions. Therefore, it is important to calculate the maximum junction temperature for an application to FN7386.5 September 13, 2007 EL5156, EL5157, EL5256, EL5257 determine if load conditions or package types need to be modified to assure operation of the amplifier in a safe operating area. By setting the two PDMAX equations equal to each other, we can solve the output current and RLOAD to avoid the device overheat. The maximum power dissipation allowed in a package is determined according to Equation 2: Power Supply Bypassing Printed Circuit Board Layout T JMAX – T AMAX PD MAX = --------------------------------------------Θ JA The maximum power dissipation actually produced by an IC is the total quiescent supply current times the total power supply voltage, plus the power in the IC due to the load, or: As with any high frequency device, a good printed circuit board layout is necessary for optimum performance. Lead lengths should be as short as possible. The power supply pin must be well bypassed to reduce the risk of oscillation. For normal single supply operation, where the VS- pin is connected to the ground plane, a single 4.7µF tantalum capacitor in parallel with a 0.1µF ceramic capacitor from VS+ to GND will suffice. This same capacitor combination should be placed at each supply pin to ground if split supplies are to be used. In this case, the VS- pin becomes the negative supply rail. See Figure 37 for a complete tuned power supply bypass methodology. For sourcing: Printed Circuit Board Layout (EQ. 2) Where: TJMAX = Maximum junction temperature TAMAX = Maximum ambient temperature θJA = Thermal resistance of the package n V OUTi ∑ ( VS – VOUTi ) × ---------------R Li PD MAX = V S × I SMAX + (EQ. 3) i=1 For sinking: n ∑ ( VOUTi – VS ) × ILOADi PD MAX = V S × I SMAX + i=1 Where: VS = Supply voltage (EQ. 4) For good AC performance, parasitic capacitance should be kept to a minimum. Use of wire wound resistors should be avoided because of their additional series inductance. Use of sockets should also be avoided if possible. Sockets add parasitic inductance and capacitance that can result in compromised performance. Minimizing parasitic capacitance at the amplifier's inverting input pin is very important. The feedback resistor should be placed very close to the inverting input pin. Strip line design techniques are recommended for the signal traces. ISMAX = Maximum quiescent supply current VOUT = Maximum output voltage of the application RLOAD = Load resistance tied to ground ILOAD = Load current N = number of amplifiers (max = 2) 11 FN7386.5 September 13, 2007 EL5156, EL5157, EL5256, EL5257 Application Circuits Sallen Key High Pass Filter Sallen Key Low Pass Filter A common and easy to implement filter taking advantage of the wide bandwidth, low offset and low power demands of the EL5152. A derivation of the transfer function is provided for convenience (See Figure 35). RB K = 1 + -------RA V2 5V 1 V O = K ⋅ --------------------------------- ⋅ V O R 2 ⋅ C 2S + 1 L1 VO ---------------V1 – Vi VO – Vi K–V -= 0 ------------------ 1 + ----------------1- + -----------------R1 R2 1 ----------C 1S 10µH TUNED POWER BYPASS NETWORK Again this useful filter benefits from the characteristics of the EL5152. The transfer function is very similar to the low pass so only the results are presented (See Figure 36). R5 C3 1kΩ C5 1nF K H 〈 s〉 = ---------------------------------------------------------------------------------------------------------------------------------------------R 1 C 1 R 2 C 2S 2 + ( ( 1 – K )R 1 C 1 + R 1 C 2 + R 21 C 2 )s + 1 1nF C1 1 H 〈 jw〉 = -----------------------------------------------------------------------------------------------------------------------------------------------2 1 – w R 1 C 1 R 2 C 2 + jw ( ( 1 – K )R 1 C 1 + R 1 C 2 + R 2 C 2 ) 1nF R1 V1 1kΩ R2 1kΩ C2 1nF + V+ - V- VOUT R7 1kΩ 1 wo = ----------------------------------R1 C1 R2 C2 RB 1kΩ RA 1kΩ TUNED POWER BYPASS NETWORK Holp = K C5 1nF R6 C4 1 Q = -------------------------------------------------------------------------------------------R1 C2 R2 C2 R1 C1 - + -------------〈 1 – K〉 --------------- + -------------R2 C2 R2 C1 R1 C1 1kΩ 1nF Holp = K L1 10µH V3 5V 1 wo = --------RC 1 Q = ------------3–K Equations simplify if we let all components be equal to R = C FIGURE 35. SALLEN KEY LOW PASS FILTER 12 FN7386.5 September 13, 2007 EL5156, EL5157, EL5256, EL5257 Holp = K V2 5V 1 wo = ----------------------------------R1 C1 R2 C2 L1 1 Q = -------------------------------------------------------------------------------------------R1 C2 R2 C2 R1 C1 - + -------------〈 1 – K〉 --------------- + -------------R2 C2 R2 C1 R1 C1 10µH TUNED POWER BYPASS NETWORK R5 C3 1kΩ C5 1nF K Holp = ------------4–K 1nF C1 2 wo = --------RC 1nF R1 V1 1kΩ R2 1kΩ C2 1nF + V+ - V- VOUT 2 Q = ------------4–K R7 1kΩ RB 1kΩ RA 1kΩ C5 TUNED POWER BYPASS NETWORK 1nF R6 C4 1kΩ 1nF L1 10µH Equations simplify if we let V3 5V all components be equal to R = C FIGURE 36. SALLEN KEY HIGH PASS FILTER Differential Output Instrumentation Amplifier The addition of a third amplifier to the conventional three amplifier instrumentation amplifier introduces the benefits of differential signal realization, specifically the advantage of using common mode rejection to remove coupled noise and ground potential errors inherent in remote transmission. This configuration also provides enhanced bandwidth, wider output swing and faster slew rate than conventional three amplifier solutions with only the cost of an additional amplifier and a few resistors. e1 A1 + - R3 R3 A3 R2 + RG R3 R3 R3 R3 A4 R2 A2 e2 + + R3 e o3 = – ( 1 + 2R 2 ⁄ R G ) ( e 1 – e 2 ) eo3 + REF eo eo4 R3 e o4 = ( 1 + 2R 2 ⁄ R G ) ( e 1 – e 2 ) e o = – 2 ( 1 + 2R 2 ⁄ R G ) ( e 1 – e 2 ) 2f C1, 2 BW = -----------------A Di 13 A Di = – 2 ( 1 + 2R 2 ⁄ R G ) FN7386.5 September 13, 2007 EL5156, EL5157, EL5256, EL5257 Strain Gauge The strain gauge is an ideal application to take advantage of the moderate bandwidth and high accuracy of the EL5152. The operation of the circuit is very straightforward. As the strain variable component resistor in the balanced bridge is subjected to increasing strain, its resistance changes, resulting in an imbalance in the bridge. A voltage variation from the referenced high accuracy source is generated and translated to the difference amplifier through the buffer stage. This voltage difference as a function of the strain is converted into an output voltage. FIGURE 37. STRAIN GAUGE OPERATIONAL CIRCUIT 14 FN7386.5 September 13, 2007 EL5156, EL5157, EL5256, EL5257 Small Outline Package Family (SO) A D h X 45° (N/2)+1 N A PIN #1 I.D. MARK E1 E c SEE DETAIL “X” 1 (N/2) B L1 0.010 M C A B e H C A2 GAUGE PLANE SEATING PLANE A1 0.004 C 0.010 M C A B L b 0.010 4° ±4° DETAIL X MDP0027 SMALL OUTLINE PACKAGE FAMILY (SO) INCHES SYMBOL SO-14 SO16 (0.300”) (SOL-16) SO20 (SOL-20) SO24 (SOL-24) SO28 (SOL-28) TOLERANCE NOTES A 0.068 0.068 0.068 0.104 0.104 0.104 0.104 MAX - A1 0.006 0.006 0.006 0.007 0.007 0.007 0.007 ±0.003 - A2 0.057 0.057 0.057 0.092 0.092 0.092 0.092 ±0.002 - b 0.017 0.017 0.017 0.017 0.017 0.017 0.017 ±0.003 - c 0.009 0.009 0.009 0.011 0.011 0.011 0.011 ±0.001 - D 0.193 0.341 0.390 0.406 0.504 0.606 0.704 ±0.004 1, 3 E 0.236 0.236 0.236 0.406 0.406 0.406 0.406 ±0.008 - E1 0.154 0.154 0.154 0.295 0.295 0.295 0.295 ±0.004 2, 3 e 0.050 0.050 0.050 0.050 0.050 0.050 0.050 Basic - L 0.025 0.025 0.025 0.030 0.030 0.030 0.030 ±0.009 - L1 0.041 0.041 0.041 0.056 0.056 0.056 0.056 Basic - h 0.013 0.013 0.013 0.020 0.020 0.020 0.020 Reference - 16 20 24 28 Reference - N SO-8 SO16 (0.150”) 8 14 16 Rev. M 2/07 NOTES: 1. Plastic or metal protrusions of 0.006” maximum per side are not included. 2. Plastic interlead protrusions of 0.010” maximum per side are not included. 3. Dimensions “D” and “E1” are measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994 15 FN7386.5 September 13, 2007 EL5156, EL5157, EL5256, EL5257 SOT-23 Package Family MDP0038 e1 D SOT-23 PACKAGE FAMILY A MILLIMETERS 6 N SYMBOL 4 E1 2 E 3 0.15 C D 1 2X 2 3 0.20 C 5 2X e 0.20 M C A-B D B b NX 0.15 C A-B 1 3 SOT23-5 SOT23-6 A 1.45 1.45 MAX A1 0.10 0.10 ±0.05 A2 1.14 1.14 ±0.15 b 0.40 0.40 ±0.05 c 0.14 0.14 ±0.06 D 2.90 2.90 Basic E 2.80 2.80 Basic E1 1.60 1.60 Basic e 0.95 0.95 Basic e1 1.90 1.90 Basic L 0.45 0.45 ±0.10 L1 0.60 0.60 Reference N 5 6 Reference D 2X TOLERANCE Rev. F 2/07 NOTES: C A2 2. Plastic interlead protrusions of 0.25mm maximum per side are not included. SEATING PLANE A1 0.10 C 1. Plastic or metal protrusions of 0.25mm maximum per side are not included. 3. This dimension is measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994. NX 5. Index area - Pin #1 I.D. will be located within the indicated zone (SOT23-6 only). (L1) 6. SOT23-5 version has no center lead (shown as a dashed line). H A GAUGE PLANE c L 16 0.25 0° +3° -0° FN7386.5 September 13, 2007 EL5156, EL5157, EL5256, EL5257 Mini SO Package Family (MSOP) 0.25 M C A B D MINI SO PACKAGE FAMILY (N/2)+1 N E MDP0043 A E1 MILLIMETERS PIN #1 I.D. 1 B (N/2) e H C SEATING PLANE 0.10 C N LEADS SYMBOL MSOP8 MSOP10 TOLERANCE NOTES A 1.10 1.10 Max. - A1 0.10 0.10 ±0.05 - A2 0.86 0.86 ±0.09 - b 0.33 0.23 +0.07/-0.08 - c 0.18 0.18 ±0.05 - D 3.00 3.00 ±0.10 1, 3 E 4.90 4.90 ±0.15 - E1 3.00 3.00 ±0.10 2, 3 e 0.65 0.50 Basic - L 0.55 0.55 ±0.15 - L1 0.95 0.95 Basic - N 8 10 Reference - 0.08 M C A B b Rev. D 2/07 NOTES: 1. Plastic or metal protrusions of 0.15mm maximum per side are not included. L1 2. Plastic interlead protrusions of 0.25mm maximum per side are not included. A 3. Dimensions “D” and “E1” are measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994. c SEE DETAIL "X" A2 GAUGE PLANE L A1 0.25 3° ±3° DETAIL X All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 17 FN7386.5 September 13, 2007