HVP5 RECTRON THRU SEMICONDUCTOR TECHNICAL SPECIFICATION HVP16 HIGH VOLTAGE ASSEMBLIED RECTIFIER VOLTAGE RANGE 5000 to 16000 Volts CURRENT 0.75 Amperes FEATURES * * * * * * Low cost Low leakage Isolated case Surge overload rating - 50 amperes peak Mounting position: Any Low forward voltage drop HVP .256 (6.5) .177 (4.5) .161 (4.1) MECHANICAL DATA * Epoxy: Device has UL flammability classification 94V-O .244 (6.2) .772 (19.6) .732 (18.6) .035 (0.9) .030 (0.8) .142 (3.6) .126 (3.2) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS 2.520 (64.0) .331 (8.4) 2.500 (63.5) .315 (8.0) 1.673 (42.5) 1.634 (41.5) 1.594 (40.5) 1.555 (39.5) .441 (11.2) .772 (19.6) .732 (18.6) Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. 1.295 (7.5) 1.256 (6.5) 3.012 (76.5) 2.972 (75.5) For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) MAXIMUM RATINGS (At T A = 25 oC unless otherwise noted) SYMBOL HVP5 HVP8 HVP10 HVP12 HVP14 HVP15 HVP16 UNITS Maximum Recurrent Peak Reverse Voltage VRRM 5 8 10 12 14 15 16 K Volts Maximum RMS Voltage VRMS 3.5 5.6 7.0 8.4 9.8 10.5 11.2 K Volts Maximum DC Blocking Voltage VDC 5 8 10 12 14 15 16 K Volts RATINGS Maximum Average Forward Rectified Current at T A = 50 oC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Operating and Storage Temperature Range IO 750 mAmps I FSM 50 Amps T J, T STG -20 to + 135 0 C ELECTRICAL CHARACTERISTICS (At TA = 25oC unless otherwise noted) SYMBOL HVP5 Maximum Instantaneous Forward Voltage at 0.35A DC CHARACTERISTICS VF 8.0 Maximum DC Reverse Current at Rated DC Blocking Voltage IR NOTES: Enough heat sink must be considered in application. HVP8 HVP10 HVP12 HVP14 14.0 5.0 HVP15 HVP16 UNITS Volts uAmps 2001-6 RATING AND CHARACTERISTIC CURVES ( HVP5 THRU HVP16 ) FIG. 2 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 750 PEAK FORWARD SURGE CURRENT, (A) AVERAGE FORWARD CURRENT, (mA) FIG. 1 - TYPICAL FORWARD CURRENT DERATING CURVE Single Phase Half Wave 60Hz Inductive or Resistive Load 600 450 300 150 0 0 50 100 150 AMBIENT TEMPERATURE, ( 60 50 8.3ms Single Half Sine-Wave (JEDEC Method) 40 30 20 10 0 1 175 10 100 NUMBER OF CYCLES AT 60Hz ) FIG. 4 - TYPICAL INSTANTANEOUS FORWARD FIG. 3 - TYPICAL REVERSE CHARACTERISTICS .6 .4 .2 .1 TJ = 25 .06 .04 .02 .01 6 8 P1 HV 0~ P1 HV 1.0 100 VP 2 ~H 4 P5 6 1000 HV INSTANTANEOUS FORWARD CURRENT, (mA) INSTANTANEOUS REVERSE CURRENT, (uA) CHARACTERISTICS 10 10 TJ = 25 Pulse Width = 300us 1% Duty Cycle 1.0 0.1 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) 4 5 6 7 8 9 10 11 12 INSTANTANEOUS FORWARD VOLTAGE, (V) RECTRON