TI LM211QDR Differential comparators with strobe Datasheet

LM111, LM211, LM311
DIFFERENTIAL COMPARATORS WITH STROBES
SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003
Fast Response Times
Strobe Capability
Maximum Input Bias Current . . . 300 nA
Maximum Input Offset Current . . . 70 nA
D
D
Can Operate From Single 5-V Supply
Available in Q-Temp Automotive
– High-Reliability Automotive Applications
– Configuration Control/Print Support
– Qualification to Automotive Standards
LM111 . . . JG PACKAGE
LM211 . . . D, P, OR PW PACKAGE
LM311 . . . D, P, PS, OR PW PACKAGE
(TOP VIEW)
8
2
7
3
6
4
5
VCC+
COL OUT
BAL/STRB
BALANCE
NC
EMIT OUT
NC
VCC+
NC
1
NC
IN+
NC
IN–
NC
4
3 2 1 20 19
18
5
17
6
16
7
15
8
14
9 10 11 12 13
NC
VCC–
EMIT OUT
IN+
IN–
VCC–
LM111 . . . FK PACKAGE
(TOP VIEW)
NC
COL OUT
NC
BAL/STRB
NC
NC
BALANCE
NC
D
D
D
D
NC – No internal connection
description/ordering information
The LM111, LM211, and LM311 are single high-speed voltage comparators. These devices are designed to
operate from a wide range of power-supply voltages, including ±15-V supplies for operational amplifiers and
5-V supplies for logic systems. The output levels are compatible with most TTL and MOS circuits. These
comparators are capable of driving lamps or relays and switching voltages up to 50 V at 50 mA. All inputs and
outputs can be isolated from system ground. The outputs can drive loads referenced to ground, VCC+ or VCC–.
Offset balancing and strobe capabilities are available, and the outputs can be wire-OR connected. If the strobe
is low, the output is in the off state, regardless of the differential input.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2003, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
On products compliant to MIL-PRF-38535, all parameters are tested
unless otherwise noted. On all other products, production
processing does not necessarily include testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
LM111, LM211, LM311
DIFFERENTIAL COMPARATORS WITH STROBES
SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003
description/ordering information
ORDERING INFORMATION
TA
VIO max
AT 25°C
PACKAGE†
PDIP (P)
Tube of 50
LM311P
Tube of 75
LM311D
Reel of 2500
LM311DR
Reel of 2000
LM311PSR
Reel of 150
LM311PW
Tube of 2000
LM311PWR
Tube of 50
LM211P
Tube of 75
LM211D
Reel of 2500
LM211DR
Reel of 150
LM211PW
Reel of 2000
LM211PWR
Tube of 75
LM211QD
Reel of 2500
LM211QDR
CDIP (JG)
Tube of 50
LM111JG
LCCC (FK)
Tube of 55
LM111FK
SOIC (D)
–0 C to 70°C
–0°C
70 C
7.5 mV
SOP (PS)
TSSOP (PW)
PDIP (P)
–40°C
85°C
–40 C to 85
C
3 mV
SOIC (D)
TSSOP (PW)
–40°C to 125°C
3 mV
–55°C to 125°C
3 mV
ORDERABLE
PART NUMBER
SOIC (D)
TOP-SIDE
MARKING
LM311P
LM311
L311
L311
LM211P
LM211
L211
LM211Q
LM111JG
LM111FK
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
functional block diagram
BALANCE
BAL/STRB
2
IN+
+
COL OUT
IN–
–
EMIT OUT
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
LM111, LM211, LM311
DIFFERENTIAL COMPARATORS WITH STROBES
SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003
schematic
Component Count
Resistors
Diodes
EPI FET
Transistors
BAL/STRB BALANCE
450 Ω
450 Ω
20
2
1
22
VCC+
2.4
kΩ
750 Ω
2.4
kΩ
600 Ω
70 Ω
1.2 kΩ
IN+
1.2 kΩ
4 kΩ
COL OUT
IN–
400 Ω
130 Ω
60 Ω
450 Ω
250 Ω
600 Ω
200 Ω
2 kΩ
4Ω
EMIT OUT
VCC–
All resistor values shown are nominal.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
LM111, LM211, LM311
DIFFERENTIAL COMPARATORS WITH STROBES
SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage: VCC+ (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V
VCC– (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –18 V
VCC+ – VCC– . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 V
Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±30 V
Input voltage, VI (either input, see Notes 1 and 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±15 V
Voltage from emitter output to VCC– . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 V
Voltage from collector output to VCC–: LM111 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 V
LM211 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 V
LM211Q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 V
LM311 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 V
Duration of output short circuit (see Note 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 s
Package thermal impedance, θJA (see Notes 5 and 6): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97°C/W
P package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85°C/W
PS package . . . . . . . . . . . . . . . . . . . . . . . . . . . 95°C/W
PW package . . . . . . . . . . . . . . . . . . . . . . . . . 149°C/W
Package thermal impedance, θJC (see Notes 7 and 8): FK package . . . . . . . . . . . . . . . . . . . . . . . . . 5.61°C/W
JG package . . . . . . . . . . . . . . . . . . . . . . . . . 14.5°C/W
Operating virtual junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: J or JG package . . . . . . . . . . . . . . . . 300°C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: D, P, PS, or PW package . . . . . . . . 260°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, unless otherwise noted, are with respect to the midpoint between VCC+ and VCC–.
2. Differential voltages are at IN+ with respect to IN–.
3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or ±15 V, whichever is less.
4. The output may be shorted to ground or either power supply.
5. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable
ambient temperature is PD = (TJ(max) – TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
6. The package thermal impedance is calculated in accordance with JESD 51-7.
7. Maximum power dissipation is a function of TJ(max), θJC, and TC. The maximum allowable power dissipation at any allowable case
temperature is PD = (TJ(max) – TC)/θJC. Operating at the absolute maximum TJ of 150°C can affect reliability.
8. The package thermal impedance is calculated in accordance with MIL-STD-883.
recommended operating conditions
VCC+ – VCC–
VI
TA
MIN
MAX
3.5
30
V
VCC–+0.5
–55
VCC+–1.5
125
V
LM111
LM211
–40
85
LM211Q
–40
125
0
70
Supply voltage
Input voltage (|VCC±| ≤ 15 V)
Operating free-air temperature range
LM311
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
UNIT
C
°C
LM111, LM211, LM311
DIFFERENTIAL COMPARATORS WITH STROBES
SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003
electrical characteristics at specified free-air temperature, VCC± = ±15 V (unless otherwise noted)
PARAMETER
TA†
TEST CONDITIONS
25°C
VIO
Input offset voltage
See Note 6
IIO
Input offset current
See Note 6
IIB
Input bias current
VO = 1 V to 14 V
IIL(S)
Low-level
strobe current
(see Note 7)
V(strobe) = 0.3 V,
VICR
Common-mode
input voltage range
AVD
Large-signal
differential voltage
amplification
IOH
High-level
(collector)
output leakage
current
0.7
Full range
25°C
4
75
Full range
RL = 1 kΩ
25°C
I(strobe) = –3 mA,
VID = 5 mV
VOH = 35 V,
25°C
VID = 5 mV,
VOH = 35 V
VID = –5 mV
25°C
VID = –10 mV
25°C
VCC+ = 4.5 V,
VCC– = 0,
IOL = 8 mA
VID = –6 mV
Full range
VID = –10 mV
Full range
3
TYP‡
MAX
2
7.5
10
10
6
50
70
100
100
150
25°C
VO = 5 V to 35 V,
MIN
UNIT
20
25°C
VID ≤ –10 mV
LM311
4
Full range
Full range
IOL = 50 mA
LM111
LM211
LM211Q
MIN TYP‡ MAX
300
–3
–3
13
to
–14.5
13.8
to
–14.7
13
to
–14.5
13.8
to
–14.7
40
200
40
200
0.2
Full range
25°C
0.75
VOL
Low-level
(collector-to-emitter)
output voltage
ICC+
Supply current
from VCC+,
output low
VID = –10 mV,
No load
25°C
5.1
ICC–
Supply current
from VCC–,
output high
VID = 10 mV,
No load
25°C
–4.1
0.23
250
mV
nA
nA
mA
V
V/mV
10
nA
0.5
µA
0.2
50
0.75
1.5
nA
1.5
V
0.4
0.23
0.4
6
5.1
7.5
mA
–5
–4.1
–5
mA
† Unless otherwise noted, all characteristics are measured with BALANCE and BAL/STRB open and EMIT OUT grounded.
Full range for LM111 is –55°C to 125°C, for LM211 is –40°C to 85°C, for LM211Q is –40°C to 125°C, and for LM311 is 0°C to 70°C.
‡ All typical values are at TA = 25°C.
NOTES: 9. The offset voltages and offset currents given are the maximum values required to drive the collector output up to 14 V or down to
1 V with a pullup resistor of 7.5 kΩ to VCC+. These parameters actually define an error band and take into account the worst-case
effects of voltage gain and input impedance.
10. The strobe should not be shorted to ground; it should be current driven at –3 mA to –5 mA (see Figures 13 and 27).
switching characteristics, VCC± = ±15 V, TA = 25°C
PARAMETER
LM111
LM211
LM211Q
LM311
TEST CONDITIONS
UNIT
TYP
Response time, low-to-high-level output
Response time, high-to-low-level output
RC = 500 Ω to 5 V,
CL = 5 pF,
See Note 8
115
ns
165
ns
NOTE 11: The response time specified is for a 100-mV input step with 5-mV overdrive and is the interval between the input step function and the
instant when the output crosses 1.4 V.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
LM111, LM211, LM311
DIFFERENTIAL COMPARATORS WITH STROBES
SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003
TYPICAL CHARACTERISTICS†
INPUT OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
20
500
VCC± = ±15 V
VO = 1 V to 14 V
See Note A
18
450
16
14
LM111
LM211
LM311
12
10
Condition 1
Condition 2
8
6
LM311
4
0
–60 –40 –20
0
20
VCC± = ±15 V
VO = 1 V to 14 V
See Note A
LM311
400
350
300
250
LM111
LM211
Condition 2
200
150
LM311
Condition 1
100
LM111
LM211
2
I IB – Input Bias Current – nA
I IO – Input Offset Current – nA
INPUT BIAS CURRENT
vs
FREE-AIR TEMPERATURE
50
40
60
80 100 120 140
LM111
LM211
0
–60 –40 –20
TA – Free-Air Temperature – °C
NOTE A: Condition 1 is with BALANCE and BAL/STRB open.
Condition 2 is with BALANCE and BAL/STRB connected
to VCC+.
0
20
40
60
80 100 120 140
TA – Free-Air Temperature – °C
NOTE A: Condition 1 is with BALANCE and BAL/STRB open.
Condition 2 is with BALANCE and BAL/STRB connected
to VCC+.
Figure 1
Figure 2
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
LM111, LM211, LM311
DIFFERENTIAL COMPARATORS WITH STROBES
SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003
TYPICAL CHARACTERISTICS†
VI = 50 V (LM111, LM211)
40 V (LM311)
VCC+ = 30 V
1 kΩ
VOLTAGE TRANSFER CHARACTERISTICS
60
50
VCC+ = 30 V
VCC– = 0
TA = 25°C
Output
VID
LM111
LM211
VO – Output Voltage – V
VCC–
LM311
40
30
Emitter Output
RL = 600 Ω
COLLECTOR OUTPUT TRANSFER CHARACTERISTIC
TEST CIRCUIT FOR FIGURE 3
Collector
Output
RL = 1 kΩ
VCC+ = 30 V
20
VID
10
Output
600 Ω
0
–1
VCC–
–0.5
0
0.5
1
VID – Differential Input Voltage – mV
EMITTER OUTPUT TRANSFER CHARACTERISTIC
TEST CIRCUIT FOR FIGURE 3
Figure 3
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
LM111, LM211, LM311
DIFFERENTIAL COMPARATORS WITH STROBES
SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003
TYPICAL CHARACTERISTICS
Differential
Input Voltage
OUTPUT RESPONSE FOR
VARIOUS INPUT OVERDRIVES
100 mV
VCC± = ±15 V
RC = 500 Ω to 5 V
TA = 25°C
5
VO – Output Voltage – V
VO – Output Voltage – V
Differential
Input Voltage
OUTPUT RESPONSE FOR
VARIOUS INPUT OVERDRIVES
4
3
2
5 mV
2 mV
20 mV
1
0
0
50
100
150
200
250
300
100 mV
VCC± = ±15 V
RC = 500 Ω to 5 V
TA = 25°C
5
4
20 mV
3
2
0
350
0
50
t – Time – ns
100
150
200
t – Time – ns
Figure 5
Figure 4
VCC+ = 15 V
5V
500 Ω
VO
VID
VCC– = –15 V
TEST CIRCUIT FOR FIGURES 4 AND 5
8
2 mV
5 mV
1
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
250
300
350
LM111, LM211, LM311
DIFFERENTIAL COMPARATORS WITH STROBES
SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003
TYPICAL CHARACTERISTICS
100 mV
VCC± = ±15 V
RE = 2 kΩ to –15 V
TA = 25°C
10
5 mV
5
2 mV
0
–5
–10
–15
0
100 mV
VCC± = ±15 V
RE = 2 kΩ to –15 V
TA = 25°C
15
20 mV
VO – Output Voltage – V
VO – Output Voltage – V
15
OUTPUT RESPONSE FOR
VARIOUS INPUT OVERDRIVES
Differential
Input Voltage
Differential
Input Voltage
OUTPUT RESPONSE FOR
VARIOUS INPUT OVERDRIVES
0.2 0.4
0.6
0.8
1.0
1.2
1.4 1.6
5
2 mV
0
–5
20 mV
–10
–15
1.8
5 mV
10
0
0.2 0.4
0.6
0.8
1.0
1.2
1.4 1.6
1.8
t – Time – ms
t – Time – ms
Figure 6
Figure 7
VCC+ = 15 V
VID
VO
RE = 2 kΩ
VCC– = –15 V
TEST CIRCUIT FOR FIGURES 6 AND 7
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
LM111, LM211, LM311
DIFFERENTIAL COMPARATORS WITH STROBES
SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003
TYPICAL CHARACTERISTICS
OUTPUT CURRENT AND DISSIPATION
vs
OUTPUT VOLTAGE
120
TA = 25°C
No Load
700
600
PO (right scale)
100
500
80
400
60
300
40
200
IO (left scale)
20
100
0
0
5
I CC+ – Positive Supply Current – mA
140
6
800
VCC± = ±15 V
t ≤ 10 s
VID = –10 mV
TA = 25°C
PO – Output Dissipation – mW
I O – Output Current and Dissipation – mA
160
POSITIVE SUPPLY CURRENT
vs
POSITIVE SUPPLY VOLTAGE
0
15
10
5
VID = –10 mV
4
3
VID = 10 mV
2
1
0
0
VO – Output Voltage – V
5
Figure 8
Figure 9
NEGATIVE SUPPLY CURRENT
vs
NEGATIVE SUPPLY VOLTAGE
I CC– – Negative Supply Current – mA
–6
VID = 10 mV or –10 mV
TA = 25°C
No Load
–5
–4
–3
–2
–1
0
0
–5
–10
VCC– – Negative Supply Voltage – V
Figure 10
10
10
VCC+ – Positive Supply Voltage – V
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
–15
15
LM111, LM211, LM311
DIFFERENTIAL COMPARATORS WITH STROBES
SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003
APPLICATION INFORMATION
Figure 11 through Figure 29 show various applications for the LM111, LM211, and LM311 comparators.
VCC+
3 kΩ
3 kΩ
VCC+
20 kΩ
1 kΩ
Square Wave
Output
(fanout to two
Series 54 gates,
or equivalent)
10 kΩ
1200 pF
20 kΩ
BALANCE
39 kΩ
BAL/
STRB
NOTE: If offset balancing is not used,
the BALANCE and BAL/STRB
pins should be shorted together.
Figure 12. Offset Balancing
Figure 11. 100-kHz Free-Running Multivibrator
BAL/STRB
VCC+
TTL
Strobe
2N2222
20 kΩ
1 kΩ
Output
Input
Figure 13. Strobing
NOTE: Do not connect strobe pin
directly to ground, because the
output is turned off whenever
current is pulled from the strobe
pin.
POST OFFICE BOX 655303
VCC–
Figure 14. Zero-Crossing Detector
• DALLAS, TEXAS 75265
11
LM111, LM211, LM311
DIFFERENTIAL COMPARATORS WITH STROBES
SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003
APPLICATION INFORMATION
5V
1 kΩ
82 kΩ
240 kΩ
Input†
Output to TTL
‡
47 kΩ
82 kΩ
† Resistor values shown are for a 0- to 30-V logic swing and a 15-V threshold.
‡ May be added to control speed and reduce susceptibility to noise spikes
Figure 15. TTL Interface With High-Level Logic
VCC+
100 kΩ
5V
4.5 kΩ
2 kΩ
100 kHz
10 pF
2 kΩ
Output
Output
to TTL
100 kΩ
1 kΩ
0.1 µF
50 kΩ
Magnetic
Transducer
Figure 16. Detector for Magnetic Transducer
12
POST OFFICE BOX 655303
Figure 17. 100-kHz Crystal Oscillator
• DALLAS, TEXAS 75265
LM111, LM211, LM311
DIFFERENTIAL COMPARATORS WITH STROBES
SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003
APPLICATION INFORMATION
From D/A Network
VCC+
VCC+
Output
Analog
Input†
22 kΩ
BALANCE
BAL/STRB
0.1 µF
Input
TTL
Strobe
2N2222
Sample
1 kΩ
† Typical input current is 50 pA with inputs strobed off.
Figure 18. Comparator and Solenoid Driver
Figure 19. Strobing Both Input and Output Stages
Simultaneously
VCC+
VCC+ = 5 V
3 kΩ
500 Ω
3.9 kΩ
10 kΩ
3 kΩ
Output
2N3708
BALANCE
BAL/
STRB
Output
to MOS
Input
+
1 kΩ
1.5 µF
10 kΩ
2N2222
VCC– = –10 V
Figure 20. Low-Voltage Adjustable
Reference Supply
POST OFFICE BOX 655303
Figure 21. Zero-Crossing Detector
Driving MOS Logic
• DALLAS, TEXAS 75265
13
LM111, LM211, LM311
DIFFERENTIAL COMPARATORS WITH STROBES
SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003
APPLICATION INFORMATION
VCC+ = 5 V
3.9 kΩ
30 kن
1 kΩ
2N3708
1 kΩ
1N914
Output
+
2N2222
1N914
Input
From
TTL
2N2222
1.5 µF
2.7 kΩ
510 Ω
2N2222
2.2 kΩ
† Adjust to set clamp level
Figure 22. Precision Squarer
VCC+ = 5 V
5V
Opto Isolator
From
TTL
Gate
5 kΩ
1 kΩ
TTL
Output
100 Ω
1 kΩ
50 kΩ
0.01 µF
1 kΩ
Figure 23. Digital Transmission Isolator
VCC+ = 15 V
2 kΩ
Input
TL081
–
Output
10 kΩ
+
+
1 MΩ
VCC– = –15 V
1.5 µF
Figure 24. Positive-Peak Detector
14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
LM111, LM211, LM311
DIFFERENTIAL COMPARATORS WITH STROBES
SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003
APPLICATION INFORMATION
VCC+ = 15 V
1 MΩ
TL081
10 kΩ
2 kΩ
+
Input
Output
–
+
15 µF
VCC– = –15 V
Figure 25. Negative-Peak Detector
VCC+ = 5 V
3.9 kΩ
1N2175
2N3708
1 kΩ
Output
to TTL
2N2222
R1†
30 kΩ
† R1 sets the comparison level. At comparison, the photodiode has less than 5 mV across it, decreasing dark current by an order of magnitude.
Figure 26. Precision Photodiode Comparator
VCC+
Inputs
BAL/STRB
‡
VCC–
TTL
Strobe
2N3708
1 kΩ
‡ Transient voltage and inductive kickback protection
Figure 27. Relay Driver With Strobe
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
LM111, LM211, LM311
DIFFERENTIAL COMPARATORS WITH STROBES
SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003
APPLICATION INFORMATION
VCC+
620 Ω
BAL/STRB
300 Ω
1
100 kΩ
100 kΩ
Output
BAL/STRB
2
10 kΩ
Input
0.1 µF
300 Ω
47 Ω
620 Ω
VCC–
Figure 28. Switching Power Amplifier
VCC+
39 kΩ
620 Ω
300 kΩ
620 Ω
BAL/STRB
1
15 kΩ
Reference
VCC–
0.22 µF
620 Ω
V+
510 Ω
15 kΩ
510 Ω
Input
620 Ω
BAL/STRB
2
VCC–
39 kΩ
300 kΩ
620 Ω
620 Ω
Figure 29. Switching Power Amplifiers
16
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
Outputs
PACKAGE OPTION ADDENDUM
www.ti.com
25-Feb-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
JM38510/10304BPA
LM111FKB
Pins Package Eco Plan (2)
Qty
Package
Type
Package
Drawing
ACTIVE
CDIP
JG
8
1
None
ACTIVE
LCCC
FK
20
1
None
Lead/Ball Finish
A42 SNPB
MSL Peak Temp (3)
Level-NC-NC-NC
POST-PLATE Level-NC-NC-NC
LM111JG
ACTIVE
CDIP
JG
8
1
None
A42 SNPB
Level-NC-NC-NC
LM111JGB
ACTIVE
CDIP
JG
8
1
None
A42 SNPB
Level-NC-NC-NC
LM211D
ACTIVE
SOIC
D
8
75
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
LM211DR
ACTIVE
SOIC
D
8
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
LM211P
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
Level-NC-NC-NC
LM211PW
ACTIVE
TSSOP
PW
8
150
Pb-Free
(RoHS)
CU NIPDAU
Level-1-250C-UNLIM
LM211PWR
ACTIVE
TSSOP
PW
8
2000
Pb-Free
(RoHS)
CU NIPDAU
Level-1-250C-UNLIM
LM211QD
ACTIVE
SOIC
D
8
75
Pb-Free
(RoHS)
CU NIPDAU
Level-2-250C-1 YEAR/
Level-1-235C-UNLIM
LM211QDR
ACTIVE
SOIC
D
8
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-2-250C-1 YEAR/
Level-1-235C-UNLIM
LM311D
ACTIVE
SOIC
D
8
75
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
LM311DR
ACTIVE
SOIC
D
8
CU NIPDAU
Level-1-260C-UNLIM
LM311P
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
Level-NC-NC-NC
LM311PSR
ACTIVE
SO
PS
8
2000
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
LM311PW
ACTIVE
TSSOP
PW
8
150
Pb-Free
(RoHS)
CU NIPDAU
Level-1-250C-UNLIM
LM311PWLE
OBSOLETE
TSSOP
PW
8
None
Call TI
LM311PWR
ACTIVE
TSSOP
PW
8
Pb-Free
(RoHS)
CU NIPDAU
LM311Y
OBSOLETE
XCEPT
Y
0
None
Call TI
2500 Green (RoHS &
no Sb/Br)
2000
Call TI
Level-1-250C-UNLIM
Call TI
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional
product content details.
None: Not yet available Lead (Pb-Free).
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens,
including bromine (Br) or antimony (Sb) above 0.1% of total product weight.
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
25-Feb-2005
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
MECHANICAL DATA
MCER001A – JANUARY 1995 – REVISED JANUARY 1997
JG (R-GDIP-T8)
CERAMIC DUAL-IN-LINE
0.400 (10,16)
0.355 (9,00)
8
5
0.280 (7,11)
0.245 (6,22)
1
0.063 (1,60)
0.015 (0,38)
4
0.065 (1,65)
0.045 (1,14)
0.310 (7,87)
0.290 (7,37)
0.020 (0,51) MIN
0.200 (5,08) MAX
Seating Plane
0.130 (3,30) MIN
0.023 (0,58)
0.015 (0,38)
0°–15°
0.100 (2,54)
0.014 (0,36)
0.008 (0,20)
4040107/C 08/96
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
This package can be hermetically sealed with a ceramic lid using glass frit.
Index point is provided on cap for terminal identification.
Falls within MIL STD 1835 GDIP1-T8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MLCC006B – OCTOBER 1996
FK (S-CQCC-N**)
LEADLESS CERAMIC CHIP CARRIER
28 TERMINAL SHOWN
18
17
16
15
14
13
NO. OF
TERMINALS
**
12
19
11
20
10
A
B
MIN
MAX
MIN
MAX
20
0.342
(8,69)
0.358
(9,09)
0.307
(7,80)
0.358
(9,09)
28
0.442
(11,23)
0.458
(11,63)
0.406
(10,31)
0.458
(11,63)
21
9
22
8
44
0.640
(16,26)
0.660
(16,76)
0.495
(12,58)
0.560
(14,22)
23
7
52
0.739
(18,78)
0.761
(19,32)
0.495
(12,58)
0.560
(14,22)
24
6
68
0.938
(23,83)
0.962
(24,43)
0.850
(21,6)
0.858
(21,8)
84
1.141
(28,99)
1.165
(29,59)
1.047
(26,6)
1.063
(27,0)
B SQ
A SQ
25
5
26
27
28
1
2
3
4
0.080 (2,03)
0.064 (1,63)
0.020 (0,51)
0.010 (0,25)
0.020 (0,51)
0.010 (0,25)
0.055 (1,40)
0.045 (1,14)
0.045 (1,14)
0.035 (0,89)
0.045 (1,14)
0.035 (0,89)
0.028 (0,71)
0.022 (0,54)
0.050 (1,27)
4040140 / D 10/96
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
This package can be hermetically sealed with a metal lid.
The terminals are gold plated.
Falls within JEDEC MS-004
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MPDI001A – JANUARY 1995 – REVISED JUNE 1999
P (R-PDIP-T8)
PLASTIC DUAL-IN-LINE
0.400 (10,60)
0.355 (9,02)
8
5
0.260 (6,60)
0.240 (6,10)
1
4
0.070 (1,78) MAX
0.325 (8,26)
0.300 (7,62)
0.020 (0,51) MIN
0.015 (0,38)
Gage Plane
0.200 (5,08) MAX
Seating Plane
0.010 (0,25) NOM
0.125 (3,18) MIN
0.100 (2,54)
0.021 (0,53)
0.015 (0,38)
0.430 (10,92)
MAX
0.010 (0,25) M
4040082/D 05/98
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2005, Texas Instruments Incorporated