EDI BRUS710 Ultra-fast recovery approximately 25 amperes single-phase, full-wave bridge Datasheet

BRUS7
MINIBRIDGE
50 ns. ULTRA-FAST RECOVERY
Approximately 25 AMPERES*
SINGLE-PHASE, FULL-WAVE BRIDGES
SPACE SAVING
IN-LINE DESIGN
INTEGRALLY MOLDED
HEAT SINKS
PROVIDE LOW
THERMAL RESISTANCE
This product has recognition under the component program of Underwriters Laboratories, inc.
PRV/LEG
50V
TYPE NUMBER
BRUS705
100V
BRUS710
200V
400V
500V
600V
BRUS720
BRUS740
BRUS750
BRUS760
ELECTRICAL CHARACTERISTICS PER LEG
(at TA =25 C U nle ss O the rwis e Sp eci fie d)
BRUS7
UNITS
Average Output Current, lo @ 60 C TC
25
Amps
Max.Forward Voltage Drop, VF @ IF=12A pk
1.5
Volts
Max.DC Reverse Current @ PRV and 25 C , I R
10
A
Max.DC Reverse Current @ PRV and 100 C ,I R
200
A
Max.Reverse Recovery Time,Trr (Fig.3)
50
Nanosec.
Max.Peak Surge Current, lFSM (8.3ms)
320
Amps
O
Thermal Resistance (Total Bridge), R0- j -c
1.5 typ.
o
C/W
Storage Temperature Range, TSTG
-55 to+150
o
Ambient Operating Temperature Range,TA
-55 to+150
o
Note 1:Derate Io by 20% for capacitive loads
NOTE: Maximum lead and terminal temperature for soldering, 3/8 inch from case,5 seconds at 250 OC.
EDI reserves the right to change these specifications at any time without notice.
C
C
BRUS7
FIG.2
NON-REPETITIVE SURGE CURRENT
FIG.1
CURRENT DERATING
1000
lO.AVERAGE
L
FORWARD CURRENT(AMP)
60
REDUCE RATING B Y 20% FOR C APACATIVE LOADS
500
MAX.PEAK SURGE CURRENT IFSM
50
BRIDGE OUTPUT
RES.-IND. LOADS
40
30
20
10
200
100
50
20
0
10
0
25
75
50
100
125
1
150
5
2
10
20
50
100
NUMBER OF CYCLES AT 60 CPS
O
TC =TEMPERATURE ( C)
FIG. 3
REVERSE RECOVERY TEST METHOD
T RR
R1
50 OHM
ZERO
REFERENCE
0.5A
D.U.T.
+
-
1.0A
0.25A
PULSE
GENERATOR
R2
1 OHM
SCOPE
R1, R2 NON-INDUCTIVE RESISTORS
PULSE GENERATOR - HEWLETT
PACKARD 214A OR EQUIV.
IKC REP.RATE, 10 SEC. PULSE WIDTH
ADJUST PULSE AMPLITUDE FOR PEAK IR
BRUS7 MECHANICAL OUTLINE
1.125 SQ
Dielectric test voltage 2500 volts rms, max. 50-60Hz.
.405
MAX
.193 DIA
THRU HOLE
METAL
HEAT SINK
AC
.625 MIN
_
+
.750 MIN
.050
DIA.TYP.
1/8 NOM.
.20TYP
ON CENTERS
ALL DIMENSIONS IN INCHES
NOTE:
1. Corrosion resistant terminals designed for .250 female quick connector, wrap around or solder.
2. A thin film of silicone thermal compound is recommended between the Minibridge R
case and mounting surface for improved thermal conduction.
3. Higher dielectric strengths available. Consult factory.
ELECTRONIC DEVICES, INC. DESIGNERS AND MANUFACTURERS OF SOLID STATE DEVICES SINCE 1951.
21 GRAY OAKS AVENUE
* YONKERS. NEW YORK 10710 914-965-4400
Ee-mail:[email protected] *Wwebsite: http://www.edidiodes.com
* FAX 914-965-5531
* 1-800-678-0828
Similar pages