Click on Series name for product info on aimtec.com Series AM1PS-NZ 1 Watt | DC-DC Converter FEATURES: Unregulated 8 Pin DIP Package Low ripple and noise High efficiency up to 82% Operating temperature -40oC to + 105oC Input / Output isolation 1500 VDC Pin compatible with multiple manufacturers Continuous Short Circuit Protection ‡ Models Single output Model Input Voltage (V) Output Voltage (V) Output Current max (mA) Isolation (VDC) 2.97-3.63 2.97-3.63 4.5-5.5 4.5-5.5 4.5-5.5 4.5-5.5 4.5-5.5 4.5-5.5 10.8-13.2 10.8-13.2 10.8-13.2 10.8-13.2 10.8-13.2 21.6-26.4 21.6-26.4 21.6-26.4 21.6-26.4 21.6-26.4 21.6-26.4 3.3 5 3.3 5 9 12 15 24 3.3 5 9 12 15 3.3 5 9 12 15 24 303 200 303 200 111 84 67 42 303 200 110 83 67 303 200 110 83 67 42 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 AM1PS-0303S-NZ AM1PS-0305S-NZ AM1PS-0503S-NZ AM1PS-0505S-NZ AM1PS-0509S-NZ AM1PS-0512S-NZ AM1PS-0515S-NZ AM1PS-0524S-NZ ‡ AM1PS-1203S-NZ AM1PS-1205S-NZ AM1PS-1209S-NZ AM1PS-1212S-NZ AM1PS-1215S-NZ AM1PS-2403S-NZ AM1PS-2405S-NZ AM1PS-2409S-NZ AM1PS-2412S-NZ AM1PS-2415S-NZ AM1PS-2424S-NZ Max. Capacitive Load (µF) 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 Efficiency (%) 75 80 76 80 80 81 81 81 76 80 80 81 80 76 80 80 81 82 82 ‡- Please note Aimtec product change announcement located here www.aimtec.com/news for product specification changes effective February 7th 2015. Input Specifications Parameters Voltage range Absolute Max Rating (1 sec. max.) Nominal Typical 3.3 5 12 15 24 3.3 5 12 15 24 2.97-3.63 4.5-5.5 10.8-13.2 13.5-16.5 21.6-26.4 Maximum VDC 5 9 18 21 30 Filter Units VDC Capacitor Isolation Specifications Parameters Tested I/O voltage Resistance Capacitance www.aimtec.com F 051e R11.B Conditions Typical 60 sec > 1000 20 Tel: +1 514 620 2722 1 of 3 Rated Units 1500 VDC MOhm pF Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM1PS-NZ 1 Watt | DC-DC Converter Output Specifications Parameters Voltage accuracy Short Circuit protection Conditions Typical See tolerance graph ±5 Maximum Units % Continuous with automatic recovery ‡ For 1.0% Vin, 3.3V Model For 1.0% Vin, Other Model Load 10 – 100% Line voltage regulation Load voltage regulation Temperature coefficient Ripple & Noise ±1.5 ±1.2 12 ±0.03 60 At 20 MHz Bandwidth % of Vin % %/oC m Vp-p General Specifications Parameters Conditions Typical Maximum Units Switching frequency 100% load 100 - 300 KHz oC Operating temperature Derating above 85oC -40 to +105 oC Storage temperature -55 to +125 oC Maximum case temperature 125 Cooling Free air convection Humidity Non condensing 95 % Case material Plastic UL94-VO oC Lead Soldering Temperature 1.5mm from Lead, 10 sec max. 300 Weight 1.8 g Dimensions (L x W x H) 0.50 x 0.39 x 0.32 inches 12.70 x 10.00 x 8.20 mm MTBF >3500K hrs(MIL-HDBK -217F, Ground Benign, t=+25oC) NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Safety Specifications Parameters Agency approvals Standards cULus (without 3.3 input and output models) UL 60950-1 Pin Out Specifications Pin 1 4 5 6 7 8 Dimensions Single - V Input +V Input +V Output No pin -V Output No pin www.aimtec.com F 051e R11.B Tel: +1 514 620 2722 2 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM1PS-NZ 1 Watt | DC-DC Converter Derating Typical Characteristics Recommended Circuit for EMI Class B NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3.Mechanical drawings and specifications are for reference only. 4.All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5.Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R11.B Tel: +1 514 620 2722 3 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only