Maxim MAX1306 8-/4-/2-channel, 12-bit, simultaneous-sampling adcs with â±10v, â±5v, and 0 to 5v analog input range Datasheet

19-3052; Rev 4; 8/09
KIT
ATION
EVALU
E
L
B
A
IL
AVA
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
The MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–
MAX1314 12-bit, analog-to-digital converters (ADCs) offer
eight, four, or two independent input channels.
Independent track-and-hold (T/H) circuitry provides simultaneous sampling for each channel. The MAX1304/
MAX1305/MAX1306 provide a 0 to +5V input range with
±6V fault-tolerant inputs. The MAX1308/MAX1309/
MAX1310 provide a ±5V input range with ±16.5V fault-tolerant inputs. The MAX1312/MAX1313/MAX1314 have a
±10V input range with ±16.5V fault-tolerant inputs. These
ADCs convert two channels in 0.9µs, and up to eight
channels in 1.98µs, with an 8-channel throughput of
456ksps per channel. Other features include a 20MHz T/H
input bandwidth, internal clock, internal (+2.5V) or external
(+2.0V to +3.0V) reference, and power-saving modes.
A 20MHz, 12-bit, bidirectional parallel data bus provides the conversion results and accepts digital inputs
that activate each channel individually.
All devices operate from a +4.75V to +5.25V analog supply
and a +2.7V to +5.25V digital supply and consume 57mA
total supply current when fully operational.
Each device is available in a 48-pin 7mm x 7mm TQFP
package and operates over the extended -40°C to
+85°C temperature range.
Applications
SIN/COS Position Encoder
Multiphase Motor Control
Multiphase Power Monitoring
Features
o Up to Eight Channels of Simultaneous Sampling
8ns Aperture Delay
100ps Channel-to-Channel T/H Match
o Extended Input Ranges
0 to +5V (MAX1304/MAX1305/MAX1306)
-5V to +5V (MAX1308/MAX1309/MAX1310)
-10V to +10V (MAX1312/MAX1313/MAX1314)
o Fast Conversion Time
One Channel in 0.72µs
Two Channels in 0.9µs
Four Channels in 1.26µs
Eight Channels in 1.98µs
o High Throughput
1075ksps/Channel for One Channel
901ksps/Channel for Two Channels
680ksps/Channel for Four Channels
456ksps/Channel for Eight Channels
o ±1 LSB INL, ±0.9 LSB DNL (max)
o 84dBc SFDR, -86dBc THD, 71dB SINAD,
fIN = 500kHz at 0.4dBFS
o 12-Bit, 20MHz, Parallel Interface
o Internal or External Clock
o +2.5V Internal Reference or +2.0V to +3.0V
External Reference
o +5V Analog Supply, +3V to +5V Digital Supply
55mA Analog Supply Current
1.3mA Digital Supply Current
Shutdown and Power-Saving Modes
o 48-Pin TQFP Package (7mm x 7mm Footprint)
Ordering Information
Power-Grid Synchronization
Power-Factor Monitoring
PART
Vibration and Waveform Analysis
Selector Guide
TEMP RANGE
PIN-PACKAGE
MAX1304ECM+
-40°C to +85°C
48 TQFP
MAX1304ECM/V+
-40°C to +85°C
48 TQFP
MAX1305ECM+
-40°C to +85°C
48 TQFP
-40°C to +85°C
48 TQFP
INPUT RANGE (V)
CHANNEL COUNT
MAX1306ECM+
MAX1304ECM
0 to +5
8
MAX1308ECM+
-40°C to +85°C
48 TQFP
MAX1305ECM
0 to +5
4
MAX1308ECM/V+
-40°C to +85°C
48 TQFP
MAX1306ECM
0 to +5
2
MAX1309ECM+
-40°C to +85°C
48 TQFP
MAX1308ECM
±5
8
MAX1309ECM/V+
-40°C to +85°C
48 TQFP
MAX1309ECM
±5
4
MAX1310ECM+
-40°C to +85°C
48 TQFP
-40°C to +85°C
48 TQFP
-40°C to +85°C
48 TQFP
PART
MAX1310ECM
±5
2
MAX1312ECM+
MAX1312ECM
±10
8
MAX1313ECM+
MAX1313ECM
±10
4
MAX1314ECM
±10
2
MAX1314ECM+
-40°C to +85°C
48 TQFP
+Denotes a lead(Pb)-free/RoHS-compliant package.
/V denotes an automotive qualified part.
Pin Configurations appear at end of data sheet.
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
General Description
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
ABSOLUTE MAXIMUM RATINGS
AVDD to AGND .........................................................-0.3V to +6V
DVDD to DGND.........................................................-0.3V to +6V
AGND to DGND.....................................................-0.3V to +0.3V
CH0–CH7, I.C. to AGND (MAX1304/MAX1305/MAX1306)....±6V
CH0–CH7, I.C. to AGND (MAX1308/MAX1309/MAX1310)..±16.5V
CH0–CH7, I.C. to AGND (MAX1312/MAX1313/MAX1314)..±16.5V
D0–D11 to DGND ....................................-0.3V to (DVDD + 0.3V)
EOC, EOLC, RD, WR, CS to DGND .........-0.3V to (DVDD + 0.3V)
CONVST, CLK, SHDN, CHSHDN to DGND...-0.3V to (DVDD + 0.3V)
INTCLK/EXTCLK to AGND .......................-0.3V to (AVDD + 0.3V)
REFMS, REF, MSV to AGND.....................-0.3V to (AVDD + 0.3V)
REF+, COM, REF- to AGND.....................-0.3V to (AVDD + 0.3V)
Maximum Current into Any Pin Except AVDD, DVDD, AGND,
DGND ...........................................................................±50mA
Continuous Power Dissipation (TA = +70°C)
TQFP (derate 22.7mW/°C above +70°C) ................1818.2mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(AVDD = +5V, DVDD = +3V, AGND = DGND = 0, VREF = VREFMS = +2.5V (external reference), CREF = CREFMS = 0.1µF, CREF+ =
CREF- = 0.1µF, CREF+-to-REF- = 2.2µF || 0.1µF, CCOM = 2.2µF || 0.1µF, CMSV = 2.2µF || 0.1µF (unipolar devices), MSV = AGND (bipolar devices), fCLK = 16.67MHz 50% duty cycle, INTCLK/EXTCLK = AGND (external clock), SHDN = DGND, TA = TMIN to TMAX,
unless otherwise noted. Typical values are at TA = +25°C. See Figures 3 and 4.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
STATIC PERFORMANCE (Note 1)
Resolution
N
12
Bits
Integral Nonlinearity
INL
(Note 2)
±0.5
±1.0
LSB
Differential Nonlinearity
DNL
No missing codes (Note 2)
LSB
Offset Error
Offset-Error Matching
Offset-Error Temperature Drift
±0.3
±0.9
Unipolar, 0x000 to 0x001
±3
±16
Bipolar, 0xFFF to 0x000
±3
±16
Unipolar, between all channels
±9
±20
Bipolar, between all channels
±9
±20
Unipolar, 0x000 to 0x001
7
Bipolar, 0xFFF to 0x000
7
Gain Error
Gain-Error Matching
Between all channels
Gain-Error Temperature Drift
LSB
LSB
ppm/°C
±2
±16
±3
±14
4
LSB
LSB
ppm/°C
DYNAMIC PERFORMANCE at fIN = 500kHz, AIN = -0.4dBFS (Note 2)
Signal-to-Noise Ratio
Signal-to-Noise Plus Distortion
SNR
68
71
dB
SINAD
68
71
dB
Total Harmonic Distortion
THD
Spurious-Free Dynamic Range
SFDR
-86
Channel-to-Channel Isolation
80
-80
dBc
84
dBc
86
dB
ANALOG INPUTS (CH0 through CH7)
Input Voltage
2
VCH
MAX1304/MAX1305/MAX1306
0
+5
MAX1308/MAX1309/MAX1310
-5
+5
MAX1312/MAX1313/MAX1314
-10
+10
_______________________________________________________________________________________
V
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
(AVDD = +5V, DVDD = +3V, AGND = DGND = 0, VREF = VREFMS = +2.5V (external reference), CREF = CREFMS = 0.1µF, CREF+ =
CREF- = 0.1µF, CREF+-to-REF- = 2.2µF || 0.1µF, CCOM = 2.2µF || 0.1µF, CMSV = 2.2µF || 0.1µF (unipolar devices), MSV = AGND (bipolar devices), fCLK = 16.67MHz 50% duty cycle, INTCLK/EXTCLK = AGND (external clock), SHDN = DGND, TA = TMIN to TMAX,
unless otherwise noted. Typical values are at TA = +25°C. See Figures 3 and 4.)
PARAMETER
Input Resistance
(Note 3)
SYMBOL
RCH
CONDITIONS
MIN
7.58
MAX1308/MAX1309MAX1310
8.66
MAX1312/MAX1313/MAX1314
MAX1304/MAX1305/MAX1306
Input Current
(Note 3)
ICH
MAX1308/MAX1309/MAX1310
MAX1312/MAX1313/MAX1314
Input Capacitance
TYP
MAX1304/MAX1305/MAX1306
MAX
UNITS
kΩ
14.26
VCH = +5V
VCH = 0V
0.54
-0.157
-0.12
-1.16
-0.87
VCH = +5V
VCH = -5V
0.29
VCH = +10V
VCH = -10V
0.56
-1.13
CCH
0.72
0.39
mA
0.74
-0.85
15
pF
TRACK/HOLD
External-Clock Throughput Rate
(Note 4)
Internal-Clock Throughput Rate
(Note 4, Table 1)
fTH
fTH
One channel selected for conversion
1075
Two channels selected for conversion
901
Four channels selected for conversion
680
Eight channels selected for conversion
456
One channel selected for conversion
983
Two channels selected for conversion
821
Four channels selected for conversion
618
Eight channels selected for conversion
413
ksps
ksps
Small-Signal Bandwidth
20
MHz
Full-Power Bandwidth
20
MHz
8
ns
Aperture Delay
tAD
Aperture-Delay Matching
Aperture Jitter
tAJ
100
ps
50
psRMS
INTERNAL REFERENCE
REF Output Voltage
VREF
2.475
Reference Output-Voltage
Temperature Drift
2.500
2.525
30
VREFMS
REF+ Output Voltage
VREF+
3.850
V
COM Output Voltage
VCOM
2.600
V
VREF-
1.350
V
VREF+ VREF-
2.500
V
Differential Reference Voltage
2.500
ppm/°C
REFMS Output Voltage
REF- Output Voltage
2.475
V
2.525
V
_______________________________________________________________________________________
3
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
ELECTRICAL CHARACTERISTICS (continued)
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
ELECTRICAL CHARACTERISTICS (continued)
(AVDD = +5V, DVDD = +3V, AGND = DGND = 0, VREF = VREFMS = +2.5V (external reference), CREF = CREFMS = 0.1µF, CREF+ =
CREF- = 0.1µF, CREF+-to-REF- = 2.2µF || 0.1µF, CCOM = 2.2µF || 0.1µF, CMSV = 2.2µF || 0.1µF (unipolar devices), MSV = AGND (bipolar devices), fCLK = 16.67MHz 50% duty cycle, INTCLK/EXTCLK = AGND (external clock), SHDN = DGND, TA = TMIN to TMAX,
unless otherwise noted. Typical values are at TA = +25°C. See Figures 3 and 4.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
2.0
2.5
3.0
UNITS
EXTERNAL REFERENCE (REF and REFMS are externally driven)
REF Input Voltage Range
VREF
REF Input Resistance
RREF
(Note 5)
REF Input Capacitance
REFMS Input Voltage Range
VREFMS
REFMS Input Resistance
RREFMS
2.0
kΩ
15
pF
2.5
(Note 6)
REFMS Input Capacitance
V
5
3.0
V
5
kΩ
15
pF
REF+ Output Voltage
VREF+
VREF = +2.5V
3.850
V
COM Output Voltage
VCOM
VREF = +2.5V
2.600
V
REF- Output Voltage
VREF-
VREF = +2.5V
1.350
V
VREF+ VREF-
VREF = +2.5V
2.500
V
Differential Reference Voltage
DIGITAL INPUTS (D0–D7, RD, WR, CS, CLK, SHDN, CHSHDN, CONVST)
Input-Voltage High
VIH
Input-Voltage Low
VIL
0.7 x DVDD
V
0.3 x DVDD
Input Hysteresis
20
Input Capacitance
CIN
Input Current
IIN
15
VIN = 0 or DVDD
V
mV
pF
0.02
±1
µA
CLOCK-SELECT INPUT (INTCLK/EXTCLK)
Input-Voltage High
VIH
Input-Voltage Low
VIL
0.7 x AVDD
V
0.3 x AVDD
V
DIGITAL OUTPUTS (D0–D11, EOC, EOLC)
Output-Voltage High
VOH
ISOURCE = 0.8mA, Figure 1
Output-Voltage Low
VOL
ISINK = 1.6mA, Figure 1
DVDD - 0.6
V
D0–D11 Tri-State Leakage Current
RD = high or CS = high
0.06
D0–D11 Tri-State Output
Capacitance
RD = high or CS = high
15
0.4
V
1
µA
pF
POWER SUPPLIES
Analog Supply Voltage
AVDD
4.75
5.25
V
Digital Supply Voltage
DVDD
2.70
5.25
V
Analog Supply Current
4
IAVDD
MAX1304/MAX1305/MAX1306,
all channels selected
55
60
MAX1308/MAX1309/MAX1310,
all channels selected
54
60
MAX1312/MAX1313/MAX1314,
all channels selected
54
60
_______________________________________________________________________________________
mA
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
(AVDD = +5V, DVDD = +3V, AGND = DGND = 0, VREF = VREFMS = +2.5V (external reference), CREF = CREFMS = 0.1µF, CREF+ =
CREF- = 0.1µF, CREF+-to-REF- = 2.2µF || 0.1µF, CCOM = 2.2µF || 0.1µF, CMSV = 2.2µF || 0.1µF (unipolar devices), MSV = AGND (bipolar devices), fCLK = 16.67MHz 50% duty cycle, INTCLK/EXTCLK = AGND (external clock), SHDN = DGND, TA = TMIN to TMAX,
unless otherwise noted. Typical values are at TA = +25°C. See Figures 3 and 4.)
PARAMETER
SYMBOL
Digital Supply Current
(CLOAD = 100pF) (Note 7)
IDVDD
CONDITIONS
MIN
TYP
MAX
MAX1304/MAX1305/MAX1306,
all channels selected
1.3
2.6
MAX1308/MAX1309/MAX1310,
all channels selected
1.3
2.6
MAX1312/MAX1313/MAX1314,
all channels selected
1.3
2.6
Shutdown Current
(Note 8)
IAVDD
SHDN = DVDD, VCH = float
0.6
10
IDVDD
SHDN = DVDD, RD = WR = high
0.02
1
Power-Supply Rejection Ratio
PSRR
AVDD = +4.75V to +5.25V
50
Internal clock, Figure 7
800
External clock, Figure 8
12
Internal clock, Figure 7
200
External clock, Figure 8
3
UNITS
mA
µA
dB
TIMING CHARACTERISTICS (Figure 1)
Time to First Conversion Result
tCONV
Time to Subsequent Conversions
tNEXT
CONVST Pulse-Width Low
(Acquisition Time)
tACQ
(Note 9) Figures 6–10
0.1
900
ns
CLK
Cycles
225
ns
CLK
Cycles
1000.0
µs
CS Pulse Width
tCS
Figure 6
30
ns
RD Pulse-Width Low
tRDL
Figures 7, 8, 9
30
ns
RD Pulse-Width High
tRDH
Figures 7, 8, 9
30
ns
WR Pulse-Width Low
tWRL
Figure 6
30
CS to WR
tCTW
Figure 6
(Note 10)
ns
WR to CS
tWTC
Figure 6
(Note 10)
ns
CS to RD
tCTR
Figures 7, 8, 9
(Note 10)
ns
RD to CS
tRTC
Figures 7, 8, 9
(Note 10)
ns
Data Access Time
(RD Low to Valid Data)
tACC
Figures 7, 8, 9
tREQ
Figures 7, 8, 9
Bus Relinquish Time (RD High)
CLK Rise to EOC Delay
CLK Rise to EOLC Fall Delay
CONVST Fall to EOLC Rise Delay
tEOCD
Figure 8
tEOLCD
Figure 8
30
5
tEOC
External clock, Figure 8
30
20
tCVEOLCD Figures 7, 8, 9
Internal clock, Figure 7
EOC Pulse Width
ns
ns
ns
ns
20
ns
20
ns
1
CLK
Cycle
50
ns
_______________________________________________________________________________________
5
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
ELECTRICAL CHARACTERISTICS (continued)
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
ELECTRICAL CHARACTERISTICS (continued)
(AVDD = +5V, DVDD = +3V, AGND = DGND = 0, VREF = VREFMS = +2.5V (external reference), CREF = CREFMS = 0.1µF, CREF+ =
CREF- = 0.1µF, CREF+-to-REF- = 2.2µF || 0.1µF, CCOM = 2.2µF || 0.1µF, CMSV = 2.2µF || 0.1µF (unipolar devices), MSV = AGND (bipolar devices), fCLK = 16.67MHz 50% duty cycle, INTCLK/EXTCLK = AGND (external clock), SHDN = DGND, TA = TMIN to TMAX,
unless otherwise noted. Typical values are at TA = +25°C. See Figures 3 and 4.)
PARAMETER
SYMBOL
CONDITIONS
Input-Data Setup Time
tDTW
Figure 6
Input-Data Hold Time
tWTD
Figure 6
External CLK Period
tCLK
Figures 8, 9
MIN
TYP
MAX
10
UNITS
ns
10
ns
0.05
10.00
µs
External CLK High Period
tCLKH
Logic sensitive to rising edges,
Figures 8, 9
20
ns
External CLK Low Period
tCLKL
Logic sensitive to rising edges,
Figures 8, 9
20
ns
External Clock Frequency
fCLK
(Note 11)
0.1
Internal Clock Frequency
fINT
CONVST High to CLK Edge
tCNTC
20
15
Figures 8, 9
20
MHz
MHz
ns
Note 1: For the MAX1304/MAX1305/MAX1306, VIN = 0 to +5V. For the MAX1308/MAX1309/MAX1310, VIN = -5V to +5V. For the
MAX1312/MAX1313/MAX1314, VIN = -10V to +10V.
Note 2: All channel performance is guaranteed by correlation to a single channel test.
Note 3: The analog input resistance is terminated to an internal bias point (Figure 5). Calculate the analog input current using:
VCH _ − VBIAS
RCH _
ICH _ =
for VCH within the input voltage range.
Note 4: Throughput rate is given per channel. Throughput rate is a function of clock frequency (fCLK). The external clock throughput rate is specified with fCLK = 16.67MHz and the internal clock throughput rate is specified with fCLK = 15MHz. See the
Data Throughput section for more information.
Note 5: The REF input resistance is terminated to an internal +2.5V bias point (Figure 2). Calculate the REF input current using:
IREF =
VREF − 2.5V
RREF
for VREF within the input voltage range.
Note 6: The REFMS input resistance is terminated to an internal +2.5V bias point (Figure 2). Calculate the REFMS input current using:
IREFMS =
VREFMS − 2.5V
RREFMS
for VREFMS within the input voltage range.
Note 7: All analog inputs are driven with a -0.4dBFS 500kHz sine wave.
Note 8: Shutdown current is measured with the analog input floating. The large amplitude of the maximum shutdown current specification is due to automated test equipment limitations.
Note 9: CONVST must remain low for at least the acquisition period. The maximum acquisition time is limited by internal capacitor droop.
Note 10: CS to WR and CS to RD are internally AND together. Setup and hold times do not apply.
Note 11: Minimum CLK frequency is limited only by the internal T/H droop rate. Limit the time between the rising edge of CONVST
and the falling edge of EOLC to a maximum of 1ms.
6
_______________________________________________________________________________________
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
(AVDD = +5V, DVDD = +3V, AGND = DGND = 0, VREF = VREFMS = +2.5V (external reference), CREF = CREFMS = 0.1µF, CREF+ =
CREF- = 0.1µF, CREF+-to-REF- = 2.2µF || 0.1µF, CCOM = 2.2µF || 0.1µF, CMSV = 2.2µF || 0.1µF (unipolar devices), MSV = AGND (bipolar
devices), fCLK = 16.67MHz 50% duty cycle, INTCLK/EXTCLK = AGND (external clock), fIN = 500kHz, AIN = -0.4dBFS. TA = +25°C,
unless otherwise noted.) (Figures 3 and 4)
DIFFERENTIAL NONLINEARITY
vs. DIGITAL OUTPUT CODE
INTEGRAL NONLINEARITY
vs. DIGITAL OUTPUT CODE
0.6
0.8
0.6
0.4
0.2
0.2
DNL (LSB)
0.4
0
0
-0.2
-0.2
-0.4
-0.4
-0.6
-0.6
-0.8
-0.8
-1.0
-1.0
512 1024 1536 2048 2560 3072 3584 4096
DIGITAL OUTPUT CODE
DIGITAL OUTPUT CODE
OFFSET ERROR
vs. ANALOG SUPPLY VOLTAGE
OFFSET ERROR
vs. TEMPERATURE
16
MAX1304 toc03
1.0
0.8
0.6
12
8
0.4
OFFSET ERROR (LSB)
OFFSET ERROR (LSB)
0
512 1024 1536 2048 2560 3072 3584 4096
MAX1304 toc04
0
MAX1304 toc02
0.8
INL (LSB)
1.0
MAX1304 toc01
1.0
0.2
0
-0.2
-0.4
4
0
-4
-8
-0.6
-12
-0.8
-1.0
-16
4.7
4.8
4.9
5.0
5.1
5.2
5.3
-40
-15
10
35
60
85
TEMPERATURE (°C)
AVDD (V)
GAIN ERROR
vs. ANALOG SUPPLY VOLTAGE
0
MAX1304 toc06
16
MAX1304 toc05
1
GAIN ERROR
vs. TEMPERATURE
12
GAIN ERROR (LSB)
GAIN ERROR (LSB)
8
-1
-2
-3
4
0
-4
-8
-4
-12
-5
-16
4.7
4.8
4.9
5.0
AVDD (V)
5.1
5.2
5.3
-40
-15
10
35
60
85
TEMPERATURE (°C)
_______________________________________________________________________________________
7
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
Typical Operating Characteristics
Typical Operating Characteristics (continued)
(AVDD = +5V, DVDD = +3V, AGND = DGND = 0, VREF = VREFMS = +2.5V (external reference), CREF = CREFMS = 0.1µF, CREF+ =
CREF- = 0.1µF, CREF+-to-REF- = 2.2µF || 0.1µF, CCOM = 2.2µF || 0.1µF, CMSV = 2.2µF || 0.1µF (unipolar devices), MSV = AGND (bipolar
devices), fCLK = 16.67MHz 50% duty cycle, INTCLK/EXTCLK = AGND (external clock), fIN = 500kHz, AIN = -0.4dBFS. TA = +25°C,
unless otherwise noted.) (Figures 3 and 4)
SMALL-SIGNAL BANDWIDTH
vs. ANALOG INPUT FREQUENCY
0
2
MAX1304 toc07
AIN = -20dBFS
AIN = -0.5dBFS
0
-2
GAIN (dB)
-4
-6
-4
-6
-8
-8
-10
-10
-12
-12
0.1
1
100
10
0.1
1
ANALOG INPUT FREQUENCY (MHz)
FFT PLOT
(2048-POINT DATA RECORD)
OUTPUT HISTOGRAM (DC INPUT)
fTH = 1.04167Msps
fIN = 500kHz
AIN = -0.05dBFS
SNR = 70.7dB
SINAD = 70.6dB
THD = -87.5dBc
SFDR = 87.1dBc
-20
-30
-40
-50
5497
5000
4000
COUNTS
-10
6000
MAX1304 toc09
0
-60
-70
3000
2000
1611
-80
1084
1000
-90
-100
0
0
0
-110
0
100
200
300
FREQUENCY (kHz)
8
100
10
ANALOG INPUT FREQUENCY (MHz)
MAX1304 toc10
GAIN (dB)
-2
MAX1304 toc08
LARGE-SIGNAL BANDWIDTH
vs. ANALOG INPUT FREQUENCY
2
AMPLITUDE (dBFS)
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
400
500
2044
2045
2046
2047
2048
DIGITAL OUTPUT CODE
_______________________________________________________________________________________
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
(AVDD = +5V, DVDD = +3V, AGND = DGND = 0, VREF = VREFMS = +2.5V (external reference), CREF = CREFMS = 0.1µF, CREF+ =
CREF- = 0.1µF, CREF+-to-REF- = 2.2µF || 0.1µF, CCOM = 2.2µF || 0.1µF, CMSV = 2.2µF || 0.1µF (unipolar devices), MSV = AGND (bipolar
devices), fCLK = 16.67MHz 50% duty cycle, INTCLK/EXTCLK = AGND (external clock), fIN = 500kHz, AIN = -0.4dBFS. TA = +25°C,
unless otherwise noted.) (Figures 3 and 4)
SIGNAL-TO-NOISE PLUS DISTORTION
vs. CLOCK FREQUENCY
SIGNAL-TO-NOISE RATIO
vs. CLOCK FREQUENCY
78
76
78
76
74
SINAD (dB)
72
70
68
72
70
68
66
66
64
64
62
62
60
60
0
5
10
15
20
0
25
5
10
15
20
fCLK (MHz)
fCLK (MHz)
TOTAL HARMONIC DISTORTION
vs. CLOCK FREQUENCY
SPURIOUS-FREE DYNAMIC RANGE
vs. CLOCK FREQUENCY
100
MAX1304 toc13
-60
-65
95
90
-75
85
SFDR (dBc)
-70
-80
25
MAX1304 toc14
SNR (dB)
74
THD (dBc)
MAX1304 toc12
80
MAX1304 toc11
80
80
-85
75
-90
70
-95
65
60
-100
0
5
10
15
fCLK (MHz)
20
25
0
5
10
15
20
25
fCLK (MHz)
_______________________________________________________________________________________
9
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
Typical Operating Characteristics (continued)
Typical Operating Characteristics (continued)
(AVDD = +5V, DVDD = +3V, AGND = DGND = 0, VREF = VREFMS = +2.5V (external reference), CREF = CREFMS = 0.1µF, CREF+ =
CREF- = 0.1µF, CREF+-to-REF- = 2.2µF || 0.1µF, CCOM = 2.2µF || 0.1µF, CMSV = 2.2µF || 0.1µF (unipolar devices), MSV = AGND (bipolar
devices), fCLK = 16.67MHz 50% duty cycle, INTCLK/EXTCLK = AGND (external clock), fIN = 500kHz, AIN = -0.4dBFS. TA = +25°C,
unless otherwise noted.) (Figures 3 and 4)
SIGNAL-TO-NOISE PLUS DISTORTION
vs. REFERENCE VOLTAGE
SIGNAL-TO-NOISE RATIO
vs. REFERENCE VOLTAGE
74
73
74
73
72
SINAD (dB)
72
SNR (dB)
MAX1304 toc16
75
MAX1304 toc15
75
71
70
69
71
70
69
68
68
67
67
66
66
65
65
2.0
2.2
2.4
2.6
2.8
2.0
3.0
2.2
2.4
2.6
2.8
3.0
VREF (V)
VREF (V)
TOTAL HARMONIC DISTORTION
vs. REFERENCE VOLTAGE
SPURIOUS-FREE DYNAMIC RANGE
vs. REFERENCE VOLTAGE
-72
-74
MAX1304 toc18
100
MAX1304 toc17
-70
95
-76
90
-78
SFDR (dBc)
THD (dBc)
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
-80
-82
85
80
-84
-86
75
-88
-90
70
2.0
2.2
2.4
2.6
VREF (V)
10
2.8
3.0
2.0
2.2
2.4
2.6
2.8
VREF (V)
______________________________________________________________________________________
3.0
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
TA = +85°C
56
2.0
MAX1304 toc19
57
CLOAD = 50pF
1.8
TA = +85°C
1.6
IDVDD (mA)
IAVDD (mA)
55
TA = +25°C
54
TA = +25°C
1.4
TA = -40°C
1.2
TA = -40°C
53
1.0
52
0.8
0.6
51
4.7
4.8
4.9
5.0
5.1
2.5
5.3
5.2
3.0
3.5
4.0
4.5
5.5
5.0
DVDD (V)
AVDD (V)
DIGITAL SHUTDOWN CURRENT
vs. DIGITAL SUPPLY VOLTAGE
ANALOG SHUTDOWN CURRENT
vs. ANALOG SUPPLY VOLTAGE
680
660
MAX1304 toc22
22
MAX1304 toc21
700
20
640
18
620
IDVDD (nA)
IAVDD (nA)
MAX1304 toc20
DIGITAL SUPPLY CURRENT
vs. DIGITAL SUPPLY VOLTAGE
ANALOG SUPPLY CURRENT
vs. ANALOG SUPPLY VOLTAGE
600
580
16
14
560
540
12
520
10
500
4.7
4.8
4.9
5.0
5.1
2.5
5.3
5.2
3.0
3.5
4.5
5.5
5.0
DIGITAL SUPPLY CURRENT
vs. NUMBER OF CHANNELS SELECTED
ANALOG SUPPLY CURRENT
vs. NUMBER OF CHANNELS SELECTED
CHSHDN = 0
55
MAX1304 toc24
1.0
MAX1304 toc23
60
CHSHDN = 0
0.9
0.8
0.7
IDVDD (mA)
50
IAVDD (mA)
4.0
DVDD (V)
AVDD (V)
45
0.6
0.5
0.4
40
0.3
35
0.2
0.1
30
0
1
2
3
4
5
6
7
NUMBER OF CHANNELS SELECTED
8
0
1
2
3
4
5
6
7
8
NUMBER OF CHANNELS SELECTED
______________________________________________________________________________________
11
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
Typical Operating Characteristics (continued)
(AVDD = +5V, DVDD = +3V, AGND = DGND = 0, VREF = VREFMS = +2.5V (external reference), CREF = CREFMS = 0.1µF, CREF+ =
CREF- = 0.1µF, CREF+-to-REF- = 2.2µF || 0.1µF, CCOM = 2.2µF || 0.1µF, CMSV = 2.2µF || 0.1µF (unipolar devices), MSV = AGND (bipolar
devices), fCLK = 16.67MHz 50% duty cycle, INTCLK/EXTCLK = AGND (external clock), fIN = 500kHz, AIN = -0.4dBFS. TA = +25°C,
unless otherwise noted.) (Figures 3 and 4)
Typical Operating Characteristics (continued)
(AVDD = +5V, DVDD = +3V, AGND = DGND = 0, VREF = VREFMS = +2.5V (external reference), CREF = CREFMS = 0.1µF, CREF+ =
CREF- = 0.1µF, CREF+-to-REF- = 2.2µF || 0.1µF, CCOM = 2.2µF || 0.1µF, CMSV = 2.2µF || 0.1µF (unipolar devices), MSV = AGND (bipolar
devices), fCLK = 16.67MHz 50% duty cycle, INTCLK/EXTCLK = AGND (external clock), fIN = 500kHz, AIN = -0.4dBFS. TA = +25°C,
unless otherwise noted.) (Figures 3 and 4)
INTERNAL REFERENCE VOLTAGE
INTERNAL REFERENCE VOLTAGE
vs. ANALOG SUPPLY VOLTAGE
vs. TEMPERATURE
MAX1304 toc26
2.5003
2.503
2.5002
2.502
2.5001
2.501
VREF (V)
VREF (V)
2.504
MAX1304 toc25
2.5004
2.5000
2.500
2.4999
2.499
2.4998
2.498
2.4997
2.497
2.4996
2.496
4.7
4.8
4.9
5.0
5.1
5.3
5.2
-40
-15
AVDD (V)
85
60
820
MAX1304 toc28
800
800
tCONV
tCONV
600
780
TIME (ns)
TIME (ns)
35
INTERNAL CLOCK CONVERSION TIME
vs. TEMPERATURE
MAX1304 toc27
900
700
10
TEMPERATURE (°C)
INTERNAL CLOCK CONVERSION TIME
vs. ANALOG SUPPLY VOLTAGE
500
400
tNEXT
300
tNEXT
200
200
180
100
0
4.8
4.9
5.0
5.1
160
5.3
5.2
-40
-15
AVDD (V)
ANALOG INPUT CHANNEL CURRENT
vs. ANALOG INPUT CHANNEL VOLTAGE
ANALOG INPUT CHANNEL CURRENT
vs. ANALOG INPUT CHANNEL VOLTAGE
MAX1304/MAX1305/MAX1306
1.5
2.5
2.0
1.0
1.5
0.5
0
-0.5
-6
-4
-2
0
VCH_ (V)
2
4
6
0
-1.0
-1.5
-2.5
-3.0
-2.0
0.5
-0.5
-2.0
-1.5
MAX1312/MAX1313/MAX1314
1.0
-1.0
-1.5
-1.0
85
60
2.0
ICH_ (mA)
ICH_ (mA)
0
-0.5
12
MAX1308/MAX1309/MAX1310
1.5
1.0
0.5
35
ANALOG INPUT CHANNEL CURRENT
vs. ANALOG INPUT CHANNEL VOLTAGE
MAX1304 toc30
3.0
MAX1304 toc29
2.0
10
TEMPERATURE (°C)
MAX1304 toc31
4.7
ICH_ (mA)
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
-2.0
-20
-15
-10
-5
0
VCH_ (V)
5
10
15
20
-20
-15
-10
-5
0
VCH_ (V)
______________________________________________________________________________________
5
10
15
20
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
PIN
MAX1304
MAX1308
MAX1312
MAX1305
MAX1309
MAX1313
MAX1306
MAX1310
MAX1314
NAME
FUNCTION
1, 15, 17
1, 15, 17
1, 15, 17
AVDD
Analog Power Input. AVDD is the power input for the analog section of the
converter. Apply +5V to AVDD. Connect all AVDD pins together. See the Layout,
Grounding, and Bypassing section for additional information.
2, 3, 14,
16, 23
2, 3, 14,
16, 23
2, 3, 14,
16, 23
AGND
Analog Ground. AGND is the power return for AVDD. Connect all AGND
pins together.
4
4
4
CH0
Channel 0 Analog Input
5
5
5
CH1
Channel 1 Analog Input
6
6
6
MSV
Midscale Voltage Bypass. For the unipolar MAX1304/MAX1305/MAX1306,
connect a 2.2µF and a 0.1µF capacitor from MSV to AGND. For the bipolar
MAX1308/MAX1309/MAX1310/MAX1312/MAX1313/MAX1314, connect
MSV to AGND.
7
7
—
CH2
Channel 2 Analog Input
8
8
—
CH3
Channel 3 Analog Input
9
—
—
CH4
Channel 4 Analog Input
10
—
—
CH5
Channel 5 Analog Input
11
—
—
CH6
Channel 6 Analog Input
12
—
—
CH7
Channel 7 Analog Input
13
13
13
Clock-Mode Select Input. Connect INTCLK/EXTCLK to AVDD to select the
INTCLK/
internal clock. Connect INTCLK/EXTCLK to AGND to use an external clock
EXTCLK
connected to CLK.
18
18
18
REFMS
19
19
19
REF
Midscale Reference Bypass or Input. REFMS connects through a 5kΩ resistor to
the internal +2.5V bandgap reference buffer.
For the MAX1304/MAX1305/MAX1306 unipolar devices, VREFMS is the input to
the unity-gain buffer that drives MSV. MSV sets the midpoint of the input voltage
range. For internal reference operation, bypass REFMS with a ≥0.01µF
capacitor to AGND. For external reference operation, drive REFMS with an
external voltage from +2V to +3V.
For the MAX1308/MAX1309/MAX1310/MAX1312/MAX1313/MAX1314 bipolar
devices, connect REFMS to REF. For internal reference operation, bypass the
REFMS/REF node with a ≥0.01µF capacitor to AGND. For external reference
operation, drive the REFMS/REF node with an external voltage from +2V to +3V.
ADC Reference Bypass or Input. REF connects through a 5kΩ resistor to the
internal +2.5V bandgap reference buffer.
For internal reference operation, bypass REF with a ≥0.01µF capacitor.
For external reference operation with the MAX1304/MAX1305/MAX1306
unipolar devices, drive REF with an external voltage from +2V to +3V.
For external reference operation with the MAX1308/MAX1309/MAX1310/
MAX1312/MAX1313/MAX1314 bipolar devices, connect REFMS to REF and
drive the REFMS/REF node with an external voltage from +2V to +3V.
______________________________________________________________________________________
13
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
Pin Description
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
Pin Description (continued)
PIN
MAX1304
MAX1308
MAX1312
MAX1305
MAX1309
MAX1313
MAX1306
MAX1310
MAX1314
NAME
FUNCTION
20
20
20
REF+
Positive Reference Bypass. Bypass REF+ with a 0.1µF capacitor to AGND. Also
bypass REF+ to REF- with a 2.2µF and a 0.1µF capacitor.
VREF+ = VCOM + VREF / 2.
21
21
21
COM
Reference Common Bypass. Bypass COM to AGND with a 2.2µF and a 0.1µF
capacitor. VCOM = 13 / 25 x AVDD.
22
22
22
REF-
Negative Reference Bypass. Bypass REF- with a 0.1µF capacitor to AGND.
Also bypass REF- to REF+ with a 2.2µF and a 0.1µF capacitor.
VREF+ = VCOM - VREF / 2.
24, 39
24, 39
24, 39
DGND
Digital Ground. DGND is the power return for DVDD. Connect all DGND
pins together.
25, 38
25, 38
25, 38
DVDD
Digital Power Input. DVDD powers the digital section of the converter, including
the parallel interface. Apply +2.7V to +5.25V to DVDD. Bypass DVDD to DGND
with a 0.1µF capacitor. Connect all DVDD pins together.
26
26
26
D0
Digital I/O 0 of 12-Bit Parallel Data Bus. High impedance when RD = 1 or CS = 1.
27
27
27
D1
Digital I/O 1 of 12-Bit Parallel Data Bus. High impedance when RD = 1 or CS = 1.
28
28
28
D2
Digital I/O 2 of 12-Bit Parallel Data Bus. High impedance when RD = 1 or CS = 1.
29
29
29
D3
Digital I/O 3 of 12-Bit Parallel Data Bus. High impedance when RD = 1 or CS = 1.
30
30
30
D4
Digital I/O 4 of 12-Bit Parallel Data Bus. High impedance when RD = 1 or CS = 1.
31
31
31
D5
Digital I/O 5 of 12-Bit Parallel Data Bus. High impedance when RD = 1 or CS = 1.
32
32
32
D6
Digital I/O 6 of 12-Bit Parallel Data Bus. High impedance when RD = 1 or CS = 1.
33
33
33
D7
Digital I/O 7 of 12-Bit Parallel Data Bus. High impedance when RD = 1 or CS = 1.
34
34
34
D8
Digital Output 8 of 12-Bit Parallel Data Bus. High impedance when RD = 1 or
CS = 1.
35
35
35
D9
Digital Output 9 of 12-Bit Parallel Data Bus. High impedance when RD = 1 or
CS = 1.
36
36
36
D10
Digital Output 10 of 12-Bit Parallel Data Bus. High impedance when RD = 1 or
CS = 1.
37
37
37
D11
Digital Output 11 of 12-Bit Parallel Data Bus. High impedance when RD = 1 or
CS = 1.
40
40
40
EOC
End-of-Conversion Output. EOC goes low to indicate the end of a conversion. It
returns high on the next rising CLK edge or the falling CONVST edge.
41
41
41
EOLC
End-of-Last-Conversion Output. EOLC goes low to indicate the end of the
last conversion. It returns high when CONVST goes low for the next
conversion sequence.
42
42
42
RD
Read Input. Pulling RD low initiates a read command of the parallel data bus.
WR
Write Input. Pulling WR low initiates a write command for configuring the device
with D0–D7.
43
14
43
43
______________________________________________________________________________________
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
PIN
MAX1304
MAX1308
MAX1312
MAX1305
MAX1309
MAX1313
MAX1306
MAX1310
MAX1314
NAME
FUNCTION
44
44
44
CS
Chip-Select Input. Pulling CS low activates the digital interface. Forcing CS high
places D0–D11 in high-impedance mode.
45
45
45
CONVST
46
46
46
CLK
47
47
47
SHDN
Conversion Start Input. Driving CONVST high initiates the conversion process.
The analog inputs are sampled on the rising edge of CONVST.
External Clock Input. For external clock operation, connect INTCLK/EXTCLK to
DGND and drive CLK with an external clock signal from 100kHz to 20MHz. For
internal clock operation, connect INTCLK/EXTCLK to DVDD and connect CLK to
DGND.
Shutdown Input. Driving SHDN high initiates device shutdown. Connect SHDN
to DGND for normal operation.
Active-Low Analog-Input Channel-Shutdown Input. Drive CHSHDN low to
power down analog inputs that are not selected for conversion in the
configuration register. Drive CHSHDN high to power up all analog input
CHSHDN
channels regardless of whether they are selected for conversion in the
configuration register. See the Channel Shutdown (CHSHDN) section for more
information.
48
48
48
—
9, 10,
11, 12
7, 8, 9,
10, 11, 12
I.C.
Internally connected. Connect I.C. to AGND.
Detailed Description
VDD
IOL = 1.6mA
1.6V
DEVICE PIN
100pF
IOH = 0.8mA
The MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–
MAX1314 are 12-bit ADCs. The devices offer 8, 4, or 2
independently selectable input channels, each with
dedicated T/H circuitry. Simultaneous sampling of all
active channels preserves relative phase information
making these devices ideal for motor control and power
monitoring. Three input ranges are available, 0 to +5V,
±5V and ±10V. The 0 to +5V devices provide ±6V faulttolerant inputs. The ±5V and ±10V devices provide
±16.5V fault-tolerant inputs. Two-channel conversion
results are available in 0.9µs. Conversion results from
all eight channels are available in 1.98µs. The 8-channel throughput is 456ksps per channel. Internal or
external reference and clock capability offer great flexibility, and ease of use. A write-only configuration register can mask out unused channels and a shutdown
feature reduces power. A 20MHz, 12-bit, parallel data
bus outputs the conversion results. Figure 2 shows the
functional diagram of these ADCs.
Figure 1. Digital Load Test Circuit
______________________________________________________________________________________
15
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
Pin Description (continued)
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
MAX1304–MAX1306
MAX1308–MAX1310
MAX1312–MAX1314
AVDD
CH0
DVDD
D11
T/H
12-BIT
ADC
8x1
MUX
CH7
D8
8 x 12
SRAM
OUTPUT
DRIVERS
T/H
D7
D0
MSV
CONFIGURATION
REGISTER
*
WR
CS
REF+
COM
REF-
INTERFACE
AND
CONTROL
RD
CONVST
SHDN
5kΩ
INTCLK/EXTCLK
REF
CLK
5kΩ
CHSHDN
REFMS
EOC
2.500V
EOLC
DGND
AGND
*SWITCH CLOSED ON UNIPOLAR DEVICES, OPEN ON BIPOLAR DEVICES
Figure 2. Functional Diagram
16
______________________________________________________________________________________
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
DVDD
0.1µF
1
0.1µF
15
0.1µF
17
BIPOLAR
CONFIGURATION
18
0.01µF
19
AVDD
DGND
AVDD
CLK
REFMS
MAX1308
MAX1312
CONVST
CS
WR
0.1µF
20
REF+
0.1µF
2.2µF
RD
EOLC
22
REF0.1µF
SHDN
MSV
REF
EOC
24, 39
GND
48
47
46
45
44
43
DIGITAL
INTERFACE
AND
CONTROL
42
41
40
2.2µF
D11
21
0.1µF
GND
+2.7V TO +5.25V
0.1µF
AVDD
CHSHDN
6
25, 38
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
+5V
COM
D9
2, 3, 14, 16, 23
12
11
10
BIPOLAR
ANALOG
INPUTS
9
D10
37
36
35
34
AGND
D8
CH7
D7
CH6
D6
CH5
D5
CH4
D4 30
8 CH3
7 CH2
5 CH1
4 CH0
13 INTCLK/EXTCLK
D3
D2
33
32
31
PARALLEL
DIGITAL
OUTPUT
29
28
D1 27
D0 26
Figure 3. Typical Bipolar Operating Circuit
______________________________________________________________________________________
17
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
+5V
0.1µF
1
0.1µF
15
0.1µF
17
DVDD
AVDD
25, 38
+2.7V TO +5.25V
0.1µF
AVDD
DGND
AVDD
24, 39
GND
2.2µF
6
0.1µF
MSV
SHDN
CLK
0.01µF
UNIPOLAR
CONFIGURATION
CHSHDN
18
0.01µF
19
REFMS
CONVST
MAX1304
REF
CS
WR
0.1µF
20
RD
REF+
0.1µF
2.2µF
EOLC
EOC
22
48
47
46
45
44
43
DIGITAL
INTERFACE
AND
CONTROL
42
41
40
REF0.1µF 2.2µF
D11
21
0.1µF
COM
D10
D9
GND
2, 3, 14, 16, 23
12
11
10
UNIPOLAR
ANALOG
INPUTS
AGND
D8
CH7
D7
CH6
D6
CH5
D5
9
CH4
8 CH3
7 CH2
5 CH1
4 CH0
13 INTCLK/EXTCLK
37
36
35
34
33
32
31
PARALLEL
DIGITAL
OUTPUT
D4 30
D3
D2
29
28
D1 27
D0 26
Figure 4. Typical Unipolar Operating Circuit
18
______________________________________________________________________________________
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
AVDD
*RSOURCE
CH_
OVERVOLTAGE
PROTECTION
CLAMP
2.5pF
R1
CHOLD
Selecting an Input Buffer
ANALOG
SIGNAL
SOURCE
UNDERVOLTAGE
PROTECTION
CLAMP
CSAMPLE
R2
VBIAS
*MINIMIZE RSOURCE TO AVOID GAIN ERROR AND DISTORTION.
PART
MAX1304
MAX1305
MAX1306
MAX1308
MAX1309
MAX1310
MAX1312
MAX1313
MAX1314
INPUT RANGE (V) R1 (kΩ) R2 (kΩ) VBIAS (V)
0 TO +5
3.33
5.00
0.90
±5
6.67
2.86
2.50
±10
13.33
2.35
2.06
R1 | | R2 = 2kΩ
Figure 5. Single-Channel, Equivalent Analog Input T/H Circuit
Analog Inputs
Track and Hold (T/H)
To preserve phase information across the multichannel
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–
MAX1314, all input channels have dedicated T/H amplifiers. Figure 5 shows the equivalent analog input T/H
circuit for one channel.
The input T/H circuit is controlled by the CONVST input.
When CONVST is low, the T/H circuit tracks the analog
input. When CONVST is high the T/H circuit holds the
analog input. The rising edge of CONVST is the analog
input sampling instant. There is an aperture delay (tAD)
of 8ns and a 50psRMS aperture jitter (tAJ). The aperture
delay of each dedicated T/H input is matched within
100ps of each other.
To settle the charge on CSAMPLE to 12-bit accuracy,
use a minimum acquisition time (t ACQ ) of 100ns.
Therefore, CONVST must be low for at least 100ns.
Although longer acquisition times allow the analog input
to settle to its final value more accurately, the maximum
To improve the input signal bandwidth under AC conditions, drive the input with a wideband buffer (>50MHz)
that can drive the ADC’s input capacitance (15pF) and
settle quickly. For example, the MAX4431 or the
MAX4265 can be used for the 0 to +5V unipolar devices,
or the MAX4350 can be used for ±5V bipolar inputs.
Most applications require an input buffer to achieve 12-bit
accuracy. Although slew rate and bandwidth are important, the most critical input buffer specification is settling
time. The simultaneous sampling of multiple channels
requires an acquisition time of 100ns. At the beginning of
the acquisition, the ADC internal sampling capacitor array
connects to the analog inputs, causing some disturbance. Ensure the amplifier is capable of settling to at
least 12-bit accuracy during this interval. Use a low-noise,
low-distortion, wideband amplifier that settles quickly and
is stable with the ADC’s 15pF input capacitance.
See the Maxim website at www.maxim-ic.com for application notes on how to choose the optimum buffer
amplifier for your ADC application.
Input Bandwidth
The input-tracking circuitry has a 20MHz small-signal
bandwidth, making it possible to digitize high-speed
transient events and measure periodic signals with
bandwidths exceeding the ADC’s sampling rate by
using undersampling techniques. To avoid high-frequency signals being aliased into the frequency band
of interest, anti-alias filtering is recommended.
Input Range and Protection
The MAX1304/MAX1305/MAX1306 provide a 0 to +5V
input voltage range with fault protection of ±6V. The
MAX1308/MAX1309/MAX1310 provide a ±5V input voltage range with fault protection of ±16.5V. The
MAX1312/MAX1313/MAX1314 provide a ±10V input
voltage range with fault protection of ±16.5V. Figure 5
shows the single-channel equivalent input circuit.
______________________________________________________________________________________
19
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
MAX1304–MAX1306
MAX1308–MAX1310
MAX1312–MAX1314
acquisition time must be limited to 1ms. Accuracy with
conversion times longer than 1ms cannot be guaranteed due to capacitor droop in the input circuitry.
Due to the analog input resistive divider formed by R1
and R2 in Figure 5, any significant analog input source
resistance (R SOURCE) results in gain error. Furthermore, R SOURCE causes distortion due to nonlinear
analog input currents. Limit RSOURCE to a maximum
of 100Ω.
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
Data Throughput
Clock Modes
The data throughput (fTH) of the MAX1304–MAX1306/
MAX1308–MAX1310/MAX1312–MAX1314 is a function
of the clock speed (fCLK). In internal clock mode, fCLK =
15MHz (typ). In external clock mode, 100kHz ≤ fCLK ≤
20MHz. When reading during conversion (Figures 7 and
8), calculate fTH as follows:
The MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–
MAX1314 provide a 15MHz internal conversion clock.
Alternatively, an external clock can be used.
fTH =
tACQ + tQUIET
1
12 + 3 x (N − 1) + 1
+
fCLK
where N is the number of active channels and tQUIET is
the period of bus inactivity before the rising edge of
CONVST. See the Starting a Conversion section for
more information.
Table 1 uses the above equation and shows the total
throughput as a function of the number of channels
selected for conversion.
Internal Clock
Internal clock mode frees the microprocessor from the
burden of running the ADC conversion clock. For internal clock operation, connect INTCLK/EXTCLK to AVDD
and connect CLK to DGND. Note that INTCLK/EXTCLK
is referenced to AVDD, not DVDD.
External Clock
For external clock operation, connect INTCLK/EXTCLK
to AGND and connect an external clock source to CLK.
Note that INTCLK/EXTCLK is referenced to AVDD, not
DV DD . The external clock frequency can be up to
20MHz. Linearity is not guaranteed with clock frequencies below 100kHz due to droop in the T/H circuits.
Table 1. Throughput vs. Channels Sampled: fCLK = 15MHz, tACQ = 100ns, tQUIET = 50ns
20
CHANNELS
SAMPLED
(N)
CLOCK CYCLES
UNTIL
LAST RESULT
CLOCK CYCLE
FOR READING
LAST CONVERSION
1
12
1
2
15
1
3
18
1
4
21
1
5
24
6
7
8
TOTAL
CONVERSION
TIME (ns)
TOTAL
THROUGHPUT
(ksps)
THROUGHPUT
PER CHANNEL
(fTH)
800
983
983
1000
1643
821
1200
2117
705
1400
2474
618
1
1600
2752
550
27
1
1800
2975
495
30
1
2000
3157
451
33
1
2200
3310
413
______________________________________________________________________________________
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
Digital Interface
The bidirectional parallel digital interface allows for setting
the 8-bit configuration register (see the Configuration
Register section) and reading the 12-bit conversion
result. The interface includes the following control signals:
chip select (CS), read (RD), write (WR), end of conversion
(EOC), end of last conversion (EOLC), conversion start
(CONVST), shutdown (SHDN), channel shutdown
(CHSHDN), internal clock select (INTCLK/EXTCLK), and
external clock input (CLK). Figures 6, 7, 8, 9, Table 2, and
the Timing Characteristics show the operation of the interface. D0–D7 are bidirectional, and D8–D11 are output
only. D0–D11 go high impedance when RD = 1 or CS = 1.
However, the new configuration does not take effect
until the next CONVST falling edge. At power-up all
channels default active. Shutdown does not change the
configuration register. The configuration register may
be written to in shutdown. See the Channel Shutdown
(CHSHDN) section for information about using the configuration register for power saving.
CONVST
CONFIGURATION
REGISTER UPDATES
RD
tCS
Configuration Register
Enable channels as active by writing to the configuration register through I/O lines D0–D7 (Table 2). The bits
in the configuration register map directly to the channels, with D0 controlling channel zero, and D7 controlling channel seven. Setting any bit high activates the
corresponding input channel, while resetting any bit
low deactivates the corresponding channel. On the
devices with less than eight channels, some of the bits
have no function (Table 2).
To write to the configuration register, pull CS and WR
low, load bits D0 through D7 onto the parallel bus, and
force WR high. The data are latched on the rising edge
of WR (Figure 6). Write to the configuration register at
any point during the conversion sequence. At powerup, write to the configuration register to select the
active channels before beginning a conversion.
CS
tWRL
tCTW
tWTC
WR
tDTW
D0–D7
DATA-IN
tWTD
Figure 6. Write Timing
Table 2. Configuration Register
PART
NUMBER
MAX1304
MAX1308
MAX1312
MAX1305
MAX1309
MAX1313
MAX1306
MAX1310
MAX1314
STATE
BIT/CHANNEL
D0/CH0
D1/CH1
D2/CH2
D3/CH3
D4/CH4
D5/CH5
D6/CH6
D7/CH7
ON
1
1
1
1
1
1
1
1
OFF
0
0
0
0
0
0
0
0
ON
1
1
1
1
X
X
X
X
OFF
0
0
0
0
X
X
X
X
ON
1
1
X
X
X
X
X
X
OFF
0
0
X
X
X
X
X
X
X = Don’t care (must be 1 or 0).
______________________________________________________________________________________
21
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
Applications Information
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
SAMPLE
INSTANT
tACQ
CONVST
HOLD
TRACK
tCONV
TRACK
tNEXT
EOC
tEOC
tCVEOLCD
EOLC
tQUIET ≥ 50ns
CS*
tCTR
tRDH
tRTC
RD
tACC
tRDL
CH0
D0–D11
CH1
tREQ
*CS CAN BE LOW AT ALL TIMES, LOW DURING THE RD CYCLES, OR THE SAME AS RD.
Figure 7. Read During Conversion—Channel 0 and Channel 1 Selected, Internal Clock
Starting a Conversion
To start a conversion using internal clock mode, pull
CONVST low for the acquisition time (tACQ). The T/H
acquires the signal while CONVST is low, and conversion begins on the rising edge of CONVST. The end-ofconversion signal (EOC) pulses low whenever a
conversion result becomes available for read. The endof-last-conversion signal (EOLC) goes low when the last
conversion result is available (Figure 7).
To start a conversion using external clock mode, pull
CONVST low for the acquisition time (tACQ). The T/H
acquires the signal while CONVST is low. The rising
edge of CONVST is the sampling instant. Apply an
external clock to CLK to start the conversion. To avoid
T/H droop degrading the sampled analog input signals,
22
the first CLK pulse must occur within 10µs from the
rising edge of CONVST. Additionally, the external clock
frequency must be greater than 100kHz to avoid T/H
droop-degrading accuracy. The first conversion result
is available for read when EOC goes low on the rising
edge of the 13th clock cycle. Subsequent conversion
results are available after every third clock cycle thereafter (Figures 8 and 9).
In both internal and external clock modes, hold
CONVST high until the last conversion result is read. If
CONVST goes low in the middle of a conversion, the
current conversion is aborted and a new conversion is
initiated. Furthermore, there must be a period of bus
inactivity (tQUIET) for 50ns or longer before the falling
edge of CONVST for the specified ADC performance.
______________________________________________________________________________________
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
tACQ
CONVST
HOLD
TRACK
CLK
TRACK
tCLK
tCNTC
1
2
3
12
tCLKH
13
14
tCLKL
15
16
17
tNEXT
tEOCD
18
19
1
tEOCD
EOC
tCONV
tEOC
tEOLCD
tCVEOLCD
EOLC
tQUIET ≥ 50ns
CS*
tCTR
tRTC
tRDH
RD
tACC
tRDL
CH3
D0–D11
CH7
tREQ
*CS CAN BE LOW AT ALL TIMES, LOW DURING THE RD CYCLES, OR THE SAME AS RD.
Figure 8. Read During Conversion—Channel 3 and Channel 7 Selected, External Clock
Reading a Conversion Result
Reading During a Conversion
Figures 7 and 8 show the interface signals to initiate a
read operation during a conversion cycle. These figures
show two channels selected for conversion. If more
channels are selected, the results are available successively at every EOC falling edge. CS can be low at all
times, low during the RD cycles, or the same as RD.
After initiating a conversion by bringing CONVST high,
wait for EOC to go low. In internal clock mode, EOC
goes low within 900ns. In external clock mode, EOC
goes low on the rising edge of the 13th CLK cycle. To
read the conversion result, drive CS and RD low to
latch data to the parallel digital output bus. Bring RD
high to release the digital bus. In internal clock mode,
the next EOC falling edge occurs within 225ns. In external clock mode, the next EOC falling edge occurs in
three CLK cycles. When the last result is available
EOLC goes low.
Reading After Conversion
Figure 9 shows the interface signals for a read operation
after a conversion with all eight channels enabled. At
the falling of EOLC, driving CS and RD low places the
first conversion result onto the parallel bus. Successive
low pulses of RD place the successive conversion
results onto the bus. When the last conversion results in
the sequence are read, additional read pulses wrap the
pointer back to the first converted result.
______________________________________________________________________________________
23
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
SAMPLE
INSTANT
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
CONVST
EOC
ONLY LAST PULSE SHOWN
tCVEOLCD
tEOC
EOLC
CS*
tRTC
tCTR
tRDL
tRDH
tQUIET1 = 50ns
RD
D0–D11
CH0
tACC
CH1
CH2
CH3
CH4
CH5
CH6
CH7
tREQ
* CS CAN BE LOW AT ALL TIMES, LOW DURING THE RD CYCLES, OR THE SAME AS RD.
Figure 9. Read After Conversion—Eight Channels Selected, External Clock
Power-Up Reset
At power-up, all channels are selected for conversion
(see the Configuration Register section). After applying
power, allow the 1ms wake-up time to elapse and then
initiate a dummy conversion and discard the results.
After the dummy conversion is complete, accurate conversions can be obtained.
Power-Saving Modes
Shutdown Mode
During shutdown the internal reference and analog
circuits in the device shutdown and the analog supply
current drops to 0.6µA (typ). Select shutdown mode
using the SHDN input. Set SHDN high to enter shutdown mode. SHDN takes precedence over CHSHDN.
Entering and exiting shutdown mode does not change
the configuration byte. However, a new configuration
byte can be written while in shutdown mode by following the standard write procedure shown in Figure 6.
EOC and EOLC are high when the MAX1304–MAX1306/
MAX1308–MAX1310/MAX1312–MAX1314 are shut down.
The state of the digital outputs D0–D11 is independent
of the state of SHDN. If CS and RD are low, the digital
outputs D0–D11 are active regardless of SHDN. The
digital outputs only go high impedance when CS or RD
is high. When the digital outputs are powered down, the
digital supply current drops to 20nA.
24
Exiting shutdown (falling edge of SHDN) starts a conversion in the same way as the rising edge of CONVST.
After coming out of shutdown, initiate a dummy conversion and discard the results. After the dummy conversion, allow the 1ms wake-up time to expire before
initiating the first accurate conversion.
Channel Shutdown (CHSHDN)
The channel-shutdown feature allows analog input
channels to be powered down when they are not
selected for conversion. Powering down channels that
are not selected for conversion reduces the analog
supply current by 2.9mA per channel. To power down
channels that are not selected for conversion, pull
CHSHDN low. See the Configuration Register section
for information on selecting and deselecting channels
for conversion.
The drawback of powering down analog inputs that are
not selected for conversion is that it takes time to power
them up. Figure 10 shows how a dummy conversion is
used to power up an analog input in external clock
mode. After selecting a new channel in the configuration register, initiate a dummy conversion and discard
the results. After the dummy conversion, allow the 1ms
wake-up time (tWAKE) to expire before initiating the first
accurate conversion.
______________________________________________________________________________________
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
CS*
tACQ
tACQ
CONVST
CONFIGURATION
REGISTER
UPDATES
DUMMY
CONVERSION
START
FIRST ACCURATE
CONVERSION
START
WR
CONFIGURATION REGISTER
POWERS UP ONE OR
MORE CHANNELS
D0–D7
DATA
IN
tWAKE ≥ 1ms
1
2
3
4
5
12
13
1
CLK
EOC
EOLC
*CS CAN BE LOW AT ALL TIMES, LOW DURING THE RD CYCLES, OR THE SAME AS RD.
Figure 10. Powering Up an Analog Input Channel with a Dummy Conversion and Wake-Up Time (CHSHDN = 0, External-Clock
Mode, One Channel Selected)
CS*
tACQ
tACQ
CONVST
CONFIGURATION
REGISTER
UPDATES
FIRST ACCURATE
CONVERSION START
SECOND ACCURATE
CONVERSION START
WR
CONFIGURATION REGISTER
POWERS UP ONE OR
MORE CHANNELS
D0–D7
DATA
IN
1
2
3
4
5
12
13
1
CLK
EOC
EOLC
*CS CAN BE LOW AT ALL TIMES, LOW DURING THE RD CYCLES, OR THE SAME AS RD.
Figure 11. Powering Up an Analog Input Channel Directly (CHSHDN = 1, External-Clock Mode, One Channel Selected)
______________________________________________________________________________________
25
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
To avoid the timing requirements associated with powering up an analog channel, force CHSHDN high. With
CHSHDN high, each analog input is powered up
regardless of whether it is selected for conversion in
the configuration register. Note that shutdown mode
takes precedence over the CHSHDN mode.
erence voltage by driving REF with a +2.0V to +3.0V
external reference. As shown in Figure 2, the REF input
impedance is 5kΩ. For more information about using
external references see the Transfer Functions section.
Midscale Voltage (MSV)
The voltage at MSV (VMSV) sets the midpoint of the ADC
transfer functions. For the 0 to +5V input range (unipolar
devices), the midpoint of the transfer function is +2.5V.
For the ±5V and ±10V input range devices, the midpoint
of the transfer function is zero.
As shown in Figure 2, there is a unity-gain buffer
between REFMS and MSV in the unipolar MAX1304/
MAX1305/MAX1306. This midscale buffer sets the midpoint of the unipolar transfer functions to either the internal +2.5V reference or an externally applied voltage at
REFMS. VMSV follows VREFMS within ±3mV.
The midscale buffer is not active for the bipolar
devices. For these devices, MSV must be connected to
AGND or externally driven. REFMS must be bypassed
with a 0.01µF capacitor to AGND.
See the Transfer Functions section for more information
about MSV.
Reference
Internal Reference
The internal reference circuits provide for analog input
voltages of 0 to +5V for the unipolar MAX1304/
MAX1305/MAX1306, ±5V for the bipolar MAX1308/
MAX1309/MAX1310 or ±10V for the bipolar MAX1312/
MAX1313/MAX1314. Install external capacitors for reference stability, as indicated in Table 3 and shown in
Figures 3 and 4.
As illustrated in Figure 2, the internal reference voltage
is 2.5V (VREF). This 2.5V is internally buffered to create
the voltages at REF+ and REF-. Table 4 shows the voltages at COM, REF+, and REF-.
External Reference
External reference operation is achieved by overriding
the internal reference voltage. Override the internal ref-
Table 3. Reference Bypass Capacitors
INPUT VOLTAGE RANGE
LOCATION
UNIPOLAR (µF)
BIPOLAR (µF)
2.2 || 0.1
N/A
REFMS Bypass Capacitor to AGND
0.01
0.01
REF Bypass Capacitor to AGND
0.01
0.01
REF+ Bypass Capacitor to AGND
0.1
0.1
2.2 || 0.1
2.2 || 0.1
MSV Bypass Capacitor to AGND
REF+ to REF- Capacitor
REF- Bypass Capacitor to AGND
0.1
0.1
COM Bypass Capacitor to AGND
2.2 || 0.1
2.2 || 0.1
N/A = Not applicable. Connect MSV directly to AGND.
Table 4. Reference Voltages
PARAMETER
EQUATION
CALCULATED VALUE (V)
VREF = 2.000V,
AVDD = 5.0V
CALCULATED VALUE (V)
VREF = 2.500V,
AVDD = 5.0V
CALCULATED VALUE (V)
VREF = 3.000V,
AVDD = 5.0V
VCOM
VCOM = 13 / 25 x AVDD
2.600
2.600
2.600
VREF+
VREF+ = VCOM + VREF / 2
3.600
3.850
4.100
VREF-
VREF- = VCOM - VREF / 2
1.600
1.350
1.100
VREF+ - VREF-
VREF- - VREF+ = VREF
2.000
2.500
3.000
26
(
)
(
)
(
______________________________________________________________________________________
)
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
Unipolar 0 to +5V Devices
Table 5 and Figure 12 show the offset binary transfer
function for the MAX1304/MAX1305/MAX1306 with a 0
to +5V input range. The full-scale input range (FSR) is
two times the voltage at REF. The internal +2.5V reference gives a +5V FSR, while an external +2V to +3V
reference allows an FSR of +4V to +6V, respectively.
Calculate the LSB size using:
1 LSB =
2 x VREF
212
The input range is centered about VMSV, internally set
to +2.5V. For a custom midscale voltage, drive REFMS
with an external voltage source and MSV will follow
REFMS. Noise present on MSV or REFMS directly couples into the ADC result. Use a precision, low-drift voltage reference with adequate bypassing to prevent MSV
from degrading ADC performance. For maximum FSR,
do not violate the absolute maximum voltage ratings of
the analog inputs when choosing MSV.
Determine the input voltage as a function of V REF ,
VMSV, and the output code in decimal using:
VCH_ = LSB x CODE10 + VMSV - 2.500V
which equals 1.22mV when using a 2.5V reference.
Table 5. 0 to 5V Unipolar Code Table
BINARY
DIGITAL
OUTPUT CODE
DECIMAL
EQUIVALENT
DIGITAL OUTPUT
CODE
(CODE10)
1111 1111 1111
= 0xFFF
4095
+4.9994 ± 0.5 LSB
1111 1111 1110
= 0xFFE
4094
+4.9982 ± 0.5 LSB
1000 0000 0001
= 0x801
2049
+2.5018 ± 0.5 LSB
1000 0000 0000
= 0x800
2048
+2.5006 ± 0.5 LSB
0111 1111 1111
= 0x7FF
2047
+2.4994 ± 0.5 LSB
0000 0000 0001
= 0x001
1
+0.0018 ± 0.5 LSB
0000 0000 0000
= 0x000
0
+0.0006 ± 0.5 LSB
INPUT VOLTAGE
(V)
VREF = +2.5V
VREFMS = +2.5V
)
BINARY OUTPUT CODE
(
2 x VREF
0xFFF
0xFFE
0xFFD
0xFFC
0x801
0x800
0x7FF
0x0003
0x0002
0x0001
0x0000
1 LSB =
2 x VREF
12
2
0
1 2 3
2046
2048 2050
(MSV)
4093
4095
INPUT VOLTAGE (LSBs)
Figure 12. 0 to +5V Unipolar Transfer Function
______________________________________________________________________________________
27
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
Transfer Functions
Bipolar ±5V Devices
Table 6 and Figure 13 show the two’s complement transfer function for the ±5V input range MAX1308/MAX1309/
MAX1310. The FSR is four times the voltage at REF. The
internal +2.5V reference gives a +10V FSR, while an
external +2V to +3V reference allows an FSR of +8V to
+12V respectively. Calculate the LSB size using:
1 LSB =
4 x VREF
212
which equals 2.44mV when using a 2.5V reference.
The input range is centered about V MSV. Normally,
MSV = AGND, and the input is symmetrical about zero.
For a custom midscale voltage, drive MSV with an
external voltage source. Noise present on MSV directly
couples into the ADC result. Use a precision, low-drift
voltage reference with adequate bypassing to prevent
MSV from degrading ADC performance. For maximum
FSR, do not violate the absolute maximum voltage ratings of the analog inputs when choosing MSV.
Determine the input voltage as a function of V REF ,
VMSV, and the output code in decimal using:
VCH_ = LSB x CODE10 + VMSV
Table 6. ±5V Bipolar Code Table
TWO’s
COMPLEMENT
DIGITAL OUTPUT
CODE
DECIMAL
EQUIVALENT
DIGITAL OUTPUT
CODE
(CODE10)
0111 1111 1111 =
0x7FF
+2047
+4.9988 ± 0.5 LSB
0111 1111 1110 =
0x7FE
+2046
+4.9963 ± 0.5 LSB
0000 0000 0001 =
0x001
+1
+0.0037 ± 0.5 LSB
0000 0000 0000 =
0x000
0
+0.0012 ± 0.5 LSB
1111 1111 1111 =
0xFFF
-1
-0.0012 ± 0.5 LSB
1000 0000 0001 =
0x801
-2047
-4.9963 ± 0.5 LSB
1000 0000 0000 =
0x800
-2048
-4.9988 ± 0.5 LSB
INPUT VOLTAGE
(V)
VREF = +2.5V
VMSV = 0
(
)
4 x VREF
TWO'S COMPLEMENT BINARY OUTPUT CODE
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
0x7FF
0x7FE
0x7FD
0x7FC
0x001
0x000
0xFFF
0x803
0x802
0x801
0x800
1 LSB =
-2048 -2046
-1 0 +1
(MSV)
28
______________________________________________________________________________________
212
+2045 +2047
INPUT VOLTAGE (VCH_ - VMSV IN LSBs)
Figure 13. ±5V Bipolar Transfer Function
4 x VREF
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
1 LSB =
8 x VREF
212
which equals 4.88mV with a +2.5V internal reference.
The input range is centered about V MSV. Normally,
MSV = AGND, and the input is symmetrical about zero.
For a custom midscale voltage, drive MSV with an
external voltage source. Noise present on MSV directly
couples into the ADC result. Use a precision, low-drift
voltage reference with adequate bypassing to prevent
MSV from degrading ADC performance. For maximum
FSR, do not violate the absolute maximum voltage ratings of the analog inputs when choosing MSV.
Determine the input voltage as a function of V REF ,
VMSV, and the output code in decimal using:
VCH_ = LSB x CODE10 + VMSV
Table 7. ±10V Bipolar Code Table
DECIMAL
EQUIVALENT
DIGITAL OUTPUT
CODE
(CODE10)
INPUT VOLTAGE
(V)
VREF = +2.5V
VMSV = 0
0111 1111 1111 =
0x7FF
+2047
+9.9976 ± 0.5 LSB
0111 1111 1110 =
0x7FE
+2046
+9.9927 ± 0.5 LSB
0000 0000 0001 =
0x001
+1
+0.0073 ± 0.5 LSB
0000 0000 0000 =
0x000
0
0.0024 ± 0.5 LSB
(
)
1111 1111 1111 =
0xFFF
-1
-0.0024 ± 0.5 LSB
1000 0000 0001 =
0x801
-2047
-9.9927 ± 0.5 LSB
1000 0000 0000 =
0x800
-2048
-9.9976 ± 0.5 LSB
8 x VREF
TWO'S COMPLEMENT BINARY OUTPUT CODE
TWO’s
COMPLEMENT
DIGITAL OUTPUT
CODE
0x7FF
0x7FE
0x7FD
0x7FC
0x001
0x000
0xFFF
0x803
0x802
0x801
0x800
1 LSB =
-2048 -2046
-1 0 +1
(MSV)
8 x VREF
212
+2045 +2047
INPUT VOLTAGE (VCH_ - VMSV IN LSBs)
Figure 14. ±10V Bipolar Transfer Function
______________________________________________________________________________________
29
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
Bipolar ±10V Devices
Table 7 and Figure 14 show the two’s complement transfer function for the ±10V input range MAX1312/
MAX1313/MAX1314. The FSR is eight times the voltage at
REF. The internal +2.5V reference gives a +20V FSR,
while an external +2V to +3V reference allows an FSR of
+16V to +24V, respectively. Calculate the LSB size using:
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
3-Phase Motor Controller
The MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–
MAX1314 are ideally suited for motor-control systems
(Figure 15). The devices’ simultaneously sampled
inputs eliminate the need for complicated DSP algo-
rithms that realign sequentially sampled data into a
simultaneous sample set. Additionally, the variety of
input voltage ranges allows for flexibility when choosing
current sensors and position encoders.
MAX1308
DSP
12-BIT
ADC
T/H
IGBT CURRENT DRIVERS
IPHASE3
CURRENT
SENSOR
IPHASE1
IPHASE2
3-PHASE ELECTRIC MOTOR
PHASE 1
PHASE 3
PHASE 2
POSITION
ENCODER
Figure 15. 3-Phase Motor Control
30
______________________________________________________________________________________
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
ously sampled eight channels eliminate the need for
complicated DSP algorithms that realign sequentially
sampled data into a simultaneous sample set.
MAX1312
T/H
12-BIT
ADC
MICROCONTROLLER
BUFFERS
AND INPUT
PROTECTION
VP3
VP1
VNEUTRAL
VP2
IP3
IP2
IPn
IP1
CURRENT
TRANSFORMER
PHASE 1
LOAD
POWER
GRID
NEUTRAL
CURRENT
TRANSFORMER
LOAD
LOAD
CURRENT
TRANSFORMER
PHASE 2
PHASE 3
CURRENT
TRANSFORMER
Figure 16. 3-Phase Power Monitoring
______________________________________________________________________________________
31
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
3-Phase Power-Monitoring System
The 8-channel devices are well suited for use in
3-phase power monitoring (Figure 16). The simultane-
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
Layout, Grounding, and Bypassing
For best performance use PC boards. Board layout must
ensure that digital and analog signal lines are separated
from each other. Do not run analog and digital lines parallel to one another (especially clock lines), and do not run
digital lines underneath the ADC package.
Figure 17 shows the recommended system ground connections. Establish an analog ground point at AGND and
a digital ground point at DGND. Connect all analog
grounds to the analog ground point. Connect all digital
grounds to the digital ground point. For lowest noise
operation, make the power-supply ground returns as low
impedance and as short as possible. Connect the analog
ground point to the digital ground point at one location.
High-frequency noise in the power supplies degrades
the ADC’s performance. Bypass the analog power
plane to the analog ground plane with a 2.2µF capacitor within one inch of the device. Bypass each AVDD to
AGND pair of pins with a 0.1µF capacitor as close to
the device as possible. AVDD to AGND pairs are pin 1
to pin 2, pin 14 to pin 15, and pin 16 to pin 17.
Likewise, bypass the digital power plane to the digital
ground plane with a 2.2µF capacitor within one inch of
the device. Bypass each DVDD to DGND pair of pins
with a 0.1µF capacitor as close to the device as possible. DVDD to DGND pairs are pin 24 to pin 25, and pin
38 to pin 39. If a supply is very noisy use a ferrite bead
as a lowpass filter as shown in Figure 17.
Definitions
Integral Nonlinearity (INL)
INL is the deviation of the values on an actual transfer
function from a straight line. For these devices, this
straight line is drawn between the endpoints of the
transfer function, once offset and gain errors have
been nullified.
Differential Nonlinearity (DNL)
DNL is the difference between an actual step width and
the ideal value of 1 LSB. For these devices, the DNL of
each digital output code is measured and the worstcase value is reported in the electrical characteristics
table. A DNL error specification of less than ±1 LSB
guarantees no missing codes and a monotonic
transfer function.
32
ANALOG SUPPLY
+5V
RETURN
DIGITAL
GROUND
POINT
DIGITAL SUPPLY
RETURN +3V TO +5V
OPTIONAL ANALOG
GROUND
FERRITE
POINT
BEAD
AVDD
AGND
DGND
MAX1304–MAX1306
MAX1308–MAX1310
MAX1312–MAX1314
DGND
DVDD
DATA
DVDD
DIGITAL
CIRCUITRY
Figure 17. Power-Supply Grounding and Bypassing
Offset Error
Offset error is a figure of merit that indicates how well
the actual transfer function matches the ideal transfer
function at a single point. Typically the point at which
offset error is specified is either at or near the zeroscale point of the transfer function or at or near the midscale point of the transfer function.
For the unipolar devices (MAX1304/MAX1305/
MAX1306), the ideal zero-scale transition from 0x000 to
0x001 occurs at 1 LSB above AGND (Figure 12, Table 5).
Unipolar offset error is the amount of deviation between
the measured zero-scale transition point and the ideal
zero-scale transition point.
For the bipolar devices (MAX1308/MAX1309/MAX1310/
MAX1312/MAX1313/MAX1314), the ideal midscale transition from 0xFFF to 0x000 occurs at MSV (Figures 14
and 13, Tables 7 and 6). The bipolar offset error is the
amount of deviation between the measured midscale
transition point and the ideal midscale transition point.
______________________________________________________________________________________
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
Effective Number of Bits (ENOB)
ENOB specifies the dynamic performance of an ADC at
a specific input frequency and sampling rate. An ideal
ADC’s error consists of quantization noise only. ENOB for
a full-scale sinusoidal input waveform is computed as:
For the unipolar devices (MAX1304/MAX1305/
MAX1306), the full-scale transition point is from 0xFFE
to 0xFFF and the zero-scale transition point is from
0x000 to 0x001.
For the bipolar devices (MAX1308/MAX1309/MAX1310/
MAX1312/MAX1313/MAX1314), the full-scale transition
point is from 0x7FE to 0x7FF and the zero-scale transition point is from 0x800 to 0x801.
Signal-to-Noise Ratio (SNR)
For a waveform perfectly reconstructed from digital
samples, the theoretical maximum SNR is the ratio of
the full-scale analog input (RMS value) to the RMS
quantization error (residual error). The ideal, theoretical
minimum analog-to-digital noise is caused by quantization error only and results directly from the ADC’s resolution (N bits):
SNRdB[max] = 6.02dB × N + 1.76dB
In reality, there are other noise sources such as thermal
noise, reference noise, and clock jitter.
For these devices, SNR is computed by taking the ratio
of the RMS signal to the RMS noise. RMS noise
includes all spectral components to the Nyquist frequency excluding the fundamental, the first five harmonics, and the DC offset.
Signal-to-Noise Plus Distortion (SINAD)
SINAD is computed by taking the ratio of the RMS signal
to the RMS noise plus distortion. RMS noise plus distortion includes all spectral components to the Nyquist frequency excluding the fundamental and the DC offset.
ENOB =
SINAD − 1.76
6.02
Total Harmonic Distortion (THD)
THD is the ratio of the RMS sum of the first five harmonics to the fundamental itself. This is expressed as:
⎛ V22 + V32 + V 2 + V52 + V62 ⎞
4
THD = 20 x log ⎜
⎟
⎜
⎟
V
1
⎝
⎠
where V1 is the fundamental amplitude, and V2 through
V 6 are the amplitudes of the 2nd- through 6thorder harmonics.
Spurious-Free Dynamic Range (SFDR)
SFDR is the ratio of the RMS amplitude of the fundamental (maximum signal component) to the RMS value of the
next largest spurious component, excluding DC offset.
SFDR is specified in decibels relative to the carrier (dBc).
Channel-to-Channel Isolation
Channel-to-channel isolation indicates how well each
analog input is isolated from the others. The channel-tochannel isolation for these devices is measured by
applying DC to channel 1 through channel 7 while an
AC 500kHz, -0.4dBFS sine wave is applied to channel
0. An FFT is taken for channel 0 and channel 1 and the
difference (in dB) of the 500kHz magnitudes is reported
as the channel-to-channel isolation.
Aperature Delay
Aperture delay (tAD) is the time delay from the CONVST
rising edge to the instant when an actual sample is taken.
⎛
⎞
SIGNALRMS
SINAD(dB) = 20 x log ⎜
⎟
⎝ (NOISE + DISTORTION)RMS ⎠
______________________________________________________________________________________
33
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
Gain Error
Gain error is a figure of merit that indicates how well the
slope of the actual transfer function matches the slope
of the ideal transfer function. For the MAX1304–
MAX1306/MAX1308–MAX1310/MAX1312–MAX1314, the
gain error is the difference of the measured full-scale
and zero-scale transition points minus the difference of
the ideal full-scale and zero-scale transition points.
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
Aperture Jitter
Small-Signal Bandwidth
Aperture Jitter (tAJ) is the sample-to-sample variation in
aperture delay.
A small -20dBFS analog input signal is applied to an
ADC so that the signal’s slew rate does not limit the
ADC’s performance. The input frequency is then swept
up to the point where the amplitude of the digitized
conversion result has decreased by -3dB.
Jitter is a concern when considering an ADC’s dynamic
performance, e.g., SNR. To reconstruct an analog input
from the ADC digital outputs, it is critical to know the
time at which each sample was taken. Typical applications use an accurate sampling clock signal that has
low jitter from sampling edge to sampling edge. For a
system with a perfect sampling clock signal, with no
clock jitter, the SNR performance of an ADC is limited
by the ADC’s internal aperture jitter as follows:
⎛
⎞
1
SNR = 20 x log ⎜
⎟
⎝ 2 x π x fIN x tAJ ⎠
where fIN represents the analog input frequency and
tAJ is the time of the aperture jitter.
34
Full-Power Bandwidth
A large, -0.5dBFS analog input signal is applied to an
ADC, and the input frequency is swept up to the point
where the amplitude of the digitized conversion result
has decreased by -3dB. This point is defined as fullpower input bandwidth frequency.
DC Power-Supply Rejection (PSRR)
DC PSRR is defined as the change in the positive fullscale transfer function point caused by a ±5% variation
in the analog power-supply voltage (AVDD).
______________________________________________________________________________________
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
8
30
29
D11
37
38
39
40
41
42
43
44
45
46
CHSHDN
SHDN
CLK
CONVST
CS
WR
RD
EOLC
EOC
DGND
DVDD
47
48
32
6
31
MAX1305
MAX1309
MAX1313
7
8
30
29
28
10
27
11
26
12
25
INTCLK/EXTCLK
AGND
AVDD
AGND
AVDD
REFMS
13
9
24
23
22
21
5
REFMS
REF
REF+
COM
REFAGND
DGND
INTCLK/EXTCLK
AGND
AVDD
AGND
AVDD
20
25
19
12
18
26
17
11
16
27
15
10
14
28
D8
D7
D6
D5
D4
D3
D2
D1
D0
DVDD
4-CHANNEL TQFP
37
38
39
40
41
42
43
44
45
46
47
48
CHSHDN
SHDN
CLK
CONVST
CS
WR
RD
EOLC
EOC
DGND
DVDD
D11
8-CHANNEL TQFP
AVDD
1
36
AGND
2
35
AGND
3
34
CH0
CH1
MSV
I.C.
4
33
5
32
6
31
I.C.
8
I.C.
I.C.
I.C.
I.C.
9
28
10
27
11
26
12
25
30
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
DVDD
24
23
22
19
REF
REF+
COM
REFAGND
DGND
21
18
REFMS
29
17
16
15
14
13
20
MAX1306
MAX1310
MAX1314
7
INTCLK/EXTCLK
AGND
AVDD
AGND
AVDD
13
9
33
D10
D9
24
MAX1304
MAX1308
MAX1312
7
34
4
23
31
3
CH0
CH1
MSV
CH2
CH3
I.C.
I.C.
I.C.
I.C.
22
32
6
35
21
5
D8
D7
D6
D5
D4
D3
D2
D1
D0
DVDD
36
2
20
33
1
19
34
4
AVDD
AGND
AGND
REF
REF+
COM
REFAGND
DGND
3
CH0
CH1
MSV
CH2
CH3
CH4
CH5
CH6
CH7
D10
D9
18
35
17
36
2
16
1
15
AVDD
AGND
AGND
14
D11
37
38
39
40
41
42
43
44
45
46
CHSHDN
SHDN
CLK
CONVST
CS
WR
RD
EOLC
EOC
DGND
DVDD
47
48
TOP VIEW
2-CHANNEL TQFP
______________________________________________________________________________________
35
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
Pin Configurations
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
Package Information
Chip Information
TRANSISTOR COUNT: 50,000
PROCESS: 0.6µm BiCMOS
36
For the latest package outline information and land patterns, go
to www.maxim-ic.com/packages.
PACKAGE TYPE
PACKAGE CODE
DOCUMENT NO.
48 TQFP
C48+6
21-0054
______________________________________________________________________________________
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
REVISION
NUMBER
REVISION
DATE
4
8/09
DESCRIPTION
Added automotive part numbers
PAGES
CHANGED
1
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 37
© 2009 Maxim Integrated Products
Maxim is a registered trademark of Maxim Integrated Products, Inc.
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
Revision History