Embedded Power for Business-Critical Continuity Rev.02.16.07 NFS110 Series 1 of 4 NFS110 Series Single and quad output Total Power: 80 - 110W Input Voltage: 85 - 264VAC 120 - 370VDC # of Outputs: Single, quad Special Features • 7.0 x 4.25 x 1.8 inch package • Overvoltage and short circuit protection • 110 W with 20 CFM • Adjustable outputs • EN55022, EN55011 conducted emissions level B • UL, VDE and CSA safety approvals • CE mark • Available RoHS compliant • 2 year warranty Safety VDE0805/EN60950/ IEC950/IEC1010 File No. 10401-3336-0213 Licence No. 40014677 UL1950 File No. E136005 CSA C22.2 No. 950 File No. LR41062C The NFS110 series is a 110 W universal input ac-dc power supply on a 7 x 4.25 inch card. The NFS110 series has four single and three quad output models and has proven itself to be highly reliable and versatile product for a wide range of communication and industrial applications, with a very high peak current capability on each output for drive and motor applications. The NFS110 provides 80 W of output power with free air convection cooling which can be boosted to 110 W with 20 CFM of air. Standard features include overvoltage and short circuit protection. The series, with full international safety approval and the CE mark, meets conducted emissions EN55022 level B. The NFS110 series is designed for use in low power data networking, computer, telecom and industrial applications such as servers, thermal printers, storage devices, vending machines and POS equipment. Embedded Power for Business-Critical Continuity Rev.02.16.07 NFS110 Series 2 of 4 Specifications All specifications are typical at nominal input, full load at 25°C unless otherwise stated OUTPUT SPECIFICATIONS GENERAL SPECIFICATIONS Voltage adjustability +5.1 V o/p on multi’s 5.1 V single output 12 V single output 15 V single output 24 V single output Line regulation LL to HL, FL All outputs on all units Overshoot/undershoot At turn-on 0% Temperature coefficient All outputs ±0.02%/°C Overvoltage protection Multi o/p 5.1 V only 5.1 V single 12 V single 15 V single 24 V single Output power limit Primary power limited Minimum output current (See Note 13) Short circuit protection ±3.0% ±3.0% 12-14 V 15-18 V 24-30 V Hold-up time 110 Vac @ 80 W 110 Vac @ 110 W 230 Vac @ 80 W 230 Vac @ 110 W Efficiency Multiple outputs +5.1 V single 12 V and 15 V singles 24 V single Isolation voltage Input/output Input/chassis Switching frequency At 100 Watts output At zero load ±0.1% max. 6.25 V ±0.75 V 6.25 V ±0.75 V 15.75 V ±1.0 V 22 V ±1.5 V 33 V ±2.5 V Pin max. 160 W Pout min. 110 W Approvals and standards (See Note 12) 70% typical 70% typical 72% typical 75% typical 3000 Vac 1500 Vac 20-70 kHz 100-250 kHz VDE0805, EN60950, IEC950 IEC1010, UL1950 CSA C22.2 No. 950 Weight Singles Multiple outputs 550 g (19.4 oz) 600 g (21.2 oz) MTBF (See Note 9) MIL-HDBK-217E 125,000 hours 0A Burst mode operation 35 ms 17 ms 140 ms 100 ms ENVIRONMENTAL SPECIFICATIONS INPUT SPECIFICATIONS Input voltage range 85-264 Vac 120-370 Vdc Input frequency range Thermal performance (See Notes 9, 10) 47-440 Hz Input surge current 230 Vac 35 A Safety ground leakage current 110 Vac, 50 Hz 230 Vac, 50 Hz 0.2 mA, max. 0.4 mA, max. EN55022, FCC part 15 EN55022, FCC part 15 EN61000-4-2, level 3 EN61000-4-2, level 4 EN61000-4-5, level 3 EN61000-4-4, level 3 EN61000-4-3, level 3 EN61000-4-6, level 3 Level B Level A Perf. criteria 1 Perf. criteria 1 Perf. criteria 1 Perf. criteria 1 Perf. criteria 2 Perf. criteria 1 EMC CHARACTERISTICS Conducted emissions Radiated emissions ESD air ESD contact Surge Fast transients Radiated immunity Conducted immunity Operating, see curve 0 °C to +70 °C Non-operating –40 °C to +85 °C 0 °C to +50 °C, 80 W amb. convection cooled +50 °C to +70 °C, Derate 2 W/°C amb. convection cooled 0 °C to +50 °C, 110 W 20 CFM forced air +50 °C to +70 °C, Derate 20 CFM forced air 2.75 W/°C Peak, 0 °C to +50 °C, 110 W max. 60 seconds Relative humidity Non-condensing Altitude Operating Non-operating Vibration (See Note 11) 5-500 Hz 5% to 95% RH 10,000 feet max. 40,000 feet max. 2.4 G approx. Embedded Power for Business-Critical Continuity Rev.02.16.07 NFS110 Series 3 of 4 Specifications Contd. OUTPUT CURRENTS OUTPUT VOLTAGE MAX (1) PEAK (2) FAN (3) RIPPLE (4) TOTAL REGULATION (5) MODEL NUMBERS (13,14,F) +5.1 V 8A 20 A 10 A 50 mV ±2.0% NFS110-7601PJ +12 V 4.5 A 9A 5A 120 mV ±3.0% –12 V 0.5 A 1.5 A 1A 120 mV ±3.0% –5 V 0.5 A 1.5 A 1A 50 mV ±3.0% +5.1 V (IA) 8A 20 A 10 A 50 mV ±2.0% +24 V (IB) (6) 3.5 A 4.5 A 4.5 A 240 mV +10/–5.0% +12 V 4.5 A 9A 5A 120 mV ±3.0% –12 V 0.5 A 1.5 A 1A 120 mV ±3.0% +5.1 V 8A 20 A 10 A 50 mV ±2.0% 3 4 5 6 7 8 9 10 11 12 13 14 15 NFS110-7604PJ +15 V 4A 7.5 A 5A 150 mV ±3.0% –15 V 0.5 A 1.5 A 1A 150 mV ±3.0% –5 V 0.5 A 1.5 A 1A 50 mV ±3.0% 5.1 V 16 A 22 A 20 A 50 mV ±2.0% NFS110-7605J (7,8) 12 V 7A 9A 9A 120 mV ±2.0% NFS110-7612J (7,8) 15 V 5A 7.3 A 7.3 A 150 mV ±2.0% NFS110-7615J (7,8) 24 V 3.5 A 4.5 A 4.5 A 240 mV ±2.0% NFS110-7624J (7,8) Notes 1 2 NFS110-7602PJ (6) Convection cooled, 80 W maximum. Peak outputs lasting less than 60 seconds with duty cycle less than 10%. Total peak power must not exceed 110 W. Forced air, 20 CFM at 1 atmosphere, 110 W maximum. Figure is peak-to-peak. Output ripple is measured across a 50 MHz bandwidth using a 12 inch twisted pair terminated with a 47 μF capacitor. Total regulation is defined as the static output regulation at 25 °C, including initial tolerance, line voltage within stated limits and output voltages adjusted to their factory settings. To achieve stated regulation on the 24 V output on the NFS110-7602PJ, the following load condition must be true: IA / IB ≤ 5, where: IA = +5.1 V output current, and IB = +24 V output current The +24 V output will maintain ±5.0% regulation under the following additional condition: IA ≤ 5 A. Single output models have floating outputs which may be referenced as either positive or negative. Higher voltage supplies may be adjusted over a wide output voltage range, as long as the total output power does not exceed 80 Watts (natural convection) or 110 Watts (forced air). Power fail detect not available on single output models. Derating curve is application specific for ambient temperatures >50 °C, for optimum reliability no part of the heatsink should exceed 90 ºC and no semiconductor case temperature should exceed 100 ºC. Caution: Allow a minimum of 1 second after disconnecting the power when making thermal measurements. Three orthogonal axes, random vibration, 10 minute test for each axis. This product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. Artesyn Technologies recommends a minimum load of 11 W to achieve the design MTBF. See the derating curve on page 3. The ‘J’ suffix indicates that these parts are Pb-free (RoHS 6/6) compliant. TSE RoHS 5/6 (non Pb-free) compliant versions may be available on special request, please contact your local sales representative for details. NOTICE: Some models do not support all options. Please contact your local Artesyn representative or use the on-line model number search tool at http://www.artesyn.com/powergroup/products.htm to find a suitable alternative. TRANSIENT RESPONSE NFS110-7601PJ +5.1 V (7.5 A to 10 A) +12 V (2.5 A to 5 A) -12 V (0.5 A to 1 A) -5 V (0.5 A to 1 A) NFS110-7602PJ +5.1V (7.5 A to 10 A) +24 V (1.5 A to 3 A) +12 V (2.5 A to 5 A) -12 V (0.5 A to 1 A) NFS110-7604PJ +5.1 V (7.5 A to 10 A) +15 V (2.5 A to 5 A) -15 V (0.5 A to 1 A) -5 V (0.5 A to 1 A) 150 mV peak, 1 ms recovery 100 mV peak, 0.5 ms recovery 100 mV peak, 0.5 ms recovery 100 mV peak, 0.5 ms recovery 150 mV peak, 1 ms recovery 300 mV peak, 1 ms recovery 100 mV peak, 0.5 ms recovery 100 mV peak, 0.5 ms recovery 150 mV peak, 1 ms recovery 100 mV peak, 0.5 ms recovery 100 mV peak, 0.5 ms recovery 100 mV peak, 0.5 ms recovery NFS110-7605J +5.1 V (10 A to 20 A) 250 mV peak, 1 ms recovery NFS110-7612J +12 V (4.5 A to 9 A) 360 mV peak, 1 ms recovery NFS110-7615J +15 V (3.65 A to 7.3 A) 450 mV peak, 1 ms recovery NFS110-7624J +24V (2.25 A to 4.5 A) 720 mV peak, 1 ms recovery Embedded Power for Business-Critical Continuity Rev.02.16.07 NFS110 Series 4 of 4 Americas 5810 Van Allen Way Carlsbad, CA 92008 USA Telephone: +1 760 930 4600 Facsimile: +1 760 930 0698 Europe (UK) Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom Telephone: +44 (0) 1384 842 211 Facsimile: +44 (0) 1384 843 355 Asia (HK) 16th - 17th Floors, Lu Plaza 2 Wing Yip Street, Kwun Tong Kowloon, Hong Kong Telephone: +852 2176 3333 Facsimile: +852 2176 3888 For global contact, visit: www.powerconversion.com [email protected] While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Emerson Network Power. The global leader in enabling business-critical continuity. AC Power Connectivity DC Power Embedded Power Inbound Power Integrated Cabinet Solutions Outside Plant Precision Cooling Site Monitoring and Services EmersonNetworkPower. com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2007 Emerson Electric Co.