Kingbright AM2520SURCK08 Subminiature solid state lamp Datasheet

SUBMINIATURE SOLID STATE LAMP
AM2520SURCK08
Features
HYPER RED
Description
SUBMINIATURE PACKAGE.
The Hyper Red source color devices are made
WIDE VIEWING ANGLE.
with DH InGaAlP on GaAs substrate Light Emitting Diode.
YOKE LEAD.
LONG LIFE - SOLID STATE RELIABILITY.
LOW PACKAGE PROFILE.
PACKAGE : 1000PCS / REEL.
RoHS COMPLIANT.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Lead spacing is measured where the leads emerge from the package.
4. Specifications are subject to change without notice.
SPEC NO: DSAD1267
REV NO: V.2
DATE: MAR/05/2005
PAGE: 1 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: W.J.ZHU
ERP:1202000702
Selection Guide
Part No.
Dice
AM2520SURCK08
Iv (mcd)
@ 20 mA
Lens Type
HYPER RED (InGaAlP)
WATER CLEAR
Viewing
Angle
Min.
Typ.
2θ
θ1/2
180
650
20°
Note:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
λpeak
Peak Wavelength
Hyper Red
λD
Dominant Wavelength
∆λ1/2
Typ.
Max.
Units
Test Conditions
650
nm
IF=20mA
Hyper Red
635
nm
IF=20mA
Spectral Line Half-width
Hyper Red
28
nm
IF=20mA
C
Capacitance
Hyper Red
35
pF
VF=0V;f=1MHz
VF
Forward Voltage
Hyper Red
1.95
2.5
V
IF=20mA
IR
Reverse Current
Hyper Red
10
uA
VR = 5V
Absolute Maximum Ratings at TA=25°C
Parameter
Hyper Red
Units
Power dissipation
170
mW
DC Forward Current
30
mA
Peak Forward Current [1]
185
mA
5
V
Reverse Voltage
Operating / Storage Temperature
-40°C To +85°C
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAD1267
REV NO: V.2
DATE: MAR/05/2005
PAGE: 2 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: W.J.ZHU
ERP:1202000702
Hyper Red
AM2520SURCK08
SPEC NO: DSAD1267
REV NO: V.2
DATE: MAR/05/2005
PAGE: 3 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: W.J.ZHU
ERP:1202000702
AM2520SURCK08
Recommended Soldering Pattern
(Units : mm)
Tape Specifications
(Units : mm)
Remarks:
If there is sorting requirement (eg. forward voltage, luminous intensity or wavelength),the condition as follows:
1.Wavelength: +/-1nm (Test condition is based on the sorting standard).
2.Luminous intensity: +/-15% (Test condition is based on the sorting standard).
3.Forward voltage: +/-0.1V (Test condition is based on the sorting standard).
SPEC NO: DSAD1267
REV NO: V.2
DATE: MAR/05/2005
PAGE: 4 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: W.J.ZHU
ERP:1202000702
Similar pages