OPTEK OPB39T15 Slotted op ti cal switch Datasheet

Product Bulletin OPB380
August2005
1996
January
Slotted Optical Switches
Types OPB380, OPB390 Series
Features
Absolute Maximum Ratings (TA = 25o C unless otherwise noted)
• 0.125" (3.18 mm) wide gap
• 24" minimum, 26 AWG wire leads
• Choice of aperture
• Choice of opaque or IR transmissive
Storage and Operating Temperature Range . . . . . . . . . . . . . . . . . -40o C to +80o C(1)
shell material
• Choice of mounting configuration
• Choice of lead spacing
Description
The OPB380/390 series of slotted
switches provides the design engineer
with the flexibility of a custom device
from a standard product line. Building
from a standard housing with a 0.125"
(3.18 mm) wide slot, the user can specify
(1) electrical output parameters, (2)
mounting tab configuration, (3) discrete
shell material, and (4) aperture width.
All housings are an opaque grade of
injection-molded plastic to minimize the
assembly's sensitivity to ambient
radiation, both visible and near-infrared.
Discrete shells (exposed only on the
parallel faces inside the device throat)
are either IR transmissive plastic for
applications where aperture
contamination may occur or opaque
plastic with aperture openings for
maximum protection against ambient
light.
Input Diode
Forward DC Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA
Peak Forward Current (1 µs pulse width, 300 pps) . . . . . . . . . . . . . . . . . . . . . . . 3.0 A
Reverse DC Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0 V
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mW(1)
Output Phototransistor
Collector-Emitter Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 V
Emitter-Collector Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0 V
Collector DC Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 mA
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mW(1)
Notes:
(1) Derate linearly 1.82 mW/o C above 25o C (Maximum storage and operating temperature is
limited by the temperature rating of the lead wires)
(2) All parameters tested using pulse technique.
(3) The OPB380/OPB390 wire terminations are 24" of 7 strand, 26 AWG,UL1061
UL 1429 insulated wire
on each terminal. The devices incorporate a wire strain relief at the housing surface. The
insulation colors and functions are:
RED - IRED Anode
BLACK - IRED Cathode
WHITE - Phototransistor Collector
GREEN - Phototransistor Emitter
Other wire lengths and/or colors are available. Contact your local representative or call the
factory.
Replaces/Upgrades
OPB880/OPB890 Series
Optek Technology, Inc.
1215 W. Crosby Road
Carrollton, Texas 75006
12-12
(972) 323-2200
Fax (972) 323-2396
Types OPB380, OPB390 Series
Electrical Characteristics (TA = 25o C unless otherwise noted)
SYMBOL
Input Diode
PARAMETER
MIN MAX UNITS
TEST CONDITIONS
VF
Forward Voltage
1.7
V
IF = 20 mA
IR
Reverse Current
100
µA
VR = 2 V
Output Phototransistor
V(BR)CEO
Collector-Emitter Breakdown Voltage
30
V
IC = 1 mA
V(BR)ECO
Emitter-Collector Breakdown Voltage
5.0
V
IE = 100 µA
nA
VCE = 10 V, IF = 0, Ee = 0
ICEO
Collector-Emitter Dark Curreent
100
Coupled
IC(ON)
On-State Collector Current
OPB380T, N, L, P55
OPB390T, N, L, P55
3.5
14.0
mA
VCE = 0.4 V, IF = 20 mA
OPB380T, N, L, P51
OPB390T, N, L, P51
2.5
10.0
mA
VCE = 0.4 V, IF = 20 mA
OPB380T, N, L, P11
OPB390T, N, L, P11
1.0
5.0
mA
VCE = 0.4 V, IF = 20 mA
PART NUMBER GUIDE
OPB 3 X X X X X
Optek Assembly
Aperture Width In Front
of Sensor
5 = 0.050" 1 = 0.010"
Phototransistor Output
Family
Aperture Width In Front
of Emitter
5 = 0.050" 1= 0.010"
Discrete Shell Material
Designation
8 - Base Mount IR Transmissive
Plastic Discrete Shell
With Wire Termination
Mounting Configurations
9 - Base Mount Opaque
Plastic Discrete Shell
With Wire Termination
T -Both Mounting Tabs
N - No Mounting Tabs
L - Single Mounting Tab
Emitter Side
P - Single Mounting Tab
Phototransistor Side
Optek reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Optek Technology, Inc.
1215 W. Crosby Road
Carrollton, Texas 75006
(972) 323-2200
Fax (972) 323-2396
12-13
Types OPB380, OPB390 Series
Package N
Package T
GRAY/CLEAR TOP
DENOTES LED
GRAY/CLEAR TOP
Package P
Package L
GRAY/CLEAR TOP
DENOTES LED
GRAY/CLEAR TOP
DENOTES LED
Notes:
(1) Aperture dimensions dependent on part number. See Part Number Guide.
Optek Technology, Inc.
1215 W. Crosby Road
Carrollton, Texas 75006
12-14
(972) 323-2200
Fax (972) 323-2396
Types OPB380, OPB390 Series
Typical Performance Curves
Normalized Output Current vs
Forward Current
VCE = 0.4 V
Normalized to
IF = 20 mA
Normalized Output Current vs
Ambient Temperature
+2σ
Typ
-2σ
+2σ
+2σ
Typ
-2σ
Typ
+2σ
-2σ
Typ
VCE = 0.4 V
IF = 20 mA
Normalized
to
TA = 25o C
-2σ
TA - Ambient Temperature - o C
IF - Forward Current - mA
Rise and Fall Time vs
Load Resistance
IF = 20 mA (50% Duty
Cycle)
VCE = 0.4 V
Rise Time
Fall Time
RL - Load Resistance - Ω
All Part Numbers Ending in “1”
Normalized Output Current vs
Forward Current
Typ
IF = 20 mA (50% Duty
Cycle)
VCE = 0.4 V
-2σ
Rise Time
Fall Time
+2σ
+2σ
Typ
Rise and Fall Time vs
Load Resistance
VCE = 0.4 V
Normalized to
IF = 20 mA
-2σ
IF - Forward Current - mA
RL - Load Resistance - Ω
Optek reserves the right to make changes at any time in order to improve the design and to supply the best product possible.
Optek Technology, Inc.
1215 W. Crosby Road
Carrollton, Texas 75006
(972) 323-2200
Fax (972) 323-2396
12-15
Similar pages