NSC LM2672LD-12 Simple switcherâ® power converter high efficiency 1a step-down voltage regulator with feature Datasheet

LM2672
SIMPLE SWITCHER ® Power Converter High Efficiency
1A Step-Down Voltage Regulator with Features
General Description
The LM2672 series of regulators are monolithic integrated
circuits built with a LMDMOS process. These regulators
provide all the active functions for a step-down (buck)
switching regulator, capable of driving a 1A load current with
excellent line and load regulation. These devices are available in fixed output voltages of 3.3V, 5.0V, 12V, and an
adjustable output version.
Requiring a minimum number of external components, these
regulators are simple to use and include patented internal
frequency compensation (Patent Nos. 5,382,918 and
5,514,947), fixed frequency oscillator, external shutdown,
soft-start, and frequency synchronization.
The LM2672 series operates at a switching frequency of
260 kHz, thus allowing smaller sized filter components than
what would be needed with lower frequency switching regulators. Because of its very high efficiency ( > 90%), the copper traces on the printed circuit board are the only heat
sinking needed.
A family of standard inductors for use with the LM2672 are
available from several different manufacturers. This feature
greatly simplifies the design of switch-mode power supplies
using these advanced ICs. Also included in the datasheet
are selector guides for diodes and capacitors designed to
work in switch-mode power supplies.
Other features include a guaranteed ± 1.5% tolerance on
output voltage within specified input voltages and output
load conditions, and ± 10% on the oscillator frequency. External shutdown is included, featuring typically 50 µA
stand-by current. The output switch includes current limiting,
as well as thermal shutdown for full protection under fault
conditions.
Typical Application
To simplify the LM2672 buck regulator design procedure,
there exists computer design software, LM267X Made
Simple version 6.0.
Features
n Efficiency up to 96%
n Available in SO-8, 8-pin DIP and LLP packages
n Computer Design Software LM267X Made Simple
version 6.0
n Simple and easy to design with
n Requires only 5 external components
n Uses readily available standard inductors
n 3.3V, 5.0V, 12V, and adjustable output versions
n Adjustable version output voltage range: 1.21V to 37V
n ± 1.5% max output voltage tolerance over line and load
conditions
n Guaranteed 1A output load current
n 0.25Ω DMOS Output Switch
n Wide input voltage range: 8V to 40V
n 260 kHz fixed frequency internal oscillator
n TTL shutdown capability, low power standby mode
n Soft-start and frequency synchronization
n Thermal shutdown and current limit protection
Typical Applications
n Simple High Efficiency ( > 90%) Step-Down (Buck)
Regulator
n Efficient Pre-Regulator for Linear Regulators
(Fixed Output Voltage
Versions)
01293401
SIMPLE SWITCHER ® is a registered trademark of National Semiconductor Corporation.
Windows ® is a registered trademark of Microsoft Corporation.
© 2001 National Semiconductor Corporation
DS012934
www.national.com
LM2672 SIMPLE SWITCHER Power Converter High Efficiency 1A Step-Down Voltage Regulator
with Features
May 2001
LM2672
Connection Diagrams
16-Lead LLP Surface Mount Package
Top View
8-Lead Package
Top View
01293402
SO-8/DIP Package
See NSC Package Drawing Number MO8A/N08E
01293441
LLP Package
See NSC Package Drawing Number LDA16A
TABLE 1. Package Marking and Ordering Information
Output Voltage
Order Information
Package Marking
Supplied as:
12
LM2672LD-12
S0001B
1000 Units on Tape and Reel
16 Lead LLP
12
LM2672LDX-12
S0001B
4500 Units on Tape and Reel
3.3
LM2672LD-3.3
S0002B
1000 Units on Tape and Reel
3.3
LM2672LDX-3.3
S0002B
4500 Units on Tape and Reel
5.0
LM2672LD-5.0
S0003B
1000 Units on Tape and Reel
5.0
LM2672LDX-5.0
S0003B
4500 Units on Tape and Reel
ADJ
LM2672LD-ADJ
S0004B
1000 Units on Tape and Reel
ADJ
LM2672LDX-ADJ
S0004B
4500 Units on Tape and Reel
12
LM2672M-12
2672M-12
Shipped in Anti-Static Rails
12
LM2672MX-12
2672M-12
2500 Units on Tape and Reel
SO-8
3.3
LM2672M-3.3
2672M-3.3
Shipped in Anti-Static Rails
3.3
LM2672MX-3.3
2672M-3.3
2500 Units on Tape and Reel
5.0
LM2672M-5.0
2672M-5.0
Shipped in Anti-Static Rails
2500 Units on Tape and Reel
5.0
LM2672MX-5.0
2672M-5.0
ADJ
LM2672M-ADJ
2672M-ADJ
Shipped in Anti-Static Rails
ADJ
LM2672MX-ADJ
2672M-ADJ
2500 Units on Tape and Reel
DIP
12
LM2672N-12
LM2672N-12
Shipped in Anti-Static Rails
3.3
LM2672N-3.3
LM2672N-3.3
Shipped in Anti-Static Rails
5.0
LM2672N-5.0
LM2672N-5.0
Shipped in Anti-Static Rails
ADJ
LM2672N-ADJ
LM2672N-ADJ
Shipped in Anti-Static Rails
www.national.com
2
Lead Temperature
(Note 1)
M Package
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage
45V
Switch Voltage to Ground
+215˚C
Infrared (15s)
+220˚C
+260˚C
LLP Package (see AN-1187)
−1V
Boost Pin Voltage
Vapor Phase (60s)
N Package (Soldering, 10s)
−0.1V ≤ VSH ≤ 6V
ON/OFF Pin Voltage
LM2672
Absolute Maximum Ratings
Maximum Junction Temperature
+150˚C
VSW + 8V
−0.3V ≤ VFB ≤ 14V
Feedback Pin Voltage
Operating Ratings
ESD Susceptibility
Human Body Model (Note 2)
Supply Voltage
2 kV
Power Dissipation
Internally Limited
Storage Temperature Range
−65˚C to +150˚C
6.5V to 40V
−40˚C ≤ TJ ≤ +125˚C
Temperature Range
Electrical Characteristics
LM2672-3.3 Specifications with standard type face are for TJ = 25˚C, and those in bold type face apply over full
Operating Temperature Range.
Symbol
Parameter
Conditions
Typical
Min
Max
(Note 4)
(Note 5)
(Note 5)
Units
SYSTEM PARAMETERS Test Circuit Figure 2 (Note 3)
VOUT
Output Voltage
VIN = 8V to 40V, ILOAD = 20 mA to 1A
3.3
3.251/3.201
3.350/3.399
V
VOUT
Output Voltage
VIN = 6.5V to 40V, ILOAD = 20 mA to 500 mA
3.3
3.251/3.201
3.350/3.399
V
η
Efficiency
VIN = 12V, ILOAD = 1A
86
%
LM2672-5.0
Symbol
Parameter
Conditions
Typical
Min
Max
(Note 4)
(Note 5)
(Note 5)
Units
SYSTEM PARAMETERS Test Circuit Figure 2 (Note 3)
VOUT
Output Voltage
VIN = 8V to 40V, ILOAD = 20 mA to 1A
5.0
4.925/4.850
5.075/5.150
VOUT
Output Voltage
VIN = 6.5V to 40V, ILOAD = 20 mA to 500 mA
5.0
4.925/4.850
5.075/5.150
η
Efficiency
VIN = 12V, ILOAD = 1A
90
V
V
%
LM2672-12
Symbol
Parameter
Conditions
Typical
Min
Max
(Note 4)
(Note 5)
(Note 5)
11.82/11.64
12.18/12.36
Units
SYSTEM PARAMETERS Test Circuit Figure 2 (Note 3)
VOUT
Output Voltage
VIN = 15V to 40V, ILOAD = 20 mA to 1A
12
η
Efficiency
VIN = 24V, ILOAD = 1A
94
V
%
LM2672-ADJ
Symbol
Parameter
Conditions
Typ
Min
Max
(Note 4)
(Note 5)
(Note 5)
1.210
1.192/1.174
1.228/1.246
Units
SYSTEM PARAMETERS Test Circuit Figure 3 (Note 3)
VFB
Feedback
Voltage
VIN = 8V to 40V, ILOAD = 20 mA to 1A
V
VOUT Programmed for 5V
(see Circuit of Figure 3)
3
www.national.com
LM2672
LM2672-ADJ
Symbol
VFB
(Continued)
Parameter
Feedback
Voltage
Conditions
VIN = 6.5V to 40V, ILOAD = 20 mA to 500 mA
Typ
Min
Max
(Note 4)
(Note 5)
(Note 5)
1.210
1.192/1.174
1.228/1.246
Units
V
VOUT Programmed for 5V
(see Circuit of Figure 3)
η
Efficiency
VIN = 12V, ILOAD = 1A
90
%
All Output Voltage Versions
Specifications with standard type face are for TJ = 25˚C, and those in bold type face apply over full Operating Temperature
Range. Unless otherwise specified, VIN = 12V for the 3.3V, 5V, and Adjustable versions and VIN = 24V for the 12V version,
and ILOAD = 100 mA.
Symbol
Parameters
Conditions
Typ
Min
Max
Units
3.6
mA
DEVICE PARAMETERS
IQ
Quiescent Current
VFEEDBACK = 8V
2.5
For 3.3V, 5.0V, and ADJ Versions
VFEEDBACK = 15V
2.5
mA
For 12V Versions
ISTBY
Standby Quiescent Current
ICL
Current Limit
IL
Output Leakage Current
ON/OFF Pin = 0V
50
1.55
VIN = 40V, ON/OFF Pin = 0V
1.25/1.2
1
100/150
µA
2.1/2.2
A
25
µA
VSWITCH = 0V
VSWITCH = −1V, ON/OFF Pin = 0V
6
15
mA
RDS(ON)
Switch On-Resistance
ISWITCH = 1A
0.25
0.30/0.50
Ω
fO
Oscillator Frequency
Measured at Switch Pin
260
275
kHz
D
Maximum Duty Cycle
95
%
Minimum Duty Cycle
0
%
85
nA
IBIAS
Feedback Bias
VFEEDBACK = 1.3V
Current
ADJ Version Only
VS/D
ON/OFF Pin
IS/D
ON/OFF Pin Current
FSYNC
Synchronization Frequency
VSYNC
225
1.4
0.8
2.0
V
ON/OFF Pin = 0V
20
7
37
VSYNC = 3.5V, 50% duty cycle
400
kHz
Synchronization Threshold
Voltage
1.4
V
VSS
Soft-Start Voltage
0.63
0.53
0.73
V
ISS
Soft-Start Current
4.5
1.5
6.9
µA
θJA
Thermal Resistance
Voltage Thesholds
N Package, Junction to Ambient (Note 6)
95
M Package, Junction to Ambient (Note 6)
105
µA
˚C/W
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but device parameter specifications may not be guaranteed under these conditions. For guaranteed specifications and test conditions, see
the Electrical Characteristics.
Note 2: The human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin.
Note 3: External components such as the catch diode, inductor, input and output capacitors, and voltage programming resistors can affect switching regulator
performance. When the LM2672 is used as shown in Figure 2 and Figure 3 test circuits, system performance will be as specified by the system parameters section
of the Electrical Characteristics.
Note 4: Typical numbers are at 25˚C and represent the most likely norm.
Note 5: All limits guaranteed at room temperature (standard type face) and at temperature extremes (bold type face). All room temperature limits are 100%
production tested. All limits at temperature extremes are guaranteed via correlation using standard Statistical Quality Control (SQC) methods. All limits are used
to calculate Average Outgoing Quality Level (AOQL).
Note 6: Junction to ambient thermal resistance with approximately 1 square inch of printed circuit board copper surrounding the leads. Additional copper area will
lower thermal resistance further. See Application Information section in the application note accompanying this datasheet and the thermal model in LM267X Made
Simple version 6.0 software. The value θJ−A for the LLP (LD) package is specifically dependent on PCB trace area, trace material, and the number of layers and
thermal vias. For improved thermal resistance and power dissipation for the LLP package, refer to Application Note AN-1187.
www.national.com
4
LM2672
Typical Performance Characteristics
Normalized
Output Voltage
Line Regulation
01293403
Drain-to-Source
Resistance
Efficiency
Switch Current Limit
ON/OFF Threshold
Voltage
01293409
Switching Frequency
Operating
Quiescent Current
01293407
01293406
Standby
Quiescent Current
01293405
01293404
ON/OFF Pin
Current (Sourcing)
01293410
Feedback Pin
Bias Current
5
01293411
Peak Switch Current
01293413
01293412
01293408
01293414
www.national.com
LM2672
Typical Performance Characteristics
(Continued)
Dropout Voltage — 3.3V Option
Dropout Voltage — 5.0V Option
01293415
01293416
Block Diagram
01293417
* Patent Number 5,514,947
† Patent Number 5,382,918
FIGURE 1.
www.national.com
6
LM2672
Typical Performance
Characteristics (Circuit of Figure 2)
Discontinuous Mode Switching Waveforms
VIN = 20V, VOUT = 5V, ILOAD = 300 mA
L = 15 µH, COUT = 68 µF (2x), COUTESR = 25 mΩ
Continuous Mode Switching Waveforms
VIN = 20V, VOUT = 5V, ILOAD = 1A
L = 47 µH, COUT = 68 µF, COUTESR = 50 mΩ
01293418
01293419
Horizontal Time Base: 1 µs/div
Horizontal Time Base: 1 µs/div
A: VSW Pin Voltage, 10 V/div.
B: Inductor Current, 0.5 A/div
A: VSW Pin Voltage, 10 V/div.
B: Inductor Current, 0.5 A/div
C: Output Ripple Voltage, 20 mV/div AC-Coupled
C: Output Ripple Voltage, 20 mV/div AC-Coupled
Load Transient Response for Discontinuous Mode
VIN = 20V, VOUT = 5V,
L = 47 µH, COUT = 68 µF, COUTESR = 50 mΩ
Load Transient Response for Continuous Mode
VIN = 20V, VOUT = 5V, ILOAD = 1A
L = 47 µH, COUT = 68 µF, COUTESR = 50 mΩ
01293420
01293421
Horizontal Time Base: 50 µs/div
Horizontal Time Base: 200 µs/div
A: Output Voltage, 100 mV/div, AC-Coupled
A: Output Voltage, 100 mV/div, AC-Coupled
B: Load Current: 200 mA to 1A Load Pulse
B: Load Current: 100 mA to 300 mA Load Pulse
7
www.national.com
LM2672
Test Circuit and Layout Guidelines
01293422
CIN - 22 µF, 50V Tantalum, Sprague “199D Series”
COUT - 47 µF, 25V Tantalum, Sprague “595D Series”
D1 - 3.3A, 50V Schottky Rectifier, IR 30WQ05F
L1 - 68 µH Sumida #RCR110D-680L
CB - 0.01 µF, 50V Ceramic
FIGURE 2. Standard Test Circuits and Layout Guides
Fixed Output Voltage Versions
01293423
CIN - 22 µF, 50V Tantalum, Sprague “199D Series”
COUT - 47 µF, 25V Tantalum, Sprague “595D Series”
D1 - 3.3A, 50V Schottky Rectifier, IR 30WQ05F
L1 - 68 µH Sumida #RCR110D-680L
R1 - 1.5 kΩ, 1%
CB - 0.01 µF, 50V Ceramic
For a 5V output, select R2 to be 4.75 kΩ, 1%
where VREF = 1.21V
Use a 1% resistor for best stability.
FIGURE 3. Standard Test Circuits and Layout Guides
Adjustable Output Voltage Versions
www.national.com
8
PROCEDURE (Fixed Output Voltage Version)
EXAMPLE (Fixed Output Voltage Version)
To simplify the buck regulator design procedure, National
Semiconductor is making available computer design software to
be used with the SIMPLE SWITCHER line of switching
regulators. LM267X Made Simple version 6.0 is available on
Windows ® 3.1, NT, or 95 operating systems.
Given:
Given:
VOUT = Regulated Output Voltage (3.3V, 5V, or 12V)
VOUT = 5V
VIN(max) = Maximum DC Input Voltage
VIN(max) = 12V
ILOAD(max) = Maximum Load Current
ILOAD(max) = 1A
1. Inductor Selection (L1)
A. Select the correct inductor value selection guide from Figure
4 and Figure 5 or Figure 6 (output voltages of 3.3V, 5V, or 12V
respectively). For all other voltages, see the design procedure
for the adjustable version.
1. Inductor Selection (L1)
A. Use the inductor selection guide for the 5V version shown in
Figure 5.
B. From the inductor value selection guide, identify the
inductance region intersected by the Maximum Input Voltage
line and the Maximum Load Current line. Each region is
identified by an inductance value and an inductor code (LXX).
B. From the inductor value selection guide shown in Figure 5,
the inductance region intersected by the 12V horizontal line and
the 1A vertical line is 33 µH, and the inductor code is L23.
C. Select an appropriate inductor from the four manufacturer’s
part numbers listed in Figure 8. Each manufacturer makes a
different style of inductor to allow flexibility in meeting various
design requirements. Listed below are some of the
differentiating characteristics of each manufacturer’s inductors:
C. The inductance value required is 33 µH. From the table in
Figure 8, go to the L23 line and choose an inductor part number
from any of the four manufacturers shown. (In most instances,
both through hole and surface mount inductors are available.)
Schott: ferrite EP core inductors; these have very low leakage
magnetic fields to reduce electro-magnetic interference (EMI)
and are the lowest power loss inductors
Renco: ferrite stick core inductors; benefits are typically lowest
cost inductors and can withstand E • T and transient peak
currents above rated value. Be aware that these inductors have
an external magnetic field which may generate more EMI than
other types of inductors.
Pulse: powered iron toroid core inductors; these can also be low
cost and can withstand larger than normal E • T and transient
peak currents. Toroid inductors have low EMI.
Coilcraft: ferrite drum core inductors; these are the smallest
physical size inductors, available only as SMT components. Be
aware that these inductors also generate EMI — but less than
stick inductors.
Complete specifications for these inductors are available from
the respective manufacturers. A table listing the manufacturers’
phone numbers is located in Figure 9.
2. Output Capacitor Selection (COUT)
A. Select an output capacitor from the output capacitor table in
Figure 10. Using the output voltage and the inductance value
found in the inductor selection guide, step 1, locate the
appropriate capacitor value and voltage rating.
2. Output Capacitor Selection (COUT)
A. Use the 5.0V section in the output capacitor table in Figure
10. Choose a capacitor value and voltage rating from the line
that contains the inductance value of 33 µH. The capacitance
and voltage rating values corresponding to the 33 µH
9
www.national.com
LM2672
LM2672 Series Buck Regulator Design Procedure (Fixed Output)
LM2672
LM2672 Series Buck Regulator Design Procedure (Fixed Output)
PROCEDURE (Fixed Output Voltage Version)
(Continued)
EXAMPLE (Fixed Output Voltage Version)
The capacitor list contains through-hole electrolytic capacitors
from four different capacitor manufacturers and surface mount
tantalum capacitors from two different capacitor manufacturers.
It is recommended that both the manufacturers and the
manufacturer’s series that are listed in the table be used. A
table listing the manufacturers’ phone numbers is located in
Figure 11.
Surface Mount:
68 µF/10V Sprague 594D Series.
100 µF/10V AVX TPS Series.
Through Hole:
68 µF/10V Sanyo OS-CON SA Series.
220 µF/35V Sanyo MV-GX Series.
220 µF/35V Nichicon PL Series.
220 µF/35V Panasonic HFQ Series.
3. Catch Diode Selection (D1)
A. In normal operation, the average current of the catch diode is
the load current times the catch diode duty cycle, 1-D (D is the
switch duty cycle, which is approximately the output voltage
divided by the input voltage). The largest value of the catch
diode average current occurs at the maximum load current and
maximum input voltage (minimum D). For normal operation, the
catch diode current rating must be at least 1.3 times greater
than its maximum average current. However, if the power supply
design must withstand a continuous output short, the diode
should have a current rating equal to the maximum current limit
of the LM2672. The most stressful condition for this diode is a
shorted output condition.
3. Catch Diode Selection (D1)
A. Refer to the table shown in Figure 12. In this example, a 1A,
20V Schottky diode will provide the best performance. If the
circuit must withstand a continuous shorted output, a higher
current Schottky diode is recommended.
B. The reverse voltage rating of the diode should be at least
1.25 times the maximum input voltage.
C. Because of their fast switching speed and low forward
voltage drop, Schottky diodes provide the best performance and
efficiency. This Schottky diode must be located close to the
LM2672 using short leads and short printed circuit traces.
www.national.com
10
(Continued)
PROCEDURE (Fixed Output Voltage Version)
EXAMPLE (Fixed Output Voltage Version)
4. Input Capacitor (CIN)
A low ESR aluminum or tantalum bypass capacitor is needed
between the input pin and ground to prevent large voltage
transients from appearing at the input. This capacitor should be
located close to the IC using short leads. In addition, the RMS
current rating of the input capacitor should be selected to be at
least 1⁄2 the DC load current. The capacitor manufacturer data
sheet must be checked to assure that this current rating is not
exceeded. The curves shown in Figure 14 show typical RMS
current ratings for several different aluminum electrolytic
capacitor values. A parallel connection of two or more
capacitors may be required to increase the total minimum RMS
current rating to suit the application requirements.
For an aluminum electrolytic capacitor, the voltage rating should
be at least 1.25 times the maximum input voltage. Caution must
be exercised if solid tantalum capacitors are used. The tantalum
capacitor voltage rating should be twice the maximum input
voltage. The tables in Figure 15 show the recommended
application voltage for AVX TPS and Sprague 594D tantalum
capacitors. It is also recommended that they be surge current
tested by the manufacturer. The TPS series available from AVX,
and the 593D and 594D series from Sprague are all surge
current tested. Another approach to minimize the surge current
stresses on the input capacitor is to add a small inductor in
series with the input supply line.
Use caution when using ceramic capacitors for input bypassing,
because it may cause severe ringing at the VIN pin.
4. Input Capacitor (CIN)
The important parameters for the input capacitor are the input
voltage rating and the RMS current rating. With a maximum
input voltage of 12V, an aluminum electrolytic capacitor with a
voltage rating greater than 15V (1.25 x VIN) would be needed.
The next higher capacitor voltage rating is 16V.
The RMS current rating requirement for the input capacitor in a
buck regulator is approximately 1⁄2 the DC load current. In this
example, with a 1A load, a capacitor with a RMS current rating
of at least 500 mA is needed. The curves shown in Figure 14
can be used to select an appropriate input capacitor. From the
curves, locate the 16V line and note which capacitor values
have RMS current ratings greater than 500 mA.
For a through hole design, a 330 µF/16V electrolytic capacitor
(Panasonic HFQ series, Nichicon PL, Sanyo MV-GX series or
equivalent) would be adequate. Other types or other
manufacturers’ capacitors can be used provided the RMS ripple
current ratings are adequate. Additionally, for a complete
surface mount design, electrolytic capacitors such as the Sanyo
CV-C or CV-BS and the Nichicon WF or UR and the NIC
Components NACZ series could be considered.
For surface mount designs, solid tantalum capacitors can be
used, but caution must be exercised with regard to the capacitor
surge current rating and voltage rating. In this example,
checking Figure 15, and the Sprague 594D series datasheet, a
Sprague 594D 15 µF, 25V capacitor is adequate.
5. Boost Capacitor (CB)
5. Boost Capacitor (CB)
This capacitor develops the necessary voltage to turn the switch For this application, and all applications, use a 0.01 µF, 50V
gate on fully. All applications should use a 0.01 µF, 50V ceramic ceramic capacitor.
capacitor.
6. Soft-Start Capacitor (CSS - optional)
This capacitor controls the rate at which the device starts up.
The formula for the soft-start capacitor CSS is:
6. Soft-Start Capacitor (CSS - optional)
For this application, selecting a start-up time of 10 ms and using
the formula for CSS results in a value of:
where:
ISS = Soft-Start Current :4.5 µA typical.
tSS = Soft-Start Time :Selected.
VSSTH = Soft-Start Threshold Voltage :0.63V typical.
VOUT = Output Voltage :Selected.
VSCHOTTKY = Schottky Diode Voltage Drop :0.4V typical.
VIN = Input Voltage :Selected.
If this feature is not desired, leave this pin open.
11
www.national.com
LM2672
LM2672 Series Buck Regulator Design Procedure (Fixed Output)
LM2672
LM2672 Series Buck Regulator Design Procedure (Fixed Output)
PROCEDURE (Fixed Output Voltage Version)
(Continued)
EXAMPLE (Fixed Output Voltage Version)
7. Frequency Synchronization (optional)
7. Frequency Synchronization (optional)
The LM2672 (oscillator) can be synchronized to run with an
For all applications, use a 1 kΩ resistor and a 100 pF capacitor
external oscillator, using the sync pin (pin 3). By doing so, the
for the RC filter.
LM2672 can be operated at higher frequencies than the
standard frequency of 260 kHz. This allows for a reduction in
the size of the inductor and output capacitor.
As shown in the drawing below, a signal applied to a RC filter at
the sync pin causes the device to synchronize to the frequency
of that signal. For a signal with a peak-to-peak amplitude of 3V
or greater, a 1 kΩ resistor and a 100 pF capacitor are suitable
values.
www.national.com
12
LM2672
INDUCTOR VALUE SELECTION GUIDES
(For Continuous Mode Operation)
01293429
01293431
FIGURE 4. LM2672-3.3
FIGURE 6. LM2672-12
01293430
01293432
FIGURE 5. LM2672-5.0
FIGURE 7. LM2672-ADJ
13
www.national.com
LM2672
Ind.
Inductance Current
Ref.
(µH)
(A)
Desg.
Schott
Renco
Pulse Engineering
Coilcraft
Through
Surface
Through
Surface
Through
Surface
Surface
Hole
Mount
Hole
Mount
Hole
Mount
Mount
L4
68
0.32
67143940 67144310
RL-1284-68-43
RL1500-68
PE-53804 PE-53804-S DO1608-683
L5
47
0.37
67148310 67148420
RL-1284-47-43
RL1500-47
PE-53805 PE-53805-S DO1608-473
L6
33
0.44
67148320 67148430
RL-1284-33-43
RL1500-33
PE-53806 PE-53806-S DO1608-333
L7
22
0.52
67148330 67148440
RL-1284-22-43
RL1500-22
PE-53807 PE-53807-S DO1608-223
L9
220
0.32
67143960 67144330
RL-5470-3
RL1500-220 PE-53809 PE-53809-S DO3308-224
L10
150
0.39
67143970 67144340
RL-5470-4
RL1500-150 PE-53810 PE-53810-S DO3308-154
L11
100
0.48
67143980 67144350
RL-5470-5
RL1500-100 PE-53811 PE-53811-S DO3308-104
L12
68
0.58
67143990 67144360
RL-5470-6
RL1500-68
L13
47
0.70
67144000 67144380
RL-5470-7
RL1500-47
PE-53813 PE-53813-S DO3308-473
L14
33
0.83
67148340 67148450
RL-1284-33-43
RL1500-33
PE-53814 PE-53814-S DO3308-333
L15
22
0.99
67148350 67148460
RL-1284-22-43
RL1500-22
PE-53815 PE-53815-S DO3308-223
L18
220
0.55
67144040 67144420
RL-5471-2
RL1500-220 PE-53818 PE-53818-S DO3316-224
L19
150
0.66
67144050 67144430
RL-5471-3
RL1500-150 PE-53819 PE-53819-S DO3316-154
L20
100
0.82
67144060 67144440
RL-5471-4
RL1500-100 PE-53820 PE-53820-S DO3316-104
L21
68
0.99
67144070 67144450
RL-5471-5
RL1500-68
PE-53821 PE-53821-S DO3316-683
L22
47
1.17
67144080 67144460
RL-5471-6
—
PE-53822 PE-53822-S DO3316-473
L23
33
1.40
67144090 67144470
RL-5471-7
—
PE-53823 PE-53823-S DO3316-333
L24
22
1.70
67148370 67148480
RL-1283-22-43
—
PE-53824 PE-53824-S DO3316-223
L27
220
1.00
67144110 67144490
RL-5471-2
—
PE-53827 PE-53827-S DO5022P-224
L28
150
1.20
67144120 67144500
RL-5471-3
—
PE-53828 PE-53828-S DO5022P-154
L29
100
1.47
67144130 67144510
RL-5471-4
—
PE-53829 PE-53829-S DO5022P-104
L30
68
1.78
67144140 67144520
RL-5471-5
—
PE-53830 PE-53830-S DO5022P-683
PE-53812 PE-53812-S DO3308-683
FIGURE 8. Inductor Manufacturers’ Part Numbers
Coilcraft Inc.
Coilcraft Inc., Europe
Pulse Engineering Inc.
Phone
(800) 322-2645
FAX
(708) 639-1469
Phone
+44 1236 730 595
FAX
+44 1236 730 627
Phone
(619) 674-8100
FAX
(619) 674-8262
Pulse Engineering Inc.,
Phone
+353 93 24 107
Europe
FAX
+353 93 24 459
Renco Electronics Inc.
Phone
(800) 645-5828
Schott Corp.
FAX
(516) 586-5562
Phone
(612) 475-1173
FAX
(612) 475-1786
FIGURE 9. Inductor Manufacturers’ Phone Numbers
www.national.com
14
LM2672
Output Capacitor
Output
Voltage
(V)
3.3
5.0
12
Inductance
(µH)
Surface Mount
Through Hole
Sprague
AVX TPS
Sanyo OS-CON
Sanyo MV-GX
Nichicon
Panasonic
594D Series
Series
SA Series
Series
PL Series
HFQ Series
(µF/V)
(µF/V)
(µF/V)
(µF/V)
(µF/V)
(µF/V)
22
120/6.3
100/10
100/10
330/35
330/35
330/35
33
120/6.3
100/10
68/10
220/35
220/35
220/35
47
68/10
100/10
68/10
150/35
150/35
150/35
68
120/6.3
100/10
100/10
120/35
120/35
120/35
100
120/6.3
100/10
100/10
120/35
120/35
120/35
150
120/6.3
100/10
100/10
120/35
120/35
120/35
22
100/16
100/10
100/10
330/35
330/35
330/35
33
68/10
10010
68/10
220/35
220/35
220/35
47
68/10
100/10
68/10
150/35
150/35
150/35
68
100/16
100/10
100/10
120/35
120/35
120/35
100
100/16
100/10
100/10
120/35
120/35
120/35
150
100/16
100/10
100/10
120/35
120/35
120/35
22
120/20
(2x) 68/20
68/20
330/35
330/35
330/35
33
68/25
68/20
68/20
220/35
220/35
220/35
47
47/20
68/20
47/20
150/35
150/35
150/35
68
47/20
68/20
47/20
120/35
120/35
120/35
100
47/20
68/20
47/20
120/35
120/35
120/35
150
47/20
68/20
47/20
120/35
120/35
120/35
220
47/20
68/20
47/20
120/35
120/35
120/35
FIGURE 10. Output Capacitor Table
Nichicon Corp.
Panasonic
AVX Corp.
Sprague/Vishay
Sanyo Corp.
Phone
(847) 843-7500
FAX
(847) 843-2798
Phone
(714) 373-7857
FAX
(714) 373-7102
Phone
(803) 448-9411
FAX
(803) 448-1943
Phone
(207) 324-4140
FAX
(207) 324-7223
Phone
(619) 661-6322
FAX
(619) 661-1055
FIGURE 11. Capacitor Manufacturers’ Phone Numbers
15
www.national.com
LM2672
1A Diodes
VR
20V
30V
40V
3A Diodes
Surface
Through
Surface
Through
Mount
Hole
Mount
Hole
SK12
1N5817
SK32
1N5820
B120
SR102
SK13
1N5818
SK33
1N5821
30WQ03F
31DQ03
SK34
1N5822
SR302
B130
11DQ03
MBRS130
SR103
SK14
1N5819
B140
11DQ04
30BQ040
MBR340
MBRS140
SR104
30WQ04F
31DQ04
10BQ040
MBRS340
SR304
10MQ040
MBRD340
15MQ040
50V
SK15
MBR150
SK35
MBR350
B150
11DQ05
30WQ05F
31DQ05
10BQ050
SR105
SR305
FIGURE 12. Schottky Diode Selection Table
International Rectifier
Corp.
Motorola, Inc.
General Instruments
Corp.
Diodes, Inc.
Phone
(310) 322-3331
FAX
(310) 322-3332
Phone
(800) 521-6274
FAX
(602) 244-6609
Phone
(516) 847-3000
FAX
(516) 847-3236
Phone
(805) 446-4800
FAX
(805) 446-4850
FIGURE 13. Diode Manufacturers’ Phone Numbers
01293433
FIGURE 14. RMS Current Ratings for Low ESR Electrolytic Capacitors (Typical)
www.national.com
16
LM2672
AVX TPS
Recommended
Application Voltage
Voltage
Rating
+85˚C Rating
3.3
6.3
5
10
10
20
12
25
15
35
Sprague 594D
Recommended
Application Voltage
Voltage
Rating
+85˚C Rating
2.5
4
3.3
6.3
5
10
8
16
12
20
18
25
24
35
29
50
FIGURE 15. Recommended Application Voltage for AVX TPS and
Sprague 594D Tantalum Chip Capacitors Derated for 85˚C.
LM2672 Series Buck Regulator
Design Procedure (Adjustable
Output)
PROCEDURE (Adjustable Output Voltage Version)
EXAMPLE (Adjustable Output Voltage Version)
To simplify the buck regulator design procedure, National
Semiconductor is making available computer design software to
be used with the SIMPLE SWITCHER line of switching
regulators. LM267X Made Simple version 6.0 is available on
Windows 3.1, NT, or 95 operating systems.
Given:
Given:
VOUT = Regulated Output Voltage
VOUT = 20V
VIN(max) = Maximum Input Voltage
VIN(max) = 28V
ILOAD(max) = Maximum Load Current
ILOAD(max) = 1A
F = Switching Frequency (Fixed at a nominal 260 kHz).
F = Switching Frequency (Fixed at a nominal 260 kHz).
1. Programming Output Voltage (Selecting R1 and R2, as
shown in Figure 3)
Use the following formula to select the appropriate resistor
values.
1. Programming Output Voltage (Selecting R1 and R2, as
shown in Figure 3)
Select R1 to be 1 kΩ, 1%. Solve for R2.
where VREF = 1.21V
Select a value for R1 between 240Ω and 1.5 kΩ. The lower
R2 = 1 kΩ (16.53 − 1) = 15.53 kΩ, closest 1% value is 15.4 kΩ.
resistor values minimize noise pickup in the sensitive feedback R2 = 15.4 kΩ.
pin. (For the lowest temperature coefficient and the best stability
with time, use 1% metal film resistors.)
17
www.national.com
LM2672
LM2672 Series Buck Regulator Design Procedure (Adjustable Output)
(Continued)
PROCEDURE (Adjustable Output Voltage Version)
2. Inductor Selection (L1)
A. Calculate the inductor Volt • microsecond constant E • T
(V • µs), from the following formula:
EXAMPLE (Adjustable Output Voltage Version)
2. Inductor Selection (L1)
A. Calculate the inductor Volt • microsecond constant (E • T),
where VSAT =internal switch saturation voltage=0.25V and
VD = diode forward voltage drop = 0.5V
B. Use the E • T value from the previous formula and match it
with the E • T number on the vertical axis of the Inductor Value
Selection Guide shown in Figure 7.
B. E • T = 21.6 (V • µs)
C. On the horizontal axis, select the maximum load current.
C. ILOAD(max) = 1A
D. Identify the inductance region intersected by the E • T value
and the Maximum Load Current value. Each region is identified
by an inductance value and an inductor code (LXX).
D. From the inductor value selection guide shown in Figure 7,
the inductance region intersected by the 21.6 (V • µs) horizontal
line and the 1A vertical line is 68 µH, and the inductor code is
L30.
E. Select an appropriate inductor from the four manufacturer’s
part numbers listed in Figure 8. For information on the different
types of inductors, see the inductor selection in the fixed output
voltage design procedure.
E. From the table in Figure 8, locate line L30, and select an
inductor part number from the list of manufacturers’ part
numbers.
3. Output Capacitor SeIection (COUT)
A. Select an output capacitor from the capacitor code selection
guide in Figure 16. Using the inductance value found in the
inductor selection guide, step 1, locate the appropriate capacitor
code corresponding to the desired output voltage.
3. Output Capacitor SeIection (COUT)
A. Use the appropriate row of the capacitor code selection
guide, in Figure 16. For this example, use the 15–20V row. The
capacitor code corresponding to an inductance of 68 µH is C20.
B. Select an appropriate capacitor value and voltage rating,
using the capacitor code, from the output capacitor selection
table in Figure 17. There are two solid tantalum (surface mount)
capacitor manufacturers and four electrolytic (through hole)
capacitor manufacturers to choose from. It is recommended that
both the manufacturers and the manufacturer’s series that are
listed in the table be used. A table listing the manufacturers’
phone numbers is located in Figure 11.
B. From the output capacitor selection table in Figure 17,
choose a capacitor value (and voltage rating) that intersects the
capacitor code(s) selected in section A, C20.
The capacitance and voltage rating values corresponding to the
capacitor code C20 are the:
Surface Mount:
33 µF/25V Sprague 594D Series.
33 µF/25V AVX TPS Series.
Through Hole:
33 µF/25V Sanyo OS-CON SC Series.
120 µF/35V Sanyo MV-GX Series.
120 µF/35V Nichicon PL Series.
120 µF/35V Panasonic HFQ Series.
Other manufacturers or other types of capacitors may also be
used, provided the capacitor specifications (especially the 100
kHz ESR) closely match the characteristics of the capacitors
listed in the output capacitor table. Refer to the capacitor
manufacturers’ data sheet for this information.
www.national.com
18
(Continued)
PROCEDURE (Adjustable Output Voltage Version)
EXAMPLE (Adjustable Output Voltage Version)
4. Catch Diode Selection (D1)
A. In normal operation, the average current of the catch diode is
the load current times the catch diode duty cycle, 1-D (D is the
switch duty cycle, which is approximately VOUT/VIN). The largest
value of the catch diode average current occurs at the maximum
input voltage (minimum D). For normal operation, the catch
diode current rating must be at least 1.3 times greater than its
maximum average current. However, if the power supply design
must withstand a continuous output short, the diode should have
a current rating greater than the maximum current limit of the
LM2672. The most stressful condition for this diode is a shorted
output condition.
4. Catch Diode Selection (D1)
A. Refer to the table shown in Figure 12. Schottky diodes
provide the best performance, and in this example a 1A, 40V
Schottky diode would be a good choice. If the circuit must
withstand a continuous shorted output, a higher current (at least
2.2A) Schottky diode is recommended.
B. The reverse voltage rating of the diode should be at least
1.25 times the maximum input voltage.
C. Because of their fast switching speed and low forward
voltage drop, Schottky diodes provide the best performance and
efficiency. The Schottky diode must be located close to the
LM2672 using short leads and short printed circuit traces.
5. Input Capacitor (CIN)
A low ESR aluminum or tantalum bypass capacitor is needed
between the input pin and ground to prevent large voltage
transients from appearing at the input. This capacitor should be
located close to the IC using short leads. In addition, the RMS
current rating of the input capacitor should be selected to be at
least 1⁄2 the DC load current. The capacitor manufacturer data
sheet must be checked to assure that this current rating is not
exceeded. The curves shown in Figure 14 show typical RMS
current ratings for several different aluminum electrolytic
capacitor values. A parallel connection of two or more
capacitors may be required to increase the total minimum RMS
current rating to suit the application requirements.
For an aluminum electrolytic capacitor, the voltage rating should
be at least 1.25 times the maximum input voltage. Caution must
be exercised if solid tantalum capacitors are used. The tantalum
capacitor voltage rating should be twice the maximum input
voltage. The tables in Figure 15 show the recommended
application voltage for AVX TPS and Sprague 594D tantalum
capacitors. It is also recommended that they be surge current
tested by the manufacturer. The TPS series available from AVX,
and the 593D and 594D series from Sprague are all surge
current tested. Another approach to minimize the surge current
stresses on the input capacitor is to add a small inductor in
series with the input supply line.
Use caution when using ceramic capacitors for input bypassing,
because it may cause severe ringing at the VIN pin.
5. Input Capacitor (CIN)
The important parameters for the input capacitor are the input
voltage rating and the RMS current rating. With a maximum
input voltage of 28V, an aluminum electrolytic capacitor with a
voltage rating of at least 35V (1.25 x VIN) would be needed.
The RMS current rating requirement for the input capacitor in a
buck regulator is approximately 1⁄2 the DC load current. In this
example, with a 1A load, a capacitor with a RMS current rating
of at least 500 mA is needed. The curves shown in Figure 14
can be used to select an appropriate input capacitor. From the
curves, locate the 35V line and note which capacitor values
have RMS current ratings greater than 500 mA.
For a through hole design, a 330 µF/35V electrolytic capacitor
(Panasonic HFQ series, Nichicon PL, Sanyo MV-GX series or
equivalent) would be adequate. Other types or other
manufacturers’ capacitors can be used provided the RMS ripple
current ratings are adequate. Additionally, for a complete
surface mount design, electrolytic capacitors such as the Sanyo
CV-C or CV-BS and the Nichicon WF or UR and the NIC
Components NACZ series could be considered.
For surface mount designs, solid tantalum capacitors can be
used, but caution must be exercised with regard to the capacitor
surge current rating and voltage rating. In this example,
checking Figure 15, and the Sprague 594D series datasheet, a
Sprague 594D 15 µF, 50V capacitor is adequate.
6. Boost Capacitor (CB)
6. Boost Capacitor (CB)
This capacitor develops the necessary voltage to turn the switch For this application, and all applications, use a 0.01 µF, 50V
gate on fully. All applications should use a 0.01 µF, 50V ceramic ceramic capacitor.
capacitor.
If the soft-start and frequency synchronization features are
desired, look at steps 6 and 7 in the fixed output design
procedure.
19
www.national.com
LM2672
LM2672 Series Buck Regulator Design Procedure (Adjustable Output)
LM2672
LM2672 Series Buck Regulator Design Procedure (Adjustable Output)
(Continued)
Inductance (µH)
Case
Style (Note 7)
Output
Voltage (V)
22
33
47
68
100
150
220
SM and TH
1.21–2.50
—
—
—
—
C1
C2
C3
SM and TH
2.50–3.75
—
—
—
C1
C2
C3
C3
SM and TH
3.75–5.0
—
—
C4
C5
C6
C6
C6
SM and TH
5.0–6.25
—
C4
C7
C6
C6
C6
C6
SM and TH
6.25–7.5
C8
C4
C7
C6
C6
C6
C6
SM and TH
7.5–10.0
C9
C10
C11
C12
C13
C13
C13
SM and TH
10.0–12.5
C14
C11
C12
C12
C13
C13
C13
SM and TH
12.5–15.0
C15
C16
C17
C17
C17
C17
C17
SM and TH
15.0–20.0
C18
C19
C20
C20
C20
C20
C20
SM and TH
20.0–30.0
C21
C22
C22
C22
C22
C22
C22
TH
30.0–37.0
C23
C24
C24
C25
C25
C25
C25
Note 7: SM - Surface Mount, TH - Through Hole
FIGURE 16. Capacitor Code Selection Guide
Output Capacitor
Cap.
Ref.
Desg.
#
Surface Mount
Through Hole
Sprague
AVX TPS
Sanyo OS-CON
Sanyo MV-GX
Nichicon
Panasonic
594D Series
Series
SA Series
Series
PL Series
HFQ Series
(µF/V)
(µF/V)
(µF/V)
(µF/V)
(µF/V)
(µF/V)
C1
120/6.3
100/10
100/10
220/35
220/35
220/35
C2
120/6.3
100/10
100/10
150/35
150/35
150/35
C3
120/6.3
100/10
100/35
120/35
120/35
120/35
C4
68/10
100/10
68/10
220/35
220/35
220/35
C5
100/16
100/10
100/10
150/35
150/35
150/35
C6
100/16
100/10
100/10
120/35
120/35
120/35
C7
68/10
100/10
68/10
150/35
150/35
150/35
C8
100/16
100/10
100/10
330/35
330/35
330/35
C9
100/16
100/16
100/16
330/35
330/35
330/35
C10
100/16
100/16
68/16
220/35
220/35
220/35
C11
100/16
100/16
68/16
150/35
150/35
150/35
C12
100/16
100/16
68/16
120/35
120/35
120/35
C13
100/16
100/16
100/16
120/35
120/35
120/35
C14
100/16
100/16
100/16
220/35
220/35
220/35
C15
47/20
68/20
47/20
220/35
220/35
220/35
C16
47/20
68/20
47/20
150/35
150/35
150/35
C17
47/20
68/20
47/20
120/35
120/35
120/35
C18
68/25
(2x) 33/25
47/25 (Note 8)
220/35
220/35
220/35
C19
33/25
33/25
33/25 (Note 8)
150/35
150/35
150/35
C20
33/25
33/25
33/25 (Note 8)
120/35
120/35
120/35
C21
33/35
(2x) 22/25
(Note 9)
150/35
150/35
150/35
C22
33/35
22/35
(Note 9)
120/35
120/35
120/35
C23
(Note 9)
(Note 9)
(Note 9)
220/50
100/50
120/50
C24
(Note 9)
(Note 9)
(Note 9)
150/50
100/50
120/50
C25
(Note 9)
(Note 9)
(Note 9)
150/50
82/50
82/50
Note 8: The SC series of Os-Con capacitors (others are SA series)
Note 9: The voltage ratings of the surface mount tantalum chip and Os-Con capacitors are too low to work at these voltages.
FIGURE 17. Output Capacitor Selection Table
www.national.com
20
LM2672
Application Information
TYPICAL SURFACE MOUNT PC BOARD LAYOUT, FIXD OUTPUT (4X SIZE)
01293439
CIN - 15 µF, 50V, Solid Tantalum Sprague, “594D series”
COUT - 68 µF, 16V, Solid Tantalum Sprague, “594D series”
D1 - 1A, 40V Schottky Rectifier, Surface Mount
L1 - 33 µH, L23, Coilcraft DO3316
CB - 0.01 µF, 50V, Ceramic
TYPICAL SURFACE MOUNT PC BOARD LAYOUT, ADJUSTABLE OUTPUT (4X SIZE)
01293440
CIN - 15 µF, 50V, Solid Tantalum Sprague, “594D series”
COUT - 33 µF, 25V, Solid Tantalum Sprague, “594D series”
D1 - 1A, 40V Schottky Rectifier, Surface Mount
L1 - 68 µH, L30, Coilcraft DO3316
CB - 0.01 µF, 50V, Ceramic
R1 - 1k, 1%
R2 - Use formula in Design Procedure
FIGURE 18. PC Board Layout
Layout is very important in switching regulator designs. Rapidly switching currents associated with wiring inductance can
generate voltage transients which can cause problems. For
minimal inductance and ground loops, the wires indicated by
heavy lines (in Figure 2 and Figure 3) should be wide
printed circuit traces and should be kept as short as
possible. For best results, external components should be
located as close to the switcher IC as possible using ground
plane construction or single point grounding.
If open core inductors are used, special care must be
taken as to the location and positioning of this type of inductor. Allowing the inductor flux to intersect sensitive feedback,
IC ground path, and COUT wiring can cause problems.
When using the adjustable version, special care must be
taken as to the location of the feedback resistors and the
associated wiring. Physically locate both resistors near the
IC, and route the wiring away from the inductor, especially an
open core type of inductor.
21
www.national.com
LM2672
Application Information
well as mounting and soldering specifications, refer to Application Note AN-1187.
(Continued)
LLP Package Devices
The LM2672 is offered in the 16 lead LLP surface mount
package to allow for increased power dissipation compared
to the SO-8 and DIP. For details on thermal performance as
www.national.com
22
LM2672
Physical Dimensions
inches (millimeters)
unless otherwise noted
8-Lead (0.150" Wide) Molded Small Outline Package, JEDEC
Order Number LM2672M-3.3, LM2672M-5.0,
LM2672M-12 or LM2672M-ADJ
NS Package Number M08A
23
www.national.com
LM2672
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
8-Lead (0.300" Wide) Molded Dual-In-Line Package
Order Number LM2672N-3.3, LM2672N-5.0,
LM2672N-12 or LM2672N-ADJ
NS Package Number N08E
www.national.com
24
inches (millimeters) unless otherwise noted (Continued)
16-Lead LLP Surface Mount Package
NS Package Number LDA16A
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: [email protected]
www.national.com
National Semiconductor
Europe
Fax: +49 (0) 180-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: [email protected]
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
LM2672 SIMPLE SWITCHER Power Converter High Efficiency 1A Step-Down Voltage Regulator
with Features
Physical Dimensions
Similar pages