LM112,LM212,LM312 LM112 LM212 LM312 Operational Amplifiers Literature Number: SNOSBR9A LM112/LM212/LM312 Operational Amplifiers General Description Connection Diagram Features Y Y Y Y Maximum input bias current of 3 nA over temperature Offset current less than 400 pA over temperature Low noise Guaranteed drift specifications et The LM112 series are the first IC amplifiers to improve reliability by including overvoltage protection for the MOS compensation capacitor. Without this feature, IC’s have been known to suffer catastrophic failure caused by short-duration overvoltage spikes on the supplies. Unlike other internally-compensated IC amplifiers, it is possible to overcompensate with an external capacitor to increase stability margin. The LM212 is identical to the LM112, except that the LM212 has its performance guaranteed over a b25§ C to a 85§ C temperature range instead of b55§ C to a 125§ C. The LM312 is guaranteed over a 0§ C to a 70§ C temperature range. e The LM112 series are micropower operational amplifiers with very low offset-voltage and input-current errorsÐat least a factor of ten better than FET amplifiers over a b 55§ C to a 125§ C temperature range. Similar to the LM108 series, that also use supergain transistors, they differ in that they include internal frequency compensation and have provisions for offset adjustment with a single potentiometer. These amplifiers will operate on supply voltages of g 2V to g 20V, drawing a quiescent current of only 300 mA. Performance is not appreciably affected over this range of voltages, so operation from unregulated power sources is easily accomplished. They can also be run from a single supply like the 5V used for digital circuits. bs ol Metal Can Package TL/H/7751 – 4 Top View Order Number LM112H, LM212H, LM312H or LM112H/883 See NS Package Number H08C Auxiliary Circuits Overcompensation for Greater Stability Margin O Offset Balancing TL/H/7751 – 2 C1995 National Semiconductor Corporation TL/H/7751 TL/H/7751 – 3 RRD-B30M115/Printed in U. S. A. LM112/LM212/LM312 Operational Amplifiers September 1992 Absolute Maximum Ratings Electrical Characteristics (Note 4) Parameter LM112/LM212 Conditions Min Input Offset Current TA e 25§ C Input Bias Current TA e 25§ C Input Resistance TA e 25§ C Supply Current TA e 25§ C Large Signal Voltage Gain TA e 25§ C, VS e g 15V VOUT e g 10V, RL t 10 kX 0.7 Min 2.0 30 Max 2.0 7.5 0.2 0.2 1 0.8 2.0 1.5 7 70 0.3 50 10 0.6 300 40 0.3 25 3.0 Input Offset Current 15 6.0 0.4 Average Temperature Coefficient of Input Offset Current 0.5 2.5 0.15 0.4 Input Bias Current 2.0 3.0 TA e 125§ C O VS e g 15V, VOUT e g 10V RL t 10 kX Output Voltage Swing VS e g 15V, RL e 10 kX Input Voltage Range VS e g 15V mV 25 g 13 g 14 g 13 0.8 nA mA V/mV 10 mV 30 mV/§ C 1.5 nA 10 pA/§ C 10 nA mA 15 g 13.5 nA MX 300 3.0 Average Temperature Coefficient of Input Offset Voltage Large Signal Voltage Gain Units Typ 0.05 Input Offset Voltage Supply Current LM312 Max et TA e 25§ C Typ bs ol Input Offset Voltage e If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/Distributors for availability and specifications. (Note 5) LM112/LM212 LM312 g 20V g 18V Supply Voltage Power Dissipation (Note 1) 500 mW 500 mW g 10 mA g 10 mA Differential Input Current (Note 2) g 15V g 15V Input Voltage (Note 3) Output Short-Circuit Duration Continuous Continuous Operating Temperature Range b 55§ C to a 125§ C LM112 0§ C to a 70§ C b 25§ C to a 85§ C LM212 b 65§ C to a 150§ C b 65§ C to a 150§ C Storage Temperature Range 300§ C Lead Temperature (Soldering, 10 sec.) 300§ C ESD rating to be determined. V/mV g 14 g 14 V V Common-Mode Rejection Ratio 85 100 80 100 dB Supply Voltage Rejection Ratio 80 96 80 96 dB Note 1: The maximum junction temperature of the LM112 is 150§ C, LM212 is 100§ C and LM312 is 85§ C. For operating at elevated temperatures, devices in the H08 package must be derated based on a thermal resistance of 160§ C/W, junction to ambient, or 20§ C/W, junction to case. Note 2: The inputs are shunted with shunt diodes for overvoltage protection. Therefore, excessive current will flow if a differential input voltage in excess of 1V is applied between the inputs unless some limiting resistance is used. Note 3: For supply voltages less than g 15V, the absolute maximum input voltage is equal to the supply voltage. Note 4: These specifications apply for g 5V s VS s g 20V and b 55§ C s TA s a 125§ C (LM112), b 25§ C s TA s a 85§ C (LM212), g 5V s VS s g 15V and 0§ C s TA s a 70§ C (LM312) unless otherwise noted. Note 5: Refer to RETS112X for LM112H military specifications. 2 Typical Performance Characteristics LM112/LM212 Offset Error Drift Error Input Noise Voltage Power Supply Rejection Closed Loop Output Impedance bs ol et e Input Currents Output Swing Supply Current Open Loop Frequency Response Large Signal Frequency Response Voltage Follower Pulse Response O Voltage Gain TL/H/7751 – 5 3 Typical Performance Characteristics LM312 Offset Error Drift Error Input Noise Voltage Power Supply Rejection Closed Loop Output Impedance bs ol et e Input Currents Output Swing Supply Current Open Loop Frequency Response Large Signal Frequency Response Voltage Follower Pulse Response O Voltage Gain TL/H/7751 – 6 4 e et bs ol O TL/H/7751 – 1 Schematic Diagram 5 e et Metal Can Package (H) Order Number LM112H, LM212H, LM312H or LM112H/883 NS Package Number H08C bs ol LM112/LM212/LM312 Operational Amplifiers Physical Dimensions inches (millimeters) LIFE SUPPORT POLICY O NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation 1111 West Bardin Road Arlington, TX 76017 Tel: 1(800) 272-9959 Fax: 1(800) 737-7018 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Europe Fax: (a49) 0-180-530 85 86 Email: cnjwge @ tevm2.nsc.com Deutsch Tel: (a49) 0-180-530 85 85 English Tel: (a49) 0-180-532 78 32 Fran3ais Tel: (a49) 0-180-532 93 58 Italiano Tel: (a49) 0-180-534 16 80 National Semiconductor Hong Kong Ltd. 13th Floor, Straight Block, Ocean Centre, 5 Canton Rd. Tsimshatsui, Kowloon Hong Kong Tel: (852) 2737-1600 Fax: (852) 2736-9960 National Semiconductor Japan Ltd. Tel: 81-043-299-2309 Fax: 81-043-299-2408 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated