Series AM1S-NZ 1 Watt | DC-DC Converter FEATURES: • • • • • • • RoHS compliant 4 Pin SIP Package Low ripple and noise High efficiency up to 81% Operating temperature -40oC to + 85oC Input / Output isolation 1000 and 3000VDC Pin compatible with multiple manufacturers Models Single output Model Output Voltage (V) Input Voltage (V) AM1S-0505S-NZ AM1S-0509S-NZ AM1S-0512S-NZ AM1S-0515S-NZ AM1S-1205S-NZ AM1S-1209S-NZ AM1S-1212S-NZ AM1S-1215S-NZ AM1S-2405S-NZ AM1S-2409S-NZ AM1S-2412S-NZ AM1S-2415S-NZ AM1S-0505SH30-NZ Output Current max (mA) Isolation (VDC) Efficiency (%) 4.5-5.5 4.5-5.5 4.5-5.5 4.5-5.5 10.8-13.2 10.8-13.2 10.8-13.2 10.8-13.2 21.6-26.4 21.6-26.4 21.6-26.4 21.6-26.4 5 9 12 15 5 9 12 15 5 9 12 15 200 110 83 67 200 110 83 67 200 110 83 67 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 78 79 80 78 78 80 81 79 79 80 81 79 4.5-5.5 5 200 3000 70 Input Specifications Parameters Voltage range Nominal Typical 5 12 24 4.5-5.5 10.8-13.2 21.6-26.4 Filter Maximum Units VDC Capacitor Isolation Specifications Parameters Tested I/O voltage Resistance Capacitance Conditions Typical 60 sec Rated Units 1000 or 3000 VDC MOhm pF Maximum Units > 1000 60 Output Specifications Parameters Voltage accuracy Short Circuit protection Line voltage regulation (Single) Load voltage regulation (Single) Temperature coefficient Ripple & Noise Conditions Typical See tolerance graph Momentary (1 sec) ±1.2 10 ±0.03 75 For 1.0% of Vin Load 10 – 100% At 20MHz Bandwidth % % %/oC mV p-p General Specifications Parameters Switching frequency Operating temperature Storage temperature Max Case temperature Cooling www.aimtec.com F 051e R11.I Conditions Typical 100% load Without derating 150 Maximum Units 90 KHz o C o C o C -40 to +85 -55 to +125 Free air convection Tel: +1 514 620 2722 1 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM1S-NZ 1 Watt | DC-DC Converter General Specifications (continued) Parameters Conditions Typical Maximum Units % Humidity 90 Case material Plastic UL94-VO Weight 1.8 g Dimensions (L x W x H) 0.46 x 0.24 x 0.37 inches 11.70 x 6.00 x 9.50 mm MTBF >1 000 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25oC) NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Safety Specifications Parameters Standards Agency approvals IEC60950-1 :2001 UL and CE for 1000VDC models Pin Out Specifications Pin Single 1 2 3 4 - V Input +V Input -V Output +V Output Dimensions 11.70 (0.46) 6.00 (0.24) PRINTED FACE 10.00 (0.39) 9.50 (0.37) 0.50 (0.02) 4.10 . (0.16) 2.54 (0.10 ) 0.50 (0.02) 0.90 (0.04) 0.30 (0.01) 6.00 (0.24) 0.50 (0.02) www.aimtec.com F 051e R11.I Tel: +1 514 620 2722 2 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM1S-NZ 1 Watt | DC-DC Converter Typical Characteristics Tolerance Envelope Graph +10% Typic +5% +2.5% line -2.5% Output Voltage (%) Nominal Voltage al loa d -7.5% 10% 50% 100% Output Current (%) External capacitor Vin (VDC) 5 12 24 - External capacitor (uF) 4.7 2.2 1 Filtering Vout (VDC) 5 9 12 15 External capacitor (uF) 10 4.7 2.2 1 NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R11.I Tel: +1 514 620 2722 3 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only