Ordering number : ENA2060 LB1935FA Monolithic Digital IC Stepping Motor Driver IC http://onsemi.com Overview LB1935FA is IC with forward/reverse motor drive 2-channel in which low saturation voltage and low voltage operation possible. Its small sized package is optimal for 2 phase excitation drive of 2 phase bipolar stepping motors for various portable devices such as digital still cameras. Features • Low saturation voltage, VO (sat) = 0.3V typ at IO = 150mA • Built-in shoot-through current protection circuit • No standby current consumption (or zero) • Built-in thermal shutdown circuit • Micro10 small-sized package Absolute Maximum Ratings at Ta = 25°C Parameter Symbol Conditions Ratings Unit Maximum power source voltage VCC max Applied output voltage VOUT max OUT1, OUT2, OUT3, OUT4 pin Applied input voltage VIN max ENA, IN1, IN2 pin GND Pin outflow current I GND Per channel Allowable power dissipation Pd max With substrate* Operating temperature Topr -20 to +75 °C Storage temperature Tstg -40 to +150 °C -0.3 to +8.0 V VCC+VSF V -0.3 to +8.0 V 400 mA 400 mW * Specified substrate: 20.0mm×10.0mm×0.8mm, paper phenol Caution 1) Absolute maximum ratings represent the value which cannot be exceeded for any length of time. Caution 2) Even when the device is used within the range of absolute maximum ratings, as a result of continuous usage under high temperature, high current, high voltage, or drastic temperature change, the reliability of the IC may be degraded. Please contact us for the further details. Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Semiconductor Components Industries, LLC, 2013 June, 2013 52312 SY 20120514-S00001 No.A2060-1/4 LB1935FA Allowable Operating Range at Ta = 25°C Parameter Symbol Source voltage VCC Input high level voltage VIH Input low level voltage VIL Conditions Ratings Unit 2.2 to 7.5 V ENA, IN1, IN2 pin 1.8 to 7.5 V ENA, IN1, IN2 pin -0.3 to +0.7 V Electric Characteristics at Ta = 25°C, VCC = 3.3V Parameter Symbol Ratings Conditions min Power source current Output saturation voltage Input current Unit typ max 1 μA 13 19 mA 0.2 0.3 V 0.4 0.6 V VIN = 3V 40 60 μA VENA = 3V 40 60 μA 1 μA 1.7 V ICC0 ENA = 0V, VIN = 3V or 0V ICC1 ENA = 3V, VIN = 3V or 0V VOUT1 ENA = 3V, VIN = 3V or 0V, IOUT = 100mA VOUT2 ENA = 3V, VIN = 3V or 0V, IOUT = 200mA IIN IENA 0.1 Spark killer diode Reverse current IS(leak) Forward voltage VSF IOUT = 200mA Package Dimensions unit : mm (typ) 3428 3.0 Pd max -- Ta Allowable power dissipation, Pd max -- mW 500 0.55 4.9 3.0 10 1 2 0.5 0.16 1.03 0.25 Specified Substrate : 20.0×10.0×0.8mm3 Peper phenol 400 300 240 200 100 0 -20 0 20 40 60 80 100 0.1 Ambient temperature, Ta -- °C SANYO : Micro10 Pin Assignments VCC 1 10 OUT4 IN2 2 9 OUT3 ENA 3 8 OUT1 IN1 4 7 OUT2 (NC) 5 6 GND LB1935FA Top view No.A2060-2/4 LB1935FA Block Diagram Truth Table Input ENA IN1 Output IN2 OUT1 OUT2 OUT3 OUT4 Remarks L - - OFF OFF OFF OFF Standby H L L H L H L 2-phase excitation L H H L L H H H L H L H H L L H H L No.A2060-3/4 LB1935FA Timing Chart Timing chart below shows the 2 phase excitation stepping motor. ENA IN1 IN2 OUT1 OUT2 OUT3 OUT4 ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PS No.A2060-4/4