Finisar Product Specification OC-12 LR-2/STM L-4.2 Pluggable SFP Transceiver FTRJ1522P1xTL PRODUCT FEATURES • 622 Mb/s bi-directional data links • Hot-pluggable SFP footprint • Built-in digital diagnostic functions • Uncooled DFB 1550nm laser transmitter • Duplex LC connector • Very low jitter • Metal enclosure, for lower EMI • Single 3.3V power supply • Low power dissipation <700mW typical • Industrial operating temperature range: -40°C to 85°C APPLICATIONS • SONET OC-12 LR-2 / SDH STM L-4.2 Finisar’s FTRJ1522P1xTL Small Form Factor Pluggable (SFP) transceivers are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA)1. They comply with SONET and SDH standards2 at OC-12 LR-2/STM L-4.2. Digital diagnostics functions are available via the 2-wire serial bus specified in the SFP MSA. PRODUCT SELECTION FTRJ1522P1xTL x W B Finisar Corporation April 26, 2005 Rev.D Wide Extraction Bail Narrow Extraction Bail Page 1 Finisar FTRJ1522P1xTL Pluggable SFP Product Specification - April 2005 I. Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Pin Descriptions Symbol VEET TFAULT TDIS MOD_DEF(2) MOD_DEF(1) MOD_DEF(0) Rate Select LOS VEER VEER VEER RDRD+ VEER VCCR VCCT VEET TD+ TDVEET Name/Description Transmitter Ground (Common with Receiver Ground) Transmitter Fault. Not supported. Transmitter Disable. Laser output disabled on high or open. Module Definition 2. Data line for Serial ID. Module Definition 1. Clock line for Serial ID. Module Definition 0. Grounded within the module. No connection required Loss of Signal indication. Logic 0 indicates normal operation. Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Inverted DATA out. AC Coupled. Receiver Non-inverted DATA out. AC Coupled. Receiver Ground (Common with Transmitter Ground) Receiver Power Supply Transmitter Power Supply Transmitter Ground (Common with Receiver Ground) Transmitter Non-Inverted DATA in. AC Coupled. Transmitter Inverted DATA in. AC Coupled. Transmitter Ground (Common with Receiver Ground) Ref. 1 2 3 3 3 4 5 1 1 1 1 1 1 Notes: 1. Circuit ground is internally isolated from chassis ground. 2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V. 3. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.5V. MOD_DEF(0) pulls line low to indicate module is plugged in. 4. Finisar FTRJ1522P1xTL transceivers operate without active control. 5. LOS is open collector output. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.5V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. Towards Bezel 1 VeeT 2 TXFault 3 TX Disable 4 MOD-DEF(2) 5 MOD-DEF(1) 6 MOD-DEF(0) 7 Rate Select 8 LOS 9 VeeR 10 VeeR VeeT 20 TD- 19 TD+ 18 VeeT 17 VccT 16 VccR 15 VeeR 14 RD+ 13 RD- 12 VeeR 11 Towards ASIC Pinout of Connector Block on Host Board Finisar Corporation April 26, 2005 Rev.D Page 2 Finisar FTRJ1522P1xTL Pluggable SFP Product Specification - April 2005 II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity III. Symbol Vcc TS TOP RH Min -0.5 -40 -40 0 Typ Max 4.5 100 85 85 Unit V °C °C % Ref. 1 Electrical Characteristics (TOP = -40 to 85 °C, VCC = 3.10 to 3.50 Volts) Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing Transmit Disable Voltage Transmit Enable Voltage Transmit Disable Assert Time Receiver Single ended data output swing Data rise/fall time LOS Fault LOS Normal Power Supply Rejection Symbol Vcc Icc Rin Vin,pp VD VEN Vout,pp tr VLOS fault VLOS norm PSR Min 3.10 Typ Max 3.50 300 Unit V mA Ref. 2 1200 Vcc Vee+ 0.8 10 Ω mV V V µs mV ps V V mVpp 4 5 6 6 7 100 250 Vcc – 1.3 Vee 300 Vcc – 0.5 Vee 100 400 150 800 300 VccHOST Vee+0.5 3 Notes: 1. Non condensing. 2. AC coupled. 3. Or open circuit. 4. Into 100 ohm differential termination. 5. 20 – 80 % 6. Loss Of Signal is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected. 7. All transceiver specifications are compliant with a power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the power supply filtering network shown on page 23 of the Small Form-factor Pluggable (SFP) Transceiver MultiSource Agreement (MSA), September 14, 2000. Finisar Corporation April 26, 2005 Rev.D Page 3 Finisar FTRJ1522P1xTL Pluggable SFP Product Specification - April 2005 IV. Optical Characteristics (TOP = -40 to 85 °C, VCC = 3.10 to 3.50 Volts) Parameter Transmitter Output Opt. Pwr: 9/125 SMF Optical Wavelength Spectral Width (-20 dB) Optical Extinction Ratio Optical Rise/Fall Time Relative Intensity Noise Generated Jitter (peak to peak) Generated Jitter (rms) Mask Margin Receiver Average Rx Sensitivity Maximum Input Power Optical Center Wavelength LOS De-Assert LOS Assert LOS Hysteresis Max Receiver Reflectance Symbol Min POUT λ σ ER tr/ tf RIN JTXp-p JTXrms -3 1480 Typ Max Unit 2 1580 1 dBm nm nm dB ps dB/Hz UI UI 1 dBm dBm nm dBm dBm dB dB 4 10 300 -120 0.07 0.007 Ref. 2 3 3 20% RSENS1 PMAX λC LOSD LOSA RxR -28 -8 1260 -8 1600 -28 -45 0.5 -27 Notes: 1. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations. 2. Unfiltered, 20-80% 3. Jitter measurements taken using Agilent OMNIBERT 718 in accordance with GR-253. 4. With worst-case extinction ratio. Measured with a PRBS 223-1 test pattern. Finisar Corporation April 26, 2005 Rev.D Page 4 Finisar FTRJ1522P1xTL Pluggable SFP Product Specification - April 2005 V. General Specifications Parameter Data Rate Bit Error Rate Max. Supported Link Length on 9/125µm SMF @ OC-12 Symbol BR BER LMAX4 Min 622 Typ Max 622 10-12 80 Units Ref. Mb/sec 1 2 km 3 Notes: 1. Compliant with SONET and SDH at the OC-12 LR-2/STM L-4.2. 2. Tested with a PRBS 223-1 test pattern. 3. Attenuation of 0.275 dB/km is used for the link length calculations (per GR-253 CORE). Distances are indicative only. Please refer to the Optical Specifications in Table IV to calculate a more accurate link budget based on specific conditions in your application. VI. Environmental Specifications Finisar 1550nm SFP transceivers have an industrial operating temperature range from –40°C to +85°C case temperature. Parameter Case Operating Temperature Storage Temperature VII. Symbol Top Tsto Min -40 -40 Typ Max 85 100 Units °C °C Ref. Regulatory Compliance Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations. These products are certified by TÜV and CSA to meet the Class 1 eye safety requirements of EN (IEC) 60825 and the electrical safety requirements of EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request. Finisar Corporation April 26, 2005 Rev.D Page 5 FTRJ1522P1xTL Pluggable SFP Product Specification - April 2005 Finisar VIII. Digital Diagnostic Functions Finisar FTRJ1522P1xTL SFP transceivers support the 2-wire serial communication protocol as defined in the SFP MSA1. It is very closely related to the E2PROM defined in the GBIC standard, with the same electrical specifications. The standard SFP serial ID provides access to identification information that describes the transceiver’s capabilities, standard interfaces, manufacturer, and other information. Additionally, Finisar SFP transceivers provide a unique enhanced digital diagnostic monitoring interface, which allows real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage. It also defines a sophisticated system of alarm and warning flags, which alerts end-users when particular operating parameters are outside of a factory-set normal range. The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a 2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally defined serial ID memory map remains unchanged. The interface is identical to, and is thus fully backward compatible with both the GBIC Specification and the SFP Multi Source Agreement. The complete interface is described in Finisar Application Note AN-2030: “Digital Diagnostics Monitoring Interface for SFP Optical Transceivers”. The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through a 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the SFP transceiver into those segments of the E2PROM that are not write-protected. The negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. For more information, please see the SFP MSA documentation1 or Finisar Application Note AN-2030. Digital diagnostics for the FTRJ1522P1xTL are externally calibrated by default. Please note that evaluation board FDB-1018 is available with Finisar ModDEMO software that allows simple to use communication over the 2-wire serial interface. Finisar Corporation April 26, 2005 Rev.D Page 6 FTRJ1522P1xTL Pluggable SFP Product Specification - April 2005 IX. Finisar Mechanical Specifications Finisar’s Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA) 3. FTRJ1522P1BTL Finisar Corporation April 26, 2005 Rev.D Page 7 FTRJ1522P1xTL Pluggable SFP Product Specification - April 2005 Finisar FTRJ1522P1WTL Finisar Corporation April 26, 2005 Rev.D Page 8 FTRJ1522P1xTL Pluggable SFP Product Specification - April 2005 X. Finisar PCB Layout and Bezel Recommendations Finisar Corporation April 26, 2005 Rev.D Page 9 FTRJ1522P1xTL Pluggable SFP Product Specification - April 2005 Finisar Corporation April 26, 2005 Rev.D Finisar Page 10 FTRJ1522P1xTL Pluggable SFP Product Specification - April 2005 XI. Finisar References 1. Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 2000. Documentation is currently available at Finisar upon request. 2. Bellcore GR-253 and ITU-T G.957 Specifications. XII. For More Information Finisar Corporation 1308 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 [email protected] www.finisar.com Finisar Corporation April 26, 2005 Rev.D Page 11