Maxim MAX1473EUI+ 315mhz/433mhz ask superheterodyne receiver with extended dynamic range Datasheet

19-2748; Rev 6; 1/12
KIT
ATION
EVALU
LE
B
A
IL
A
AV
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
The MAX1473 fully integrated low-power CMOS superheterodyne receiver is ideal for receiving amplitudeshift-keyed (ASK) data in the 300MHz to 450MHz
frequency range. Its signal range is from -114dBm to
0dBm. With few external components and a low-current
power-down mode, it is ideal for cost- and power-sensitive applications typical in the automotive and consumer
markets. The chip consists of a low-noise amplifier
(LNA), a fully differential image-rejection mixer, an onchip phase-locked-loop (PLL) with integrated voltagecontrolled oscillator (VCO), a 10.7MHz IF limiting
amplifier stage with received-signal-strength indicator
(RSSI), and analog baseband data-recovery circuitry.
The MAX1473 also has a discrete one-step automatic
gain control (AGC) that drops the LNA gain by 35dB
when the RF input signal is greater than -57dBm.
The MAX1473 is available in 28-pin TSSOP and 32-pin
thin QFN packages. Both versions are specified for the
extended (-40°C to +85°C) temperature range.
Features
o Optimized for 315MHz or 433MHz ISM Band
o Operates from Single 3.3V or 5.0V Supplies
o High Dynamic Range with On-Chip AGC
o Selectable Image-Rejection Center Frequency
o Selectable x64 or x32 fLO/fXTAL Ratio
o Low 5.2mA Operating Supply Current
o < 2.5µA Low-Current Power-Down Mode for
Efficient Power Cycling
o 250µs Startup Time
o Built-In 50dB RF Image Rejection
o Receive Sensitivity of -114dBm
Ordering Information
PART
Applications
Automotive Remote Keyless Entry
Garage Door Openers
Security Systems
Home Automation
Remote Controls
Wireless Sensors
Local Telemetry
Systems
TEMP RANGE
PIN-PACKAGE
MAX1473EUI+
-40°C to +85°C
28 TSSOP
MAX1473ETJ+
-40°C to +85°C
32 Thin QFN-EP*
+Denotes a lead(Pb)-free/RoHS-compliant package.
*EP = Exposed pad.
Functional Diagram and Typical Application Circuit appear
at end of data sheet.
LNASRC 4
25 DATAOUT
AGND 5
LNAOUT 6
MAX1473
XTAL1
XTAL2
PWRDN
PDOUT
N.C.
28
27
26
25
+
AVDD
26 PDOUT
29
27 PWRDN
30
AVDD 2
LNAIN 3
LNAIN
28 XTAL2
LNASRC
+
XTAL1 1
31
TOP VIEW
32
Pin Configurations
N.C.
1
24
DATAOUT
24 VDD5
AGND
2
23
VDD5
23 DSP
LNAOUT
3
22
DSP
AVDD
4
21
N.C.
AVDD 7
22 DFFB
MIXIN1 8
21 OPP
MIXIN1
5
20
DFFB
MIXIN2 9
20 DSN
MIXIN2
6
19
OPP
AGND 10
19 DFO
AGND
7
18
DSN
IRSEL 11
18 IFIN2
IRSEL
8
17
DFO
MIXOUT 12
17 IFIN1
13
14
15
16
IFIN1
IFIN2
12
N.C.
11
DVDD
AGCDIS
XTALSEL
9
TSSOP
10
15 AGCDIS
DGND
16 XTALSEL
DVDD 14
MIXOUT
DGND 13
MAX1473
THIN QFN
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
1
MAX1473
General Description
MAX1473
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
ABSOLUTE MAXIMUM RATINGS
VDD5 to AGND.......................................................-0.3V to +6.0V
AVDD to AGND .....................................................-0.3V to +4.0V
DVDD to DGND .....................................................-0.3V to +4.0V
AGND to DGND.....................................................-0.1V to +0.1V
IRSEL, DATAOUT, XTALSEL, AGCDIS,
PWRDN to AGND .....................................-0.3V to (VDD5 + 0.3V)
All Other Pins to AGND ..............................-0.3V to (VDD + 0.3V)
Continuous Power Dissipation (TA = +70°C)
28-Pin TSSOP (derate 12.8mW/°C above +70°C) .1025.6mW
32-Pin Thin QFN (derate 21.3mW/°C
above +70°C).........................................................1702.1mW
Operating Temperature Ranges
MAX1473E__ ..................................................-40°C to +85°C
Storage Temperature Range .............................-60°C to +150°C
Lead Temperature (soldering 10s) ..................................+300°C
Soldering Temperature (reflow) .......................................+260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS (3.3V OPERATION)
(Typical Application Circuit, VDD = 3.0V to 3.6V, no RF signal applied, TA = -40°C to +85°C, unless otherwise noted. Typical values
are at VDD = 3.3V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
3.0
3.3
3.6
V
fRF = 315MHz
5.2
6.23
fRF = 433MHz
5.8
6.88
fRF = 315MHz
1.6
fRF = 433MHz
2.5
Supply Voltage
VDD
3.3V nominal supply
Supply Current
IDD
V P WRDN = VDD
IPWRDN
V P WRDN = 0V,
VXTALSEL = 0V
Shutdown Supply Current
Input Voltage Low
VIL
Input Voltage High
VIH
Input Logic Current High
IIH
0.4
VDD - 0.4
DATAOUT Voltage Output Low
VOL
DATAOUT Voltage Output High
VOH
10
2
V
µA
VDD - 0.4
fRF = 375MHz, VIRSEL = VDD/2
1.1
fRF = 315MHz, VIRSEL = 0V
0.4
RL = 5kΩ
µA
V
fRF = 433MHz, VIRSEL = VDD
Image Reject Select (Note 2)
5.3
mA
VDD - 0.4
_______________________________________________________________________________________
VDD - 1.5
V
0.4
V
V
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
(Typical Application Circuit, VDD = 4.5V to 5.5V, no RF signal applied, TA = -40°C to +85°C, unless otherwise noted. Typical values
are at VDD = 5.0V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
4.5
5.0
5.5
V
fRF = 315MHz
5.2
6.04
fRF = 433MHz
5.7
6.76
fRF = 315MHz
2.3
fRF = 433MHz
2.8
Supply Voltage
VDD
5.0V nominal supply
Supply Current
IDD
V P WRDN = VDD
IPWRDN
V P WRDN = 0V,
VXTALSEL = 0V
Shutdown Supply Current
Input Voltage Low
VIL
Input Voltage High
VIH
Input Logic Current High
IIH
0.4
VDD - 0.4
fRF = 375MHz, VIRSEL = VDD/2
VOL
DATAOUT Voltage Output High
VOH
µA
1.1
VDD - 1.5
V
0.4
0.4
RL = 5kΩ
V
VDD - 0.4
fRF = 315MHz, VIRSEL = 0V
DATAOUT Voltage Output Low
µA
V
10
fRF = 433MHz, VIRSEL = VDD
Image Reject Select (Note 2)
6.2
mA
VDD - 0.4
V
V
AC ELECTRICAL CHARACTERISTICS
(Typical Application Circuit, VDD = 3.0V to 3.6V, all RF inputs are referenced to 50Ω, fRF = 315MHz, TA = -40°C to +85°C, unless
otherwise noted. Typical values are at VDD = 3.3V and TA = +25°C.) (Note 1).
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
GENERAL CHARACTERISTICS
Startup Time
tON
Receiver Input Frequency
Time for valid signal detection after
V P WRDN = VOH
fRF
300
Maximum Receiver Input Level
PRFIN_MAX Modulation depth > 18dB
Sensitivity (Note 3)
PRFIN_MIN
AGC Hysteresis
250
Peak power level
LNA gain from low to high
µs
450
MHz
0
dBm
-114
dBm
8
dB
150
ms
16
dB
LNA IN HIGH-GAIN MODE
Power Gain
Input Impedance (Note 4)
1dB Compression Point
Input-Referred 3rd-Order
Intercept
ZIN_LNA
Normalized to
50Ω
fRF = 433MHz
1 - j3.4
fRF = 375MHz
1 - j3.9
fRF = 315MHz
1 - j4.7
P1dBLNA
-22
dBm
IIP3LNA
-12
dBm
_______________________________________________________________________________________
3
MAX1473
DC ELECTRICAL CHARACTERISTICS (5.0V OPERATION)
MAX1473
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
AC ELECTRICAL CHARACTERISTICS (continued)
(Typical Application Circuit, VDD = 3.0V to 3.6V, all RF inputs are referenced to 50Ω, fRF = 315MHz, TA = -40°C to +85°C, unless
otherwise noted. Typical values are at VDD = 3.3V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
LO Signal Feedthrough to
Antenna
Noise Figure
NFLNA
MIN
TYP
MAX
UNITS
-80
dBm
2
dB
LNA IN LOW-GAIN MODE
Input Impedance (Note 4)
1dB Compression Point
Input-Referred 3rd-Order
Intercept
ZIN_LNA
Normalized to
50Ω
fRF = 433MHz
1 - j3.4
fRF = 375MHz
1 - j3.9
fRF = 315MHz
1 - j4.7
P1dBLNA
-10
dBm
IIP3LNA
-7
dBm
-80
dBm
LO Signal Feedthrough to
Antenna
Noise Figure
NFLNA
2
dB
0
dB
35
dB
IIP3MIX
-18
dBm
ZOUT_MIX
330
Ω
NFMIX
16
dB
Power Gain
Voltage Gain Reduction
AGC enabled (depends on tank Q)
MIXER
Input-Referred 3rd-Order
Intercept
Output Impedance
Noise Figure
Image Rejection
(not Including LNA Tank)
Conversion Gain
fRF = 433MHz, VIRSEL = VDD
42
fRF = 375MHz, VIRSEL = VDD/2
44
fRF = 315MHz, VIRSEL = 0V
44
330Ω IF filter load
13
dB
dB
INTERMEDIATE FREQUENCY (IF)
Input Impedance
Operating Frequency
ZIN_IF
fIF
Bandpass response
3dB Bandwidth
RSSI Linearity
RSSI Dynamic Range
RSSI Level
4
Ω
MHz
20
MHz
±0.5
dB
80
dB
PRFIN < -120dBm
1.15
PRFIN > 0dBm, AGC enabled
2.35
RSSI Gain
AGC Threshold
330
10.7
14.2
LNA gain from low to high
1.45
LNA gain from high to low
2.05
_______________________________________________________________________________________
V
mV/dB
V
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
(Typical Application Circuit, VDD = 3.0V to 3.6V, all RF inputs are referenced to 50Ω, fRF = 315MHz, TA = -40°C to +85°C, unless
otherwise noted. Typical values are at VDD = 3.3V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DATA FILTER
Maximum Bandwidth
BWDF
100
kHz
BWCMP
100
kHz
Output High Voltage
VDD5
V
Output Low Voltage
0
V
DATA SLICER
Comparator Bandwidth
CRYSTAL OSCILLATOR
fRF = 433MHz
Crystal Frequency (Note 5)
fXTAL
fRF = 315MHz
VXTALSEL = 0V
6.6128
VXTALSEL = VDD
13.2256
VXTALSEL = 0V
4.7547
VXTALSEL = VDD
9.5094
Crystal Tolerance
Input Capacitance
From each pin to ground
MHz
MHz
50
ppm
6.2
pF
Recommended Crystal Load
Capacitance
CLOAD
3
pF
Maximum Crystal Load
Capacitance
CLOAD
10
pF
Note 1: 100% tested at TA = +25°C. Guaranteed by design and characterization over temperature.
Note 2: IRSEL is internally set to 375MHz IR mode. It can be left open when the 375MHz image rejection setting is desired. A 1nF
capacitor is recommended in noisy environments.
Note 3: BER = 2 x 10-3, Manchester encoded, data rate = 4kbps, IF bandwidth = 280kHz.
Note 4: Input impedance is measured at the LNAIN pin. Note that the impedance includes the 15nH inductive degeneration connected from the LNA source to ground. The equivalent input circuit is 50Ω in series with 2.2pF.
Note 5: Crystal oscillator frequency for other RF carrier frequency within the 300MHz to 450MHz range is (fRF - 10.7MHz)/64 for
XTALSEL = 0V, and (fRF - 10.7MHz)/32 for XTALSEL = VDD.
_______________________________________________________________________________________
5
MAX1473
AC ELECTRICAL CHARACTERISTICS (continued)
Typical Operating Characteristics
(Typical Application Circuit, VDD = 3.3V, fRF = 315MHz, TA = +25°C, unless otherwise noted.)
SUPPLY CURRENT
vs. RF FREQUENCY
+85°C
5.3
+25°C
5.2
5.1
MAX1473 toc02
100
fRF = 433MHz
10
+105°C
BIT-ERROR RATE (%)
SUPPLY CURRENT (mA)
5.4
6.5
SUPPLY CURRENT (mA)
+105°C
5.5
7.0
MAX1473 toc01
5.6
BIT-ERROR RATE
vs. AVERAGE RF INPUT POWER
MAX1473 toc03
SUPPLY CURRENT
vs. SUPPLY VOLTAGE
6.0
5.5
+85°C
1
fRF = 315MHz
0.1
+25°C
5.0
-40°C
-40°C
4.9
3.1
3.2
3.3
3.4
3.5
3.6
350
400
450
RF FREQUENCY (MHz)
SENSITIVITY vs. TEMPERATURE
RSSI vs. RF INPUT POWER
-121 -120
500
IF BANDWIDTH = 280kHz
2.2
VAGCDIS = VDD
MAX1473 toc06
2.4
2.0
3.5
2.2
2.5
2.0
1.5
1.8
0.5
-110
-112
1.8
VAGCDIS = 0V
1.6
1.4
1.6
-1.5
1.4
fRF = 315MHz
1.2
1.0
0
20
40
60
TEMPERATURE (°C)
SYSTEM GAIN vs. FREQUENCY
10
50dB IMAGE
REJECTION
0
LOWER
SIDEBAND
-10
FROM RFIN TO
MIXOUT
fRF = 315MHz
-20
-60
-40
-20
0
5
10
15
20
IF FREQUENCY (MHz)
25
-30
IMAGE REJECTION
vs. RF FREQUENCY
IMAGE REJECTION
vs. TEMPERATURE
50
45
40
fRF = 375MHz
-10
10
60
85
45
fRF = 315MHz
45
44
44
43
fRF = 375MHz
43
42
fRF = 433MHz
42
fRF = 315MHz
fRF = 433MHz
30
-50
IF INPUT POWER (dBm)
41
30
0
-70
RF INPUT POWER (dBm)
35
-30
-3.5
-90
MAX1473 toc08
20
-80
55
IMAGE REJECTION (dB)
UPPER
SIDEBAND
MAX1473 toc07
30
-2.5
1.0
-140 -120 -100
80 100 120
IMAGE REJECTION (dB)
-40 -20
RSSI
1.2
-116
-118
-0.5
DELTA
MAX1473 toc09
fRF = 433MHz
-108
RSSI (V)
RSSI (V)
-106
-114
6
-119 -118 -117 -116 -115 -114
AVERAGE INPUT POWER (dBm)
RSSI AND DELTA
vs. IF INPUT POWER
2.4
MAX1473 toc04
PEAK RF INPUT POWER
0.2% BER
IF BANDWIDTH = 280kHz
-104
300
SUPPLY VOLTAGE (V)
-100
-102
250
MAX1473 toc05
3.0
SENSITIVITY (dBm)
0.01
4.5
41
280
330
380
430
RF FREQUENCY (MHz)
480
-40
-15
10
35
TEMPERATURE (°C)
_______________________________________________________________________________________
DELTA (dB)
5.0
SYSTEM GAIN (dB)
MAX1473
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
NORMALIZED IF GAIN
vs. IF FREQUENCY
-5
-10
MAX1473 toc12
MAX1473 toc11
MAX1473 toc10
0
S11 SMITH PLOT OF RFIN
S11 MAGNITUDE-LOG PLOT OF RFIN
30
20
10
MAGNITUDE (dB)
NORMALIZED IF GAIN (dB)
5
600MHz
0
-10
-20
100MHz
-30
-40
-15
-50
-20
-70
315MHz
-34dB
-60
RF FREQUENCY (MHz)
REGULATOR VOLTAGE
vs. REGULATOR CURRENT
PHASE NOISE
vs. OFFSET FREQUENCY
0
MAX1473 toc13
-40°C
2.9
+25°C
+85°C
+105°C
2.8
2.7
2.6
VDD = 5.0V
2.5
5
15
25
35
REGULATOR CURRENT (mA)
-20
PHASE NOISE (dBc/Hz)
3.0
45
fRF = 315MHz
PHASE NOISE
vs. OFFSET FREQUENCY
0
-40
-60
-80
-100
fRF = 433MHz
-20
PHASE NOISE (dBc/Hz)
3.1
REGULATOR VOLTAGE (V)
10 109 208 307 406 505 604 703 802 901 1000
100
MAX1473 toc15
10
IF FREQUENCY (MHz)
MAX1473 toc14
1
-40
-60
-80
-100
-120
-120
-140
1.E-05 1.E-04 1.E-03 1.E-02 1.E-01 1.E+00 1.E+01
-140
1.E-05 1.E-04 1.E-03 1.E-02 1.E-01 1.E+00 1.E+01
OFFSET FREQUENCY (MHz)
OFFSET FREQUENCY (MHz)
_______________________________________________________________________________________
7
MAX1473
Typical Operating Characteristics (continued)
(Typical Application Circuit, VDD = 3.3V, fRF = 315MHz, TA = +25°C, unless otherwise noted.)
MAX1473
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
Pin Description
PIN
TSSOP
TQFN
1
29
8
NAME
XTAL1
FUNCTION
1st Crystal Input. (See the Phase-Locked Loop section.)
Positive Analog Supply Voltage. For +5V operation, pin 2 is the output of an on-chip +3.2V
low-dropout regulator and should be bypassed to AGND with a 0.1µF capacitor as close as
possible to the pin. Pin 7 must be externally connected to the supply from pin 2 and bypassed to
AGND with a 0.01µF capacitor as close as possible to the pin (see the Voltage Regulator section
and the Typical Application Circuit).
Low-Noise Amplifier Input. (See the Low-Noise Amplifier section.)
2, 7
4, 30
AVDD
3
31
LNAIN
4
32
LNASRC
5
2
AGND
6
3
LNAOUT
8
5
MIXIN1
9
6
MIXIN2
2nd Differential Mixer Input. Connect through a 100pF capacitor to LC tank filter from LNAOUT.
10
7
AGND
Analog Ground
11
8
IRSEL
Image Rejection Select Pin. Set VIRSEL = 0V to center image rejection at 315MHz. Leave IRSEL
unconnected to center image rejection at 375MHz. Set VIRSEL = VDD to center image rejection at 433MHz.
12
9
MIXOUT
13
10
DGND
Digital Ground
Positive Digital Supply Voltage. Connect to both of the AVDD pins. Bypass to DGND with a 0.01µF
capacitor as close as possible to the pin (see the Typical Application Circuit).
14
11
DVDD
15
12
AGCDIS
Low-Noise Amplifier Source for External Inductive Degeneration. Connect inductor to ground to set
LNA input impedance. (See the Low-Noise Amplifier section.)
Analog Ground
Low-Noise Amplifier Output. Connect to mixer through an LC tank filter. (See the Low-Noise
Amplifier section.)
1st Differential Mixer Input. Connect through a 100pF capacitor to VDD3 side of the LC tank.
330Ω Mixer Output. Connect to the input of the 10.7MHz bandpass filter.
AGC Control Pin. Pull high to disable AGC.
Crystal Divider Ratio Select Pin. Drive XTALSEL low to select divider ratio of 64, or drive XTALSEL
high to select divider ratio of 32.
1st Differential Intermediate Frequency Limiter Amplifier Input. Decouple to AGND with a 1500pF
capacitor.
2nd Differential Intermediate Frequency Limiter Amplifier Input. Connect to the output of a 10.7MHz
bandpass filter.
16
14
XTALSEL
17
15
IFIN1
18
16
IFIN2
19
17
DFO
Data Filter Output
20
18
DSN
Negative Data Slicer Input
21
19
OPP
Noninverting Op-Amp Input for the Sallen-Key Data Filter
22
20
DFFB
Data Filter Feedback Node. Input for the feedback of the Sallen-Key data filter.
23
22
DSP
Positive Data Slicer Input
24
23
VDD5
+5V Supply Voltage. Bypass to AGND with a 0.01µF capacitor as close as possible to the pin. For
+5V operation, VDD5 is the input to an on-chip voltage regulator whose +3.2V output appears at the
pin 2 AVDD pin. (See the Voltage Regulator section and the Typical Application Circuit.)
25
24
26
26
PDOUT
Peak Detector Output
27
27
PWRDN
Power-Down Select Input. Drive this pin with a logic high to power on the IC.
28
28
XTAL2
—
1, 13,
21, 25
N.C.
—
—
EP
DATAOUT Digital Baseband Data Output
2nd Crystal Input
No Connection
Exposed Pad (TQFN Only). Connect EP to GND.
_______________________________________________________________________________________
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
The MAX1473 CMOS superheterodyne receiver and a
few external components provide the complete receive
chain from the antenna to the digital output data.
Depending on signal power and component selection,
data rates as high as 100kbps can be achieved.
The MAX1473 is designed to receive binary ASK data
modulated in the 300MHz to 450MHz frequency range.
ASK modulation uses a difference in amplitude of the
carrier to represent logic 0 and logic 1 data.
Voltage Regulator
For operation with a single +3.0V to +3.6V supply voltage, connect AVDD, DVDD, and VDD5 to the supply
voltage. For operation with a single +4.5V to +5.5V
supply voltage, connect VDD5 to the supply voltage. An
on-chip voltage regulator drives one of the AVDD pins
to approximately +3.2V. For proper operation, DVDD
and both the AVDD pins must be connected together.
Bypass VDD5, DVDD, and the pin 7 AVDD pin to AGND
with 0.01µF capacitors, and the pin 2 AVDD pin to
AGND with a 0.1µF capacitor, all placed as close as
possible to the pins.
Low-Noise Amplifier
The LNA is an NMOS cascode amplifier with off-chip
inductive degeneration that achieves approximately
16dB of power gain with a 2.0dB noise figure and an
IIP3 of -12dBm. The gain and noise figure are dependent on both the antenna matching network at the LNA
input and the LC tank network between the LNA output
and the mixer inputs.
The off-chip inductive degeneration is achieved by
connecting an inductor from LNASRC to AGND. This
inductor sets the real part of the input impedance at
LNAIN, allowing for a more flexible input impedance
match, such as a typical PCB trace antenna. A nominal
value for this inductor with a 50Ω input impedance is
15nH, but is affected by PCB trace. See the Typical
Operating Characteristics for the relationship between
the inductance and the LNA input impedance.
The AGC circuit monitors the RSSI output. When the
RSSI output reaches 2.05V, which corresponds to an
RF input level of approximately -57dBm, the AGC
switches on the LNA gain reduction resistor. The resistor reduces the LNA gain by 35dB, thereby reducing
the RSSI output by about 500mV. The LNA resumes
high-gain mode when the RSSI level drops back below
1.45V (approximately -65dBm at RF input) for 150ms.
The AGC has a hysteresis of ~8dB. With the AGC func-
tion, the MAX1473 can reliably produce an ASK output
for RF input levels up to 0dBm with a modulation depth
of 18dB.
The LC tank filter connected to LNAOUT comprises L3
and C2 (see the Typical Application Circuit). Select L3
and C2 to resonate at the desired RF input frequency.
The resonant frequency is given by:
1
f =
2π L TOTAL × C TOTAL
where:
LTOTAL = L3 + LPARASITICS
CTOTAL = C2 + CPARASITICS
LPARASITICS and CPARASITICS include inductance and
capacitance of the PCB traces, package pins, mixer
input impedance, LNA output impedance, etc. These
parasitics at high frequencies cannot be ignored, and
can have a dramatic effect on the tank filter center frequency. Lab experimentation should be done to optimize the center frequency of the tank.
Mixer
A unique feature of the MAX1473 is the integrated
image rejection of the mixer. This device eliminates the
need for a costly front-end SAW filter for most applications. Advantages of not using a SAW filter are
increased sensitivity, simplified antenna matching, less
board space, and lower cost.
The mixer cell is a pair of double balanced mixers that
perform an IQ downconversion of the RF input to the
10.7MHz IF from a low-side injected LO (i.e., fLO = fRF fIF). The image-rejection circuit then combines these
signals to achieve a minimum 45dB of image rejection
over the full temperature range. Low-side injection is
required due to the on-chip image rejection architecture. The IF output is driven by a source-follower biased
to create a driving impedance of 330Ω; this provides a
good match to the off-chip 330Ω ceramic IF filter. The
voltage conversion gain is approximately 13dB when
the mixer is driving a 330Ω load.
The IRSEL pin is a logic input that selects one of the
three possible image-rejection frequencies. When
VIRSEL = 0V, the image rejection is tuned to 315MHz.
VIRSEL = VDD/2 tunes the image rejection to 375MHz,
and when VIRSEL = VDD, the image rejection is tuned to
433MHz. The IRSEL pin is internally set to VDD/2 (image
rejection at 375MHz) when it is left unconnected, thereby eliminating the need for an external VDD/2 voltage.
_______________________________________________________________________________________
9
MAX1473
Detailed Description
MAX1473
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
Phase-Locked Loop
The PLL block contains a phase detector, charge
pump/integrated loop filter, VCO, asynchronous 64x
clock divider, and crystal oscillator driver. Besides the
crystal, this PLL does not require any external components. The VCO generates a low-side local oscillator
(LO). The relationship between the RF, IF, and crystal
reference frequencies is given by:
fXTAL = (fRF - fIF)/(32 M)
where:
M = 1 (VXTALSEL = VDD) or 2 (VXTALSEL = 0V)
To allow the smallest possible IF bandwidth (for best sensitivity), the tolerance of the reference must be minimized.
Intermediate Frequency/RSSI
The IF section presents a differential 330Ω load to provide matching for the off-chip ceramic filter. The six
internal AC-coupled limiting amplifiers produce an
overall gain of approximately 65dB, with a bandpass filter-type response centered near the 10.7MHz IF frequency with a 3dB bandwidth of approximately
11.5MHz. The RSSI circuit demodulates the IF by producing a DC output proportional to the log of the IF signal level, with a slope of approximately 14.2mV/dB (see
the Typical Operating Characteristics).
The AGC circuit monitors the RSSI output. When the
RSSI output reaches 2.05V, which corresponds to an RF
input level of approximately -57dBm, the AGC switches
on the LNA gain reduction resistor. The resistor reduces
the LNA gain by 35dB, thereby reducing the RSSI output by about 500mV. The LNA resumes high-gain mode
when the RSSI level drops back below 1.45V (approximately -65dBm at RF input) for 150ms. The AGC has a
hysteresis of ~8dB. With the AGC function, the
MAX1473 can reliably produce an ASK output for RF
input levels up to 0dBm with modulation depth of 18dB.
Applications Information
Crystal Oscillator
The XTAL oscillator in the MAX1473 is designed to present a capacitance of approximately 3pF between the
XTAL1 and XTAL2. If a crystal designed to oscillate
with a different load capacitance is used, the crystal is
pulled away from its stated operating frequency, introducing an error in the reference frequency. Crystals
designed to operate with higher differential load capacitance always pull the reference frequency higher. For
example, a 4.7547MHz crystal designed to operate
with a 10pF load capacitance oscillates at 4.7563MHz
with the MAX1473, causing the receiver to be tuned to
315.1MHz rather than 315.0MHz, an error of about
100kHz, or 320ppm.
10
In actuality, the oscillator pulls every crystal. The crystal’s natural frequency is really below its specified frequency, but when loaded with the specified load
capacitance, the crystal is pulled and oscillates at its
specified frequency. This pulling is already accounted
for in the specification of the load capacitance.
Additional pulling can be calculated if the electrical
parameters of the crystal are known. The frequency
pulling is given by:
⎞
C ⎛
1
1
⎟ × 106
fp = m ⎜
2 ⎜⎝ Ccase + Cload Ccase + Cspec ⎟⎠
where:
fp is the amount the crystal frequency pulled in ppm.
Cm is the motional capacitance of the crystal.
Ccase is the case capacitance.
Cspec is the specified load capacitance.
Cload is the actual load capacitance.
When the crystal is loaded as specified, i.e., Cload =
Cspec, the frequency pulling equals zero.
Data Filter
The data filter is implemented as a 2nd-order lowpass
Sallen-Key filter. The pole locations are set by the combination of two on-chip resistors and two external
capacitors. Adjusting the value of the external capacitors changes the corner frequency to optimize for different data rates. The corner frequency should be set
to approximately 1.5 times the fastest expected data
rate from the transmitter. Keeping the corner frequency
near the data rate rejects any noise at higher frequencies, resulting in an increase in receiver sensitivity.
The configuration shown in Figure 1 can create a
Butterworth or Bessel response. The Butterworth filter
offers a very flat amplitude response in the passband
and a rolloff rate of 40dB/decade for the two-pole filter.
The Bessel filter has a linear phase response, which
works well for filtering digital data. To calculate the
value of C7 and C6, use the following equations along
with the coefficients in Table 1:
Table 1. Coefficents to Calculate C7 and C6
FILTER TYPE
a
b
Butterworth (Q = 0.707)
1.414
1.000
Bessel (Q = 0.577)
1.3617
0.618
______________________________________________________________________________________
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
b
a (100k )( π ) ( fc )
C6 =
a
4 (100k )( π ) ( fc )
Data Slicer
where fC is the desired 3dB corner frequency.
For example, choose a Butterworth filter response with
a corner frequency of 5kHz:
C7 =
1.000
(1.414 )(100kΩ)( 3.14 )( 5kHz )
≈ 450pF
Choosing standard capacitor values changes C7 to
470pF and C6 to 220pF, as shown in the Typical
Application Circuit.
MAX1473
RSSI
RDF1
100kΩ
RDF2
100kΩ
22
DFFB
21
OPP
19
DFO
C7
C6
The purpose of the data slicer is to take the analog output of the data filter and convert it to a digital signal.
This is achieved by using a comparator and comparing
the analog input to a threshold voltage. One input is
supplied by the data filter output. Both comparator
inputs are accessible off chip to allow for different
methods of generating the slicing threshold, which is
applied to the second comparator input.
The suggested data slicer configuration uses a resistor
(R1) connected between DSN and DSP with a capacitor (C8) from DSN to DGND (Figure 2). This configuration averages the analog output of the filter and sets the
threshold to approximately 50% of that amplitude. With
this configuration, the threshold automatically adjusts
as the analog signal varies, minimizing the possibility
for errors in the digital data. The sizes of R1 and C8
affect how fast the threshold tracks to the analog amplitude. Be sure to keep the corner frequency of the RC
circuit much lower than the lowest expected data rate.
Note that a long string of zeros or 1’s can cause the
threshold to drift. This configuration works best if a coding scheme, such as Manchester coding, which has an
equal number of zeros and 1’s, is used.
To prevent continuous toggling of DATAOUT in the
absence of an RF signal due to noise, hysteresis can
be added to the data slicer as shown in Figure 3.
For further information on Data Slicer options, please
refer to Maxim Application Note 3671, Data Slicing
Techniques for UHF ASK Receivers.
MAX1473
Figure 1. Sallen-Key Lowpass Data Filter
DATA
SLICER
MAX1473
25
DATAOUT
DATA
SLICER
20
DSN
23
DSP
R1
19
DFO
R2
R3
20
DSN
25
DATAOUT
23
DSP
19
DFO
R*
C8
*OPTIONAL
C8
R1
Figure 2. Generating Data Slicer Threshold
Figure 3. Generating Data Slicer Hysteresis
______________________________________________________________________________________
11
MAX1473
C7 =
MAX1473
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
Peak Detector
The peak detector output (PDOUT), in conjunction with
an external RC filter, creates a DC output voltage equal
to the peak value of the data signal. The resistor provides a path for the capacitor to discharge, allowing the
peak detector to dynamically follow peak changes of
the data filter output voltage. For faster receiver startup,
the circuit shown in Figure 4 can be used.
MAX1473
DATA
SLICER
Layout Considerations
A properly designed PCB is an essential part of any
RF/microwave circuit. On high-frequency inputs and
outputs, use controlled-impedance lines and keep
them as short as possible to minimize losses and radiation. At high frequencies, trace lengths that are on the
order of λ/10 or longer act as antennas.
Keeping the traces short also reduces parasitic inductance. Generally, 1in of a PCB trace adds about 20nH
of parasitic inductance. The parasitic inductance can
have a dramatic effect on the effective inductance of a
passive component. For example, a 0.5in trace connecting a 100nH inductor adds an extra 10nH of inductance or 10%.
To reduce the parasitic inductance, use wider traces
and a solid ground or power plane below the signal
traces. Also, use low-inductance connections to ground
on all GND pins, and place decoupling capacitors
close to all power-supply pins.
12
25
DATAOUT
20
DSN
23
DSP
19
DFO
26
PDOUT
25kΩ
47nF
Figure 4. Using PDOUT for Faster Startup
Control Interface Considerations
When operating the MAX1473 with a +4.5V to +5.5V
supply voltage, the PWRDN and AGCDIS pins may be
driven by a microcontroller with either 3V or 5V interface logic levels. When operating the MAX1473 with a
+3.0V to +3.6V supply, the microcontroller must produce logic levels which conform to the VIH and VIL
specifications in the DC Electrical Characteristics Table
for the MAX1473.
______________________________________________________________________________________
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
MAX1473
Table 2. Component Values for Typical Application Circuit
COMPONENT
VALUE FOR fRF = 433MHz
VALUE FOR fRF = 315MHz
DESCRIPTION
C1
C2
100pF
2.7pF
100pF
4.7pF
5%
±0.1pF
C3
100pF
100pF
5%
C4
100pF
100pF
5%
C5
C6
1500pF
220pF
1500pF
220pF
10%
5%
C7
470pF
470pF
5%
C8
0.47µF
0.47µF
20%
C9
C10
220pF
0.01µF
220pF
0.01µF
10%
20%
C11
0.1µF
0.1µF
20%
C12
15pF
15pF
Depends on XTAL
C13
C14
15pF
0.01µF
15pF
0.01µF
Depends on XTAL
20%
C15
0.01µF
0.01µF
20%
L1
56nH
120nH
5% or better**
L2
L3
15nH
15nH
15nH
27nH
5% or better**
5% or better**
R1
5.1kΩ
5.1kΩ
5%
R2
Open
Open
—
R3
X1(÷64)
Short
6.6128MHz*
Short
4.7547MHz*
—
Crystek or Hong Kong X’tal
X1 (÷32)
13.2256MHz*
9.5094MHz*
Crystek or Hong Kong X’tal
Y1
10.7MHz ceramic filter
10.7MHz ceramic filter
Murata
*Crystal frequencies shown are for ÷64 (VXTALSEL = 0V) and ÷32 (VXTALSEL = VDD).
**Wirewound recommended.
______________________________________________________________________________________
13
MAX1473
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
Typical Application Circuit
IF VDD IS
VDD
VDD3
THEN VDD3 IS
(SEE TABLE)
3.0V TO 3.6V CONNECTED TO VDD
4.5V TO 5.5V
X1
CREATED BY LDO,
AVAILABLE AT AVDD
(PIN 2)
C11
C12
C13
1
RF INPUT
2
C1
L1
3
4
L2
5
6
C14
VDD3
7
L3
C3
8
C2
9
C4
10
C9
11
**
12
13
14
XTAL1
XTAL2
AVDD
PWRDN
LNAIN
PDOUT
MAX1473
LNASRC
DATAOUT
AGND
VDD5
LNAOUT
DSP
AVDD
DFFB
MIXIN1
OPP
MIXIN2
DSN
AGND
DFO
IRSEL
IFIN2
MIXOUT
IFIN1
DGND
XTALSEL
DVDD
AGCDIS
28
TO/FROM µP
POWER DOWN
DATA OUT
27
26
R2
25
C15
24
R3
23
22
21
C7
20
19
18
17
R1
16
15
FROM µP
*
Y1
C5
C6
C8
IF FILTER
C10
IN
OUT
GND
COMPONENT VALUES
IN TABLE 2
** SEE MIXER SECTION
* SEE PHASE-LOCKED LOOP SECTION
Chip Information
PROCESS: CMOS
14
______________________________________________________________________________________
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
LNASRC
4
LNAIN
AVDD
VDD5
AVDD
DVDD
DGND
AGND
3
AGCDIS LNAOUT
15
6
MIXIN1 MIXIN2
8
9
Q
IMAGE
REJECTION
2
24
IFIN1
17
IFIN2
18
0˚
AUTOMATIC
GAIN
CONTROL
LNA
MIXOUT
12
IRSEL
11
IF LIMITING
AMPS
∑
90˚
3.2V REG
I
MAX1473
RSSI
7
14
13
5,10
DIVIDE
BY 64
VCO
PHASE
DETECTOR
LOOP
FILTER
÷1
DATA
FILTER
RDF1
100kΩ
RDF2
100kΩ
÷2
CRYSTAL
DRIVER
16
1
XTALSEL
XTAL1 XTAL2
28
DATA
SLICER
POWER
DOWN
27
25
PWRDN
DATAOUT
20
23
19
DSN DSP DFO
26
21
22
PDOUT
OPP
DFFB
Package Information
For the latest package outline information and land patterns (footprints), go to www.maxim-ic.com/packages. Note that a “+”, “#”, or
“-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status.
PACKAGE CODE
OUTLINE NO.
LAND
PATTERN NO.
28 TSSOP
U28+1
21-0066
90-0171
32 Thin QFN-EP
T3255+3
21-0140
90-0001
PACKAGE TYPE
______________________________________________________________________________________
15
MAX1473
Functional Diagram
MAX1473
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
Revision History
REVISION
NUMBER
REVISION
DATE
4
5/10
Added lead-free parts and exposed pad in Ordering Information and Pin
Description tables
5
1/11
Updated Absolute Maximum Ratings, AC Electrical Characteristics, Pin
Description, Layout Considerations, Typical Application Circuit, Functional
Diagram, and Package Information; added Voltage Regulator section to the
Detailed Description section
6
1/12
Updated DC Electrical and AC Electrical Characteristics tables, replaced TOC 4,
updated Tables 1 and 2 and Figure 1; updated Phase-Locked Loop, Data Filter,
Data Slicer, and Layout Considerations sections
DESCRIPTION
PAGES
CHANGED
1, 8
2, 3, 4, 8, 9, 12,
13, 14
3, 5, 6, 10–13
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in
the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
16 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2012 Maxim Integrated Products
Maxim is a registered trademark of Maxim Integrated Products, Inc.