DA DAC8812 C8 812 www.ti.com SBAS349A – AUGUST 2005 – REVISED DECEMBER 2005 Dual, Serial Input 16-Bit Multiplying Digital-to-Analog Converter FEATURES DESCRIPTION • • • The DAC8812 is a dual, 16-bit, current-output digital-to-analog converter (DAC) designed to operate from a single +2.7 V to +5.5 V supply. • • • • • • • • • • Relative Accuracy: 1 LSB Max Differential Nonlinearity: 1 LSB Max 2-mA Full-Scale Current ±20%, with VREF = ±10 V 0.5 µs Settling Time Midscale or Zero-Scale Reset Separate 4Q Multiplying Reference Inputs Reference Bandwidth: 10 MHz Reference Dynamics: –105 dB THD SPI™-Compatible 3-Wire Interface: 50 MHz Double Buffered Registers Enable Simultaneous Multichannel Change Internal Power On Reset Industry-Standard Pin Configuration The applied external reference input voltage VREF determines the full-scale output current. An internal feedback resistor (RFB) provides temperature tracking for the full-scale output when combined with an external I-to-V precision amplifier. A double-buffered, serial data interface offers high-speed, 3-wire, SPI and microcontroller compatible inputs using serial data in (SDI), clock (CLK), and a chip-select (CS). A common level-sensitive load DAC strobe (LDAC) input allows simultaneous update of all DAC outputs from previously loaded input registers. Additionally, an internal power-on reset forces the output voltage to zero at system turn-on. An MSB pin allows system reset assertion (RS) to force all registers to zero code when MSB = 0, or to half-scale code when MSB = 1. APPLICATIONS • • • Automatic Test Equipment Instrumentation Digitally Controlled Calibration The DAC8812 is available in an TSSOP-16 package. VREFA B D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 A0 A1 SDI RFBA 16 Input Register R DAC A Register R DAC A IOUTA AGNDA RFBB Input Register R DAC B Register R DAC B IOUTB AGNDB CLK CS EN DAC A B Decode DGND Power-On Reset RS MSB LDAC Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. SPI is a trademark of Motorola, Inc. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2005, Texas Instruments Incorporated DAC8812 www.ti.com SBAS349A – AUGUST 2005 – REVISED DECEMBER 2005 This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION (1) PRODUCT MINIMUM RELATIVE ACCURACY (LSB) DIFFERENTIAL NONLINEARITY (LSB) SPECIFIED TEMPERATURE RANGE PACKAGELEAD PACKAGE DESIGNATOR DAC8812C ±1 ±1 –40°C to +85°C TSSOP-16 PW DAC8812B ±2 ±1 –40°C to +85°C TSSOP-16 PW (1) ORDERING NUMBER TRANSPORT MEDIA, QUANTITY DAC8812ICPW Tube, 90 DAC8812ICPWR Tape and Reel, 2500 DAC8812IBPW Tube, 90 DAC8812IBPWR Tape and Reel, 2500 For the most current specifications and package information, see the Package Option Addendum located at the end of this document, or see the TI website at www.ti.com. ABSOLUTE MAXIMUM RATINGS (1) DAC8812 UNIT VDD to GND – 0.3 to +8 V VREF to GND –18 to +18 V Logic inputs and output to GND – 0.3 to +8 V V(IOUT) to GND – 0.3 to VDD +0.3 V AGNDX to DGND –0.3 to +0.3 V ±50 mA (TJmax – TA)/θJA W Thermal resistance, θJA 100 °C/W Maximum junction temperature (TJmax) +150 °C Operating temperature range – 40 to +85 °C Storage temperature range – 65 to +150 °C Input current to any pin except supplies Package power dissipation (1) 2 Stresses above those listed under absolute maximum ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum conditions for extended periods may affect device reliability. DAC8812 www.ti.com SBAS349A – AUGUST 2005 – REVISED DECEMBER 2005 ELECTRICAL CHARACTERISTICS (1) VDD = 2.7 V to 5.5 V, IOUTX = Virtual GND, AGNDX = 0 V, VREFA, B = 10 V, TA = full operating temperature range, unless otherwise noted. DAC8812 PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNIT STATIC PERFORMANCE (2) Resolution Relative accuracy INL Differential nonlinearity DNL Output leakage current IOUTX Full-scale gain error GFSE Full-scale tempco (3) TCVFS Feedback resistor RFBX 16 Bits DAC8812B ±2 LSB DAC8812C ±1 LSB DAC8812 ±1 LSB Data = 0000h, TA = +25°C 10 nA Data = 0000h, TA = TA max 20 nA ±4 mV ±0.75 Data = FFFFh VDD = 5 V 1 ppm/°C 5 kΩ REFERENCE INPUT VREFX range VREFX Input resistance RREFX Input resistance match RREFX Input capacitance (3) CREFX –15 4 Channel-to-channel 5 15 V 6 kΩ 1 % 5 pF ANALOG OUTPUT Output current Output capacitance (3) IOUTX Data = FFFFh COUTX Code-dependent 1.6 2.5 50 mA pF LOGIC INPUTS AND OUTPUT Input low voltage Input high voltage VIL VIH VDD = +2.7 V 0.6 V VDD = +5 V 0.8 V VDD = +2.7 V 2.1 VDD = +5 V 2.4 V V Input leakage current IIL 1 µA Input capacitance (3) CIL 10 pF 0.4 V Logic output low voltage VOL IOL = 1.6 mA Logic output high voltage VOH IOH = 100 µA 4 V INTERFACE TIMING (3), (4) Clock width high tCH 25 ns Clock width low tCL 25 ns CS to Clock setup tCSS 0 ns Clock to CS hold tCSH 25 ns Clock to SDO prop delay Load DAC pulsewidth Data setup Data hold tPD 2 tLDAC 25 20 ns ns tDS 20 ns tDH 20 ns Load setup tLDS 5 ns Load hold tLDH 25 ns (1) (2) (3) (4) Specifications subject to change without notice. All static performance tests (except IOUT) are performed in a closed-loop system using an external precision OPA277 I-to-V converter amplifier. The DAC8812 RFB terminal is tied to the amplifier output. Typical values represent average readings measured at +25°C. These parameters are specified by design and not subject to production testing. All input control signals are specified with tR = tF = 2.5 ns (10% to 90% of 3 V) and timed from a voltage level of 1.5 V. 3 DAC8812 www.ti.com SBAS349A – AUGUST 2005 – REVISED DECEMBER 2005 ELECTRICAL CHARACTERISTICS (continued) VDD = 2.7 V to 5.5 V, IOUTX = Virtual GND, AGNDX = 0 V, VREFA, B = 10 V, TA = full operating temperature range, unless otherwise noted. DAC8812 PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNIT SUPPLY CHARACTERISTICS Power supply range VDD Positive supply current IDD Power dissipation 5.5 V Logic inputs = 0 V, VDD = +4.5 V to +5.5 V 2.7 2 5 µA Logic inputs = 0 V, VDD = +2.7 V to +3.6 V 1 2.5 µA Logic inputs = 0 V 0.0275 mW ∆VDD = ±5% 0.006 % RANGE PDISS Power supply sensitivity PSS AC CHARACTERISTICS (5) To ±0.1% of full-scale, Data = 0000h to FFFFh to 0000h 0.3 To ±0.0015% of full-scale, Data = 0000h to FFFFh to 0000h 0.5 BW –3 dB VREFX = 100 mVRMS, Data = FFFFh, CFB = 3 pF 10 MHz Q VREFX = 10 V, Data = 7FFFh to 8000h to 7FFFh 5 nV/s Feedthrough error VOUTX/VREFX Data = 0000h, VREFX = 100 mVRMS, f = 100 kHz –70 Crosstalk error VOUTA/VREFB Data = 0000h, VREFB = 100 mVRMS, Adjacent channel, f = 100 kHz –100 Output voltage settling time ts Reference multiplying BW DAC glitch impulse Digital feedthrough Q Total harmonic distortion THD Output spot noise voltage (5) CS = 1 and fCLK = 1 MHz µs dB dB 1 VREF = 5 VPP, Data = FFFFh, f = 1 kHz en µs nV/s –105 f = 1 kHz, BW = 1 Hz 12 dB nV/√Hz All ac characteristic tests are performed in a closed-loop system using an THS4011 I-to-V converter amplifier. PARAMETER MEASUREMENT INFORMATION SDI A1 A0 D15 D14 D13 D12 D11 D10 D9 D1 D0 CLK Input REG. LD tCSS CS tds tdh tch tcl tcsh tlds tLDH LDAC tLDAC Figure 1. DAC8812 Timing Diagram 4 DAC8812 www.ti.com SBAS349A – AUGUST 2005 – REVISED DECEMBER 2005 PIN CONFIGURATION DAC8812 (TOP VIEW) RFBA VREFA IOUTA AGNDA AGNDB IOUTB VREFB RFBB 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 CLK LDAC MSB VDD DGND CS RS SDI PIN DESCRIPTION PIN NAME 1 RFBA DESCRIPTION Establish voltage output for DAC A by connecting to external amplifier output. 2 VREFA DAC A Reference voltage input terminal. Establishes DAC A full-scale output voltage. Can be tied to VDD pin. 3 IOUTA DAC A Current output. 4 AGNDA DAC A Analog ground. 5 AGNDB DAC B Analog ground. 6 IOUTB DAC B Current output. 7 VREFB DAC B Reference voltage input terminal. Establishes DAC B full-scale output voltage. Can be tied to VDD pin. 8 RFBB Establish voltage output for DAC B by connecting to external amplifier output. 9 SDI Serial data input; data loads directly into the shift register. 10 RS Reset pin; active low input. Input registers and DAC registers are set to all 0s or midscale. Register data = 0x0000 when MSB = 0. Register data = 0x8000 when MSB = 1 for DAC8812. 11 CS Chip-select; active low input. Disables shift register loading when high. Transfers serial register data to input register when CS goes high. Does not affect LDAC operation. 12 DGND 13 VDD Positive power-supply input. Specified range of operation 2.7 V to 5.5 V. 14 MSB MSB bit sets output to either 0 or midscale during a RESET pulse (RS) or at system power-on. Output equals zero scale when MSB = 0 and midscale when MSB = 1. MSB pin can be permanently tied to ground or VDD. 15 LDAC Load DAC register strobe; level sensitive active low. Transfers all input register data to the DAC registers. Asynchronous active low input. See Table 2 for operation. 16 CLK Digital ground. Clock input. Positive edge clocks data into shift register. 5 DAC8812 www.ti.com SBAS349A – AUGUST 2005 – REVISED DECEMBER 2005 TYPICAL CHARACTERISTICS: VDD = +5 V At TA = +25°C, +VDD = +5 V, unless otherwise noted. Channel A LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 1.0 TA = +25°C 0.8 0.6 0.6 0.4 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -0.8 -1.0 1.0 8192 16384 24576 32768 40960 49152 57344 65535 Code 0 8192 16384 24576 32768 40960 49152 57344 65535 Code Figure 2. Figure 3. LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = -40°C 0.8 TA = -40°C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) 0 -0.2 -0.6 0 0.2 0 -0.2 0.2 0 -0.2 -0.4 -0.4 -0.6 -0.6 -0.8 -0.8 -1.0 -1.0 0 1.0 8192 16384 24576 32768 40960 49152 57344 65535 Code 0 8192 16384 24576 32768 40960 49152 57344 65535 Code Figure 4. Figure 5. LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = +85°C 0.8 TA = +85°C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) 0.2 -0.4 -1.0 0.2 0 -0.2 0.2 0 -0.2 -0.4 -0.4 -0.6 -0.6 -0.8 -0.8 -1.0 -1.0 0 8192 16384 24576 32768 40960 49152 57344 65535 Code Figure 6. 6 TA = +25°C 0.8 DNL (LSB) INL (LSB) DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 0 8192 16384 24576 32768 40960 49152 57344 65535 Code Figure 7. DAC8812 www.ti.com SBAS349A – AUGUST 2005 – REVISED DECEMBER 2005 TYPICAL CHARACTERISTICS: VDD = +5 V (continued) At TA = +25°C, +VDD = +5 V, unless otherwise noted. Channel B LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 1.0 TA = +25°C 0.8 0.6 0.6 0.4 0.4 0.2 0 -0.2 0 -0.2 -0.4 -0.6 -0.6 -0.8 -0.8 -1.0 0 1.0 8192 16384 24576 32768 40960 49152 57344 65535 Code 0 8192 16384 24576 32768 40960 49152 57344 65535 Code Figure 8. Figure 9. LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = -40°C 0.8 TA = -40°C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) 0.2 -0.4 -1.0 0.2 0 -0.2 0.2 0 -0.2 -0.4 -0.4 -0.6 -0.6 -0.8 -0.8 -1.0 -1.0 0 1.0 8192 16384 24576 32768 40960 49152 57344 65535 Code 0 8192 16384 24576 32768 40960 49152 57344 65535 Code Figure 10. Figure 11. LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = +85°C 0.8 TA = +85°C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) TA = +25°C 0.8 DNL (LSB) INL (LSB) DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 0.2 0 -0.2 0.2 0 -0.2 -0.4 -0.4 -0.6 -0.6 -0.8 -0.8 -1.0 -1.0 0 8192 16384 24576 32768 40960 49152 57344 65535 Code Figure 12. 0 8192 16384 24576 32768 40960 49152 57344 65535 Code Figure 13. 7 DAC8812 www.ti.com SBAS349A – AUGUST 2005 – REVISED DECEMBER 2005 TYPICAL CHARACTERISTICS: VDD = +5 V (continued) At TA = +25°C, +VDD = +5 V, unless otherwise noted. SUPPLY CURRENT vs LOGIC INPUT VOLTAGE REFERENCE MULTIPLYING BANDWIDTH 6 0 -6 -12 -18 -24 -30 -36 -42 -48 -54 -60 -66 -72 -78 -84 -90 -96 -102 -108 -114 180 VDD = +5.0V Attenuation (dB) 140 120 100 80 60 40 VDD = +2.7V 20 0 Output Voltage (50mV/div) 0 8 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 10 100 1k 10k 100k 1M Logic Input Voltage (V) Bandwidth (Hz) Figure 14. Figure 15. DAC GLITCH DAC SETTLING TIME Code: 7FFFh to 8000h Output Voltage (5V/div) Supply Current, IDD (mA) 160 10M Voltage Output Settling Trigger Pulse LDAC Pulse Time (0.2ms/div) Time (0.1ms/div) Figure 16. Figure 17. 100M DAC8812 www.ti.com SBAS349A – AUGUST 2005 – REVISED DECEMBER 2005 TYPICAL CHARACTERISTICS: VDD = +2.7 V At TA = +25°C, +VDD = +2.7 V, unless otherwise noted. Channel A LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 1.0 TA = +25°C 0.8 0.6 0.6 0.4 0.4 0.2 0 -0.2 0 -0.2 -0.4 -0.6 -0.6 -0.8 -0.8 -1.0 0 1.0 8192 16384 24576 32768 40960 49152 57344 65535 Code 0 8192 16384 24576 32768 40960 49152 57344 65535 Code Figure 18. Figure 19. LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = -40°C 0.8 TA = -40°C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) 0.2 -0.4 -1.0 0.2 0 -0.2 0.2 0 -0.2 -0.4 -0.4 -0.6 -0.6 -0.8 -0.8 -1.0 -1.0 0 1.0 8192 16384 24576 32768 40960 49152 57344 65535 Code 0 8192 16384 24576 32768 40960 49152 57344 65535 Code Figure 20. Figure 21. LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = +85°C 0.8 TA = +85°C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) TA = +25°C 0.8 DNL (LSB) INL (LSB) DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 0.2 0 -0.2 0.2 0 -0.2 -0.4 -0.4 -0.6 -0.6 -0.8 -0.8 -1.0 -1.0 0 8192 16384 24576 32768 40960 49152 57344 65535 Code Figure 22. 0 8192 16384 24576 32768 40960 49152 57344 65535 Code Figure 23. 9 DAC8812 www.ti.com SBAS349A – AUGUST 2005 – REVISED DECEMBER 2005 TYPICAL CHARACTERISTICS: VDD = +2.7 V (continued) At TA = +25°C, +VDD = +2.7 V, unless otherwise noted. Channel B LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 1.0 TA = +25°C 0.8 0.6 0.6 0.4 0.4 0.2 0 -0.2 -0.6 -0.6 -0.8 -0.8 -1.0 1.0 8192 16384 24576 32768 40960 49152 57344 65535 Code 0 8192 16384 24576 32768 40960 49152 57344 65535 Code Figure 24. Figure 25. LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = -40°C 0.8 TA = -40°C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) 0 -0.2 -0.4 0 0.2 0 -0.2 0.2 0 -0.2 -0.4 -0.4 -0.6 -0.6 -0.8 -0.8 -1.0 -1.0 0 1.0 8192 16384 24576 32768 40960 49152 57344 65535 Code 0 8192 16384 24576 32768 40960 49152 57344 65535 Code Figure 26. Figure 27. LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = +85°C 0.8 TA = +85°C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) 0.2 -0.4 -1.0 0.2 0 -0.2 0.2 0 -0.2 -0.4 -0.4 -0.6 -0.6 -0.8 -0.8 -1.0 -1.0 0 8192 16384 24576 32768 40960 49152 57344 65535 Code Figure 28. 10 TA = +25°C 0.8 DNL (LSB) INL (LSB) DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 0 8192 16384 24576 32768 40960 49152 57344 65535 Code Figure 29. DAC8812 www.ti.com SBAS349A – AUGUST 2005 – REVISED DECEMBER 2005 THEORY OF OPERATION CIRCUIT OPERATION The DAC8812 contains two 16-bit, current-output, digital-to-analog converters (DACs). Each DAC has its own independent multiplying reference input. The DAC8812 uses a 3-wire, SPI-compatible serial data interface, with a configurable asynchronous RS pin for half-scale (MSB = 1) or zero-scale (MSB = 0) preset. In addition, an LDAC strobe enables two channel simultaneous updates for hardware synchronized output voltage changes. Digital-to-Analog Converters The DAC8812 contains two current-steering R-2R ladder DACs. Figure 30 shows a typical equivalent DAC. Each DAC contains a matching feedback resistor for use with an external I-to-V converter amplifier. The RFBX pin is connected to the output of the external amplifier. The IOUTX terminal is connected to the inverting input of the external amplifier. The AGNDX pin should be Kelvin-connected to the load point in the circuit requiring the full 16-bit accuracy. VDD R R R VREFX RFBX 2R 2R 2R R 5 kW S2 S1 IOUTX AGNDX DGND Digital interface connections omitted for clarity. Switches S1 and S2 are closed, VDD must be powered. Figure 30. Typical Equivalent DAC Channel The DAC is designed to operate with both negative or positive reference voltages. The VDD power pin is only used by the logic to drive the DAC switches on and off. Note that a matching switch is used in series with the internal 5 kΩ feedback resistor. If users are attempting to measure the value of RFB, power must be applied to VDD in order to achieve continuity. The DAC output voltage is determined by VREF and the digital data (D) according to Equation 1: V OUT VREF D 65536 (1) Note that the output polarity is opposite of the VREF polarity for dc reference voltages. The DAC is also designed to accommodate ac reference input signals. The DAC8812 accommodates input reference voltages in the range of –15 V to +15 V. The reference voltage inputs exhibit a constant nominal input resistance of 5 kΩ, ±20%. On the other hand, DAC outputs IOUTA and B are code-dependent and produce various output resistances and capacitances. The choice of external amplifier should take into account the variation in impedance generated by the DAC8812 on the amplifiers' inverting input node. The feedback resistance, in parallel with the DAC ladder resistance, dominates output voltage noise. For multiplying mode applications, an external feedback compensation capacitor (CFB) may be needed to provide a critically damped output response for step changes in reference input voltages. 11 DAC8812 www.ti.com SBAS349A – AUGUST 2005 – REVISED DECEMBER 2005 Figure 15 shows the gain vs frequency performance at various attenuation settings using a 3 pF external feedback capacitor connected across the IOUTX and RFBX terminals. In order to maintain good analog performance, power-supply bypassing of 0.01 µF, in parallel with 1 µF, is recommended. Under these conditions, clean power supply with low ripple voltage capability should be used. Switching power supplies is usually not suitable for this application due to the higher ripple voltage and PSS frequency-dependent characteristics. It is best to derive the DAC8812 5-V supply from the system analog supply voltages (do not use the digital 5-V supply); see Figure 31. 15 V 2R 5V + Analog Power Supply R VDD R R R RFBX VREFX 2R 2R 2R R 5 kW 15 V S2 S1 IOUTX VCC VOUT A1 + AGNDX VEE Load DGND DGND Digital interface connections omitted for clarity. Switches S1 and S2 are closed, VDD must be powered. Figure 31. Recommended Kelvin-Sensed Hookup VREF A B CS EN VDD CLK SDI D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 A0 A1 RFBB 16 DAC A Register R Input Register R DAC A AGNDA RFBB DAC B Register R Input Register R DAC B IOUTB AGNDB DAC A B Set MSB Decode Set MSB Poweron Reset DGND MSB LDAC Figure 32. System Level Digital Interfacing 12 IOUTA RS DAC8812 www.ti.com SBAS349A – AUGUST 2005 – REVISED DECEMBER 2005 SERIAL DATA INTERFACE The DAC8812 uses a 3-wire (CS, SDI, CLK) SPI-compatible serial data interface. Serial data of the DAC8812 is clocked into the serial input register in an 18-bit data-word format. MSB bits are loaded first. Table 1 defines the 18 data-word bits for the DAC8812. Data is placed on the SDI pin, and clocked into the register on the positive clock edge of CLK subject to the data setup and data hold time requirements specified in the Interface Timing specifications of the Electrical Characteristics. Data can only be clocked in while the CS chip select pin is active low. For the DAC8812, only the last 18 bits clocked into the serial register are interrogated when the CS pin returns to the logic high state. Since most microcontrollers output serial data in 8-bit bytes, three right-justified data bytes can be written to the DAC8812. Keeping the CS line low between the first, second, and third byte transfers will result in a successful serial register update. Once the data is properly aligned in the shift register, the positive edge of the CS initiates the transfer of new data to the target DAC register, determined by the decoding of address bits A1 and A0. For the DAC8812, Table 1, Table 2, Table 3, and Figure 1 define the characteristics of the software serial interface. Table 1. Serial Input Register Data Format, Data Loaded MSB First (1) Bit B17 (MSB) B16 B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 (LSB) Data A1 A0 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 (1) Only the last 18 bits of data clocked into the serial register (address + data) are inspected when the CS line positive edge returns to logic high. At this point an internally-generated load strobe transfers the serial register data contents (bits D15-D0) to the decoded DAC-input-register address determined by bits A1 and A0. Any extra bits clocked into the DAC8812 shift register are ignored; only the last 18 bits clocked in are used. If double-buffered data is not needed, the LDAC pin can be tied logic low to disable the DAC registers. Table 2. Control Logic Truth Table (1) CS CLK LDAC RS MSB H X H H X No effect Latched Latched L L H H X No effect Latched Latched L ↑+ H H X Shift register data advanced one bit Latched Latched L H H H X No effect Latched Latched ↑+ L H H X No effect Selected DAC updated with current SR contents Latched H X L H X No effect Latched Transparent H X H H X No effect Latched Latched H X ↑+ H X No effect Latched Latched H X H L 0 No effect Latched data = 0000h Latched data = 0000h H X H L H No effect Latched data = 8000h Latched data = 8000h (1) SERIAL SHIFT REGISTER INPUT REGISTER DAC REGISTER ↑+ = Positive logic transition; X = Do not care Table 3. Address Decode A1 A0 0 0 DAC DECODE None 0 1 DAC A 1 0 DAC B 1 1 DAC A and DAC B 13 DAC8812 www.ti.com SBAS349A – AUGUST 2005 – REVISED DECEMBER 2005 Figure 33 shows the equivalent logic interface for the key digital control pins for the DAC8812. To Input Register Address Decoder CS A B EN Shift Register CLK SDI Figure 33. DAC8812 Equivalent Logic Interface Two additional pins RS and MSB provide hardware control over the preset function and DAC register loading. If these functions are not needed, the RS pin can be tied to logic high. The asynchronous input RS pin forces all input and DAC registers to either the zero-code state (MSB = 0), or the half-scale state (MSB = 1). POWER ON RESET When the VDD power supply is turned on, an internal reset strobe forces all the Input and DAC registers to the zero-code state or half-scale, depending on the MSB pin voltage. The VDD power supply should have a smooth positive ramp without drooping, in order to have consistent results, especially in the region of VDD = 1.5 V to 2.3 V. The DAC register data stays at zero or half-scale setting until a valid serial register data load takes place. ESD Protection Circuits All logic-input pins contain back-biased ESD protection zener diodes connected to ground (DGND) and VDD as shown in Figure 34. VDD DIGITAL INPUTS 250 W DGND Figure 34. Equivalent ESD Protection Circuits PCB LAYOUT The DAC8812 is a high-accuracy DAC that can have its performance compromised by grounding and printed circuit board (PCB) lead trace resistance. The 16-bit DAC8812 with a 10-V full-scale range has an LSB value of 153 mV. The ladder and associated reference and analog ground currents for a given channel can be as high as 2 mA. With this 2-mA current level, a series wiring and connector resistance of only 76 mΩ will cause 1 LSB of voltage drop. The preferred PCB layout for the DAC8812 is to have all AGNDX pins connected directly to an analog ground plane at the unit. The noninverting input of each channel I/V converter should also either connect directly to the analog ground plane or have an individual sense trace back to the AGNDX pin connection. The feedback resistor trace to the I/V converter should also be kept short and have low resistance in order to prevent IR drops from contributing to gain error. This attention to wiring ensures the optimal performance of the DAC8812. 14 DAC8812 www.ti.com SBAS349A – AUGUST 2005 – REVISED DECEMBER 2005 APPLICATION INFORMATION The DAC8812, a 2-quadrant multiplying DAC, can be used to generate a unipolar output. The polarity of the full-scale output IOUT is the inverse of the input reference voltage at VREF. Some applications require full 4-quadrant multiplying capabilities or bipolar output swing, as shown in Figure 35. An additional external op amp (A2) is added as a summing amp. In this circuit, the first and second amps (A1 and A2) provide a gain of 2X that widens the output span to 20 V. A 4-quadrant multiplying circuit is implemented by using a 10-V offset of the reference voltage to bias A2. According to the following circuit transfer equation (Equation 2), input data (D) from code 0 to full scale produces output voltages of VOUT = –10 V to VOUT = 10 V. V OUT 32,D768 1 V REF (2) 10 kW 10 kW 10 V 5 kW VOUT OPA277 VREF -10 V < VOUT < +10 V VDD VREFX RFBX One Channel DAC8812 IOUTX OPA277 AGNDX Digital interface connections omitted for clarity. Figure 35. Four-Quadrant Multiplying Application Circuit Cross-Reference The DAC8812 has an industry-standard pinout. Table 4 provides the cross-reference information. Table 4. Cross-Reference PRODUCT INL (LSB) DNL (LSB) SPECIFIED TEMPERATURE RANGE DAC8812ICPW ±1 ±1 DAC8812IBPW ±2 ±1 PACKAGE DESCRIPTION PACKAGE OPTION CROSS-REFERENCE PART NUMBER –40°C to +85°C 16-Lead Thin Shrink Small-Outline Package TSSOP-16 N/A –40°C to +85°C 16-Lead Thin Shrink Small-Outline Package TSSOP-16 AD5545BRU 15 PACKAGE OPTION ADDENDUM www.ti.com 10-Feb-2006 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty DAC8812IBPW ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR DAC8812IBPWG4 ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR DAC8812IBPWR ACTIVE TSSOP PW 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR DAC8812IBPWRG4 ACTIVE TSSOP PW 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR DAC8812IBPWT PREVIEW TSSOP PW 16 250 TBD Call TI DAC8812ICPW ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR DAC8812ICPWG4 ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR DAC8812ICPWR ACTIVE TSSOP PW 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR DAC8812ICPWRG4 ACTIVE TSSOP PW 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR DAC8812ICPWT PREVIEW TSSOP PW 16 250 TBD Lead/Ball Finish Call TI MSL Peak Temp (3) Call TI Call TI (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 MECHANICAL DATA MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0°– 8° A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Mailing Address: Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2006, Texas Instruments Incorporated