Flexible Double Ended Voltage and Current Mode PWM Controllers ISL6740, ISL6741 Features The ISL6740, ISL6741 family of adjustable frequency, low power, pulse width modulating (PWM) voltage mode (ISL6740) and current mode (ISL6741) controllers is designed for a wide range of power conversion applications using half-bridge, full bridge, and push-pull configurations. These controllers provide an extremely flexible oscillator that allows precise control of frequency, duty cycle, and deadtime. • Precision Duty Cycle and Deadtime Control This advanced BiCMOS design features low operating current, adjustable switching frequency up to 1MHz, adjustable softstart, internal and external over-temperature protection, fault annunciation, and a bidirectional SYNC signal that allows the oscillator to be locked to paralleled units or to an external clock for noise sensitive applications. • Bidirectional Synchronization Ordering Information • Adjustable Soft-start PART NUMBER (Notes 2, 3) PART MARKING TEMP. RANGE (°C) PACKAGE PKG. DWG. # -40 to +105 16 Ld SOIC (Pb-free) M16.15 ISL6740IVZ (Note 1) ISL67 40IVZ -40 to +105 16 Ld TSSOP (Pb-free) M16.173 ISL6741IB ISL6741IB -40 to +105 16 Ld SOIC M16.15 ISL6741IBZ 6741IBZ (Note 1) -40 to +105 16 Ld SOIC (Pb-free) M16.15 ISL6741IVZ (Note 1) -40 to +105 16 Ld TSSOP (Pb-free) M16.173 NOTES: 1. Add “-T*” suffix for tape and reel. Please refer to TB347 for details on reel specifications. 2. These Intersil Pb-free plastic packaged products employ special Pbfree material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pbfree requirements of IPC/JEDEC J STD-020. 3. For Moisture Sensitivity Level (MSL), please see device information page for ISL6740, ISL6741. For more information on MSL please see techbrief TB363. December 2, 2011 FN9111.6 ISL674x x= CONTROL MODE 0 Voltage Mode 1 Current Mode 1 • Adjustable Delayed Overcurrent Shutdown and Re-start (ISL6740) • Adjustable Short Circuit Shutdown and Re-start • Adjustable Oscillator Frequency Up to 2MHz • Inhibit Signal • Internal Over-Temperature Protection • System Over-Temperature Protection Using a Thermistor or Sensor • Adjustable Input Undervoltage Lockout ISL6740IBZ 6740IBZ (Note 1) ISL67 41IVZ • 95µA Start-up Current • Fault Signal • Tight Tolerance Voltage Reference Over Line, Load, and Temperature • Pb-Free Available (RoHS Compliant) Applications • Telecom and Datacom Power • Wireless Base Station Power • File Server Power • Industrial Power Systems • DC Transformers and Buss Regulators Pin Configuration ISL6740, ISL6741 (16 LD SOIC, 16 LD TSSOP) TOP VIEW OUTA 1 16 OUTB GND 2 15 VREF SCSET 3 14 VDD CT 4 13 RTD SYNC 5 12 RTC CS 6 11 OTS VERROR 7 UV 8 10 FAULT 9 SS CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas Inc. 2003, 2004, 2007, 2011. All Rights Reserved Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners. Functional Block Diagram ISL6740 VDD SYNC VREF VREF 5.00 V 1% 2 + - FL 100 Q OUTA Q PWM TOGGLE OUTB ENABLE T BG +- 4.5k GND OC S/D SC S/D UV VREF 70µA S Q BI-DIRECTIONAL SYNCHRONIZATION SYNC IN R Q SC LATCH SS LOW EXT. SYNC ON SS IRTC RTC RTD IRTD SCSET SHORT CIRCUIT DETECTION CT SS HI 0.6V 0.4 + -- + - Q 50µs RETRIGGERABLE ONE SHOT FN9111.6 December 2, 2011 OTS SS LOW S Q R Q PWM LATCH RESET DOMINANT PWM COMPARATOR 0.27V R Q SC S/D FAULT VREF OC S/D SS 0.5 + - 4.25V FAULT LATCH SET DOMINANT S Q FL INHIBIT OC DETECT VERROR 0.4 + - Q SS DONE CS 15µA R Q 300k 4.5V SS CLAMP CLK OC LATCH S Q SS DONE + OSCILLATOR VREF UV 4.65V VREF/2 + + BG +- ISL6740, ISL6741 INTERNAL OT SHUTDOWN +130°C TO +150°C INHIBIT/VIN UV 1.00V + INHIBIT - N_SYNC OUT Functional Block Diagram (Continued) ISL6741 SYNC VREF VDD VREF 5.00 V 1% 3 + - FL 100 Q OUTA Q PWM TOGGLE OUTB ENABLE T BG +- 4.5k GND SC S/D UV VREF 70µA SC LATCH S Q ON R Q SS RTC RTD IRTC + OSCILLATOR IRTD 4.5V SS CLAMP CLK SCSET 15µA SS DONE 300k SHORT CIRCUIT DETECTION CT SS DONE SS LOW CS 0.6V 80mV +- + -- + - S Q VERROR 0.2 FAULT SC S/D VREF SS 0.25 OTS R Q PWM LATCH RESET DOMINANT PWM COMPARATOR 0.27V FAULT LATCH SET DOMINANT S Q FL R Q INHIBIT OC DETECT + - VREF UV 4.65V VREF/2 + + BG +- ISL6740, ISL6741 1.00 V N_SYNC OUT INTERNAL OT SHUTDOWN BI-DIRECTIONAL +130°C TO +150°C SYNCHRONIZATION SYNC IN INHIBIT/VIN UV + EXT. SYNC INHIBIT - FN9111.6 December 2, 2011 Typical Application (ISL6740) - 48V Input DC Transformer, 12V @ 8A Output (ISL6740EVAL1) SP1 VIN+ +12V QR1 L1 C11 QH C2 QR3 T1 L3 R8 C9 C13 R10 TP1 4 C1 QR2 C14 QR4 R11 C12 CR2 C3 CR1 C7 U1 HIP2101 VDD LO HB VSS HO LI HS HI C4 R14 R5 TP4 TP2 R6 VREF C10 RT1 C5 OTS OUTA CS CT RTC VREF RTD TP6 UV VDD R3 SCSET R17 ISL6740 OUTB R7 R19 VERROR GND VIN- SYNC FAULT U3 SS C18 TP5 Q5 R13 C15 C17 D1 FN9111.6 December 2, 2011 R18 C6 R12 C16 R15 ISL6740, ISL6741 R1 R9 QL CR3 RTN L2 T2 R2 C8 Typical Application (ISL6740) - 36V to 75V Input, Regulated 12V @ 8A Output (ISL6740EVAL2Z) SP1 VIN+ CR5 L1 QH C11 QR1 T1 L3 C2 +12V R26 QR3 R8 + C13 C8 RTN L2 R10 TP1 C21 C9 CR4 5 C1 T2 CR6 R27 QL R2 C14 CR3 QR2 R11 36V TO 75V R9 QR4 R1 C3 CR1 C7 U1 HIP2101 VDD LO HB VSS HO LI HS HI C4 R14 R5 TP4 TP2 R6 VREF C10 C5 GND R4 R20 R19 CT SCSET RTC UV VREF RTD R3 TP6 CS ISL6740 OUTA VDD R19 VERROR OUTB R17 SYNC OTS VIN- FAULT U3 SS C18 TP5 R7 + 12V RT1 Q5 R23 C22 C20 R25 R13 C15 R21 C19 U2 C17 D1 R18 FN9111.6 December 2, 2011 C6 R12 C16 R15 U4 D2 R24 ISL6740, ISL6741 C12 CR2 Typical Application (ISL6741) - 48V to 5V Push-Pull DC/DC Converter + 5V RTN +48V QR1 R18 R19 R20 T1 + C9 CR1 EL7242 +5V L1 6 C1 CR2 QR2 Q1 U5 RT1 Q2 T3 OUTB R11 SYNC VERROR OUTA CS CT + 5V SCSET VREF RTD R4 OUTA CR4 RTC UV VDD CR3 U3 SS GND OUTB ISL6741 VIN- SYNC R3 OTS R1 FAULT R2 R21 R14 R13 R15 C8 R6 R5 C3 Q3 R7 R8 C4 C5 R16 R10 C7 U2 C6 FN9111.6 December 2, 2011 VR1 U4 R17 C2 R9 ISL6740, ISL6741 R12 ISL6740, ISL6741 Absolute Maximum Ratings (Note 6) Thermal Information Supply Voltage, VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to +20.0V OUTA, OUTB, Signal Pins . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to VREF VREF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .GND - 0.3V to 6.0V Peak GATE Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.5A ESD Classification Human Body Model (Per MIL-STD-883 Method 3015.7) . . . . . . . . 1500V Charged Device Model (Per EOS/ESD DS5.3, 4/14/93). . . . . . . . 1000V Thermal Resistance (Typical) θJA (°C/W) θJC (°C/W) 16 Lead SOIC (Notes 4, 5) . . . . . . . . . . . . . . 74 33 16 Lead TSSOP (Notes 4, 5) . . . . . . . . . . . . 98 30 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . .-55°C to +150°C Maximum Storage Temperature Range . . . . . . . . . . . . . .-65°C to +150°C Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Operating Conditions Temperature Range ISL6740Ix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +105°C ISL6741Ix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +105°C Supply Voltage Range (Typical). . . . . . . . . . . . . . . . . . . . . . . . 9VDC - 16VDC CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 4. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379. 5. For θJC, the “case temp” location is taken at the package top center. 6. All voltages are with respect to GND. Electrical Specifications Recommended operating conditions unless otherwise noted. Refer to “Functional Block Diagram” on page 2 and page 3 and Typical Application Schematics on page 4 to page 6. 9V < VDD < 20 V, RTD = 51.1kΩ, RTC = 10kΩ, CT = 470pF, TA = -40°C to +105°C, Typical values are at TA = +25°C. Boldface limits apply over the operating temperature range, -40°C to +105°C PARAMETER TEST CONDITIONS MIN (Note 7) TYP MAX (Note 7) UNITS SUPPLY VOLTAGE Start-Up Current, IDD VDD < START Threshold - 95 140 µA Operating Current, IDD RLOAD, COUTA,B = 0 - 5.0 8.0 mA COUTA,B = 1nF - 7.0 12.0 mA UVLO START Threshold 6.50 7.25 8.00 V UVLO STOP Threshold 6.00 6.75 7.50 V Hysteresis 0.25 0.50 0.75 V 4.900 5.000 5.050 V - 3 - mV Fault Voltage 4.10 4.55 4.75 V VREF Good Voltage 4.25 4.75 VREF - 0.05 V Hysteresis 75 165 250 mV Operational Current (Source) -20 - - mA 5 - - mA -25 - -100 mA 0.55 0.6 0.65 V CS to OUT Delay - 35 50 ns CS Sink Current - 10 - mA -1.00 - 1.00 µA - 80 - mV REFERENCE VOLTAGE Overall Accuracy IVREF = 0, -20mA Long Term Stability TA = +125°C, 1000 hours Operational Current (Sink) Current Limit CURRENT SENSE Current Limit Threshold VERROR = VREF Input Bias Current CS to PWM Comparator Input Offset (ISL6741) 7 (Note 7) FN9111.6 December 2, 2011 ISL6740, ISL6741 Electrical Specifications Recommended operating conditions unless otherwise noted. Refer to “Functional Block Diagram” on page 2 and page 3 and Typical Application Schematics on page 4 to page 6. 9V < VDD < 20 V, RTD = 51.1kΩ, RTC = 10kΩ, CT = 470pF, TA = -40°C to +105°C, Typical values are at TA = +25°C. Boldface limits apply over the operating temperature range, -40°C to +105°C (Continued) MIN (Note 7) TYP MAX (Note 7) UNITS - 4 - V/V SCSET Input Impedance 1 - - MΩ SC Setpoint Accuracy - 10 - % 400 - - kΩ VERROR < CS Offset (ISL6741) - - 0 % VERROR < CT Valley Voltage (ISL6740) - - 0 % VERROR > 4.75V (Note 9) - 83 - % VERROR to PWM Comparator Input Offset (ISL6741) 0.4 1.0 1.25 V VERROR to PWM Comparator Input Gain (ISL6741) - 0.25 - VERROR to PWM Comparator Input Gain (ISL6740) - 0.4 - V/V CT to PWM Comparator Input Gain (ISL6740) - 0.4 - V/V SS to PWM Comparator Input Gain (ISL6740) - 0.5 - V/V SS to PWM Comparator Input Gain (ISL6741) - 0.2 - V/V 333 351 369 kHz PARAMETER TEST CONDITIONS ACS = ΔVERROR/ΔVCS Gain (ISL6741) PULSE WIDTH MODULATOR VERROR Input Impedance Minimum Duty Cycle Maximum Duty Cycle OSCILLATOR Frequency Accuracy TA = +25°C Frequency Variation with VDD T = +105°C (f20V- - f9V)/f9V - 2 3 % T = -40°C (f20V- - f9V)/f9V - 2 3 % Temperature Stability - 8 - % Charge Current Gain 1.88 2.0 2.12 µA/µA 45 55 65 µA/µA CT Valley Voltage 0.75 0.80 0.85 V CT Peak Voltage 2.70 2.80 2.90 V - 2.000 - V Input High Threshold (VIH), Minimum 4.0 - - V Input Low Threshold (VIL), Maximum - - 0.8 V 4.5 - kΩ Free Running - 1.67 x Free Running Hz Discharge Current Gain RTD, RTC Voltage RLOAD = 0 SYNCHRONIZATION Input Impedance Input Frequency Range High Level Output Voltage (VOH) ILOAD = -1mA - 4.5 - V Low Level Output Voltage (VOL) ILOAD = 10µA - - 100 mV SYNC Output Current VOH > 2.0V -10 - - mA SYNC Output Pulse Duration (Minimum) (Note 8) 250 - 532 ns SYNC Advance SYNC rising edge to GATE falling edge, CGATE = CSYNC = 100pF - 5 - ns -45 -55 -75 µA SOFT-START Charging Current SS = 2V 8 FN9111.6 December 2, 2011 ISL6740, ISL6741 Electrical Specifications Recommended operating conditions unless otherwise noted. Refer to “Functional Block Diagram” on page 2 and page 3 and Typical Application Schematics on page 4 to page 6. 9V < VDD < 20 V, RTD = 51.1kΩ, RTC = 10kΩ, CT = 470pF, TA = -40°C to +105°C, Typical values are at TA = +25°C. Boldface limits apply over the operating temperature range, -40°C to +105°C (Continued) MIN (Note 7) TYP MAX (Note 7) UNITS SS Clamp Voltage 4.35 4.5 4.65 V Sustained Overcurrent Threshold Voltage (ISL6740) Charged Threshold minus: 0.20 0.25 0.30 V PARAMETER TEST CONDITIONS Overcurrent/Short Circuit Discharge Current SS = 2V 13 18 23 µA Fault SS Discharge Current SS = 2V - 10.0 - mA 0.25 0.27 0.33 V Reset Threshold Voltage FAULT Fault High Level Output Voltage (VOH) ILOAD = -10mA 2.85 3.5 - V Fault Low Level Output Voltage (VOL) ILOAD = 10mA - 0.4 0.9 V Fault Rise Time CLOAD = 100pF - 15 - ns Fault Fall Time CLOAD = 100pF - 15 - ns High Level Output Voltage (VOH) VREF - OUTA or OUTB, IOUT = -50mA - 0.5 1.0 V Low Level Output Voltage (VOL) OUTA or OUTB - GND, IOUT = 50mA - 0.5 1.0 V Rise Time CGATE = 1nF, VDD = 15V - 50 100 ns Fall Time CGATE = 1nF, VDD = 15V - 40 80 ns Thermal Shutdown 135 145 155 °C Thermal Shutdown Clear 120 130 140 °C Hysteresis, Internal Protection - 15 - °C Reference, External Protection 2.375 2.50 2.625 V Hysteresis, External Protection 18 25 30 µA 0.97 1.00 1.03 V 7 10 15 µA 4.8 - - V 1 - - MΩ OUTPUT THERMAL PROTECTION SUPPLY UVLO/INHIBIT Input Voltage Low/Inhibit Threshold Hysteresis, Switched Current Amplitude Input High Clamp Voltage Input Impedance NOTES: 7. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design. 8. SYNC pulse width is the greater of this value or the CT discharge time. 9. This is the maximum duty cycle achievable using the specified values of RTC, RTD, and CT. Larger or smaller maximum duty cycles may be obtained using other values for these components. See Equations 2 through 4. 9 FN9111.6 December 2, 2011 ISL6740, ISL6741 Typical Performance Curves 65 CT DISCHARGE CURRENT GAIN NORMALIZED VREF 1.001 1.000 0.999 0.998 0.997 -40 -25 -10 5 20 35 50 65 80 95 110 60 55 50 45 40 0 50 100 150 200 250 300 350 400 450 500 TEMPERATURE (°C) RTD CURRENT (µA) FIGURE 1. REFERENCE VOLTAGE vs TEMPERATURE FIGURE 2. OSCILLATOR CT DISCHARGE CURRENT GAIN 1•106 CT (pF) = 1000 680 470 1•103 330 220 100 FREQUENCY (Hz) DEADTIME - TD (ns) 1•104 100 10 10 20 30 40 50 60 70 80 90 100 RTD (kΩ) 1•105 RTD = 10k CT (pF) = 100 220 330 470 1•104 10 20 30 680 1000 40 50 60 70 80 90 100 RTC (kΩ) FIGURE 3. DEADTIME (TD) vs CAPACITANCE FIGURE 4. CAPACITANCE vs FREQUENCY Pin Descriptions VDD - VDD is the power connection for the IC. To optimize noise immunity, bypass VDD to GND with a ceramic capacitor as close to the VDD and GND pins as possible. The total supply current, IDD, will be dependent on the load applied to outputs OUTA and OUTB. Total IDD current is the sum of the quiescent current and the average output current. Knowing the operating frequency, fSW, and the output loading capacitance charge, Q, per output, the average output current can be calculated from: I OUT = 2 • Q • f SW A (EQ. 1) SYNC - A bidirectional synchronization signal used to coordinate the switching frequency of multiple units. Synchronization may be achieved by connecting the SYNC signal of each unit together or by using an external master clock signal. The oscillator timing capacitor, CT, is always required regardless of the synchronization method used. The paralleled unit with the highest oscillator frequency assumes control. Selfsynchronization is not recommended for oscillator frequencies above 900kHz. For higher switching frequencies, an external 10 clock with a pulse width less than one-half of the oscillator period must be used. RTC - This is the oscillator timing capacitor charge current control pin. A resistor is connected between this pin and GND. The current flowing through the resistor determines the magnitude of the charge current. The charge current is nominally twice this current. The PWM maximum ON time is determined by the timing capacitor charge duration. RTD - This is the oscillator timing capacitor discharge current control pin. A resistor is connected between this pin and GND. The current flowing through the resistor determines the magnitude of the discharge current. The discharge current is nominally 50x this current. The PWM deadtime is determined by the timing capacitor discharge duration. CT - The oscillator timing capacitor is connected between this pin and GND. VERROR - The inverting input of the PWM comparator. The error voltage is applied to this pin to control the duty cycle. Increasing the signal level increases the duty cycle. The node may be driven with an external error amplifier or opto-coupler. FN9111.6 December 2, 2011 ISL6740, ISL6741 The ISL6740, ISL6741 features a built-in soft-start. Soft-start is implemented as a clamp on the error voltage input. current limit characteristic of peak current mode control limits the output current to acceptable levels. OTS - The non-inverting input to the over-temperature shutdown comparator. The signal input at this pin is compared to an internal threshold of VREF/2. If the voltage at this pin exceeds the threshold, the Fault signal is asserted and the outputs are disabled until the condition clears. There is a nominal 25μA switched current source used for hysteresis. The amount of hysteresis is adjustable by varying the source impedance of the signal into this pin. GND - Reference and power ground for all functions on this device. Due to high peak currents and high frequency operation, a low impedance layout is necessary. Ground planes and short traces are highly recommended. OTS may be used to monitor parameters other than temperature, such as voltage. Any signal for which a high out-of-bounds monitor is desired may utilize the OTS comparator. FAULT - The Fault signal is asserted high whenever the outputs, OUTA and OUTB, are disabled. This occurs during an overtemperature fault, an input UV fault, a VREF UV fault, or during an overcurrent (ISL6740) or short circuit shutdown fault. Fault can be used to disable synchronous rectifiers whenever the outputs are disabled. Fault is a three-state output and is high impedance during the soft-start cycle. Adding a pull-up resistor to VREF or a pull-down resistor to ground determines the state of Fault during soft-start. This feature allows the designer to use the Fault signal to enable or disable output synchronous rectifiers during soft-start. UV - Undervoltage monitor input pin. A resistor divider between the input source voltage and GND sets the undervoltage lock out threshold. The signal is compared to an internal 1.00V reference to detect an undervoltage or inhibit condition. CS - This is the input to the current sense comparator(s). The IC has the PWM comparator for peak current mode control (ISL6741) and an overcurrent protection comparator. The overcurrent comparator threshold is set at 0.600V nominal. The CS pin is shorted to GND at the end of each switching cycle. Depending on the current sensing source impedance, a series input resistor may be required due to the delay between the internal clock and the external power switch. This delay may allow an overlap such that the CS signal may be discharged while the current signal is still active. If the current sense source is low impedance, it will cause increased power dissipation. ISL6740 - Exceeding the overcurrent threshold will start a delayed shutdown sequence. Once an overcurrent condition is detected, the soft-start charge current source is disabled. The soft-start capacitor begins discharging through a 25μA current source, and if it discharges to less than 4.25V (Sustained Overcurrent Threshold), a shutdown condition occurs and the OUTA and OUTB outputs are forced low. When the soft-start voltage reaches 0.27V (Reset Threshold) a soft-start cycle begins. An overcurrent condition must be absent for 50μs before the delayed shutdown control resets. If the overcurrent condition ceases, and an additional 50μs period elapses before the shutdown threshold is reached, no shutdown occurs. The SS charging current is re-enabled and the soft-start voltage is allowed to recover. ISL6741 - The ISL6741 current mode controller does not shutdown due to an overcurrent condition. The pulse-by-pulse 11 OUTA and OUTB - Alternate half cycle output stages. Each output is capable of 0.5A peak currents for driving logic level power MOSFETs or MOSFET drivers. Each output provides very low impedance to overshoot and undershoot. VREF - The 5.00V reference voltage output. +1%/-2% tolerance over line, load and operating temperature. Bypass to GND with a 0.047μF to 2.2μF ceramic capacitor. Capacitors outside of this range may cause oscillation. SS - Connect the soft-start timing capacitor between this pin and GND to control the duration of soft-start. The value of the capacitor determines the rate of increase of the duty cycle during start up, controls the overcurrent shutdown delay (ISL6740), and the overcurrent and short circuit hiccup restart period. SCSET - Sets the duty cycle threshold that corresponds to a short circuit condition. A resistive divider between RTC and GND or RTD and GND, or a voltage between 0V and 2V may be used to adjust the SCSET threshold. If using a resistor divider from either RTC or RTD, the impedance to GND affects the oscillator timing and should be considered when determining the oscillator timing components. Connecting SCSET to GND disables short circuit shutdown and hiccup. Functional Description Features The ISL6740, ISL6741 PWMs are an excellent choice for low cost bridge and push-pull topologies for applications requiring accurate duty cycle and deadtime control. With its many protection and control features, a highly flexible design with minimal external components is possible. Among its many features are current mode control (ISL6741), adjustable softstart, overcurrent protection, thermal protection, bidirectional synchronization, fault indication, and adjustable frequency. Oscillator The ISL6740, ISL6741 have an oscillator with a programmable frequency range to 2MHz, which can be programmed with two resistors and capacitor. The use of three timing elements, RTC, RTD, and CT allow great flexibility and precision when setting the oscillator frequency. The switching period may be considered the sum of the timing capacitor charge and discharge durations. The charge duration is determined by RTC and CT. The discharge duration is determined by RTD and CT. t C ≈ 0.5 • R TC • C T t D ≈ 0.02 • R TD • C T 1 t SW = t C + t D = ----------F SW (EQ. 2) S (EQ. 3) S S (EQ. 4) FN9111.6 December 2, 2011 ISL6740, ISL6741 where tC and tD are the charge and discharge times, respectively, tSW is the oscillator free running period, and f is the oscillator frequency. One output switching cycle requires two oscillator cycles. The actual times will be slightly longer than calculated due to internal propagation delays of approximately 10ns/transition. This delay ads directly to the switching duration, but also causes overshoot of the timing capacitor peak and valley voltage thresholds, effectively increasing the peak-to-peak voltage on the timing capacitor. Additionally, if very low charge and discharge currents are used, there will be increased error due to the input impedance at the CT pin. The maximum duty cycle, D, and percent deadtime, DT, can be calculated from: tC D = ---------t SW (EQ. 5) DT = 1 – D (EQ. 6) Implementing Synchronization The oscillator can be synchronized to an external clock applied to the SYNC pin or by connecting the SYNC pins of multiple ICs together. If an external master clock signal is used, the free running frequency of the oscillator should be ~10% slower than the desired synchronous frequency. The external master clock signal should have a pulse width greater than 20ns. The SYNC circuitry will not respond to an external signal during the first 60% of the oscillator switching cycle. Self-synchronization is not recommended for oscillator frequencies above 900 kHz. For higher switching frequencies, an external clock with a pulse width less than one-half of the oscillator period must be used. The SYNC input is edge triggered and its duration does not affect oscillator operation. However, the deadtime is affected by the SYNC frequency. A higher frequency signal applied to the SYNC input will shorten the deadtime. The shortened deadtime is the result of the timing capacitor charge cycle being prematurely terminated by the external SYNC pulse. Consequently, the timing capacitor is not fully charged when the discharge cycle begins. This effect is only a concern when an external master clock is used, or if units with different operating frequencies are paralleled. recovery from a Fault condition or overcurrent/short circuit shutdown. The soft-start voltage is clamped to 4.5V. The Fault signal output is high impedance during the soft-start cycle. A pull-up resistor to VREF or a pull-down resistor to ground should be added to achieve the desired state of Fault during softstart. Gate Drive The ISL6740, ISL6741 are capable of sourcing and sinking 0.5A peak current, but are primarily intended to be used in conjunction with a MOSFET driver due to the 5V drive level. To limit the peak current through the IC, an external resistor may be placed between the totem-pole output of the IC (OUTA or OUTB pin) and the gate of the MOSFET. This small series resistor also damps any oscillations caused by the resonant tank of the parasitic inductances in the traces of the board and the FET’s input capacitance. Undervoltage Monitor and Inhibit The UV input is used for input source undervoltage lockout and inhibit functions. If the node voltage falls below 1.00V a UV shutdown fault occurs. This may be caused by low source voltage or by intentional grounding of the pin to disable the outputs. There is a nominal 10μA switched current source used to create hysteresis. The current source is active only during an UV/Inhibit fault; otherwise, it is inactive and does not affect the node voltage. The magnitude of the hysteresis is a function of the external resistor divider impedance. If the resistor divider impedance results in too little hysteresis, a series resistor between the UV pin and the divider may be used to increase the hysteresis. A soft-start cycle begins when the UV/Inhibit fault clears. The voltage hysteresis created by the switched current source and the external impedance is generally small due to the large resistor divider ratio required to scale the input voltage down to the UV threshold level. A small capacitor placed between the UV input and ground may be required to filter noise out. VIN R1 Soft-start Operation 1.00V The ISL6740, ISL6741 feature a soft-start using an external capacitor in conjunction with an internal current source. soft-start reduces stresses and surge currents during start up. Upon start up, the soft-start circuitry clamps the error voltage input (VERROR pin) indirectly to a value equal to the soft-start voltage. The soft-start clamp does not actually clamp the error voltage input as is done in many implementations. Rather the PWM comparator has two inverting inputs such that the lower voltage is in control. The output pulse width increases as the soft-start capacitor voltage increases. This has the effect of increasing the duty cycle from zero to the regulation pulse width during the soft-start period. When the soft-start voltage exceeds the error voltage, soft-start is completed. soft-start occurs during start-up, after 12 + - R3 10μA R2 ON FIGURE 5. UV HYSTERESIS As VIN decreases to a UV condition, the threshold level is: R1 + R2 V IN ( DOWN ) = ---------------------R2 V (EQ. 7) FN9111.6 December 2, 2011 ISL6740, ISL6741 The hysteresis voltage, ΔV, is: ΔV = 10 –5 R1 + R2 • 〈 R1 + R3 • ⎛ ----------------------⎞ 〉 ⎝ R2 ⎠ V (EQ. 8) Setting R3 equal to zero results in the minimum hysteresis, and yields: ΔV = 10 –5 • R1 V (EQ. 9) As VIN increases from a UV condition, the threshold level is: V IN ( UP ) = V IN ( DOWN ) + ΔV V (EQ. 10) Overcurrent Operation ISL6740 - Overcurrent delayed shutdown is enabled once the soft-start cycle is complete. If an overcurrent condition is detected, the soft-start charging current source is disabled and the soft-start capacitor is allowed to discharge through a 15μA source. At the same time a 50μs re-triggerable one-shot timer is activated. It remains active for 50μs after the overcurrent condition ceases. If the soft-start capacitor discharges by more then 0.25V to 4.25V, the output is disabled and the Fault signal asserted. This state continues until the soft-start voltage reaches 270mV, at which time a new soft-start cycle is initiated. If the overcurrent condition stops at least 50μs prior to the soft-start voltage reaching 4.25V, the soft-start charging currents revert to normal operation and the soft-start voltage is allowed to recover. sets a threshold that is compared to the voltage on the timing capacitor, CT. The resistor divider percentage corresponds to the fraction of the maximum duty cycle below which a short circuit may exist. If the timing capacitor voltage fails to exceed the threshold before an overcurrent pulse is detected, a short circuit condition exists. A shutdown and soft-start cycle will begin if 8 short circuit events occur within 32 oscillator cycles. Connecting SCSET to GND disables this feature. Since the current sourced from both RTC and RTD determine the charge and discharge currents for the timing capacitor, the effect of the SCSET divider must be included in the timing calculations. Typically the resistor between RTC and GND is formed by two series resistors with the center node connected to SCSET. Alternatively, SCSET may be set using a voltage between 0V and 2V. This voltage divided by 2 determines the percentage of the maximum duty cycle that corresponds to a short circuit when current limit is active. For example, if the maximum duty cycle is 95% and 1V is applied to SCSET, then the short circuit duty cycle is 50% of 95% or 47.5%. Fault Conditions A fault condition occurs if VREF falls below 4.65V, the UV input falls below 1.00V, the thermal protection is triggered, or if OTS faults. When a fault is detected, OUTA and OUTB outputs are disabled, the Fault signal is asserted, and the soft-start capacitor is quickly discharged. When the fault condition clears and the soft-start voltage is below the reset threshold, a soft-start cycle begins. The Fault signal is high impedance during the soft-start cycle. The duration of the OC shutdown period can be increased by adding a resistor between VREF and SS. The value of the resistor must be large enough so that the minimum specified SS discharge current is not exceeded. Using a 422kΩ resistor, for example, will result in a small current being injected into SS, effectively reducing the discharge current. This will increase the OFF time by about 60%, nominally. The external pull-up resistor will also decrease the SS duration, so its effect should be considered when selecting the value of the SS capacitor. An overcurrent condition that results in shutdown (ISL6740), or a short circuit shutdown also cause assertion of the Fault signal. The difference between a current fault and the faults described earlier is that the soft-start capacitor is not quickly discharged. The initiation of a new soft-start cycle is delayed while the softstart capacitor is discharged at a 15μA rate. This keeps the average output current to a minimum. Latching OC shutdown is also possible by using a lower valued resistor between VREF and SS. If the SS node is not allowed to discharge below the SS reset threshold, the IC will not recover from an overcurrent fault. The value of the resistor must be low enough so that the maximum specified discharge current is not sufficient to pull SS below 0.33V. A 200kΩ resistor, for example, prevents SS from discharging below ~0.4V. Again, the external pull-up resistor will decrease the SS duration, so its effect should be considered when selecting the value of the SS capacitor. Two methods of over-temperature protection are provided. The first method is an on board temperature sensor that protects the device should the junction temperature exceed 145°C. There is approximately 15°C of hysteresis. ISL6741 - Overcurrent results in pulse-by-pulse duty cycle reduction as occurs in any peak current mode controller. This results in a well controlled decrease in output voltage with increasing current beyond the overcurrent threshold. An overcurrent condition in the ISL6741 will not cause a shutdown. Thermal Protection The second method uses an internal comparator with a 2.5V reference (VREF/2). The non-inverting input to the comparator is accessible through the OTS pin. A thermistor or thermal sensor located at or near the area of interest may be connected to this input. There is a nominal 25μA switched current source used to create hysteresis. The current source is active only during an OT fault; otherwise, it is inactive and does not affect the node voltage. The magnitude of the hysteresis is a function of the external resistor divider impedance. Either a positive temperature coefficient (PTC) or a negative temperature Short Circuit Operation A short circuit condition is defined as the simultaneous occurrence of current limit and a reduced duty cycle. The degree of reduced duty cycle is user adjustable using the SCSET input. A resistor divider between either RTD or RTC and GND to RCSET 13 FN9111.6 December 2, 2011 ISL6740, ISL6741 coefficient (NTC) thermistor may be used. If a NTC is desired, position R1 may be substituted. VREF VREF ON Circuit Element Descriptions R1 The converter design may be broken down into the following functional blocks: 25μA VREF/2 R3 The input voltage range is 48 ±10%VDC. The output is a nominal 12V when the input voltage is at 48V. Since this is an unregulated topology, the output voltage will vary proportionately with input voltage. The load regulation is a function of resistance between the source and the converter output. The output is rated at 8A. + - Input Filtering: L1, C1, R1 R2 Half-Bridge Capacitors: C2, C3 Isolation Transformer: T1 Primary Snubber: C13, R10 Start Bias Regulator: CR3, R2, R7, C6, Q5, D1 FIGURE 6. OTS HYSTERESIS Supply Bypass Components: R3, C15, C4, C5 If a PTC is desired, then position R2 may be substituted. The threshold with increasing temperature is set by making the fixed resistance equal in value to the thermistor resistance at the desired trip temperature. V TH↑ = 2.5V and R1 = R2 (HOT) 5 Ω (EQ. 11) If the hysteresis resistor, R3, is not desired, the value of the thermistor resistance at the reset temperature can be determined from: 2.5 • R2 R1 = ----------------------------------------–5 2.5 – 10 • R2 Ω 2.5 • R1 R2 = ----------------------------------------–5 2.5 + 10 • R1 Ω Current Sense Network: T2, CR1, CR2, R5, R6, R11, C10, C14 Control Circuit: U3, RT1, R14, R19, R13, R15, R17, R18, C16, C18, C17 Output Rectification and Filtering: QR1, QR2, QR3, QR4, L2, C9, C8 To determine the value of the hysteresis resistor, R3, select the value of thermistor resistance that corresponds to the desired reset temperature. 10 • ( R1 – R2 ) – R1 • R2 R3 = ---------------------------------------------------------------------R1 + R2 Main MOSFET Power Switch: QH, QL ( NTC ) (EQ. 12) Secondary Snubber: R8, R9, C11, C12 FET Driver: U1 ZVS Resonant Delay (Optional): L3, C7 Design Criteria The following design requirements were selected: Switching Frequency, Fsw: 235kHz VIN: 48 ±10%V VOUT: 12V (nominal) @ IOUT = 8A ( PTC ) (EQ. 13) POUT: 100W Efficiency: 95% The OTS comparator may also be used to monitor signals other than suggested above. It may also be used to monitor any voltage signal for which an excess requires a response as described above. Input or output voltage monitoring are examples of this. Ground Plane Requirements Careful layout is essential for satisfactory operation of the device. A good ground plane must be employed. VDD should be bypassed directly to GND with good high frequency capacitance. Ripple: 1% Transformer Design The design of a transformer for a half-bridge application is a straight forward affair, although iterative. It is a process of many compromises, and even experienced designers will produce different designs when presented with identical requirements. The iterative design process is not presented here for clarity. Typical Application The Typical Application Schematic features the ISL6740 in an unregulated half-bridge DC/DC converter configuration, often referred to as a DC Transformer or Bus Regulator. The ISL6740EVAL1 demonstration unit implements this design and is available for evaluation. 14 FN9111.6 December 2, 2011 ISL6740, ISL6741 The abbreviated design process follows: Ae = 0.62cm2 or 6.2e -5m2 • Select a core geometry suitable for the application. Constraints of height, footprint, mounting preference, and operating environment will affect the choice. Using Faraday’s Law, V = N dΦ/dt, the number of primary turns can be determined once the maximum flux density is set. An acceptable Bmax is ultimately determined by the allowable power dissipation in the ferrite material and is influenced by the lossiness of the core, core geometry, operating ambient temperature, and air flow. The TDK datasheet for PC44 material indicates a core loss factor of ~400mW/cm3 with a ±2000 gauss 100kHz sinusoidal excitation. The application uses a 235kHz square wave excitation, so no direct comparison between the application and the data can be made. Interpolation of the data is required. The core volume is approximately 1.6cm3, so the estimated core loss is • Determine the turns ratio. • Select suitable core material(s). • Select maximum flux density desired for operation. • Select core size. Core size will be dictated by the capability of the core structure to store the required energy, the number of turns that have to be wound, and the wire gauge needed. Often the window area (the space used for the windings) and power loss determine the final core size. • Determine maximum desired flux density. Depending on the frequency of operation, the core material selected, and the operating environment, the allowed flux density must be determined. The decision of what flux density to allow is often difficult to determine initially. Usually the highest flux density that produces an acceptable design is used, but often the winding geometry dictates a larger core than is indicated based on flux density alone. • Determine the number of primary turns. f act 3 mW 200kHz P loss ≈ ----------- • cm • --------------- = 0.4 • 1.6 • --------------------- = 1.28 3 f meas 100kHz cm W (EQ. 15) 1.28W of dissipation is significant for a core of this size. Reducing the flux density to 1200 gauss will reduce the dissipation by about the same percentage, or 40%. Ultimately, evaluation of the transformer’s performance in the application will determine what is acceptable. From Faraday’s Law and using 1200 gauss peak flux density (ΔB = 2400 gauss or 0.24 tesla) • Select the wire gauge for each winding. • Determine winding order and insulation requirements. –6 V IN • T ON 53 • 2 • 10 N = ----------------------------- = ------------------------------------------------------ = 3.56 –5 2 • A e • ΔB 2 • 6.2 • 10 • 0.24 • Verify the design. nSR (EQ. 16) Rounding up yields 4 turns for the primary winding. The peak flux density using 4 turns is ~1100 gauss. From Equation 1, the number of secondary turns is 2. nS nP nS The volts/turn for this design ranges from 5.4V at VIN = 43V to 6.6V at VIN = 53V. Therefore, the synchronous rectifier (SR) windings may be set at 1 turn each with proper FET selection. Selecting 2 turns for the synchronous rectifier windings would also be acceptable, but the gate drive losses would increase. nSR FIGURE 7. TRANSFORMER SCHEMATIC For this application we have selected a planar structure to achieve a low profile design. A PQ style core was selected because of its round center leg cross section, but there are many suitable core styles available. Since the converter is operating open loop at nearly 100% duty cycle, the turns ratio, N, is simply the ratio of the input voltage to the output voltage divided by 2. V IN 48 N = ---------------------- = ---------------- = 2 V OUT • 2 12 • 2 turns (EQ. 14) The factor of 2 divisor is due to the half-bridge topology. Only half of the input voltage is applied to the primary of the transformer. A PC44HPQ20/6 “E-Core” plus a PC44PQ20/3 “I-Core” from TDK were selected for the transformer core. The ferrite material is PC44. The next step is to determine the equivalent wire gauge for the planar structure. Since each secondary winding conducts for only 50% of the period, the RMS current is I RMS = I OUT • D = 10 • 0.5 = 7.07 A (EQ. 17) where D is the duty cycle. Since an FR-4 PWB planar winding structure was selected, the width of the copper traces is limited by the window area width, and the number of layers is limited by the window area height. The PQ core selected has a usable window area width of 0.165 inches. Allowing one turn per layer and 0.020 inches clearance at the edges allows a maximum trace width of 0.125 inches. Using 100 circular mils(c.m.)/A as a guideline for current density, and from Equation 17, 707c.m. are required for each of the secondary windings (a circular mil is the area of a circle 0.001 inches in diameter). Converting c.m. to The core parameter of concern for flux density is the effective core cross sectional area, Ae. For the PQ core pieces selected: 15 FN9111.6 December 2, 2011 ISL6740, ISL6741 square mils yields 555mils2 (0.785 sq. mils/c.m.). Dividing by the trace width results in a copper thickness of 4.44 mils (0.112mm). Using 1.3 mils/oz. of copper requires a copper weight of 3.4oz. For reasons of cost, 3oz. copper was selected. between the two secondary windings. The winding layout appears below. One layer of each secondary winding also contains the synchronous rectifier winding. For this layer the secondary trace width is reduced by 0.025 inches to 0.100 inches(0.015 inches for the SR winding trace width and 0.010 inches spacing between the SR winding and the secondary winding). The choice of copper weight may be validated by calculating the DC copper losses of the secondary winding as follows. Ignoring the terminal and lead-in resistance, the resistance of each layer of the secondary may be approximated using Equation 18. 2πρ R = -----------------------⎛ r 2⎞ t • ln ⎜ -----⎟ ⎝ r 1⎠ FIGURE 7A. TOP LAYER: 1 TURN SECONDARY AND SR WINDINGS Ω (EQ. 18) where R = Winding resistance ρ = Resistivity of copper = 669e-9Ω-inches at 20°C t = Thickness of the copper (3 oz.) = 3.9e-3 inches r2 = Outside radius of the copper trace = 0.324 or 0.299 inches r1 = Inside radius of the copper trace = 0.199 inches The winding without the SR winding on the same layer has a DC resistance 2.21mΩ. The winding that shares the layer with the SR winding has a DC resistance of 2.65mΩ. With the secondary configured as a 4 turn center tapped winding (2 turns each side of the tap), the total DC power loss for the secondary at +20°C is 486mW. FIGURE 7B. INT. LAYER 1: 1 TURN SECONDARY WINDING The primary windings have an RMS current of approximately 5A (IOUT x NS/NP at ~ 100% duty cycle). The primary is configured as 2 layers, 2 turns per layer to minimize the winding stack height. Allowing 0.020 inches edge clearance and 0.010 inches between turns yields a trace width of 0.0575 inches. Ignoring the terminal and lead-in resistance, and using Equation 18, the inner trace has a resistance of 4.25mΩ, and the outer trace has a resistance of 5.52mΩ. The resistance of the primary then is 19.5mΩ at +20°C. The total DC power loss for the secondary at +20°C is 489mW. Improved efficiency and thermal performance could be achieved by selecting heavier copper weight for the windings. Evaluation in the application will determine its need. FIGURE 7C. INT. LAYER 2: 2 TURNS PRIMARY WINDING The order and geometry of the windings affects the AC resistance, winding capacitance, and leakage inductance of the finished transformer. To mitigate these effects, interleaving the windings is necessary. The primary winding is sandwiched FIGURE 7D. INT. LAYER 3: 2 TURNS PRIMARY WINDING 16 FN9111.6 December 2, 2011 ISL6740, ISL6741 transition voltage amplitude. If the leakage inductance energy is too low, ZVS operation is not possible and near or partial ZVS operation occurs. As the leakage energy increases, the voltage amplitude increases until it is clamped by the FET body diode to ground or VIN, depending on which FET conducts. When the leakage energy exceeds the minimum required for ZVS operation, the voltage is clamped until the energy is transferred. This behavior increases the time window for ZVS operation. This behavior is not without consequences, however. The transition time and the period of time during which the voltage is clamped reduces the effective duty cycle. FIGURE 7E. INT. LAYER 4: 1 TURN SECONDARY WINDING The gate charge affects the switching speed of the FETs. Higher gate charge translates into higher drive requirements and/or slower switching speeds. The energy required to drive the gates is dissipated as heat. The maximum input voltage, VIN, plus transient voltage, determines the voltage rating required. With a maximum input voltage of 53V for this application, and if we allow a 10% adder for transients, a voltage rating of 60V or higher will suffice. The RMS current through the each primary side FET can be determined from Equation 17, substituting 5A of primary current for IOUT. The result is 3.5A RMS. Fairchild FDS3672 FETs, rated at 100V and 7.5A (rDS(ON) = 22mΩ), were selected for the halfbridge switches. FIGURE 7F. BOTTOM LAYER: 1 TURN SECONDARY AND SR WINDINGS ∅0.689 ∅0.358 0.807 0.639 0.403 The synchronous rectifier FETs must withstand approximately one half of the input voltage assuming no switching transients are present. This suggests a device capable of withstanding at least 30V is required. Empirical testing in the circuit revealed switching transients of 20V were present across the device indicating a rating of at least 60V is required. The RMS current rating of 7.07A for each SR FET requires a low rDS(ON) to minimize conduction losses, which is difficult to find in a 60V device. It was decided to use two devices in parallel to simplify the thermal design. Two Fairchild FDS5670 devices are used in parallel for a total of four SR FETs. The FDS5670 is rated at 60V and 10A (rDS(ON) = 14mΩ). Oscillator Component Selection 0.169 0.000 0.000 0.184 0.479 0.774 1.054 FIGURE 7G. PWB DIMENSIONS MOSFET Selection The criteria for selection of the primary side half-bridge FETs and the secondary side synchronous rectifier FETs is largely based on the current and voltage rating of the device. However, the FET drain-source capacitance and gate charge cannot be ignored. The zero voltage switch (ZVS) transition timing is dependent on the transformer’s leakage inductance and the capacitance at the node between the upper FET source and the lower FET drain. The node capacitance is comprised of the drain-source capacitance of the FETs and the transformer parasitic capacitance. The leakage inductance and capacitance form an LC resonant tank circuit which determines the duration of the transition. The amount of energy stored in the LC tank circuit determines the 17 The desired operating frequency of 235kHz for the converter was established in “Design Criteria” on page 14. The oscillator frequency operates at twice the frequency of the converter because two clock cycles are required for a complete converter period. During each oscillator cycle the timing capacitor, CT, must be charged and discharged. Determining the required discharge time to achieve zero voltage switching (ZVS) is the critical design goal in selecting the timing components. The discharge time sets the deadtime between the two outputs, and is the same as ZVS transition time. Once the discharge time is determined, the remainder of the period becomes the charge time. The ZVS transition duration is determined by the transformer’s primary leakage inductance, Llk, by the FET Coss, by the transformer’s parasitic winding capacitance, and by any other parasitic elements on the node. The parameters may be FN9111.6 December 2, 2011 ISL6740, ISL6741 determined by measurement, calculation, estimate, or by some combination of these methods. π L lk • ( 2C oss + C xfrmr ) t zvs ≈ -----------------------------------------------------------------2 (EQ. 19) S Device output capacitance, Coss, is non-linear with applied voltage. To find the equivalent discrete capacitance, Cfet, a charge model is used. Using a known current source, the time required to charge the MOSFET drain to the desired operating voltage is determined and the equivalent capacitance is calculated. Ichg • t Cfet = ------------------V (EQ. 20) F Once the estimated transition time is determined, it must be verified directly in the application. The transformer leakage inductance was measured at 125nH and the combined capacitance was estimated at 2000pF. Calculations indicate a transition period of ~ 25ns. Verification of the performance yielded a value of tD closer to 45ns. The remainder of the switching half-period is the charge time, tC, and can be found from –9 1 1 = 2.08 t C = --------------- – t D = ----------------------------------- – 45 • 10 3 2 • FS 2 • 235 • 10 μs (EQ. 21) where FS is the converter switching frequency. Using Figure 4, the capacitor value appropriate to the desired oscillator operating frequency of 470kHz can be selected. A CT value of 100pF, 220pF, or 330pF is appropriate for this frequency. A value of 220pF was selected. To obtain the proper value for RTD, Equation 3 is used. Since there is a 10ns propagation delay in the oscillator circuit, it must be included in the calculation. The value of RTD selected is 8.06kΩ. A similar procedure is used to determine the value of RTC using Equation 2. The value of RTC selected is the series combination of 17.4kΩ and 1.27kΩ. See section “Overcurrent Component Selection” on page 18 for further explanation. VOUT is the output voltage If we allow a current ramp, ΔI, of 5% of the rated output current, the minimum inductance required is: V L • T ON 0.25 • 2.08 L ≥ ---------------------- = ----------------------------- = 1.04 ΔI 0.5 The output filter inductor and capacitor selection is simple and straightforward. Under steady state operating conditions the voltage across the inductor is very small due to the large duty cycle. Voltage is applied across the inductor only during the switch transition time, about 45ns in this application. Ignoring the voltage drop across the SR FETs, the voltage across the inductor during the ON time with VIN = 48V is: V IN • N S • ( 1 – D ) V L = V S – V OUT = --------------------------------------------- ≈ 250 2N P mV (EQ. 23) An inductor value of 1.4μH, rated for 18A was selected. With a maximum input voltage of 53V, the maximum output voltage is about 13V. The closest higher voltage rated capacitor is 16V. Under steady state operating conditions the ripple current in the capacitor is small, so it would seem appropriate to have a low ripple current rated capacitor. However, a high rated ripple current capacitor was selected based on the nature of the intended load, multiple buck regulators. To minimize the output impedance of the filter, a Sanyo OSCON 16SH150M capacitor in parallel with a 22μF ceramic capacitor were selected. Overcurrent Component Selection There are two circuit areas to consider when selecting the components for overcurrent protection, current limit and short circuit shutdown. The current limit threshold is fixed at 0.6V while the short circuit threshold is set to a fraction of the duty cycle the designer wishes to define as a short circuit. The current level that corresponds to the overcurrent threshold must be chosen to allow for the dynamic behavior of an open loop converter. In particular, the low inductor ripple current under steady state operation increases significantly as the duty cycle decreases. 14 V (L1:1) I (L1) 13 12 11 10 9 8 0.9950 Output Filter Design μH 0.9960 0.9970 0.9980 0.9990 1.000 TIME (ms) FIGURE 8. STEADY STATE SECONDARY WINDING VOLTAGE AND INDUCTOR CURRENT (EQ. 22) where VL is the inductor voltage VS is the voltage across the secondary winding 18 FN9111.6 December 2, 2011 ISL6740, ISL6741 and line regulation performance are demonstrated in the following figures. 15 V (L1:1) I (L1) EFFICIENCY (%) 100 10 95 90 85 80 75 70 0 5 0.986 0.988 0.990 0.992 0.994 0.996 0.998 1 2 3 4 5 6 LOAD CURRENT (A) 7 8 9 FIGURE 10. EFFICIENCY vs LOAD VIN = 48Vt 1.000 TIME (ms) The short circuit protection involves setting a voltage between 0 and 2V on the SCSET pin. The applied voltage divided by 2 is the percent of maximum duty cycle that corresponds to a short circuit when the peak current limit is active. A divider from RTC to ground provides an easy method to achieve this. The divider between RTC and GND formed by R13 and R15 determines the percent of maximum duty cycle that corresponds to a short circuit. The divider ratio formed by R13 and R15 is: R15 1.27k ----------------------------- = ------------------------------------- = 0.068 R13 + R15 1.27k + 17.4k (EQ. 24) Therefore, the duty cycle that corresponds to a short circuit is 6.8% of D max (97.9%), or ~6.6%. Performance The major performance criteria for the converter are efficiency, and to a lesser extent, load regulation. Efficiency, load regulation 19 OUTPUT VOLTAGE (V) Figures 8 and 9 show the behavior of the inductor ripple under steady state and overcurrent conditions. In this example, the peak current limit is set at 11A. The peak current limit causes the duty cycle to decrease resulting in a reduction of the average current through the inductor. The implication is that the converter can not supply the same output current in current limit that it can supply under steady state conditions. The peak current limit setpoint must take this behavior into consideration. A 3.32Ω current sense resistor was selected for the rectified secondary of current transformer T2, corresponding to a peak current limit setpoint of 16.5A. 12.5 12.25 12.00 11.75 11.50 11.25 11 0 1 2 3 4 5 6 7 LOAD CURRENT (A) 8 9 FIGURE 11. LOAD REGULATION AT VIN = 48V 14.0 OUPUT VOLTAGE (V) FIGURE 9. SECONDARY WINDING VOLTAGE AND INDUCTOR CURRENT DURING CURRENT LIMIT OPERATION 13.5 13.0 12.5 12.0 11.5 11.0 45 46 47 48 49 50 51 52 INPUT VOLTAGE (V) 53 54 FIGURE 12. LINE REGULATION AT I OUT = 1A As expected, the output voltage varies considerably with line and load when compared to an equivalent converter with closed loop feedback. However, for applications where tight regulation is not required, such as those application that use downstream DC/DC converters, this design approach is viable. FN9111.6 December 2, 2011 ISL6740, ISL6741 Waveforms Typical waveforms can be found in the following Figures. Figure 13 shows the output voltage during start up. FIGURE 15. FET DRAIN-SOURCE VOLTAGE FIGURE 13. OUTPUT SOFT-START Figure 14 shows the output voltage ripple and noise at a 5A load. FIGURE 16. FET D-S VOLTAGE NEAR-ZVS TRANSITION FIGURE 14. OUTPUT RIPPLE AND NOISE (20MHz BW) Figures 15 and 16 show the voltage waveforms at the switching node shared by the upper FET source and the lower FET drain. In particular, Figure 16 shows near ZVS operation at 8A of load when the upper FET is turning off and the lower FET turning on. There is insufficient energy stored in the leakage inductance to allow complete ZVS operation. However, since the energy stored in the node capacitance is proportional to V2, a significant portion of the energy is still recovered. Figure 17 shows the switching transition between outputs, OUTA and OUTB during steady state operation. The deadtime duration of 48.6ns is clearly shown. FIGURE 17. OUTA TO OUTB TRANSITION 20 FN9111.6 December 2, 2011 ISL6740, ISL6741 Adding Line Only Regulation - Feed Forward Component List REFERENCE DESIGNATOR VALUE DESCRIPTION C1 1.0μF Capacitor, 1812, X7R, 100V, 20% TDK C4532X7R2A105M C2, C3 3.3μF Capacitor, 1812, X5R, 50V, 20% TDK C4532X5R1H335M C4, C6 1.0μF Capacitor, 0805, X5R, 16V, 10% TDK C2012X5R1C105K C5, C15, C16 0.1μF Capacitor, 0603, X7R, 50V, 10% TDK C1608X7R1H104K C7 Open Capacitor, 0603, Open C8 22μF Capacitor, 1812, X5R, 16V, 20% TDK C4532X5R1C226M C9 150μF Output voltage variation caused by changes in the supply voltage may be virtually removed through a technique known as feed forward compensation. Using feed forward, the duty cycle is directly controlled based on changes in the input voltage only. No closed loop feedback system is required. Voltage feed forward may be implemented as shown in Figure 18. 1.5V Capacitor, 0603, COG, 16V, 5% TDK C1608COG1C221J C18 0.047μF Capacitor, 0603, X7R, 16V, 10% TDK C1608X7R1C473K CR1, CR2 Diode, Schottky, BAT54S CR3 Diode, Schottky, BAT54 D1 Zener, 10V, Philips BZX84-C10 L1 190nH Pulse, P2004T L2 1.5μH Pulse, PG0077.142 L3 Short Jumper or Optional Discrete Leakage Inductance Q5 Transistor, ON MJD31C Q L, Q H FET, Fairchild FDS3672 QR1, QR2, QR3, QR4 FET, Fairchild FDS5670 0.8V +VIN R106 100K R103 49.9k R100 69.8k + - Capacitor, Radial, Sanyo 16SH150M 220pF R111 806 VREF U100A U100B + - R105 100k R102 100k C10, C11, C12, 1000pF Capacitor, 0603, X7R, 50V, 10% C13, C14 TDK C1608X7R1H102K C17 R110 698 R109 3.48k to VERROR R104 100k R101 2k R107 100k C100 1nF R108 100k FIGURE 18. VOLTAGE FEED FORWARD CIRCUIT The circuit provides feed forward compensation for a 2:1 input voltage range. Resistors R100 and R101 set the input voltage divider to generate a 1V signal at the input voltage that corresponds to maximum duty cycle (VIN minimum). Resistors R109, R110, and R111 form a voltage divider from VREF to create reference voltages for the amplifiers. The first stage uses U100A, R102, R103, R104, and C100 to form a unity gain inverting amplifier. Its output varies inversely with input voltage and ranges from 1V to 2V. The bandwidth of the circuit may be controlled by varying the value of C100. The gain of the first amplifier stage is: R1, R10 3.3 Resistor, 2512, 5% R2 3.01k Resistor, 2512, 1% R3, R6 10.0 Resistor, 0603, 1% R5 3.32 Resistor, 0603, 1% R7 75.0k Resistor, 0805, 1% R8, R9 20.0 Resistor, 0805, 1% VA = Output voltage of U100A R11 100 Resistor, 0603, 1% VD = The input divider voltage R12 8.06k Resistor, 0603, 1% R13 17.4k Resistor, 0603, 1% R14 Open Resistor, 0603, Open R15 1.27k Resistor, 0603, 1% R17 97.6k Resistor, 0603, 1% The second stage uses U100B, R105, R106, R107, and R108 to form a summing amplifier which offsets the first stage output by 0.8V (the value of CT valley voltage). The signal applied to the VERROR input now matches the offset and amplitude of the oscillator sawtooth so that the duty cycle varies linearly from 100% to 50% of maximum with a 2:1 input voltage variation. R18 3.01k Resistor, 0603, 1% R19, RT1 10.0k Resistor, 0603, 1% T1 Midcom 31718 T2 Pulse P8205T U1 Intersil HIP2101IB U3 ISL6740IB 21 V A = – V D + 3.00 V (EQ. 25) where: FN9111.6 December 2, 2011 ISL6740, ISL6741 Other duty ranges are possible, but are still limited to a 2:1 ratio. The voltage applied to VERROR must be scaled to the peak-topeak voltage on CT, and offset by the valley voltage. Since the peak-to-peak CT voltage is 2.00V nominal, the voltage at the output of U100A must be divided by 2.0V to obtain the desired duty cycle. For example, if an 80% duty cycle was required at the minimum operating voltage, the output of U100A must be 1.60V (80% of 2.00V). From (Equation 25), the divider voltage must be set to 1.4V for the input voltage that corresponds to the 80% duty cycle. It should be noted that the synchronous rectifiers (SRs), being driven from the transformer secondary, are only gated on during the ON time of the primary FETs. Conduction continues through the body diodes during the OFF time when operating in continuous inductor current mode. This mode of operation usually results in significant conduction and switching losses in the SR FETs. These losses may be reduced considerably by either adding schottky diodes in parallel to the SR FETs or by driving the SR FETs directly with a control signal. A block diagram of the feedback control loop follows in Figure 19. POWER STAGE PWM VOUT ERROR AMPLIFIER Z2 ISOLATION + Z1 REF FIGURE 19. CONTROL LOOP BLOCK DIAGRAM The loop compensation is placed around the Error Amplifier (EA) on the secondary side of the converter. A Type 3 error amplifier configuration was selected. Adding Regulation - Closed Loop Feedback The second Typical Application schematic adds closed loop feedback with isolation. The ISL6740EVAL2Z demonstration platform implements this design and is available for evaluation. The input voltage range was increased to 36V to 75V, which necessitates a few modifications to the open loop design. The output inductor value was increased to 4.0μH, schottky rectifier CR4 was added to minimize SR FET body diode conduction, the turns ratio of the main transformer was changed to 4:3, and the synchronous rectifier gate drives were modified. The design process is essentially the same as it was for the unregulated version, so only the feedback control loop design will be discussed. The major components of the feedback control loop are a programmable shunt regulator and an opto-coupler. The optocoupler is used to transfer the error signal across the isolation barrier. The opto-coupler offers a convenient means to cross the isolation barrier, but it adds complexity to the feedback control loop. It adds a pole at about 10kHz and a significant amount of gain variation due the current transfer ratio (CTR). The CTR of the opto-coupler varies with initial tolerance, temperature, forward current, and age. VOUT - VERR + REF FIGURE 20. TYPE 3 ERROR AMPLIFIER The control to output transfer function may be represented as [1] s 1 + -----V IN NS vo ωz ----- = --------------- • ------- • -----------------------------------------------vc VS • 2 NP s 2 s 1 + ---------------- + ⎛ -------⎞ ⎝ω ⎠ ( Q )ω o (EQ. 26) o where: Ro Q = --------------ωo • L 1 ω o = ----------LC or 1 f o = -----------------2π LC 1 ω z = ---------Rc C or 1 f z = -----------------2πR c C Ro = Output Load Resistance L = Output Inductance C = Output Capacitance Rc = Output Capacitance ESR VS = Sawtooth Ramp Amplitude Gain and phase plots of (Equation 26) appear below using L = 4.0μH, C = 150μF, Rc = 28mΩ, Ro = 1.2Ω, and VIN = 75V. 22 FN9111.6 December 2, 2011 ISL6740, ISL6741 The higher the desired bandwidth of the converter, the more difficult it is to create a solution that is stable over the entire operating range. A good rule of thumb is to limit the bandwidth to about fSW/4, where fSW is the switching frequency of the converter. However, due to the bandwidth constraints of the optocoupler and the LM431 shunt regulator, the bandwidth was reduced to about 25kHz. 40 30 GAIN (dB) 20 10 0 -10 -20 10 100 1•103 1•104 FREQUENCY (Hz) 1•105 1•106 FIGURE 21A. CONTROL-TO-OUTPUT GAIN 50 Some liberties where taken with the generally accepted compensation procedure described above due to the transfer characteristics of the opto coupler. The effects of the optocoupler tend to dominate over those of the LM431 so the GBWP effects of the LM431 are not included here. 0 PHASE (DEGREES) The first pole is placed at the origin by default (C20 is an integrating capacitor). If the two zeroes are placed at the same frequency, they should be placed at fLC/2, where fLC is the resonant frequency of the output L-C filter. To reduce the gain peaking at the L-C resonant frequency, the two zeroes are often separated. When they are separated, the first zero may be placed at fLC/5, and the second at just above fLC. The second pole is placed at the lowest expected zero cause by the output capacitor ESR. The third, and last pole is placed at about 1.5 times the cross over frequency. -50 The gain and phase characteristics of the opto coupler are shown in Figure 22A. -100 10 -150 5 10 100 1•103 1•104 FREQUENCY (Hz) 1•105 1•106 FIGURE 21B. CONTROL-TO-OUTPUT PHASE The Type 3 compensation configuration has three poles and two zeros. The first pole is at the origin, and provides the integration characteristic which results in excellent DC regulation. Referring to the Typical Application Schematic for the regulated output, the remaining poles and zeros for the compensator are located at: -5 -10 -15 -20 10 1 f p2 = ----------------------------------------2π • R21 • C20 1 f p3 ≈ ------------------------------------2π • R4 • C22 0 GAIN (dB) -200 100 (EQ. 27) 1•103 1•104 1•105 1•106 FREQUENCY (Hz) FIGURE 22A. OPTO COUPLER GAIN C19 » C20 (EQ. 28) 90 1 f z1 = ----------------------------------------2π • R21 • C19 R23 » R4 (EQ. 30) From (Equation 26), it can be seen that the control to output transfer function frequency dependence is a function of the output load resistance, the value of output capacitor and inductor, and the output capacitance ESR. These variations must be considered when compensating the control loop. The worst case small signal operating point for a voltage mode converter tends to be at maximum Vin, maximum load, maximum COUT, and minimum ESR. 23 PHASE (DEGREES) 1 f z2 ≈ ----------------------------------------2π • R23 • C22 (EQ. 29) 45 0 -45 -90 10 100 1•103 1•104 1•105 1•106 FREQUENCY (Hz) FIGURE 22B. OPTO COUPLER FN9111.6 December 2, 2011 ISL6740, ISL6741 The following compensation components were selected R23 = 9.53kΩ The gain and phase plots combined with the opto coupler’s transfer characteristics appear in Figures 24A and 24B: 30 R24 = 2.49kΩ R4 = 499Ω 20 GAIN (dB) R21 = 4.22kΩ C22 = 1nF C20 = 82pF C19 = 0.22μF 10 0 From (Equations 27, 28, 29 and 30), the poles and zeroes are: fz1 = 171Hz -10 10 100 fz2 = 16.7kHz 1•103 1•104 1•105 1•106 FREQUENCY (Hz) fp2 = 460kHz FIGURE 24A. EA PLUS OPTO COUPLER GAIN fp3 = 319kHz 90 The calculated gain and phase plots of the error amplifier appear below using an ideal op amp. PHASE (DEGREES) 45 20 GAIN (dB) 10 0 -45 -90 -135 0 -180 10 100 1•103 1•104 FREQUENCY (Hz) 1•105 1•106 FIGURE 24B. EA PLUS OPTO COUPLER GAIN -10 10 100 1•103 1•104 1•105 1•106 Using the control-to-output transfer function combined with the EA transfer function, the loop gain and phase may be predicted. The predicted loop gain and phase margin of the converter appear in Figures 25A and 25B: FREQUENCY (Hz) FIGURE 23A. IDEAL ERROR AMPLIFIER GAIN 90 50 40 45 20 0 GAIN (dB) PHASE (°) 30 -45 10 0 -10 -20 -30 -90 10 100 1•103 1•104 1•105 1•106 FREQUENCY (Hz) FIGURE 23B. IDEAL ERROR AMPLIFIER PHASE -40 -50 100 1•103 1•104 1•105 FREQUENCY (Hz) FIGURE 25A. PREDICTED LOOP GAIN 24 FN9111.6 December 2, 2011 ISL6740, ISL6741 as the FET on resistance, copper losses, and inductor resistance. The phase discrepancy above 60kHz is not particularly relevant to the loop performance since it occurs well above the cross over frequency. The predicted behavior indicates a much gentler drop off of phase than was observed in the measured performance. The discrepancy was not investigated. 225 PHASE MARGIN (°) 180 135 90 45 Performance 0 The major performance criteria for the converter are efficiency and load regulation. These quantities are detailed in Figures 27 and 28. -45 -90 -135 100 1•103 1•104 1•105 95 FREQUENCY (Hz) 93 The actual loop gain and phase margin measured on the ISL6740EVAL2Z demonstration board appear in Figures 26A and 26B: EFFICIENCY (%) FIGURE 25B. PREDICTED LOOP PHASE MARGIN 91 89 87 50 40 85 30 2 3 4 GAIN (dB) 20 5 6 7 8 9 10 LOAD CURRENT (A) 10 FIGURE 27. EFFICIENCY vs LOAD VIN = 48Vt 0 -10 -20 12.015 -30 -50 0.1k 1k 10k 100k FREQUENCY (Hz) FIGURE 26A. MEASURED LOOP GAIN 225 PHASE MARGIN (°) 180 12.010 12.005 12.000 11.995 135 0 1 2 3 4 5 6 7 8 9 10 LOAD CURRENT (A) 90 FIGURE 28. LOAD REGULATION AT VIN = 48V 45 0 -45 -90 -135 0.1k OUTPUT VOLTAGE (V) -40 1k 10k 100k FREQUENCY (Hz) FIGURE 26B. MEASURE LOOP PHASE MARGIN The efficiency, although very good, could be further improved using a controlled SR method instead of using a self-driven method with an auxiliary schottky diode. The schottky diode conducts when the main switching FETs are off. Its forward voltage drop is considerably larger than that of the SR FETs and causes a measurable reduction in efficiency. The effect becomes more significant as the input voltage is increased due to the reduction of duty cycle (and consequent increase in the OFF time). The only major discrepancies between the predicted behavior and the measured results are the Q of the L-C filter and the phase behavior above 60kHz. The actual Q appears to be significantly less than predicted resulting in less gain peaking and a less rapid phase shift near the resonant frequency. This is most likely the result of neglecting other losses in the converter’s output, such 25 FN9111.6 December 2, 2011 ISL6740, ISL6741 Component List REFERENCE DESIGNATOR VALUE Component List (Continued) DESCRIPTION C1 1.0μF Capacitor, 1812, X7R, 100V, 20% TDK C4532X7R2A105M C2, C3 3.3μF Capacitor, 1812, X5R, 50V, 20% TDK C4532X5R1H335M C4, C6 1.0μF Capacitor, 0805, X5R, 16V, 10% TDK C2012X5R1C105K REFERENCE DESIGNATOR VALUE DESCRIPTION R8, R9, R10 18 Resistor, 2512, 5% R11 205 Resistor, 0603, 1% R12 8.06k Resistor, 0603, 1% R13 18.2k Resistor, 0603, 1% R14 Open Resistor, 0603, Open R15 1.27k Resistor, 0603, 1% R16, R19 1.00k Resistor, 0603, 1% R17 97.6k Resistor, 0603, 1% R18 3.01k Resistor, 0603, 1% C5, C15, C16 0.1μF Capacitor, 0603, X7R, 50V, 10% TDK C1608X7R1H104K C7 Open Capacitor, 0603, Open C8, C21 22μF Capacitor, 1812, X5R, 16V, 20% TDK C4532X5R1C226M C9 150μF Capacitor, Radial, Sanyo 16SH150M R20 2.00k Resistor, 0603, 1% C10, C14, C22 1000pF Capacitor, 0603, X7R, 50V, 10% TDK C1608X7R1H102K R21 4.22k Resistor, 0603, 1% R23 9.53k Resistor, 0603, 1% C11, C12 560 pF Capacitor, 0603, X7R, 100V, 10% TDK C1608X7R2A561K R24 2.49k Resistor, 0603, 1% C13 220pF Capacitor, 0603, X7R, 100V, 10% TDK C1608X7R2A221K R26, R27 5.11 Resistor, 0805, 1% RT1 10.0k Resistor, 0603, 1% C17 220pF C18 0.047μF Capacitor, 0603, X7R, 16V, 10% TDK C1608X7R1C473K C19 0.22μF C20 82pF Capacitor, 0603, COG, 16V, 5% TDK C1608COG1C221J Capacitor, 0603, X7R, 16V, 10% TDK C1608X7R1C224K Capacitor, 0603, X7R, 16V, 10% TDK C1608X7R1C820K CR1, CR2 Diode, Schottky, BAT54S CR3, CR5, CR6 Diode, Schottky, BAT54 CR4 Diode, Schottky, IR 12CWQ06FNPBF D1 Zener, 10V, Philips BZX84-C10 D2 Zener, 6.8V, Philips BZX84-C6V8 L1 190nH Pulse, P2004NL L2 4.0μH BI Technologies, HM65-H4R0LF L3 Short 0 Ohm Jumper Q5 Transistor, ONSemi MJD31CG QL, QH, QR1, QR2, QR3, QR4 FET, Fairchild FDS3672 R1 3.3 Resistor, 2512, 5% R2 3.01k Resistor, 2512, 2% R3 10.0 Resistor, 0603, 1% R4, R25 499 Resistor, 0603, 1% R5 2.20 Resistor, 0805, 1% R6 200 Resistor, 0603, 1% R7 75.0k Resistor, 0805, 1% 26 T1 Midcom 31660-LF1 T2 Pulse P8205NL U1 Intersil HIP2101IBZ U2 NEC PS2801-1-A U3 ISL6740IBZ U4 National LM431BIM3/NOPB References [1] Dixon, Lloyd H., “Closing the Feedback Loop”, Unitrode Power Supply Design Seminar, SEM-700, 1990. FN9111.6 December 2, 2011 ISL6740, ISL6741 Package Outline Drawing M16.173 16 LEAD THIN SHRINK SMALL OUTLINE PACKAGE (TSSOP) Rev 2, 5/10 A 1 3 5.00 ±0.10 SEE DETAIL "X" 9 16 6.40 PIN #1 I.D. MARK 4.40 ±0.10 2 3 0.20 C B A 1 8 B 0.65 0.09-0.20 END VIEW TOP VIEW 1.00 REF - 0.05 H C 1.20 MAX SEATING PLANE 0.90 +0.15/-0.10 GAUGE PLANE 0.25 +0.05/-0.06 5 0.10 M C B A 0.10 C 0°-8° 0.05 MIN 0.15 MAX SIDE VIEW 0.25 0.60 ±0.15 DETAIL "X" (1.45) NOTES: 1. Dimension does not include mold flash, protrusions or gate burrs. (5.65) Mold flash, protrusions or gate burrs shall not exceed 0.15 per side. 2. Dimension does not include interlead flash or protrusion. Interlead flash or protrusion shall not exceed 0.25 per side. 3. Dimensions are measured at datum plane H. 4. Dimensioning and tolerancing per ASME Y14.5M-1994. 5. Dimension does not include dambar protrusion. Allowable protrusion shall be 0.08mm total in excess of dimension at maximum material condition. Minimum space between protrusion and adjacent lead (0.65 TYP) (0.35 TYP) TYPICAL RECOMMENDED LAND PATTERN is 0.07mm. 6. Dimension in ( ) are for reference only. 7. Conforms to JEDEC MO-153. 27 FN9111.6 December 2, 2011 ISL6740, ISL6741 Small Outline Plastic Packages (SOIC) M16.15 (JEDEC MS-012-AC ISSUE C) N INDEX AREA H 0.25(0.010) M 16 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE B M INCHES E -B1 2 3 L SEATING PLANE -A- A D h x 45° -C- e A1 B 0.25(0.010) M C 0.10(0.004) C A M SYMBOL MIN MAX MIN MAX NOTES A 0.0532 0.0688 1.35 1.75 - A1 0.0040 0.0098 0.10 0.25 - B 0.013 0.020 0.33 0.51 9 C 0.0075 0.0098 0.19 0.25 - D 0.3859 0.3937 9.80 10.00 3 E 0.1497 0.1574 3.80 4.00 4 e α B S 0.050 BSC 1.27 BSC - H 0.2284 0.2440 5.80 6.20 - h 0.0099 0.0196 0.25 0.50 5 L 0.016 0.050 0.40 N α NOTES: MILLIMETERS 16 0° 1.27 16 8° 0° 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. 6 7 8° Rev. 1 6/05 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. For additional products, see www.intersil.com/product_tree Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted in the quality certifications found at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 28 FN9111.6 December 2, 2011