PART NUMBER: CPE-165 page 1 of 5 date 11/12/2007 DESCRIPTION: piezo audio transducer SPECIFICATONS operating voltage current consumption sound pressure level electrostatic capacity operating tempurature storage tempurature dimensions weight material terminal RoHS 30 Vp-p max. 11 mA max. at 10 Vp-p, sqaure wave, 4.8 Khz 85 db min. at 10 cm/10 Vp-p, sqaure wave, 4.8 Khz 15,000 ± 30% at 1 Khz/1 V -30 ~ +85° C -40 ~ +95° C Ø14.0 x H4.0 mm 1.0 g max. ABS UL-94 1/16” HB high heat (black) wire type yes APPEARANCE DRAWING tolerance: ±0.5 units: mm 4.0 14.0 UL1571 LF 32AWG 5.0 2.0 90.0 5.0 red black 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 PART NUMBER: CPE-165 page 2 of 5 date 11/12/2007 DESCRIPTION: piezo audio transducer FREQUENCY RESPONSE CURVE MEASUREMENT METHOD S.P.L. Measuring Circuit Input Signal: 10 Vp-p, 4.8 KHz, square wave Mic: RION S.P.L. meter UC30 or equivalent S.G.: Hewlett Packard 33120A function generator or equivalent 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 page 3 of 5 date 11/12/2007 DESCRIPTION: piezo audio transducer PART NUMBER: CPE-165 MECHANICAL CHARACTERISTICS item solderability soldering heat resistance lead wire pull strength vibration drop test bottom covering pull force test condition Stripped wires are immersed in rosin for 5 seconds and then immersed in solder bath of 270 ±5°C for 3 ±1 seconds. Stripped wires are immersed up to 1.5mm from buzzer’s body in solder bath of 300 ±5°C for 3 ±0.5 seconds or 260 ±5°C for 10 ±1 seconds. The pull force shall be applied to lead wire: Horizontal 3.0N Vertical 2.0N The buzzer shall be measured after applying a vibration amplitude of 1.5 mm with 10 to 55 Hz band of vibration frequency to each of the 3 perpendicular directions for 2 hours. The part will be dropped from a height of 75 cm onto a 40 mm thick wooden board 3 times in 3 axes (X, Y, Z) for a total of 9 drops. The pull force of 3.0N shall be applied to bottom covering on the vertical direction. evaluation standard 90% min. of the lead terminals will be wet with solder (except the edge of the terminal). test condition After being placed in a chamber at +95°C for 240 hours. After being placed in a chamber at -40°C for 240 hours. After being placed in a chamber at +40°C and 90±5% relative humidity for 240 hours. The part shall be subjected to 5 cycles. One cycle will consist of: evaluation standard No interference in operation. No damage or cutting off. The value of oscillation frequency/current consumption should be ±10% of the initial measurements. The SPL should be within ±10dB compared with the initial measurement. No damage or cutting off. ENVIRONMENT TEST item high temp. test low temp. test humidity test temp. cycle test +95 +25 +25 -40 0.5hr 0.5hr 0.25 0.5hr 0.5hr The buzzer will be measured after being placed at +25°C for 4 hours. The value of the oscillation frequency/current consumption should be ±10% compared to the initial measurements. The SPL should be within ±10dB compared to the initial measurements. 0.5hr 0.25 3hours 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 page 4 of 5 date 11/12/2007 DESCRIPTION: piezo audio transducer PART NUMBER: CPE-165 RELIABILITY TEST item operating (life test) test condition 1. Continuous life test: The part will be subjected to 48 hours of continuous operation at +70°C with rated voltage applied. 2. Intermittent life test: A duty cycle of 1 minute on, 1 minutes off, a minimum of 5,000 times at room temp (+25 ±2°C) with rated voltage applied. evaluation standard The buzzer will be measured after being placed at +25°C for 4 hours. The value of the oscillation frequency/current consumption should be ±10% compared to the initial measurements. The SPL should be within ±10dB compared to the initial measurements. TEST CONDITIONS standard test condition judgement test condition a) tempurature: +5 ~ +35°C a) tempurature: +25 ±2°C b) humidity: 45 - 85% b) humidity: 60 - 70% c) pressure: 860-1060 mbar c) pressure: 860-1060 mbar 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 PART NUMBER: CPE-165 page 5 of 5 date 11/12/2007 DESCRIPTION: piezo audio transducer PACKAGING 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383