ATF1502AS and ATF1502ASL High-performance EEPROM Complex Programmable Logic Device DATASHEET Features High-density, High-performance, Electrically-erasable Complex Programmable Logic Device ̶ 32 Macrocells 5 Product Terms per Macrocell, Expandable up to 40 per Macrocell 44 Pins 7.5ns Maximum Pin-to-pin Delay Registered Operation up to 125MHz Enhanced Routing Resources ̶ ̶ ̶ ̶ ̶ In-System Programmability (ISP) via JTAG Flexible Logic Macrocell ̶ ̶ D/T Latch Configurable Flip-flops Global and Individual Register Control Signals Global and Individual Output Enable Programmable Output Slew Rate Programmable Output Open Collector Option Maximum Logic Utilization by Burying a Register with a COM Output ̶ ̶ ̶ ̶ Advanced Power Management Features ̶ ̶ Automatic 10μA Standby for “L” Version Pin-controlled 1mA Standby Mode Programmable Pin-keeper Inputs and I/Os Reduced-power Feature per Macrocell ̶ ̶ Available in Commercial and Industrial Temperature Ranges Available in 44-lead PLCC and 44-lead TQFP Advanced EEPROM Technology ̶ ̶ ̶ ̶ ̶ ̶ 100% Tested Completely Reprogrammable 10,000 Program/Erase Cycles 20 Year Data Retention 2000V ESD Protection 200mA Latch-up Immunity JTAG Boundary-scan Testing to IEEE Std. 1149.1-1990 and 1149.1a-1993 Supported PCI-compliant Security Fuse Feature Green (Pb/Halide-fee/RoHS Compliant) Package Options Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 Enhanced Features Improved Connectivity (Additional Feedback Routing, Alternate Input Routing) Output Enable Product Terms D Latch Mode Combinatorial Output with Registered Feedback within Any Macrocell Three Global Clock Pins ITD (Input Transition Detection) Circuits on Global Clocks, Inputs and I/O (“L” Versions) Fast Registered Input from Product Term Programmable “Pin-keeper” Option VCC Power-up Reset Option Pull-up Option on JTAG Pins TMS and TDI Advanced Power Management Features ̶ ̶ ̶ ̶ Input Transition Detection Power-down (“L” Versions) Individual Macrocell Power Option Disable ITD on Global Clocks, Inputs, and I/O Description The Atmel® ATF1502AS(L) is a high-performance, high-density Complex Programmable Logic Device (CPLD) which utilizes the Atmel proven electrically-erasable technology. With 32 logic macrocells and up to 36 inputs, it easily integrates logic from several TTL, SSI, MSI, LSI, and classic PLDs. The ATF1502AS(L)’s enhanced routing switch matrices increase usable gate count and the odds of successful pin-locked design modifications. The ATF1502AS(L) has up to 32 bi-directional I/O pins and four dedicated input pins, depending on the type of device package selected. Each dedicated pin can serve as a global control signal, register clock, register reset, or output enable. Each of these control signals can be selected for use individually within each macrocell. Each of the 32 macrocells generates a buried feedback which goes to the global bus. Each input and I/O pin also feeds into the global bus. The switch matrix in each logic block then selects 40 individual signals from the global bus. Each macrocell also generates a foldback logic term that goes to a regional bus. Cascade logic between macrocells in the ATF1502AS(L) allows fast, efficient generation of complex logic functions. The ATF1502AS(L) contains four such logic chains, each capable of creating sum term logic with a fan-in of up to 40 product terms. The ATF1502AS(L) macrocell, shown in Figure 1, is flexible enough to support highly complex logic functions operating at high speed. The macrocell consists of five sections: 2 Product Terms and Product Term Select Multiplexer OR/XOR/CASCADE Logic Flip-flop Output Select and Enable Logic Array Inputs ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 ATF1502AS(L) Macrocell SWITCH REGIONAL MATRIX FOLDBACK OUTPUTS BUS LOGIC FOLDBACK CASIN GOE[0:5] MOE SWITCH MATRIX Figure 1. I/O Pin I/O Pin PTMUX GCK[0:2] GCLEAR- CASOUT SLEW RATE OPEN COLLECTOR OPTION MACROCELL REDUCED POWER BIT GLOBAL BUS ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 3 1. Pin Configurations and Pinouts Figure 1-1. Pinouts 44-lead TQFP 44-lead PLCC (Top View) 33 32 31 30 29 28 27 26 25 24 23 1 2 3 4 5 6 7 8 9 10 11 I/O I/O/TDO I/O I/O VCC I/O I/O I/O/TCK I/O GND I/O 6 5 4 3 2 1 44 43 42 41 40 TDI/I/O I/O I/O GND PD1/I/O I/O I/O/TMS I/O VCC I/O I/O 7 8 9 10 11 12 13 14 15 16 17 39 38 37 36 35 34 33 32 31 30 29 I/O I/O I/O I/O GND VCC I/O PD2/I/O I/O I/O I/O I/O I/O I/O I/O GND VCC I/O PD2/I/O I/O I/O I/O 12 13 14 15 16 17 18 19 20 21 22 I/O/TDI I/O I/O GND PD1/I/O I/O TMS/I/O I/O VCC I/O I/O 18 19 20 21 22 23 24 25 26 27 28 44 43 42 41 40 39 38 37 36 35 34 I/O I/O I/O VCC GCLK2/OE2/I GCLR/I I/OE1 GCLK1/I GND GCLK3/I/O I/O I/O I/O I/O VCC GCLK2/OE2/I GCLR/I OE1/I GCLK1/I GND GCLK3/I/O I/O (Top View) 44-lead TQFP Top View 44-lead PLCC Top View 4 ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 I/O I/O/TDO I/O I/O VCC I/O I/O I/O/TCK I/O GND I/O Block Diagram Figure 2-1. Block Diagram I/O (MC32)/GCLK3 Output Enable Switch Matrix Global Clock Mux GCK[0:2] I/O Pins GCK[0:2] GOE[0:5] Logic Block B GOE[0:5] GCLEAR GCK[0:2] I/O Pins GCLEAR Switch Matrix Macrocells 1 to 16 GLOBAL BUS (INPUTS and FEEDBACKS BUS) Regional Foldbacks Logic Block A GOE[0:5] 2. OE1/INPUT INPUT/GCLK1 INPUT/OE2/GCLK2 Global Clear Mux GCLEAR INPUT/GCLR Unused product terms are automatically disabled by the compiler to decrease power consumption. A security fuse, when programmed, protects the contents of the ATF1502AS(L). Two bytes (16 bits) of User Signature are accessible to the user for purposes such as storing project name, part number, revision, or date. The User Signature is accessible regardless of the state of the security fuse. The ATF1502AS(L) device is an In-System Programmable (ISP) device. It uses the industry standard 4-pin JTAG interface (IEEE Std. 1149.1), and is fully compliant with JTAG’s Boundary-scan Description Language (BSDL). ISP allows the device to be programmed without removing it from the printed circuit board. In addition to simplifying the manufacturing flow, ISP also allows design modifications to be made in the field via software. ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 5 3. Macrocell Sections Table 3-1. Macrocell Sections Section Product Terms and Select Mux OR/XOR/CASCADE Logic Description Each ATF1502AS(L) macrocell has five product terms. Each product term receives as its inputs all signals from both the global bus and regional bus. The Product Term Select Multiplexer (PTMUX) allocates the five product terms as needed to the macrocell logic gates and control signals. The PTMUX programming is determined by the design compiler, which selects the optimum macrocell configuration. The ATF1502AS(L) logic structure is designed to efficiently support all types of logic. Within a single macrocell, all the product terms can be routed to the OR gate, creating a 5-input AND/OR sum term. With the addition of the CASIN from neighboring macrocells, this can be expanded to as many as 40 product terms with little additional delay. The macrocell’s XOR gate allows efficient implementation of compare and arithmetic functions. One input to the XOR comes from the OR sum term. The other XOR input can be a product term or a fixed high or low level. For combinatorial outputs, the fixed level input allows polarity selection. For registered functions, the fixed levels allow DeMorgan minimization of product terms. The XOR gate is also used to emulate T-type and JK-type flip-flops. The ATF1502AS(L) flip-flop has very flexible data and control functions. The data input can come from either the XOR gate, from a separate product term, or directly from the I/O pin. Selecting the separate product term allows creation of a buried registered feedback within a combinatorial output macrocell. (This feature is automatically implemented by the fitter software). In addition to D, T, JK, and SR operation, the flip-flop can be configured as a flow-through latch. In this mode, data passes through when the clock is high and is latched when the clock is low. Flip-flop The clock itself can be either one of the Global CLK signals (GCK[0:2]) or an individual product term. The flip-flop changes state on the clock’s rising edge. When the GCK signal is used as the clock, one of the macrocell product terms can be selected as a clock enable. When the clock enable function is active and the enable signal (product term) is low, all clock edges are ignored. The flip-flop’s Asynchronous Reset (AR) signal can be either the Global Clear (GCLEAR), a product term, or always off. AR can also be a logic OR of GCLEAR with a product term. The Asynchronous Preset (AP) can be a product term or always off. The ATF1502AS(L) macrocell output can be selected as registered or combinatorial. The extra buried feedback signal can be either combinatorial or a registered signal regardless of whether the output is combinatorial or registered. (This enhancement function is automatically implemented by the fitter software.) Feedback of a buried combinatorial output allows the creation of a second latch within a macrocell. 6 Extra Feedback I/O Control: The Output Enable Multiplexer (MOE) controls the output enable signal. Global Bus/Switch Matrix The global bus contains all input and I/O pin signals as well as the buried feedback signal from all 32 macrocells. The switch matrix in each logic block receives as its inputs all signals from the global bus. Under software control, up to 40 of these signals can be selected as inputs to the logic block. Foldback Bus Each macrocell also generates a foldback product term. This signal goes to the regional bus and is available to four macrocells. The foldback is an inverse polarity of one of the macrocell’s product terms. The four foldback terms in each region allow generation of high fan-in sum terms (up to nine product terms) with little additional delay. Each I/O can be individually configured as an input, output, or for bi-directional operation. The output enable for each macrocell can be selected from the true or compliment of the two output enable pins, a subset of the I/O pins, or a subset of the I/O macrocells. This selection is automatically done by the fitter software when the I/O is configured as an input, all macrocell resources are still available, including the buried feedback, expander, and cascade logic. ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 4. Programmable Pin-keeper Option for Inputs and I/Os The ATF1502AS(L) offers the option of programming all input and I/O pins so the pin-keeper circuits can be utilized. When any pin is driven high or low and then subsequently left floating, it will stay at that previous high or low level. This circuitry prevents unused input and I/O lines from floating to intermediate voltage levels, which causes unnecessary power consumption and system noise. The keeper circuits eliminate the need for external pull-up resistors and eliminate their DC power consumption. Figure 4-1. Input Diagram VCC Input 100K ESD Protection Circuit Figure 4-2. Programmable Option I/O Diagram VCC OE Data I/O VCC 100K Programmable Option ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 7 5. Speed/Power Management The ATF1502AS(L) has several built-in speed and power management features. The ATF1502AS(L) contains circuitry which automatically puts the device into a low-power standby mode when no logic transitions are occurring. This not only reduces power consumption during inactive periods, but also provides proportional power savings for most applications running at system speeds below 50MHz. This feature may be selected as a design option. To further reduce power, each ATF1502AS(L) macrocell has a reduced-power bit feature. This feature allows individual macrocells to be configured for maximum power savings. This feature may be selected as a design option. The ATF1502AS(L) also has an optional power-down mode. In this mode, current drops to below 10mA. When the power-down option is selected, either PD1 or PD2 pins (or both) can be used to power down the part. The power-down option is selected in the design source file. When enabled, the device goes into power-down when either PD1 or PD2 is high. In the power-down mode, all internal logic signals are latched and held, as are any enabled outputs. All pin transitions are ignored until the PD pin is brought low. When the power-down feature is enabled, the PD1 or PD2 pin cannot be used as a logic input or output; however, the pin’s macrocell may still be used to generate buried foldback and cascade logic signals. All power-down AC characteristic parameters are computed from external input or I/O pins, with reduced-power bit turned on. For macrocells in reduced-power mode (reduced-power bit turned on), the reduced-power adder, tRPA, must be added to the AC parameters, which include the data paths tLAD, tLAC, tIC, tACL, tACH, and tSEXP. The ATF1502AS(L) macrocell also has an option whereby the power can be reduced on a per-macrocell basis. By enabling this power-down option, macrocells that are not used in an application can be turned down, thereby reducing the overall power consumption of the device. Each output also has individual slew rate control. This may be used to reduce system noise by slowing down outputs that do not need to operate at maximum speed. Outputs default to slow switching, and may be specified as fast switching in the design file. 6. Design Software Support ATF1502AS(L) designs are supported by several third-party tools. Automated fitters allow logic synthesis using a variety of high-level description languages and formats. 7. Power-up Reset The ATF1502AS(L) is designed with a power-up reset, a feature critical for state machine initialization. At a point delayed slightly from VCC crossing VRST, all registers will be initialized, and the state of each output will depend on the polarity of its buffer. However, due to the asynchronous nature of reset and uncertainty of how VCC actually rises in the system, the following conditions are required: The VCC rise must be monotonic, After reset occurs, all input and feedback setup times must be met before driving the clock pin high, and, The clock must remain stable during TD. The ATF1502AS(L) has two options for the hysteresis about the reset level, VRST, Small and Large. During the fitting process, users may configure the device with the Power-up Reset hysteresis set to Large or Small. Atmel POF2JED users may select the Large option by including the flag “-power_reset” on the command line after “filename.POF”. To allow the registers to be properly reinitialized with the Large hysteresis option selected, the following condition is added: If VCC falls below 2.0V, it must shut off completely before the device is turned on again. When the Large hysteresis option is active, ICC is reduced by several hundred micro amps as well. 8 ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 8. Security Fuse Usage A single fuse is provided to prevent unauthorized copying of the ATF1502AS(L) fuse patterns. Once programmed, fuse verify is inhibited; however, the 16-bit User Signature remains accessible. 9. Programming ATF1502AS(L) devices are In-System Programmable (ISP) devices utilizing the 4-pin JTAG protocol. This capability eliminates package handling normally required for programming and facilitates rapid design iterations and field changes. Atmel provides ISP hardware and software to allow programming of the ATF1502AS(L) via the PC. ISP is performed by using either a download cable, a comparable board tester, or a simple microprocessor interface. When using the ISP hardware or software to program the ATF1502AS(L) devices, four I/O pins must be reserved for the JTAG interface. However, the logic features that the macrocells have associated with these I/O pins are still available to the design for burned logic functions. To facilitate ISP programming by the Automated Test Equipment (ATE) vendors, Serial Vector Format (SVF) files can be created by Atmel-provided software utilities. ATF1502AS(L) devices can also be programmed using standard third-party programmers. With a third-party programmer, the JTAG ISP port can be disabled, thereby allowing four additional I/O pins to be used for logic. Contact your local Atmel representatives or Atmel PLD applications for details. 10. ISP Programming Protection The ATF1502AS(L) has a special feature which locks the device and prevents the inputs and I/O from driving if the programming process is interrupted for any reason. The inputs and I/O default to high-Z state during such a condition. In addition, the pin-keeper option preserves the previous state of the input and I/O PMS during programming. All ATF1502AS(L) devices are initially shipped in the erased state, thereby making them ready to use for ISP. Note: For more information refer to the “Designing for In-System Programmability with Atmel CPLDs” application note. ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 9 11. Electrical Characteristics 11.1 Absolute Maximum Ratings* Temperature Under Bias . . . . . . . . . . . . . . . . . -40°C to +85°C Storage Temperature . . . . . . . . . . . . . . . . . . . -65°C to +150°C Voltage on Any Pin with Respect to Ground . . . . . . . . . . . . . . . . . . . . . -2.0V to +7.0V(1) Voltage on Input Pins with Respect to Ground During Programming . . . . . . . . . . -2.0V to +14.0V(1) Programming Voltage with Respect to Ground . . . . . . . . . . . . . . . . . . . . -2.0V to +14.0V(1) Note: 11.2 1. Minimum voltage is -0.6VDC, which may undershoot to -2.0V for pulses of less than 20ns. Maximum output pin voltage is VCC + 0.75VDC, which may overshoot to 7.0V for pulses of less than 20ns. Pin Capacitance Table 11-1. Pin Capacitance(1) Typ Max Units Conditions CIN 8 10 pF VIN = 0V; f = 1MHz CI/O 8 10 pF VOUT = 0V; f = 1MHz Note: 11.3 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. The OGI pin (high-voltage pin during programming) has a maximum capacitance of 12pF. DC and AC Operating Conditions Table 11-2. DC and AC Operating Conditions Operating Temperature (Ambient) VCC (5.0V) Power Supply 10 *Notice: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 Commercial Industrial 0C to 70C -40C to 85C 5V± 5% 5V± 10% 11.4 DC Characteristics Table 11-3. DC Characteristics Symbol Parameter Condition IIL Input or I/O Low Leakage Current VIN = VCC IIH Input or I/O High Leakage Current IOZ Tri-state Output Off-state Current Min VO = VCC or GND Typ Max Units -2 -10 μA 2 10 -40 40 μA Com. 60 mA Ind. 75 mA Com. 10 μA Ind. 10 μA Std Mode Power Supply Current, Standby ICC1 VCC = Max VIN = 0, VCC “L” Mode ICC2 Power Supply Current, Power-down Mode VCC = Max VIN = 0, VCC “PD” Mode ICC3(2) Reduced-power Mode Supply Current, Standby VCC = Max VIN = 0, VCC Std Mode 1 5 mA Com. 35 mA Ind. 40 mA VIL Input Low Voltage -0.3 0.8 V VIH Input High Voltage 2.0 VCCIO + 0.3 V 3.0 0.45 V Output Low Voltage (TTL) VIN = VIH or VIL VCC = Min, IOL = 12mA Com. Ind. 0.45 Com. 0.2 V Ind. 0.2 V VOL Output Low Voltage (CMOS) VOH Notes: Output High Voltage (TTL) 1. 2. VIN = VIH or VIL VCC = Min, IOL = 0.1mA VIN = VIH or VIL VCC = Min, IOH = -4.0mA 2.4 V Not more than one output at a time should be shorted. Duration of short circuit test should not exceed 30s. ICC3 refers to the current in the reduced-power mode when macrocell reduced-power is turned on. ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 11 11.5 AC Characteristics Table 11-4. AC Characteristics(11.9) -7 Parameter tPD1 Input or Feedback to Non-registered Output tPD2 I/O Input or Feedback to Non-registered Feedback tSU Global Clock Setup Time 6 7 20 ns tH Global Clock Hold Time 0 0 0 ns tFSU Global Clock Setup Time of Fast Input 3 3 5 ns tFH Global Clock Hold Time of Fast Input 0.5 0.5 2 MHz tCOP Global Clock to Output Delay tCH Global Clock High Time 3 4 7 ns tCL Global Clock Low Time 3 4 7 ns tASU Array Clock Setup Time 3 3 5 ns tAH Array Clock Hold Time 2 3 6 ns tACOP Array Clock Output Delay tACH Array Clock High Time 3 4 10 ns tACL Array Clock Low Time 3 4 10 ns tCNT Minimum Clock Global Period fCNT Maximum Internal Global Clock Frequency tACNT Minimum Array Clock Period fACNT Maximum Internal Array Clock Frequency fMAX Maximum Clock Frequency tIN Input Pad and Buffer Delay 0.5 0.5 2 ns tIO I/O Input Pad and Buffer Delay 0.5 0.5 2 ns tFIN Fast Input Delay 1 1 2 ns tSEXP Foldback Term Delay 4 5 12 ns tPEXP Cascade Logic Delay 0.8 0.8 2 ns tLAD Logic Array Delay 3 5 8 ns tLAC Logic Control Delay 3 5 8 ns tIOE Internal Output Enable Delay 2 2 4 ns tOD1 Output Buffer and Pad Delay (Slow slew rate = OFF; VCC = 5.0V; CL = 35pF) 2 1.5 6 ns 12 1. 2. Max Min -25 Symbol Notes: Min -10 Max Min Max Units 7.5 10 25 ns 7 9 25 ns 4.5 5 7.5 10 8 125 13 25 10 100 8 22 50 10 ns ns ns MHz 22 ns 125 100 50 MHz 166.7 125 60 MHz See ordering information for valid part numbers. The tRPA parameter must be added to the tLAD, tLAC,tTIC, tACL, and tSEXP parameters for macrocells running in the reduced-power mode. ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 Table 11-4. AC Characteristics(11.9) (Continued) -7 Symbol Parameter Units tZX1 Output Buffer Enable Delay (Slow slew rate = OFF; VCCIO = 5.0V; CL = 35pF) 4.0 5.0 10 ns tZX2 Output Buffer Enable Delay (Slow slew rate = OFF; VCCIO = 3.3V; CL = 35pF) 4.5 5.5 10 ns tZX3 Output Buffer Enable Delay (Slow slew rate = ON; VCCIO = 5.0V/3.3V; CL = 35pF) 9 9 12 ns tXZ Output Buffer Disable Delay (CL = 5pF) 4 5 8 ns tSU Register Setup Time 3 3 6 ns tH Register Hold Time 2 3 6 ns tFSU Register Setup Time of Fast Input 3 3 3 ns tFH Register Hold Time of Fast Input 0.5 0.5 5 ns tRD Register Delay 1 2 2 ns tCOMB Combinatorial Delay 1 2 2 ns tIC Array Clock Delay 3 5 8 ns tEN Register Enable Time 3 5 8 ns tGLOB Global Control Delay 1 1 1 ns tPRE Register Preset Time 2 3 6 ns tCLR Register Clear Time 2 3 6 ns tUIM Switch Matrix Delay 1 1 2 ns tRPA Reduced-power Adder(2) 10 11 15 ns 1. 2. Max Min -25 Max Notes: Min -10 Max Min See ordering information for valid part numbers. The tRPA parameter must be added to the tLAD, tLAC,tTIC, tACL, and tSEXP parameters for macrocells running in the reduced-power mode. ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 13 11.6 Timing Model Figure 11-1. Timing Model Internal Output Enable Delay tIOE Global Control Delay tGLOB Input Delay tIN Logic Array Delay tLAD Switch Matrix tUIM Register Control Delay tLAC tIC tEN Foldback Term Delay tSEXP 11.7 Input Test Waveforms and Measurement Levels 3.0V AC Driving Levels 1.5V 0.0V Note: tR, tF = 1.5ns typical Output AC Test Loads Figure 11-3. Output AC Test Loads 5.0V R1 = 464Ω Output Pin R2 = 250Ω 14 Fast Input Delay tFIN Input Test Waveforms and Measurement Levels Figure 11-2. 11.8 Cascade Logic Delay tPEXP CL = 35pF ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 AC Measurement Level Register Delay tSU tH tPRE tCLR tRD tCOMB tFSU tFH Output Delay tOD1 tOD2 tOD3 tXZ tZX1 tZX2 tZX3 I/O Delay tIO 11.9 Power-down Mode The ATF1502AS(L) includes an optional pin-controlled power-down feature. When this mode is enabled, the PD pin acts as the power-down pin. When the PD pin is high, the device supply current is reduced to less than 5mA. During power-down, all output data and internal logic states are latched and held. Therefore, all registered and combinatorial output data remain valid. Any outputs that were in a high-Z state at the onset will remain at high-Z. During power-down, all input signals except the power-down pin are blocked. Input and I/O hold latches remain active to ensure the pins do not float to indeterminate levels, further reducing system power. The power-down pin feature is enabled in the logic design file. Designs using the power-down pin may not use the PD pin logic array input; however, all other PD pin macrocell resources may still be used, including the buried feedback and foldback product term array inputs. 11.9.1 Power-down AC Characteristics Table 11-5. Power-down AC Characteristics(1)(2) -7 Min -10 Symbol Parameter tIVDH Valid I, I/O before PD High 7 10 25 ns tGVDH Valid OE(2) before PD High 7 10 25 ns 7 10 25 ns (2) Min Max Min Max Units tCVDH Valid Clock tDHIX I, I/O Don’t Care after PD High 12 15 35 ns tDHGX OE(2) Don’t Care after PD High 12 15 35 ns tDHCX Clock(2) Don’t Care after PD High 12 15 35 ns tDLIV PD Low to Valid I, I/O 1 1 1 μs tDLGV PD Low to Valid OE (Pin or Term) 1 1 1 μs tDLCV PD Low to Valid Clock (Pin or Term) 1 1 1 μs tDLOV PD Low to Valid Output 1 1 1 μs Notes: 1. 2. before PD High Max -25 For slow slew outputs, add tSSO. Pin or product term. ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 15 12. JTAG-BST/ISP Overview The JTAG boundary-scan testing is controlled by the Test Access Port (TAP) controller in the ATF1502AS(L). The boundary-scan technique involves the inclusion of a shift-register stage (contained in a Boundary-Scan Cell) adjacent to each component so signals at component boundaries can be controlled and observed using scan testing methods. Each input pin and I/O pin has its own Boundary-Scan Cell (BSC) to support Boundary-Scan Testing (BST). The ATF1502AS(L) does not include a Test Reset (TRST) input pin because the TAP controller is automatically reset at power-up. The five JTAG modes supported include: SAMPLE/PRELOAD EXTEST BYPASS IDCODE HIGHZ The ATF1502AS(L) ISP can fully be described using JTAG’s BSDL as described in IEEE Standard 1149.1b. This allows ATF1502AS(L) programming to be described and implemented using any one of the third-party development tools supporting this standard. The ATF1502AS(L) has the option of using four JTAG-standard I/O pins for BST and ISP purposes. The ATF1502AS(L) is programmable through the four JTAG pins using the IEEE standard JTAG programming protocol established by IEEE Standard 1149.1 using 5V TTL-level programming signals from the ISP interface for in-system programming. The JTAG feature is a programmable option. If JTAG (BST or ISP) is not needed, then the four JTAG control pins are available as I/O pins. 13. JTAG Boundary-scan Cell (BSC) Testing The ATF1502AS(L) contains up to 32 I/O pins and four input pins, depending on the device type and package type selected. Each input pin and I/O pin has its own BSC in order to support BST as described in detail by IEEE Standard 1149.1. A typical BSC consists of three capture registers or scan registers and up to two update registers. There are two types of BSCs, one for input or I/O pin and one for the macrocells. The BSCs in the device are chained together through the capture registers. Input to the capture register chain is fed in from the TDI pin while the output is directed to the TDO pin. Capture registers are used to capture active device data signals, to shift data in and out of the device, and to load data into the update registers. Control signals are generated internally by the JTAG TAP controller. The BSC configuration for the input and I/O pins and macrocells is shown below. Figure 13-1. BSC Configuration for Input and I/O Pins (Except JTAG TAP Pins) Dedicated Input To Internal Logic 0 D 1 Q TDO Capture Registers Clock Shift TDI (From Next Register) Note: 16 1. The ATF1502AS(L) has a pull-up option on TMS and TDI pins. This feature is selected as a design option. ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 Figure 13-2. BSC Configuration for Macrocell TDO 0 Q D 1 TDI CLOCK TDO OEJ 0 0 1 D Q D Q 1 OUTJ 0 0 Pin 1 D Q D Q Capture DR Update DR 1 Mode TDI Shift Clock BSC for I/O Pins and Macrocells ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 17 14. PCI Compliance The ATF1502AS(L) supports the growing need in the industry to support the new Peripheral Component Interconnect (PCI) interface standard in PCI-based designs and specifications. The PCI interface calls for high current drivers, which are much larger than the traditional TTL drivers. In general, PLDs and FPGAs parallel outputs to support the high current load required by the PCI interface. The ATF1502AS(L) allows this without contributing to system noise while delivering low output to output skew. Having a programmable high drive option is also possible without increasing output delay or pin capacitance. Figure 14-1. PCI Voltage-to-current Curves for +5.0V Signaling in Pull-up Mode Figure 14-2. Pull Down Pull Up VCC VCC 2.2 DC drive point DC drive point 1.4 0.55 AC drive point -2 Test Point -44 Current (mA) -178 95 Current (mA) 380 3,6 PCI DC Characteristics Symbol Parameter Min Max Units VCC Supply Voltage 4.75 5.25 V VIH Input High Voltage 2.0 VCC + 0.5 V VIL Input Low Voltage -0.5 0.8 V IIH Input High Leakage Current(1) VIN = 2.7V 70 μA Conditions VIN = 0.5V -70 μA (1) IIL Input Low Leakage Current VOH Output High Voltage IOUT = -2mA VOL Output Low Voltage IOUT = 3mA, 6mA CIN 2.4 V 0.55 V Input Pin Capacitance 10 pF CCLK CLK Pin Capacitance 12 pF CIDSEL IDSEL Pin Capacitance 8 pF LPIN Pin Inductance 20 nH Note: 18 AC drive point Voltage Voltage Test Point 2.4 Table 14-1. PCI Voltage-to-current Curves for +5.0V Signaling in Pull-down Mode 1. Leakage current is with pin-keeper off. ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 Table 14-2. Symbol PCI AC Characteristics Parameter Switching Current High (Test High) IOH(AC) Conditions Min 0 < VOUT 1.4 -44 mA -44 + (VOUT - 1.4)/0.024 mA 1.4 < VOUT < 2.4 3.1 < VOUT < VCC VOUT = 3.1V VOUT >2.2V Switching Current Low (Test Point) IOL(AC) 2.2 > VOUT > 0 Max Units Equation A mA -142 μA 95 mA VOUT/0.023 mA 0.1 > VOUT > 0 VOUT = 0.71 Equation B mA 206 mA ICL Low Clamp Current -5 < VIN -1 SLEWR Output Rise Slew Rate 0.4V to 2.4V Load 1 5 V/ns SLEWF Output Fall Slew Rate 2.4V to 0.4V Load 1 5 V/ns Notes: 1. 2. -25 + (VIN + 1)/0.015 mA Equation A: IOH = 11.9 (VOUT - 5.25) * (VOUT + 2.45) for VCC > VOUT > 3.1V. Equation B: IOL = 78.5 * VOUT * (4.4 - VOUT) for 0V < VOUT < 0.71V. ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 19 15. Pinouts 15.1 ATF1502AS(L) Dedicated Pinouts 44-lead TQFP 44-lead J-lead INPUT/OE2/GCLK2 40 2 INPUT/GCLR 39 1 INPUT/OE1 38 44 INPUT/GCLK1 37 43 I/O / GCLK3 35 41 I/O / PD (1,2) 5, 19 11, 25 I/O / TDI (JTAG) 1 7 I/O / TMS (JTAG) 7 13 I/O / TCK (JTAG) 26 32 I/O / TDO (JTAG) 32 38 GND 4, 16, 24, 36 10, 22, 30, 42 VCC 9, 17, 29, 41 3, 15, 23, 35 # of Signal Pins 36 36 # User I/O Pins 32 32 Dedicated Pin Note: 20 OE (1, 2) . . . . . . . . . . . . . GCLR . . . . . . . . . . . . . . . GCLK (1, 2, 3) . . . . . . . . . PD (1, 2) . . . . . . . . . . . . . TDI, TMS, TCK, TDO . . . GND . . . . . . . . . . . . . . . . VCC . . . . . . . . . . . . . . . . . Global OE pins Global Clear pin Global Clock pins Power-down pins JTAG pins used for boundary-scan testing or in-system programming Ground pins VCC pins for the device (+5V) ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 15.2 ATF1502AS(L) I/O Pinouts MC PLC 44-lead PLCC 44-lead TQFP 1 A 4 42 2 A 5 43 3 A/PD1 6 44 4/TDI A 7 1 5 A 8 2 6 A 9 3 7 A 11 5 8 A 12 6 9/TMS A 13 7 10 A 14 8 11 A 16 10 12 A 17 11 13 A 18 12 14 A 19 13 15 A 20 14 16 A 21 15 17 B 41 35 18 B 40 34 19 B 39 33 20/TDO B 38 32 21 B 37 31 22 B 36 30 23 B 34 28 24 B 33 27 25/TCK B 32 26 26 B 31 25 27 B 29 23 28 B 28 22 29 B 27 21 30 B 26 20 31 B 25 19 32 B 24 18 ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 21 22 ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 23 24 ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 16. Ordering Information 16.1 Green Package Options (Pb/Halide-free/RoHS Compliant) tPD (ns) tCO1 (ns) fMAX (MHz) 7.5 4.5 166.7 10 5 125 25 13 60 Ordering Code Package ATF1502AS-7AX44 44A ATF1502AS-7JX44 44J ATF1502AS-10AU44 44A ATF1502AS-10JU44 44J ATF1502ASL-25AU44 44A ATF1502ASL-25JU44 44J Operation Range Commercial (0C to 70C) Industrial (-40C to +85C) Industrial (-40C to +85C) Package Type 44A 44-lead, Thin Plastic Gull Wing Quad Flatpack Package (TQFP) 44J 44-lead, Plastic J-leaded Chip Carrier OTP (PLCC) ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 25 17. Packaging Information 17.1 44A — 44-lead TQFP D1 D e E E1 b BOTTOM VIEW TOP VIEW C 0°~7° A1 L A2 A SIDE VIEW COMMON DIMENSIONS (Unit of Measure = mm) Notes: 1. This package conforms to JEDEC reference MS-026, Variation ACB. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum plastic body size dimensions including mold mismatch. 3. Lead coplanarity is 0.10 mm maximum. SYMBOL MIN NOM MAX A – – 1.20 A1 0.05 – 0.15 A2 0.95 1.00 1.05 D 11.75 12.00 12.25 D1 9.90 10.00 10.10 E 11.75 12.00 12.25 E1 9.90 10.00 10.10 B 0.30 – 0.45 C 0.09 – 0.20 L 0.45 – 0.75 e NOTE Note 2 Note 2 0.80 TYP 1/10/13 Package Drawing Contact: [email protected] 26 ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 TITLE 44A, 44-lead 10.0 x 10.0x1.0 mm Body, 0.80 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) GPC DRAWING NO. REV. AIX 44A D 17.2 44J — 44-lead PLCC 1.14(0.045) X 45° PIN NO. 1 1.14(0.045) X 45° 0.318(0.0125) 0.191(0.0075) IDENTIFIER E1 E D2/E2 B1 B e A2 D1 A1 D A 0.51(0.020)MAX 45° MAX (3X) COMMON DIMENSIONS (Unit of Measure = mm) Notes: 1. This package conforms to JEDEC reference MS-018, Variation AC. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010"(0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102 mm) maximum. SYMBOL MIN NOM MAX A 4.191 – 4.572 A1 2.286 – 3.048 A2 0.508 – – D 17.399 – 17.653 D1 16.510 – 16.662 E 17.399 – 17.653 E1 16.510 – 16.662 D2/E2 14.986 – 16.002 B 0.660 – 0.813 B1 0.330 – 0.533 e NOTE Note 2 Note 2 1.270 TYP 10/04/01 DRAWING NO. REV. TITLE Package Drawing Contact: [email protected] 44J, 44-lead, Plastic J-leaded Chip Carrier (PLCC) 44J ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 B 27 18. 28 Revision History Revision Date 0995L 03/2014 0995K 06/2005 Comments Remove lead based package offering and 15ns speed grade. Update template, logos, and disclaimer page. Green package options added. ATF1502AS(L) [DATASHEET] Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014 XXXXXX Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 | www.atmel.com © 2014 Atmel Corporation. / Rev.: Atmel-0995L-CPLD-ATF1502AS(L)-Datasheet_032014. Atmel®, Atmel logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical Applications”) without an Atmel officer's specific written consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons systems. Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.