20 MHz to 500 MHz IF Gain Block ADL5534 Preliminary Technical Data FEATURES 14 GND 13 GND 15 GND 16 GND FUNCTIONAL BLOCK DIAGRAM 12 RFOUT1 RFIN1 1 ADL5534 11 CLIN1 10 RFOUT2 9 CLIN2 GND 5 RFIN2 3 NC 4 GND 7 GND 8 NC 2 GND 6 Fixed gain of 20 dB Operation up to 500 MHz +41.8 dBm OIP3 at 70 MHz Noise Figure 2.5 dB at 70 MHz Temperature and power supply stable Power supply: 5 V Power supply current: 90 mA per amplifier 1000 V ESD (Class 1C) Figure 1. Block Diagram GENERAL DESCRIPTION The ADL5534 contains two broadband, fixed-gain, linear amplifiers in an 4x4 mm LFCSP package and operates at frequencies up to 500 MHz. The device can be used in a wide variety of wired and wireless devices including cellular, GSM and WCDMA, and broadband applications. The ADL5534 has a fixed gain 20 dB and is stable over frequency, temperature, power supply and from device to device. It achieves an OIP3 of 41.8 dBm with an output compression point of +20.2 dBm and a noise figure of 2.5 dB. The ADL5534 is single-ended and internally matched to 50 Ω with an input return loss of 10 dB. Only input/output ac- coupling capacitors, a power supply decoupling capacitor and external inductor are required for operation. This IF amplifier operates with supply voltage of +5V, consuming 90 mA of supply current per amplifier. Fabricated on a GaAs HBT process and has an ESD rating of 1000 V (Class 1C). The device is packaged in a 4mm x 4mm LFCSP that uses an exposed paddle for excellent thermal impedance and operates from −40°C to +85°C. A fully populated evaluation board is available. Rev. PrD 5/07 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2007 Analog Devices, Inc. All rights reserved. ADL5534 Preliminary Technical Data TABLE OF CONTENTS Features .............................................................................................. 1 ESD Caution...................................................................................4 Functional Block Diagram .............................................................. 1 Pin Configuration and Function Descriptions..............................5 General Description ......................................................................... 1 Typical Performance Characteristics ..............................................6 Revision History ............................................................................... 2 EVALUATION BOARD ...................................................................7 Specifications..................................................................................... 3 OUTLINE DIMENSIONS ...............................................................9 Absolute Maximum Ratings............................................................ 4 ORDERING GUIDE.....................................................................9 REVISION HISTORY 5/07—Rev. PrD: Preliminary Version Rev. PrD 5/07 | Page 2 of 9 Preliminary Technical Data ADL5534 SPECIFICATIONS VCC = 5 V, T = 25°C, unless otherwise noted. Table 1. Parameter OVERALL FUNCTION Frequency Range Gain vs. Frequency Input Return Loss (S11) Output Return Loss (S22) Isolation (RFIN1 to RFOUT2 and RFIN2 to RFOUT1) Isolation (RFIN1 to RFOUT2 and RFIN2 to RFOUT1) FREQUENCY = 70 MHz Gain vs. Temperature Output 1 dB Compression Point Output Third-Order Intercept Noise Figure FREQUENCY = 190 MHz Gain vs. Temperature Output 1 dB Compression Point Output Third-Order Intercept Noise Figure FREQUENCY = 380 MHz Gain vs. Temperature Output 1 dB Compression Point Output Third-Order Intercept Noise Figure POWER INTERFACE Supply Voltage Supply Current vs. Temperature Power Dissipation Conditions Min Typ 20 Max Unit 500 ± 50 MHz. Center Frequency = 190 MHz or 380 MHz 30 MHz to 500 MHz 30 MHz to 500 MHz Frequency = 200 MHz ±0.15 -10 -10 -29.8 MHz dB dB dB dB Frequency = 500 MHz -22.5 dB 19.8 ±.25 20.0 41.8 2.5 dB dB dBm dBm dB 19.4 ±.25 20.2 40.1 2.7 dB dB dBm dBm dB 18.8 ±.25 20.1 37.0 2.9 dB dB dBm dBm dB −40°C ≤ TA ≤ +85°C ∆f = 1 MHz, Output Power (POUT) = 0 dBm (per tone) −40°C ≤ TA ≤ +85°C ∆f = 1 MHz, Output Power (POUT) = 0 dBm (per tone) −40°C ≤ TA ≤ +85°C ∆f = 1 MHz, Output Power (POUT) = 0 dBm (per tone) Pins RFOUT, Vcc 4.75 Current Consumption is Specified Per Amplifier −40°C ≤ TA ≤ +85°C (Specified Per Amplifier) VPOS = 5V (Specified Per Amplifier) Rev. PrD 5/07 | Page 3 of 9 5 90 104 450 5.25 V mA mA mW ADL5534 Preliminary Technical Data ABSOLUTE MAXIMUM RATINGS Table 2. Parameter Supply Voltage, VPOS Input Power Per Amplifier(re: 50 Ω) Internal Power Dissipation Per Amplifier (Paddle Soldered) θJA (Paddle Soldered) Maximum Junction Temperature Operating Temperature Range Storage Temperature Range (Soldering 60 sec) Rating 5.5 V +12 dBm 650 mW TBD °C/W 150 °C −40°C to +85°C −65°C to +150°C 240°C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION Rev. PrD 5/07 | Page 4 of 9 Preliminary Technical Data ADL5534 14 GND 13 GND 15 GND 16 GND PIN CONFIGURATION AND FUNCTION DESCRIPTIONS PIN 1 INDICATOR RFIN1 1 TOP VIEW (Not to Scale) GND 5 NC 4 12 RFOUT1 11 CLIN1 10 RFOUT2 9 CLIN2 GND 8 RFIN2 3 GND 7 ADL5534 GND 6 NC 2 Figure 2. Table 3. Pin Function Descriptions Pin No. 1, 3 10, 12 5, 6, 7,8, 13,14,15,16 2, 4 9, 11 Mnemonic RFIN1, RFIN2 RFOUT1, RFOUT2 GND Description RF Input: Requires a DC blocking capacitor. Use a 10 nF capacitor for normal operation. RF Output and Bias: DC bias is provided to this pin through an inductor. A 470 nH inductor is recommended for normal operation. RF path requires a DC blocking capacitor. Use a 10 nF capacitor for normal operation. Ground. Connect this pin to a low impedance ground plane. NC CLIN1, CLIN2 No Connect. A 1 nF capacitor connected between 9 and ground an Pin11 and ground provides decoupling for the on board linearizer. Internally connected to GND. Solder to a low impedance ground plane Exposed Paddle Rev. PrD 5/07 | Page 5 of 9 ADL5534 Preliminary Technical Data TYPICAL PERFORMANCE CHARACTERISTICS 45.0 40.0 0 -2 -4 -6 30.0 ReturnLoss & Isolation (dB) NF, GAIN,P1dB, OIP3 (dB, dBm) 35.0 25.0 20.0 15.0 NF GAIN P1dB OIP3 10.0 S11 dB -8 S12 dB -10 -12 S22 dB -14 -16 -18 -20 -22 -24 5.0 -26 -28 0.0 -30 0 100 200 300 400 500 600 0 Frequency (MHz) 46 44 42 40 OIP3 - dBm 38 36 34 3B_20MHz_5V 3B_70MHz_5V 3B_190MHz_5V 3B_380MHz_5V 3B_500MHz_5V 28 26 24 22 -6 -4 -2 0 2 4 6 8 10 300 400 500 600 Figure 5 ADL5534 Input / Output Return Loss and Reverse Isolation vs Frequency 48 30 200 Freq (MHz) Figure 3 ADL5534 Gain, Noise Figure, OIP3 and P1dB vs Frequency 32 100 12 14 16 18 20 Pout (dBm) Figure 4 ADL5534 OIP3 vs Pout and Frequency Rev. PrD 5/07 | Page 6 of 9 Preliminary Technical Data ADL5534 EVALUATION BOARD corresponding to RFIN2 – RFOUT2 To bias both amplifiers from a single supply, connect 5V to Vpos or Vpos1 and attach a jumper across W3 Figure 6 shows the schematic for the ADL5531 evaluation board. The board is powered by a single 5 V supply. The components used on the board are listed in. Table 4Applying 5V to Vpos will bias the amplifier corresponding to RFIN1 RFOUT2. Applying 5 V toVpos1 will bias the amplifier Vpos C7 10 nF C9 W1 Gnd 1 uF L1 470 nH NC NC NC NC C5 1 nF CLIN2 NC NC C6 1 nF 8 6 7 5 W3 R8 Open C14 Open 9 Vpos1 R4 Open C4 10nF L2 470 nH Vpos R6 Open T2 ADT2-1T-1P C16 open RFOUT2 RFIN2 NC 4 C3 10nF 12 Z1 CLIN1 11 ADL5534 10 NC NC 3 RFOUT1 NC C12 Open RFIN1 R2 Open C13 Open 13 2 14 Open 15 R7 ADT2-1T-1P open R3 open 1 C15 T1 RFIN2 C11 Open R1 open R5 open 16 C1 10nF RFIN1 C2 10nF Vpos1 C8 10 nF C10 1 uF W2 Gnd Figure 6. Evaluation Board Schematic Table 4. Evaluation Board Configuration Options Component C1, C2, C3, C4 C5, C6 R1, R2, R3, R4, R5, R6, R7 R8 T1, T2 C11, C12, C13, C14, C15, C16 Function AC-coupling capacitors. Provides decoupling for the on board linearizer. Optional components used for Configuring ADL5534 as a balanced amplifier. Default Value 10 nF 0402 1 nF 0603 Open 0603 T1 and T2 are 50 Ω t o100 Ω impedance transformers used to configure the ADL5534 as a balanced amplifier. T1 and T2 are used to present a 100 Ω differential impedance to the ADL5534. Optional components used for Configuring ADL5534 as a balanced amplifier. MiniCircuits ADT2-1T-1P Open C9, C10 C7, C8 L1, L2 VCC & GND Power Supply decoupling capacitors capacitor. Power Supply decoupling capacitors capacitor. DC bias inductor. Clip-on terminals for power supply. W1,W2 W3 2-pin jumper for connection of ground and supply via cable. 2-pin jumper use to connect Vpos to Vpos1 Rev. PrD 5/07 | Page 7 of 9 C11-C14: Open 0402 C15,C16: Open 0402 1 uF 0603 10 nF 0603 470 nH 1008CS VCC Red GND Black Open ADL5534 Preliminary Technical Data Figure 7. Evaluation Board Layout (Top) Figure 8. Evaluation Board Layout (Bottom) Rev. PrD 5/07 | Page 8 of 9 Preliminary Technical Data ADL5534 OUTLINE DIMENSIONS 4.00 BSC SQ 0.60 MAX 12 PIN 1 INDICATOR 3.75 BSC SQ TOP VIEW 12° MAX 13 9 1.95 BCS 0.80 MAX 0.65 TYP 8 5 PIN 1 INDICATOR 1 16 EXPOSED PAD 0.65 BSC 4 2.65 2.50 SQ 2.35 0.25 MIN BOTTOM VIEW 0.05 MAX 0.02 NOM COPLANARITY 0.20 REF 0.08 0.30 0.23 0.18 COMPLIANT TO JEDEC STANDARDS MO-220-VGGC. 031006-A 1.00 0.85 0.80 SEATING PLANE 0.50 0.40 0.30 Figure 9. 16-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 4mm × 4 mm Body, Very Thin, Quad Lead CP-16-13 Dimensions shown in millimeters ORDERING GUIDE Model Temperature Range Package Description Package Option 1 −40°C to +85°C 8-Lead LFCSP Tape and Reel CP-16-13 ADL5534ACPZ-WP −40°C to +85°C 8-Lead LFCSP Waffle Pack CP-16-13 ADL5534ACPZ-R7 ADL5534-EVALZ 1 1 Evaluation Board Z = Pb-free part. ©2007 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. PR06836-0-5/07(PrD) Rev. PrD 5/07 | Page 9 of 9 Branding Ordering Quantity