AWL005G - AWL10G AVALANCHE GLASS PASSIVATED BRIDGE RECTIFIERS PRV : 50 - 1000 Volts Io : 1.0 Ampere WOB 0.39 (10.0) 0.31 (7.87) FEATURES : Glass passivated chip High case dielectric strength High surge current capability High reliability Low reverse current Low forward voltage drop Ideal for printed circuit board 0.22 (5.59) 0.18 (4.57) + - AC 1.00 (25.4) MIN. 1.10 (27.9) MIN. * * * * * * * 0.034 (0.86) 0.028 (0.71) MECHANICAL DATA : * Case : Reliable low cost construction utilizing molded plastic technique * Epoxy : UL94V-O rate flame retardant * Terminals : Plated leads solderable per MIL-STD-202, Method 208 guaranteed * Polarity : Polarity symbols marked on case * Mounting position : Any * Weight : 1.29 grams AC + - 0.22 (5.59) 0.18 (4.57) AC 0.22 (5.59) 0.18 (4.57) Dimension in inches and (millimeter) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. RATING Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Minimum Avalanche Breakdown Voltage at 100 µA Maximum Avalanche Breakdown Voltage at 100 µA Maximum Average Forward Current 0.375" (9.5 mm) lead length Tc = 50°C Peak Forward Surge Current Single half sine wave Superimposed on rated load (JEDEC Method) Rating for fusing ( t < 8.3 ms. ) Maximum Forward Voltage per Diode at IF = 1.0 Amp. Maximum DC Reverse Current Ta = 25 °C at Rated DC Blocking Voltage Ta = 100 °C Typical Junction Capacitance per Diode (Note 1) Typical Thermal Resistance (Note 2) Operating Junction Temperature Range Storage Temperature Range SYMBOL VRRM VRMS VDC VBO(min.) VBO(max.) AWL AWL 005G 01G 50 100 35 70 50 100 100 150 550 600 AWL 02G 200 140 200 250 700 AWL 04G 400 280 400 450 900 AWL 06G 600 420 600 700 1150 AWL 08G 800 560 800 900 1350 AWL 10G 1000 700 1000 1100 1550 UNIT Volts Volts Volts Volts Volts IF(AV) 1.0 Amps. IFSM 30 10 1.2 10 1.0 24 36 - 50 to + 150 - 50 to + 150 Amps. I2t VF IR IR(H) CJ RθJA TJ TSTG Notes : 1 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts. 2 ) Thermal resistance from Junction to Ambient at 0.375" (9.5 mm) lead length P.C. Board mounting. A2S Volts µA mA pf °C/W °C °C UPDATE : APRIL 23,1998 RATING AND CHARACTERISTIC CURVES ( AWL005G - AWL10G ) FIG.1 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT FIG.2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 30 PC Board 0.375(9.5mm) 0.8 Copper Pads 0.22" x 0.22" (5.5 x5.5mm) 0.6 0.4 0.2 60 Hz, Resistive or Inductive load. 0 0 25 50 75 100 125 150 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES 1.0 24 18 12 SINGLE HALF SINE WAVE (JEDEC METHOD) 6 0 175 TJ = 55 °C 1 CASE TEMPERATURE, ( °C) 20 10 1 TJ = 25 °C Pulse Width = 300 µs 1 % Duty Cycle 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 FORWARD VOLTAGE, VOLTS 4 6 10 20 40 60 100 FIG.4 - TYPICAL REVERSE CHARACTERISTICS REVERSE CURRENT, MICROAMPERES FORWARD CURRENT, AMPERES FIG.3 - TYPICAL FORWARD CHARACTERISTICS 0.1 2 NUMBER OF CYCLES AT 60Hz 1.8 10 TJ = 100 °C 1.0 TJ = 25 °C 0.1 0.01 0 20 40 60 80 100 120 PERCENT OF RATED REVERSE VOLTAGE, (%) 140