TI LMV824PWRE4 Low-voltage rail-to-rail output operational amplifier Datasheet

LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
FEATURES
•
•
•
•
•
•
•
2.5-V, 2.7-V, and 5-V Performance
–40°C to 125°C Operation
No Crossover Distortion
Low Supply Current at VCC+ = 5 V:
– LMV821…0.3 mA Typ
– LMV822…0.5 mA Typ
– LMV824…1 mA Typ
Rail-to-Rail Output Swing
Gain Bandwidth of 5.5 MHz Typ at 5 V
Slew Rate of 1.9 V/µs Typ at 5 V
DESCRIPTION/ORDERING INFORMATION
The LMV821 single, LMV822 dual, and LMV824 quad
devices are low-voltage (2.5 V to 5.5 V), low-power
commodity
operational
amplifiers.
Electrical
characteristics are very similar to the LMV3xx
operational amplifiers (low supply current, rail-to-rail
outputs, input common-mode range that includes
ground). However, the LMV8xx devices offer a higher
bandwidth (5.5 MHz typical) and faster slew rate
(1.9 V/µs typical).
The LMV8xx devices are cost-effective solutions for
applications
requiring
low-voltage/low-power
operation and space-saving considerations. The
LMV821 is available in the ultra-small DCK package,
which is approximately half the size of SOT-23-5. The
DCK package saves space on printed circuit boards
and enables the design of small portable electronic
devices (cordless and cellular phones, laptops, PDAs,
PCMIA). It also allows the designer to place the
device closer to the signal source to reduce noise
pickup and increase signal integrity.
SLOS434G – FEBRUARY 2004 – REVISED AUGUST 2005
LMV824 . . . D, DGV, OR PW PACKAGE
(TOP VIEW)
1OUT
1IN−
1IN+
VCC+
2IN+
2IN−
2OUT
1
14
2
13
3
12
4
11
5
10
6
9
7
8
4OUT
4IN−
4IN+
GND/VCC−
3IN+
3IN−
3OUT
LMV822 . . . D OR DGK PACKAGE
(TOP VIEW)
1OUT
1IN −
1IN+
GND/VCC−
1
8
2
7
3
6
4
5
VCC+
2OUT
2IN −
2IN+
LMV821 . . . DBV OR DCK PACKAGE
(TOP VIEW)
IN+
GND/VCC−
IN−
1
5
VCC+
4
OUT
2
3
The LMV8xx devices are characterized for operation
from –40°C to 85°C. The LMV8xxI devices are
characterized for operation from –40°C to 125°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2004–2005, Texas Instruments Incorporated
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434G – FEBRUARY 2004 – REVISED AUGUST 2005
ORDERING INFORMATION
PACKAGE (1)
TA
SC-70 – DCK
Single
SOT-23 – DBV
SOIC – D
–40°C to 85°C
Dual
MSOP/VSSOP – DGK
SOIC – D
Quad
TSSOP – PW
TVSOP – DGV
SC-70 – DCK
Single
SOT-23 – DBV
SOIC – D
–40°C to 125°C
Dual
MSOP/VSSOP – DGK
SOIC – D
Quad
TSSOP – PW
TVSOP – DGV
(1)
(2)
2
ORDERABLE PART NUMBER
Reel of 3000
LMV821DCKR
Reel of 250
LMV821DCKT
Reel of 3000
LMV821DBVR
Reel of 250
LMV821DBVT
Tube of 75
LMV822D
Reel of 2500
LMV822DR
Tube of 100
LMV822DGK
Reel of 2500
LMV822DGKR
Tube of 50
LMV824D
Reel of 2500
LMV824DR
Tube of 90
LMV824PW
Reel of 2000
LMV824PWR
Reel of 2000
LMV824DGVR
Reel of 3000
LMV821IDCKR
Reel of 250
LMV821IDCKT
Reel of 3000
LMV821IDBVR
Reel of 250
LMV821IDBVT
Tube of 75
LMV822ID
Reel of 2500
LMV822IDR
Tube of 100
LMV822IDGK
Reel of 2500
LMV822IDGKR
Tube of 50
LMV824ID
Reel of 2500
LMV824IDR
Tube of 90
LMV824IPW
Reel of 2000
LMV824IPWR
Reel of 2000
LMV824IDGVR
TOP-SIDE MARKING (2)
RY_
RB8_
MV822
RA_
LMV824
MV824
MV824
RZ_
RB1_
MV822I
R8_
LMV824I
MV824I
MV824I
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
DBV/DCK/DGK: The actual top-side marking has one additional character that designates the assembly/test site.
www.ti.com
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
SLOS434G – FEBRUARY 2004 – REVISED AUGUST 2005
SYMBOL (EACH AMPLIFIER)
−
IN −
OUT
+
IN +
LMV824 SIMPLIFIED SCHEMATIC
VCC
VBIAS1
+
VCC
−
VBIAS2
VBIAS5
+
+
Output
−
VCC VCC
−
VBIAS3
+
IN−
IN+
VBIAS4−
+
−
3
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434G – FEBRUARY 2004 – REVISED AUGUST 2005
Absolute Maximum Ratings (1)
over operating free-air temperature range (unless otherwise noted)
MIN
VCC
Supply voltage (2)
VID
Differential input voltage (3)
VI
Input voltage range (either input)
Duration of output short circuit (one amplifier) to ground (4)
VCC–
At or below TA = 25°C, VCC ≤ 5.5 V
D package
θJA
Package thermal impedance (5) (6)
TJ
Operating virtual junction temperature
Tstg
Storage temperature range
(1)
(2)
(3)
(4)
(5)
(6)
MAX
UNIT
5.5
V
±VCC
V
VCC+
V
Unlimited
8 pin
97
14 pin
86
DBV package
206
DCK package
252
DGK package
172
DGV package
127
PW package
113
–65
°C/W
150
°C
150
°C
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating
conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values (except differential voltages and VCC specified for the measurement of IOS) are with respect to the network GND.
Differential voltages are at IN+ with respect to IN–.
Short circuits from outputs to VCC can cause excessive heating and eventual destruction.
Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = (TJ(max) – TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
The package thermal impedance is calculated in accordance with JESD 51-7.
Recommended Operating Conditions
VCC
TA
4
MIN
MAX
2.5
5
LMV8xxI
–40
125
LMV8xx
–40
85
Supply voltage (single-supply operation)
Operating free-air temperature
UNIT
V
°C
www.ti.com
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
SLOS434G – FEBRUARY 2004 – REVISED AUGUST 2005
LMV8xx 2.5-V Electrical Characteristics
VCC+ = 2.5 V, VCC– = 0 V, VIC = 1 V, VO = 1.25 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
VIO
TEST CONDITIONS
TA
25°C
Input offset voltage
TYP
MAX
1
3.5
–40°C to 85°C
High level
VCC+ = 2.5 V, RL = 600 Ω to 1.25 V
Low level
VO
LMV8xx
MIN
Output swing
High level
VCC+ = 2.5 V, RL = 2 kΩ to 1.25 V
Low level
4
25°C
2.3
–40°C to 85°C
2.2
25°C
0.13
0.2
0.3
2.4
–40°C to 85°C
2.3
25°C
mV
2.37
–40°C to 85°C
25°C
UNIT
2.46
0.08
–40°C to 85°C
V
0.12
0.2
LMV8xxI 2.5-V Electrical Characteristics
VCC+ = 2.5 V, VCC– = 0 V, VIC = 1 V, VO = 1.25 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
VIO
TEST CONDITIONS
TA
25°C
Input offset voltage
TYP
MAX
1
3.5
–40°C to 125°C
High level
VCC+ = 2.5 V, RL = 600 Ω to 1.25 V
Low level
VO
LMV8xxI
MIN
Output swing
High level
VCC+ = 2.5 V, RL = 2 kΩ to 1.25 V
Low level
5.5
25°C
2.28
–40°C to 125°C
2.18
25°C
0.13
–40°C to 125°C
2.28
25°C
–40°C to 125°C
0.22
0.32
2.38
mV
2.37
–40°C to 125°C
25°C
UNIT
2.46
0.08
V
0.14
0.22
5
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434G – FEBRUARY 2004 – REVISED AUGUST 2005
LMV8xx 2.7-V Electrical Characteristics
VCC+ = 2.7 V, VCC– = 0 V, VIC = 1 V, VO = 1.35 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Average temperature coefficient
of input offset voltage
IIB
Input bias current
IIO
Input offset current
CMRR Common-mode rejection ratio
TEST CONDITIONS
TA
LMV8xx
MIN
25°C
1
25°C
30
–40°C to 85°C
25°C
0.5
–40°C to 85°C
VIC = 0 to 1.7 V
25°C
70
68
75
–40°C to 85°C
70
–kSVR
Negative supply-voltage
rejection ratio
VCC+ = 1.7 V, VCC– = –1 V to –3.3 V,
VO = 0, VIC = 0
25°C
73
–40°C to 85°C
70
VICR
Common-mode input
voltage range
CMRR ≥ 50 dB
RL = 600 Ω to 1.35 V,
VO = 1.35 V to 2.2 V
Sourcing
RL = 600 Ω to 1.35 V,
VO = 1.35 V to 0.5 V
Sinking
RL = 2 kΩ to 1.35 V,
VO = 1.35 V to 2.2 V
Sourcing
RL = 2 kΩ to 1.35 V,
VO = 1.35 V to 0.5 V
Sinking
High level
VCC+ = 2.7 V,
RL = 600 Ω to 1.35 V
Low level
Output swing
High level
VCC+ = 2.7 V,
RL = 2 kΩ to 1.35 V
Output current
Low level
ICC
Supply current
100
25°C
90
–40°C to 85°C
85
25°C
85
–40°C to 85°C
80
25°C
95
90
–40°C to 85°C
85
25°C
2.5
–40°C to 85°C
2.4
25°C
2.58
0.13
2.6
–40°C to 85°C
2.5
25°C
2.66
0.08
–40°C to 85°C
V
0.12
0.2
12
16
VO = 2.7 V
Sinking
25°C
12
26
0.22
–40°C to 85°C
mA
0.3
0.5
0.45
–40°C to 85°C
25°C
0.2
0.3
25°C
–40°C to 85°C
dB
95
25°C
LMV822 (both amplifiers)
V
100
–40°C to 85°C
25°C
dB
90
25°C
25°C
nA
90
Sourcing
LMV824 (all four amplifiers)
6
–0.3
to 2
nA
dB
85
–0.2
to 1.9
mV
dB
85
VO = 0 V
LMV821
30
85
25°C
–40°C to 85°C
90
50
–40°C to 85°C
UNIT
µV/°C
140
25°C
IO
3.5
25°C
VCC+ = 1.7 V to 4 V, VCC– = –1 V,
VO = 0, VIC = 0
VO
1
4
Positive supply-voltage
rejection ratio
Large-signal voltage
amplification
MAX
–40°C to 85°C
+kSVR
AV
TYP
0.6
0.8
0.72
1
1.2
mA
www.ti.com
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
SLOS434G – FEBRUARY 2004 – REVISED AUGUST 2005
LMV8xx 2.7-V Electrical Characteristics (continued)
VCC+ = 2.7 V, VCC– = 0 V, VIC = 1 V, VO = 1.35 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
Slew rate (1)
SR
25°C
LMV8xx
MIN
TYP
MAX
UNIT
1.7
V/µs
GBW
Gain bandwidth product
(2)
25°C
5
MHz
Φm
Phase margin
(2)
25°C
60
deg
Gain margin
(2)
25°C
8.6
dB
V (3)
Amplifier-to-amplifier isolation
VCC+ = 5 V, RL = 100 kΩ to 2.5
25°C
135
dB
Vn
Equivalent input noise voltage
f = 1 kHz, VIC = 1 V
25°C
45
nV/√Hz
In
Equivalent input noise current
f = 1 kHz
25°C
0.18
pA/√Hz
Total harmonic distortion
f = 1 kHz, AV = –2, RL = 10 kΩ,
VO = 4.1 Vp-p
25°C
0.01
%
THD
(1)
(2)
(3)
Connected as voltage follower with 1-V step input. Value specified is the slower of the positive and negative slew rates.
40-dB closed-loop dc gain, CL = 22 pF
Each amplifier excited in turn with 1 kHz to produce VO = 3 Vp-p
7
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434G – FEBRUARY 2004 – REVISED AUGUST 2005
LMV8xxI 2.7-V Electrical Characteristics
VCC+ = 2.7 V, VCC– = 0 V, VIC = 1 V, VO = 1.35 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Average temperature coefficient
of input offset voltage
IIB
Input bias current
IIO
Input offset current
CMRR Common-mode rejection ratio
TEST CONDITIONS
TA
LMV8xxI
MIN
25°C
1
25°C
30
–40°C to 125°C
25°C
0.5
–40°C to 125°C
VIC = 0 to 1.7 V
25°C
70
68
75
–40°C to 125°C
70
–kSVR
Negative supply-voltage
rejection ratio
VCC+ = 1.7 V, VCC– = –1 V to –3.3 V,
VO = 0, VIC = 0
25°C
73
–40°C to 125°C
70
VICR
Common-mode input
voltage range
CMRR ≥ 50 dB
RL = 600 Ω to 1.35 V,
VO = 1.35 V to 2.2 V
Sourcing
RL = 600 Ω to 1.35 V,
VO = 1.35 V to 0.5 V
Sinking
RL = 2 kΩ to 1.35 V,
VO = 1.35 V to 2.2 V
Sourcing
RL = 2 kΩ to 1.35 V,
VO = 1.35 V to 0.5 V
Sinking
High level
VCC+ = 2.7 V,
RL = 600 Ω to 1.35 V
Low level
Output swing
High level
VCC+ = 2.7 V,
RL = 2 kΩ to 1.35 V
Output current
Low level
ICC
Supply current
100
25°C
90
–40°C to 125°C
85
25°C
85
–40°C to 125°C
80
25°C
95
–40°C to 125°C
90
25°C
90
–40°C to 125°C
85
25°C
2.5
–40°C to 125°C
2.4
25°C
2.5
25°C
2.66
0.08
–40°C to 125°C
V
0.12
0.2
12
16
VO = 2.7 V
Sinking
25°C
12
26
0.22
–40°C to 125°C
mA
0.3
0.5
0.45
–40°C to 125°C
25°C
0.2
0.3
–40°C to 125°C
–40°C to 125°C
dB
2.58
25°C
LMV822 (both amplifiers)
V
95
0.13
2.6
25°C
dB
100
–40°C to 125°C
25°C
nA
90
Sourcing
LMV824 (all four amplifiers)
8
–0.3
to 2
nA
dB
85
–0.2
to 1.9
mV
dB
85
25°C
25°C
30
85
VO = 0 V
LMV821
90
50
–40°C to 125°C
UNIT
µV/°C
140
25°C
IO
3.5
25°C
VCC+ = 1.7 V to 4 V, VCC– = –1 V,
VO = 0, VIC = 0
VO
1
5.5
Positive supply-voltage
rejection ratio
Large-signal voltage
amplification
MAX
–40°C to 125°C
+kSVR
AV
TYP
0.6
0.8
0.72
1
1.2
mA
www.ti.com
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
SLOS434G – FEBRUARY 2004 – REVISED AUGUST 2005
LMV8xxI 2.7-V Electrical Characteristics (continued)
VCC+ = 2.7 V, VCC– = 0 V, VIC = 1 V, VO = 1.35 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
Slew rate (1)
SR
25°C
LMV8xxI
MIN
TYP
MAX
UNIT
1.7
V/µs
GBW
Gain bandwidth product
(2)
25°C
5
MHz
Φm
Phase margin
(2)
25°C
60
deg
Gain margin
(2)
25°C
8.6
dB
V (3)
Amplifier-to-amplifier isolation
VCC+ = 5 V, RL = 100 kΩ to 2.5
25°C
135
dB
Vn
Equivalent input noise voltage
f = 1 kHz, VIC = 1 V
25°C
45
nV/√Hz
In
Equivalent input noise current
f = 1 kHz
25°C
0.18
pA/√Hz
Total harmonic distortion
f = 1 kHz, AV = –2, RL = 10 kΩ,
VO = 4.1 Vp-p
25°C
0.01
%
THD
(1)
(2)
(3)
Connected as voltage follower with 1-V step input. Value specified is the slower of the positive and negative slew rates.
40-dB closed-loop dc gain, CL = 22 pF
Each amplifier excited in turn with 1 kHz to produce VO = 3 Vp-p
9
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434G – FEBRUARY 2004 – REVISED AUGUST 2005
LMV8xx 5-V Electrical Characteristics
VCC+ = 5 V, VCC– = 0 V, VIC = 2 V, VO = 2.5 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Average temperature coefficient
of input offset voltage
IIB
Input bias current
IIO
Input offset current
CMRR Common-mode rejection ratio
TEST CONDITIONS
TA
LMV8xx
MIN
25°C
1
25°C
40
–40°C to 85°C
25°C
0.5
–40°C to 85°C
VIC = 0 to 4 V
25°C
72
70
75
–40°C to 85°C
70
–kSVR
Negative supply-voltage
rejection ratio
VCC+ = 1.7 V, VCC– = –1 V to –3.3 V,
VO = 0, VIC = 0
25°C
73
–40°C to 85°C
70
VICR
Common-mode input
voltage range
CMRR ≥ 50 dB
RL = 600 Ω to 2.5 V,
VO = 2.5 V to 4.5 V
Sourcing
RL = 600 Ω to 2.5 V,
VO = 2.5 V to 0.5 V
Sinking
RL = 2 kΩ to 2.5 V,
VO = 2.5 V to 4.5 V
Sourcing
RL = 2 kΩ to 2.5 V,
VO = 2.5 V to 0.5 V
Sinking
High level
VCC+ = 5 V,
RL = 600 Ω to 2.5 V
Low level
Output swing
High level
VCC+ = 5 V,
RL = 2 kΩ to 2.5 V
Low level
VO = 0 V
Sourcing
VO = 5 V
Sinking
Output current
LMV821
ICC
Supply current
LMV822 (both amplifiers)
LMV824 (all four amplifiers)
10
105
25°C
95
–40°C to 85°C
90
25°C
95
–40°C to 85°C
90
25°C
95
95
–40°C to 85°C
90
25°C
4.75
–40°C to 85°C
4.7
25°C
V
dB
105
105
4.84
0.17
0.25
0.3
25°C
4.85
–40°C to 85°C
4.8
25°C
4.9
0.1
–40°C to 85°C
V
0.15
0.2
25°C
20
–40°C to 85°C
15
25°C
20
–40°C to 85°C
15
45
mA
40
0.3
–40°C to 85°C
0.4
0.6
0.5
–40°C to 85°C
–40°C to 85°C
dB
105
–40°C to 85°C
25°C
nA
90
25°C
25°C
nA
dB
85
–0.3
to 4.3
mV
dB
85
–0.2
to 4.2
25°C
30
90
25°C
–40°C to 85°C
100
50
–40°C to 85°C
UNIT
µV/°C
150
25°C
IO
3.5
25°C
VCC+ = 1.7 V to 4 V, VCC– = –1 V,
VO = 0, VIC = 0
VO
1
4
Positive supply-voltage
rejection ratio
Large-signal voltage
amplification
MAX
–40°C to 85°C
+kSVR
AV
TYP
0.7
0.9
1
0.3
1.5
mA
www.ti.com
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
SLOS434G – FEBRUARY 2004 – REVISED AUGUST 2005
LMV8xx 5-V Electrical Characteristics (continued)
VCC+ = 5 V, VCC– = 0 V, VIC = 2 V, VO = 2.5 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
SR
Slew rate
TEST CONDITIONS
TA
VCC+ = 5 V (1)
25°C
LMV8xx
MAX
UNIT
MIN
TYP
1.4
1.9
V/µs
GBW
Gain bandwidth product
(2)
25°C
5.5
MHz
Φm
Phase margin
(2)
25°C
64.2
deg
Gain margin
(2)
25°C
8.7
dB
V (3)
Amplifier-to-amplifier isolation
VCC+ = 5 V, RL = 100 kΩ to 2.5
25°C
135
dB
Vn
Equivalent input noise voltage
f = 1 kHz, VIC = 1 V
25°C
42
nV/√Hz
In
Equivalent input noise current
f = 1 kHz
25°C
0.2
pA/√Hz
Total harmonic distortion
f = 1 kHz, AV = –2, RL = 10 kΩ,
VO = 4.1 Vp-p
25°C
0.01
%
THD
(1)
(2)
(3)
Connected as voltage follower with 3-V step input. Value specified is the slower of the positive and negative slew rates.
40-dB closed-loop dc gain, CL = 22 pF
Each amplifier excited in turn with 1 kHz to produce VO = 3 Vp-p
11
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434G – FEBRUARY 2004 – REVISED AUGUST 2005
LMV8xxI 5-V Electrical Characteristics
VCC+ = 5 V, VCC– = 0 V, VIC = 2 V, VO = 2.5 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Average temperature coefficient
of input offset voltage
IIB
Input bias current
IIO
Input offset current
CMRR Common-mode rejection ratio
TEST CONDITIONS
TA
LMV8xxI
MIN
25°C
1
25°C
40
–40°C to 125°C
25°C
0.5
–40°C to 125°C
VIC = 0 to 4 V
25°C
72
70
75
–40°C to 125°C
70
–kSVR
Negative supply-voltage
rejection ratio
VCC+ = 1.7 V, VCC– = –1 V to –3.3 V,
VO = 0, VIC = 0
25°C
73
–40°C to 125°C
70
VICR
Common-mode input
voltage range
CMRR ≥ 50 dB
RL = 600 Ω to 2.5 V,
VO = 2.5 V to 4.5 V
Sourcing
RL = 600 Ω to 2.5 V,
VO = 2.5 V to 0.5 V
Sinking
RL = 2 kΩ to 2.5 V,
VO = 2.5 V to 4.5 V
Sourcing
RL = 2 kΩ to 2.5 V,
VO = 2.5 V to 0.5 V
Sinking
High level
VCC+ = 5 V,
RL = 600 Ω to 2.5 V
Low level
Output swing
High level
VCC+ = 5 V,
RL = 2 kΩ to 2.5 V
Low level
VO = 0 V
Sourcing
VO = 5 V
Sinking
Output current
LMV821
ICC
Supply current
LMV822 (both amplifiers)
LMV824 (all four amplifiers)
12
105
25°C
95
–40°C to 125°C
90
25°C
95
–40°C to 125°C
90
25°C
95
–40°C to 125°C
90
25°C
95
–40°C to 125°C
90
25°C
4.75
–40°C to 125°C
4.6
25°C
4.8
25°C
dB
105
4.84
0.25
4.9
0.1
–40°C to 125°C
V
0.15
0.2
25°C
20
–40°C to 125°C
15
25°C
20
–40°C to 125°C
15
45
mA
40
0.3
–40°C to 125°C
0.4
0.6
0.5
–40°C to 125°C
–40°C to 125°C
V
0.3
–40°C to 125°C
25°C
dB
105
0.17
4.85
nA
105
–40°C to 125°C
25°C
nA
dB
85
–0.3
to 4.3
mV
dB
85
–0.2
to 4.2
25°C
30
90
25°C
25°C
100
50
–40°C to 125°C
UNIT
µV/°C
150
25°C
IO
3.5
25°C
VCC+ = 1.7 V to 4 V, VCC– = –1 V,
VO = 0, VIC = 0
VO
1
5.5
Positive supply-voltage
rejection ratio
Large-signal voltage
amplification
MAX
–40°C to 125°C
+kSVR
AV
TYP
0.7
0.9
1
1.3
1.5
mA
www.ti.com
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
SLOS434G – FEBRUARY 2004 – REVISED AUGUST 2005
LMV8xxI 5-V Electrical Characteristics (continued)
VCC+ = 5 V, VCC– = 0 V, VIC = 2 V, VO = 2.5 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
SR
Slew rate
TEST CONDITIONS
TA
VCC+ = 5 V (1)
25°C
LMV8xxI
MAX
UNIT
MIN
TYP
1.4
1.9
V/µs
GBW
Gain bandwidth product
(2)
25°C
5.5
MHz
Φm
Phase margin
(2)
25°C
64.2
deg
Gain margin
(2)
25°C
8.7
dB
V (3)
Amplifier-to-amplifier isolation
VCC+ = 5 V, RL = 100 kΩ to 2.5
25°C
135
dB
Vn
Equivalent input noise voltage
f = 1 kHz, VIC = 1 V
25°C
42
nV/√Hz
In
Equivalent input noise current
f = 1 kHz
25°C
0.2
pA/√Hz
Total harmonic distortion
f = 1 kHz, AV = –2, RL = 10 kΩ,
VO = 4.1 Vp-p
25°C
0.01
%
THD
(1)
(2)
(3)
Connected as voltage follower with 3-V step input. Value specified is the slower of the positive and negative slew rates.
40-dB closed-loop dc gain, CL = 22 pF
Each amplifier excited in turn with 1 kHz to produce VO = 3 Vp-p
13
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434G – FEBRUARY 2004 – REVISED AUGUST 2005
TYPICAL CHARACTERISTICS
TA = 25°C, VCC+ = 5-V Single Supply (Unless Otherwise Noted)
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
1200
INPUT CURRENT
vs
TEMPERATURE
−30
LMV824
All Channels
VCC+ = 5 V
Vin = VCC+/2
TA = 85C
−40
II − Input Current − nA
ICC − Supply Current − µA
1000
TA = 25C
800
600
TA = −40C
400
−50
−60
200
−70
−40
0
0
1
2
3
4
VCC+ − Supply Voltage − V
5
6
80
100
0.01
0.1
1
Output Voltage Referenced to V+ − (V)
10
Figure 2.
SOURCING CURRENT
vs
OUTPUT VOLTAGE
SOURCING CURRENT
vs
OUTPUT VOLTAGE
100
VCC+ = 2.7 V
VCC+ = 5 V
10
IO − Source Current − mA
IO − Source Current − mA
0
20
40
60
TA − Temperature − °C
Figure 1.
100
1
0.1
0.01
0.001
0.01
0.1
1
Output Voltage Referenced to V+ − (V)
Figure 3.
14
−20
10
10
1
0.1
0.01
0.001
Figure 4.
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434G – FEBRUARY 2004 – REVISED AUGUST 2005
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V Single Supply (Unless Otherwise Noted)
SINKING CURRENT
vs
OUTPUT VOLTAGE
SINKING CURRENT
vs
OUTPUT VOLTAGE
100
100
VCC+ = 2.7 V
VCC+ = 5 V
10
IO − Sink Current − mA
IO − Sink Current − mA
10
1
1
0.1
0.1
0.01
0.01
0.1
0.01
1
10
Figure 5.
Figure 6.
OUTPUT VOLTAGE SWING
vs
SUPPLY VOLTAGE
OUTPUT VOLTAGE SWING
vs
SUPPLY VOLTAGE
RL = 2 kΩ to Mid Rail
Output Voltage From Supply Voltage − mV
Output Voltage From Supply Voltage − mV
10
80
RL = 10 kΩ to Mid Rail
40
30
Negative Swing
20
0
2.6
1
Output Voltage Referenced to GND − V
50
10
0.1
0.01
Output Voltage Referenced to GND − V
Positive Swing
3
3.4
3.8
4.2
VCC+ − Supply Voltage − V
Figure 7.
4.6
5
70
60
50
Negative Swing
40
Positive Swing
30
20
10
0
2.6
3
3.4
3.8
4.2
VCC+ − Supply Voltage − V
4.6
5
Figure 8.
15
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434G – FEBRUARY 2004 – REVISED AUGUST 2005
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V Single Supply (Unless Otherwise Noted)
OUTPUT VOLTAGE SWING
vs
SUPPLY VOLTAGE
160
RL = 600 Ω to Mid Rail
Output Voltage From Supply Voltage − mV
Output Voltage From Supply Voltage − mV
160
OUTPUT VOLTAGE SWING
vs
LOAD RESISTANCE
150
140
Negative Swing
130
120
110
Positive Swing
100
90
80
70
60
2.6
RlL = 5 kΩ to Mid Rail
VCC+ = 5 V
140
120
100
80
60
40
20
0
3
3.4
3.8
4.2
4.6
100
5
VCC+ − Supply Voltage − V
1000
10k
Resistive Load − Ω
Figure 9.
Figure 10.
CROSSTALK REJECTION
vs
FREQUENCY
+PSRR
vs
FREQUENCY
100
160
100k
VCC = 2.5 V
90
150
140
70
VCC = 1.35 V
PSRR − dB
Crosstalk Rejection − dB
80
130
120
110
100
90
100
50
40
30
VCC+ = ±2.5 V
VI = 3 VPP
RL = 5 kΩ
AV = 1
20
10
1k
10k
Frequency − Hz
Figure 11.
16
60
100k
0
100
1k
10k
Frequency − Hz
Figure 12.
100k
1M
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434G – FEBRUARY 2004 – REVISED AUGUST 2005
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V Single Supply (Unless Otherwise Noted)
–PSRR
vs
FREQUENCY
100
VCC = 2.5 V
90
80
PSRR − dB
70
60 VCC = 1.35 V
50
40
30
20
10
0
100
1k
10k
100k
Frequency − Hz
1M
Figure 13.
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 2.7 V, RL = 600 Ω, 2 kΩ, 100 kΩ)
80
140
Gain − dB
Phase
60
100
50
80
40
60
30
40
Gain
20
20
0
10
VCC+ = 2.7 V
600 Ω
2 kΩ
100 kΩ
0
−10
−20
−40
−20
1k
Phase Margin − Deg
120
70
10k
100k
1M
−60
10M
Frequency − Hz
Figure 14.
17
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434G – FEBRUARY 2004 – REVISED AUGUST 2005
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V Single Supply (Unless Otherwise Noted)
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 5 V, RL = 600 Ω, 2 kΩ, 100 kΩ)
80
140
70
120
100
Phase
50
80
40
60
30
40
20
20
Gain
0
10
−10
−20
−20
VCC+ = 5 V
600 Ω
2 kΩ
100 kΩ
0
1k
Phase Margin − Deg
Gain − dB
60
−40
10k
100k
Frequency − Hz
1M
−60
10M
Figure 15.
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 2.7 V, RL = 10 kΩ, CL = 22 pF, 100 pF, 200 pF)
80
100
70
Gain − dB
60
60
50
40
40
20
30
0
20
−20
Gain
−40
10
VCC+ = 2.7 V
RL = 10 kΩ
22 pF
100 pF
200 pF
0
−10
−60
−80
−20
1k
10k
100k
Frequency − Hz
Figure 16.
18
1M
−100
10M
Phase Margin − Deg
80
Phase
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434G – FEBRUARY 2004 – REVISED AUGUST 2005
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V Single Supply (Unless Otherwise Noted)
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 5 V, RL = 10 kΩ, CL = 22 pF, 100 pF, 200 pF)
80
100
70
80
Phase
60
50
40
40
20
0
30
Gain
−20
20
10
0
−10
−20
−40
VCC+ = 5 V
RL = 10 kΩ
22 pF
100 pF
200 pF
1k
Phase Margin − Deg
Gain − dB
60
−60
−80
10k
100k
1M
−100
10M
Frequency − Hz
Figure 17.
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 2.7 V, RL = 600 Ω, CL = 22 pF, 100 pF, 200 pF)
80
140
70
120
Phase
100
50
80
40
60
30
40
20
20
Gain
VCC+ = 2.7 V
RL = 600 Ω
10
0
−20
22 pF
100 pF
200 pF
−10
−20
0
1k
Phase Margin − Deg
Gain − dB
60
−40
10k
100k
1M
−60
10M
Frequency − Hz
Figure 18.
19
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434G – FEBRUARY 2004 – REVISED AUGUST 2005
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V Single Supply (Unless Otherwise Noted)
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 5 V, RL = 600 Ω, CL = 22 pF, 100 pF, 200 pF)
80
140
70
120
Phase
100
50
80
40
60
40
30
Gain
20
20
10
0
−20
22 pF
100 pF
200 pF
−10
−20
0
VCC+ = 5 V
RL = 600 Ω
1k
−40
10k
100k
Frequency − Hz
Figure 19.
20
1M
−60
10M
Phase Margin − Deg
Gain − dB
60
PACKAGE OPTION ADDENDUM
www.ti.com
26-Oct-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
LMV821DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821DBVRE4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821DBVTE4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821DCKR
ACTIVE
SC70
DCK
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821DCKRE4
ACTIVE
SC70
DCK
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821DCKT
ACTIVE
SC70
DCK
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821DCKTE4
ACTIVE
SC70
DCK
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821IDBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821IDBVRE4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821IDBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821IDBVTE4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821IDCKR
ACTIVE
SC70
DCK
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821IDCKRE4
ACTIVE
SC70
DCK
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821IDCKT
ACTIVE
SC70
DCK
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821IDCKTE4
ACTIVE
SC70
DCK
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822D
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822DE4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822DGKR
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822DR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822DRE4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822ID
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822IDE4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822IDGKR
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822IDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Addendum-Page 1
Lead/Ball Finish
MSL Peak Temp (3)
PACKAGE OPTION ADDENDUM
www.ti.com
26-Oct-2005
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
LMV822IDRE4
ACTIVE
SOIC
D
8
LMV824D
ACTIVE
SOIC
D
14
50
LMV824DE4
ACTIVE
SOIC
D
14
50
LMV824DGVR
ACTIVE
TVSOP
DGV
LMV824DGVRE4
ACTIVE
TVSOP
LMV824DR
ACTIVE
LMV824DRE4
2500 Green (RoHS &
no Sb/Br)
Lead/Ball Finish
MSL Peak Temp (3)
CU NIPDAU
Level-1-260C-UNLIM
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
DGV
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824ID
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824IDE4
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824IDGVR
ACTIVE
TVSOP
DGV
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824IDGVRE4
ACTIVE
TVSOP
DGV
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824IDR
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824IDRE4
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824IPW
ACTIVE
TSSOP
PW
14
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824IPWE4
ACTIVE
TSSOP
PW
14
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824IPWR
ACTIVE
TSSOP
PW
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824IPWRE4
ACTIVE
TSSOP
PW
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824PW
ACTIVE
TSSOP
PW
14
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824PWE4
ACTIVE
TSSOP
PW
14
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824PWR
ACTIVE
TSSOP
PW
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824PWRE4
ACTIVE
TSSOP
PW
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS &
http://www.ti.com/productcontent for the latest availability information and additional product content details.
Addendum-Page 2
no
Sb/Br)
-
please
check
PACKAGE OPTION ADDENDUM
www.ti.com
26-Oct-2005
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 3
MECHANICAL DATA
MPDS006C – FEBRUARY 1996 – REVISED AUGUST 2000
DGV (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
24 PINS SHOWN
0,40
0,23
0,13
24
13
0,07 M
0,16 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
0°–8°
1
0,75
0,50
12
A
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,08
14
16
20
24
38
48
56
A MAX
3,70
3,70
5,10
5,10
7,90
9,80
11,40
A MIN
3,50
3,50
4,90
4,90
7,70
9,60
11,20
DIM
4073251/E 08/00
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side.
Falls within JEDEC: 24/48 Pins – MO-153
14/16/20/56 Pins – MO-194
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2005, Texas Instruments Incorporated