MOTOROLA MMA6260 ±1.5g dual axis micromachined accelerometer Datasheet

MMA6260Q
Rev. 2, 10/2004
Freescale Semiconductor
Technical Data
±1.5g Dual Axis
Micromachined Accelerometer
MMA6260Q
MMA6261Q
MMA6262Q
MMA6263Q
The MMA6200 series of low cost capacitive micromachined accelerometers
feature signal conditioning, a 1-pole low pass filter and temperature compensation. Zero-g offset full scale span and filter cut-off are factory set and require
no external devices. A full system self-test capability verifies system functionality.
Features
•
•
•
•
•
•
•
•
•
•
High Sensitivity
Low Noise
Low Power
2.7 V to 3.6 V Operation
6mm x 6mm x 1.98 mm QFN
Integral Signal Conditioning with Low Pass Filter
Linear Output
Ratiometric Performance
Self-Test
Robust Design, High Shocks Survivability
MMA6260Q Series: X-Y AXIS SENSITIVITY
MICROMACHINED ACCELEROMETER
±1.5 g
Bottom View
Typical Applications
•
•
•
•
•
•
•
Tilt Monitoring
Position & Motion Sensing
Freefall Detection
Impact Monitoring
Appliance Control
Vibration Monitoring and Recording
Smart Portable Electronics
16 LEAD QFN
CASE 1477-01
ORDERING INFORMATION
Pin Assignment
Top View
50 Hz
1.2 mA
1477-01
QFN-16, Tube
MMA6260QR2
50 Hz
1.2 mA
1477-01
QFN-16,Tape & Reel
MMA6261Q
300 Hz
1.2 mA
1477-01
QFN-16, Tube
N/C
1
12 ST
N/C
N/C
Package
N/C
MMA6260Q
Case No.
YOUT
IDD
XOUT
Device Name
Bandwidth
Response
16 15 14 13
QFN-16,Tape & Reel
2
11
N/C
1477-01
QFN-16,Tube
VDD 3
10
N/C
MMA6262QR2
150 Hz
2.2 mA
1477-01
QFN-16,Tape & Reel
VSS 4
9
N/C
MMA6263Q
900 Hz
2.2 mA
1477-01
QFN-16, Tube
MMA6263QR2
900 Hz
2.2 mA
1477-01
QFN-16,Tape & Reel
© Freescale Semiconductor, Inc., 2004. All rights reserved.
5
6
7
8
N/C
1477-01
2.2 mA
N/C
1.2 mA
150 Hz
N/C
300 Hz
MMA6262Q
N/C
MMA6261QR2
VDD
G-CELL
SENSOR
ST
SELF-TEST
X-INTEGRATOR
X-GAIN
CONTROL LOGIC &
EEPROM TRIM CIRCUITS
Y-INTEGRATOR
X-FILTER
OSCILLATOR
Y-GAIN
Y-FILTER
X-TEMP
COMP
XOUT
CLOCK GEN
Y-TEMP
COMP
YOUT
VSS
Figure 1. Simplified Accelerometer Functional Block Diagram
MAXIMUM RATINGS (Maximum ratings are the limits to which the device can be exposed without causing permanent damage.)
Rating
Symbol
Value
Unit
gmax
±2000
g
Supply Voltage
VDD
-0.3 to +3.6
V
Test1
Ddrop
1.2
m
Tstg
-40 to +125
°C
Maximum Acceleration (all axis)
Drop
Storage Temperature Range
Note:
1. Dropped onto concrete surface from any axis.
ELECTRO STATIC DISCHARGE (ESD)
WARNING: This device is sensitive to electrostatic
discharge.
Although the Freescale Semiconductor accelerometers contain internal 2000 V ESD protection circuitry, extra precaution must be taken by the user to protect the
chip from ESD. A charge of over 2000 volts can accumulate on the human body or associated test equipment. A
charge of this magnitude
can alter the performance or cause failure of the chip.
When handling the accelerometer, proper ESD precautions should be followed to avoid exposing the device to
discharges which may be detrimental to its performance.
MMA6200 SERIES
2
Sensor Device Data
Freescale Semiconductor
Operating Characteristics
Unless otherwise noted: -20°C < TA < 85°C, 3.0 V < VDD < 3.6 V, Acceleration = 0g, Loaded output1
Characteristic
Symbol
Min
Typ
Max
Unit
VDD
2.7
3.3
3.6
V
IDD
IDD
TA
gFS
—
—
-20
—
1.2
2.2
—
1.5
1.5
3.0
+85
—
mA
mA
°C
g
VOFF
1.485
—
1.65
VOFF, TA
1.815
—
S
S, TA
740
—
2.0
800
0.015
f_3dB
f_3dB
f_3dB
f_3dB
NLOUT
—
—
—
—
-1.0
nRMS
nRMS
nRMS
nRMS
Operating Range2
Supply Voltage3
Supply Current
MMA6260Q, MMA6261Q
MMA6262Q, MMA6263Q
Operating Temperature Range
Acceleration Range
Output Signal
Zero g (TA = 25°C, VDD = 3.3 V)4
Zero g
Sensitivity (TA = 25°C, VDD = 3.3 V)
Sensitivity
Bandwidth Response
MMA6260Q
MMA6261Q
MMA6262Q
MMA6263Q
Nonlinearity
Noise
MMA6260Q RMS (0.1 Hz – 1 kHz)
MMA6261Q RMS (0.1 Hz – 1 kHz)
MMA6262Q RMS (0.1 Hz – 1 kHz)
MMA6263Q RMS (0.1 Hz – 1 kHz)
Power Spectral Density RMS (0.1 Hz – 1 kHz)
MMA6260Q, MMA6261Q
MMA6262Q, MMA6263Q
Self-Test
Output Response
Input Low
Input High
Pull-Down Resistance5
Response Time6
Output Stage Performance
Full-Scale Output Range (IOUT = 200 µA)
Capacitive Load Drive7
Output Impedance
Power-Up Response Time
MMA6260Q
MMA6261Q
MMA6262Q
MMA6263Q
Mechanical Characteristics
Transverse Sensitivity8
V
860
—
mg/°C
mV/g
%/°C
50
300
150
900
—
—
—
—
—
+1.0
Hz
Hz
Hz
Hz
% FSO
—
—
—
—
1.8
3.5
1.3
2.5
—
—
—
—
mVrms
nPSD
nPSD
—
—
300
200
—
—
ug/√Hz
VST
VIL
VIH
RPO
0.9 VDD
VDD
0.3 VDD
VDD
43
—
—
—
57
71
V
V
V
kΩ
tST
—
2.0
—
ms
VFSO
CL
ZO
VSS +0.25
—
—
50
VDD -0.25
—
—
100
300
V
pF
Ω
tRESPONSE
tRESPONSE
tRESPONSE
tRESPONSE
—
—
—
—
14
2.0
4.0
0.7
—
—
—
—
ms
ms
ms
ms
VZX, YX, ZY
-5.0
—
+5.0
% FSO
—
0.7 VDD
Notes:
1. For a loaded output, the measurements are observed after an RC filter consisting of a 1.0 kΩ resistor and a 0.1 µF capacitor to ground.
2. These limits define the range of operation for which the part will meet specification.
3. Within the supply range of 2.7 and 3.6 V, the device operates as a fully calibrated linear accelerometer. Beyond these supply limits the device
may operate as a linear device but is not guaranteed to be in calibration.
4. The device can measure both + and - acceleration. With no input acceleration the output is at midsupply. For positive acceleration the output
will increase above VDD/2. For negative acceleration, the output will decrease below VDD/2.
5. The digital input pin has an internal pull-down resistance to prevent inadvertent self-test initiation due to external board level leakages.
6. Time for the output to reach 90% of its final value after a self-test is initiate.
7. Preserves phase margin (60°) to guarantee output amplifier stability.
8. A measure of the device’s ability to reject an acceleration applied 90° from the true axis of sensitivity.
MMA6200 SERIES
Sensor Device Data
Freescale Semiconductor
3
PRINCIPLE OF OPERATION
The Freescale Semiconductor accelerometer is a surfacemicromachined integrated-circuit accelerometer.
The device consists of a surface micromachined capacitive
sensing cell (g-cell) and a signal conditioning ASIC contained in
a single integrated circuit package. The sensing element is
sealed hermetically at the wafer level using a bulk micromachined cap wafer.
The g-cell is a mechanical structure formed from semiconductor materials (polysilicon) using semiconductor processes
(masking and etching). It can be modeled as a set of beams attached to a movable central mass that move between fixed
beams. The movable beams can be deflected from their rest
position by subjecting the system to an acceleration (Figure 2).
As the beams attached to the central mass move, the distance from them to the fixed beams on one side will increase by
the same amount that the distance to the fixed beams on the
other side decreases. The change in distance is a measure of
acceleration.
The g-cell plates form two back-to-back capacitors
(Figure 2). As the center plate moves with acceleration, the distance between the plates changes and each capacitor's value
will change, (C = Aε/D). Where A is the area of the plate,
ε is the dielectric constant, and D is the distance between
the plates.
The ASIC uses switched capacitor techniques to measure
the g-cell capacitors and extract the acceleration data from the
difference between the two capacitors. The ASIC also signal
conditions and filters (switched capacitor) the signal, providing
a high level output voltage that is ratiometric and proportional to
acceleration.
Acceleration
SPECIAL FEATURES
Filtering
These Freescale Semiconductor accelerometers contain an
onboard single-pole switched capacitor filter. Because the filter
is realized using switched capacitor techniques, there is no requirement for external passive components (resistors and capacitors) to set the cut-off frequency.
Self-Test
The sensor provides a self-test feature allowing the verification of the mechanical and electrical integrity of the accelerometer at any time before or after installation. A fourth plate is used
in the g-cell as a self-test plate. When a logic high input to the
self-test pin is applied, a calibrated potential is applied across
the self-test plate and the moveable plate. The resulting electrostatic force (Fe = 1/2 AV2/d2) causes the center plate to deflect.
The resultant deflection is measured by the accelerometer's
ASIC and a proportional output voltage results. This procedure
assures both the mechanical (g-cell) and electronic sections of
the accelerometer are functioning.
Freescale Semiconductor accelerometers include fault detection circuitry and a fault latch. Parity of the EEPROM bits becomes odd in number.
Self-test is disabled when EEPROM parity error occurs.
Ratiometricity
Ratiometricity simply means the output offset voltage and
sensitivity will scale linearly with applied supply voltage. That is,
as supply voltage is increased, the sensitivity and offset increase linearly; as supply voltage decreases, offset and sensitivity decrease linearly. This is a key feature when interfacing to
a microcontroller or an A/D converter because it provides system level cancellation of supply induced errors in the analog to
digital conversion process.
Figure 2. Simplified Transducer Physical Model
MMA6200 SERIES
4
Sensor Device Data
Freescale Semiconductor
16 15 14 13
N/C
1
12 ST
N/C
2
11
N/C
7
8
N/C
9
N/C
VSS 4
N/C
N/C
N/C
10
6
Pin No.
Pin
Name
Description
1, 5 - 7, 13, 16
N/C
14
YOUT
Output voltage of the accelerometer. Y
Direction.
15
XOUT
Output voltage of the accelerometer. X
Direction.
3
VDD
Power supply input.
4
VSS
The power supply ground.
2, 8 - 11
N/C
Used for factory trim.
Leave unconnected.
12
ST
Logic input pin used to initiate
self-test.
No internal connection.
Leave unconnected.
MMA6260Q
Series
3
VDD
0.1 µF
YOUT
14
1 kΩ
0.1 µF
4
12
R
1 kΩ
YOUT
VSS
R
1 kΩ
A/D IN
C 0.1 µF
A/D IN
C 0.1 µF
C 0.1 µF
VDD
VSS
C 0.1 µF
VDD
VRH
C 0.1 µF
POWER SUPPLY
Figure 3. Pinout Description
VDD
XOUT
N/C
VDD 3
5
P0
ST
MICROCONTROLLER
N/C
YOUT
N/C
XOUT
Top View
ACCELEROMETER
BASIC CONNECTIONS
Figure 5. Recommend PCB Layout for Interfacing
Accelerometer to Microcontroller
Notes:
1. Use 0.1 µF capacitor on VDD to decouple the power
source.
2. Physical coupling distance of the accelerometer to the
microcontroller should be minimal.
3. Flag underneath package is connected to ground.
4. Place a ground plane beneath the accelerometer to
reduce noise, the ground plane should be attached to all
of the open ended terminals shown in Figure 5.
5. Use an RC filter with 1.0 kΩ and 0.1 µF on the outputs of
the accelerometer to minimize clock noise (from the
switched capacitor filter circuit).
6. PCB layout of power and ground should not couple power
supply noise.
7. Accelerometer and microcontroller should not be a high
current path.
8. A/D sampling rate and any external power supply
switching frequency should be selected such that they do
not interfere with the internal accelerometer sampling
frequency (16 kHz for Low IDD and 52 kHz for Standard
IDD for the sampling frequency). This will prevent aliasing
errors.
VSS
XOUT 15
ST
Logic
Input
1 kΩ
0.1 µF
Figure 4. Accelerometer with Recommended Connection
Diagram
MMA6200 SERIES
Sensor Device Data
Freescale Semiconductor
5
DYNAMIC ACCELERATION
Top View
+Y
16 15 14 13
+X
1
12
2
11
3
10
4
9
5
6
7
-X
8
-Y
16-Pin QFN Package
STATIC ACCELERATION
Top View
Direction of Earth's gravity field.*
XOUT @ 0g = 1.65V
YOUT @ -1g = 0.85V
XOUT @ -1g = 0.85V
YOUT @ 0g = 1.65V
XOUT @ +1g = 2.45V
YOUT @ 0g = 1.65V
XOUT @ 0g = 1.65V
YOUT @ +1g = 2.45V
* When positioned as shown, the Earth's gravity will result in a positive 1g output
MMA6200 SERIES
6
Sensor Device Data
Freescale Semiconductor
6
PIN 1
INDEX AREA
M
A
0.1 C
2X
0.15 C
G
0.08 C
1.98+0.1
5
6
(0.203)
(0.102)
C
SEATING PLANE
DETAIL G
2X
M
0.15 C
B
(0.5)
(1)
VIEW ROTATED 90˚ CLOCKWISE
4
0.1 C A B
16X
4.24
4.04
EXPOSED DIE
ATTACH PAD
13
(45˚)
0.1
DETAIL M
PIN 1 INDEX
16
DETAIL M
12
4.24
4.04
1
0.5
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETERS.
2. INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.5M, 1994.
3. THIS DIMENSION APPLIES TO METALLIZED
TERMINAL AND IS MEASURED BETWEEN 0.25MM
AND 0.30MM FROM TERMINAL TIP.
4. THIS DIMENSION REPRESENTS TERMINAL FULL
BACK FROM PACKAGE EDGE UP TO 0.1MM IS
ACCEPTABLE.
5. COPLANARITY APPLIES TO THE EXPOSED HEAT
SLUG AS WELL AS THE TERMINAL.
6. RADIUS ON TERMINAL IS OPTIONAL.
0.1 C A B
9
4
12X
8
16X
1
5
0.63
0.43
16X
VIEW M-M
0.60
0.40
0.1
M
C A B
0.05
M
C
3
CASE 1477-01
ISSUE O
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
6.0
0.55
4.25
9
8
13
12
1.00
5
16
0.50
6.0
Surface mount board layout is a critical portion of the
total design. The footprint for the surface mount packages must be the correct size to ensure proper solder connection interface between the board and the package.
With the correct footprint, the packages will self-align
when subjected to a solder reflow process. It is always
recommended to design boards with a solder mask layer
to avoid bridging and shorting between solder pads.
1
Pin 1 ID (non metallic)
4
Solder areas
MMA6200 SERIES
Sensor Device Data
Freescale Semiconductor
7
How to Reach Us:
Home Page:
www.freescale.com
E-mail:
[email protected]
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
+1-800-521-6274 or +1-480-768-2130
[email protected]
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
[email protected]
Japan:
Freescale Semiconductor Japan Ltd.
Technical Information Center
3-20-1, Minami-Azabu, Minato-ku
Tokyo 106-0047, Japan
0120 191014 or +81 3 3440 3569
[email protected]
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
+800 2666 8080
[email protected]
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447 or 303-675-2140
Fax: 303-675-2150
[email protected]
MMA6260Q
Rev. 2
10/2004
Information in this document is provided solely to enable system and software implementers to use Freescale
Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or
fabricate any integrated circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to any products herein.
Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its
products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the
application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters that may be provided in Freescale
Semiconductor data sheets and/or specifications can and do vary in different applications and actual
performance may vary over time. All operating parameters, including “Typicals”, must be validated for each
customer application by customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Freescale
Semiconductor product could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or unauthorized application,
Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or
unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the
design or manufacture of the part.
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
All other product or service names are the property of their respective owners.
© Freescale Semiconductor, Inc. 2004. All rights reserved.
Similar pages