ISSI IS61C64B-12J 8k x 8 high-speed cmos static ram Datasheet

ISSI
®
IS61C64B
8K x 8 HIGH-SPEED CMOS STATIC RAM
FEATURES
• High-speed access time: 10, 12, and 15 ns
• Automatic power-down when chip is
deselected
• CMOS low power operation
— 450 mW (typical) operating
— 250 µW (typical) standby
• TTL compatible interface levels
• Single 5V power supply
• Fully static operation: no clock or refresh
required
• Three state outputs
• One Chip Enables (CE) for increased speed
July 2002
DESCRIPTION
The ISSI IS61C64B is a very high-speed, low power,
8192-word by 8-bit static RAM. It is fabricated using ISSI's highperformance CMOS technology. This highly reliable process
coupled with innovative circuit design techniques, yields access times as fast as 10 ns with low power consumption.
When CE is HIGH (deselected), the device assumes a standby
mode at which the power dissipation can be reduced down to
250 µW (typical) with CMOS input levels.
Easy memory expansion is provided by using one Chip Enable
input, CE. The active LOW Write Enable (WE) controls both
writing and reading of the memory.
The IS61C64B is packaged in the JEDEC standard 28-pin,
300-mil SOJ, and TSOP.
FUNCTIONAL BLOCK DIAGRAM
A0-A12
DECODER
256 X 256
MEMORY ARRAY
I/O
DATA
CIRCUIT
COLUMN I/O
VCC
GND
I/O0-I/O7
CE
OE
CONTROL
CIRCUIT
WE
Copyright © 2002 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI
assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device
specification before relying on any published information and before placing orders for products.
Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774
Rev. D
07/01/02
ISSI
IS61C64B
®
TRUTH TABLE
Mode
Not Selected
(Power-down)
Output Disabled
Read
Write
WE
CE
OE
I/O Operation
Vcc Current
X
X
H
H
L
H
X
L
L
L
X
X
H
L
X
High-Z
High-Z
High-Z
DOUT
DIN
ISB1, ISB2
ISB1, ISB2
ICC
ICC
ICC
PIN CONFIGURATION
PIN CONFIGURATION
28-Pin SOJ
28-Pin TSOP (Type 1)
*
A12
1
28
VCC
2
27
WE
A7
3
26
A6
4
25
*A8
A5
5
24
A9
A4
6
23
A11
A3
7
22
OE
A2
8
21
A10
A1
9
20
CE
A0
10
19
I/O7
I/O0
11
18
I/O6
I/O1
12
17
I/O5
I/O2
13
16
I/O4
GND
14
15
I/O3
OE
A11
A9
A8
*
WE
VCC
*
A12
A7
A6
A5
A4
A3
22
23
24
25
26
27
28
1
2
3
4
5
6
7
21
20
19
18
17
16
15
14
13
12
11
10
9
8
A10
CE
I/O7
I/O6
I/O5
I/O4
I/O3
GND
I/O2
I/O1
I/O0
A0
A1
A2
PIN DESCRIPTIONS
A0-A12
Address Inputs
CE
Chip Enable 1 Input
OE
Output Enable Input
WE
Write Enable Input
I/O0-I/O7
Input/Output
*
Must be tied to either
Vcc or GND
Vcc
Power
GND
Ground
Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774
Rev. D
07/01/02
ISSI
IS61C64B
®
ABSOLUTE MAXIMUM RATINGS(1)
Symbol
VTERM
TBIAS
TSTG
PT
IOUT
Parameter
Terminal Voltage with Respect to GND
Temperature Under Bias
Storage Temperature
Power Dissipation
DC Output Current (LOW)
Value
–0.5 to +7.0
–10 to +85
–65 to +150
1.0
20
Unit
V
°C
°C
W
mA
1
2
Notes:
1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation of the
device at these or any other conditions above those indicated in the operational sections
of this specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect reliability.
3
4
OPERATING RANGE
Range
Commercial
Ambient Temperature
0°C to +70°C
Speed
10 ns
12 ns
15 ns
VCC
5V ± 5%
5V ± 10%
5V ± 10%
5
6
DC ELECTRICAL CHARACTERISTICS (Over Operating Range)
Symbol
Parameter
Test Conditions
Min.
Max.
Unit
VOH
Output HIGH Voltage
VCC = Min., IOH = –4.0 mA
2.4
—
V
VOL
Output LOW Voltage
VCC = Min., IOL = 8.0 mA
—
0.4
V
VIH
Input HIGH Voltage
2.2
VCC + 0.5
V
VIL
Input LOW Voltage(1)
–0.5
0.8
V
ILI
Input Leakage
GND - VIN - VCC
–2
2
µA
ILO
Output Leakage
GND - VOUT - VCC, Outputs Disabled
–2
2
µA
7
8
9
Notes:
1. VIL = –3.0V for pulse width less than 10 ns.
10
11
12
Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774
Rev. D
07/01/02
ISSI
IS61C64B
®
POWER SUPPLY CHARACTERISTICS(1) (Over Operating Range)
-10ns
Min. Max.
-12 ns
Min. Max.
-15ns
Min. Max.
Symbol
Parameter
Test Conditions
Unit
ICC
Vcc Dynamic Operating
Supply Current
VCC = Max.,
IOUT = 0 mA, f = fMAX
—
185
—
175
—
135
mA
ISB1
TTL Standby Current
(TTL Inputs)
VCC = Max.,
VIN = VIH or VIL
CE1 • VIH or
CE2 - VIL, f = 0
—
30
—
30
—
30
mA
ISB2
CMOS Standby
Current (CMOS Inputs)
VCC = Max.,
CE1 • VCC – 0.2V,
CE2 - 0.2V,
VIN • VCC – 0.2V, or
VIN - 0.2V, f = 0
—
10
—
10
—
10
mA
Notes:
1. At f = fMAX, address and data inputs are cycling at the maximum frequency, f = 0 means no input lines change.
CAPACITANCE(1,2)
Symbol
Parameter
CIN
Input Capacitance
COUT
Output Capacitance
Conditions
Max.
Unit
VIN = 0V
8
pF
VOUT = 0V
10
pF
Notes:
1. Tested initially and after any design or process changes that may affect these parameters.
2. Test conditions: TA = 25°C, f = 1 MHz, Vcc = 5.0V.
Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774
Rev. D
07/01/02
ISSI
IS61C64B
®
READ CYCLE SWITCHING CHARACTERISTICS(1) (Over Operating Range)
Symbol
–10ns
Min. Max.
Parameter
-12ns
Min. Max.
-15ns
Min. Max.
tRC
Read Cycle Time
10
—
12
—
15
—
ns
tAA
Address Access Time
—
10
—
12
—
15
ns
tOHA
Output Hold Time
2
—
2
—
2
—
ns
tACE
CE Access Time
—
10
—
12
—
15
ns
OE Access Time
—
5
—
6
—
7
ns
OE to Low-Z Output
0
—
0
—
0
—
ns
tHZOE(2) OE to High-Z Output
—
5
—
6
—
6
ns
CE to Low-Z Output
2
—
3
—
3
—
ns
CE to High-Z Output
—
5
—
7
—
8
ns
tDOE
tLZOE
(2)
tLZCE1
tHZCE
(2)
(2)
1
Unit
2
3
4
Notes:
1. Test conditions assume signal transition times of 5 ns or less, timing reference levels of 1.5V, input pulse levels of 0 to 3.0V and
output loading specified in Figure 1a.
2. Tested with the load in Figure 1b. Transition is measured ±500 mV from steady-state voltage. Not 100% tested.
6
AC TEST CONDITIONS
Parameter
Input Pulse Level
Input Rise and Fall Times
Input and Output Timing
and Reference Level
Output Load
5
Unit
0V to 3.0V
3 ns
1.5V
7
See Figures 1a and 1b
8
AC TEST LOADS
9
5V
OUTPUT
OUTPUT
30 pF
Including
jig and
scope
10
480 Ω
480 Ω
5V
255 Ω
5 pF
Including
jig and
scope
255 Ω
11
12
Figure 1a.
Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774
Rev. D
07/01/02
Figure 1b.
ISSI
IS61C64B
®
AC WAVEFORMS
READ CYCLE NO. 1(1,2)
tRC
ADDRESS
tAA
tOHA
tOHA
DOUT
DATA VALID
PREVIOUS DATA VALID
READ CYCLE NO. 2(1,3)
tRC
ADDRESS
tAA
tOHA
OE
tDOE
tHZOE
tLZOE
CE
tACE
tLZCE
DOUT
tHZCE
HIGH-Z
DATA VALID
Notes:
1. WE is HIGH for a Read Cycle.
2. The device is continuously selected. OE, CE = VIL.
3. Address is valid prior to or coincident with CE LOW transitions.
Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774
Rev. D
07/01/02
ISSI
IS61C64B
®
WRITE CYCLE SWITCHING CHARACTERISTICS(1,3) (Over Operating Range)
Symbol
Parameter
–10ns
Min. Max.
-12ns
Min. Max.
-15ns
Min. Max.
Unit
tWC
Write Cycle Time
10
—
12
—
15
—
ns
tSCE
CE to Write End
9
—
10
—
12
—
ns
tAW
Address Setup Time to Write End
9
—
10
—
12
—
ns
tHA
Address Hold from Write End
0
—
0
—
0
—
ns
tSA
Address Setup Time
0
—
0
—
0
—
ns
tPWE(4)
WE Pulse Width
8
—
8
—
10
—
ns
tSD
Data Setup to Write End
8
—
8
—
9
—
ns
Data Hold from Write End
0
—
0
—
0
—
ns
WE LOW to High-Z Output
—
6
—
6
—
7
ns
tLZWE(2) WE HIGH to Low-Z Output
0
—
0
—
0
—
ns
tHD
tHZWE
(2)
Notes:
1. Test conditions assume signal transition times of 5 ns or less, timing reference levels of 1.5V, input pulse levels of 0 to 3.0V and
output loading specified in Figure 1a.
2. Tested with the load in Figure 1b. Transition is measured ±500 mV from steady-state voltage. Not 100% tested.
3. The internal write time is defined by the overlap of CE LOW and WE LOW. All signals must be in valid states to initiate a Write,
but any one can go inactive to terminate the Write. The Data Input Setup and Hold timing are referenced to the rising or falling
edge of the signal that terminates the write.
1
2
3
4
5
6
7
8
9
10
11
12
Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774
Rev. D
07/01/02
ISSI
IS61C64B
®
AC WAVEFORMS
WE Controlled)(1,2)
WRITE CYCLE NO. 1 (WE
tWC
ADDRESS
tHA
tSCE
CE
tAW
tPWE
WE
tSA
DOUT
tHZWE
tLZWE
HIGH-Z
DATA UNDEFINED
tSD
DIN
tHD
DATA-IN VALID
CE1
WRITE CYCLE NO. 2 (CE1
CE1, CE2 Controlled)(1,2)
tWC
ADDRESS
tSA
tHA
tSCE
CE
tAW
tPWE
WE
tHZWE
DOUT
DATA UNDEFINED
tLZWE
HIGH-Z
tSD
DIN
tHD
DATA-IN VALID
Notes:
1. The internal write time is defined by the overlap of CE LOW and WE LOW. All signals must be in valid states to initiate a Write,
but any one can go inactive to terminate the Write. The Data Input Setup and Hold timing are referenced to the rising or falling
edge of the signal that terminates the write.
2. I/O will assume the High-Z state if OE = VIH.
Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774
Rev. D
07/01/02
ISSI
IS61C64B
ORDERING INFORMATION
Commercial Range: 0°C to +70°C
Speed (ns)
Order Part No.
Package
10
IS61C64B-10J
IS61C64B-10T
300-mil Plastic SOJ
Plastic TSOP
12
IS61C64B-12J
IS61C64B-12T
300-mil Plastic SOJ
Plastic TSOP
15
IS61C64B-15J
IS61C64B-15T
300-mil Plastic SOJ
Plastic TSOP
®
1
2
3
4
5
6
7
8
9
10
11
12
Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774
Rev. D
07/01/02
Similar pages