C o ntrol In t eg ra t ed P Owe r Sys te m (C IPOS™) I GCM 06G6 0GA Datasheet For Power Management Application 1 Ver. 1.1, 2014-06-01 CIPOS™ IGCM06G60GA Table of Contents CIPOS™ Control Integrated POwer System ........................................................................................................ 3 Features .............................................................................................................................................................. 3 Target Applications ........................................................................................................................................... 3 Description ......................................................................................................................................................... 3 System Configuration ....................................................................................................................................... 3 Pin Configuration .................................................................................................................................................... 4 Internal Electrical Schematic ................................................................................................................................. 4 Pin Assignment ....................................................................................................................................................... 5 Pin Description .................................................................................................................................................. 5 HIN(U,V,W) and LIN(U,V,W) (Low side and high side control pins, Pin 7 - 12) ................................................ 5 VFO (Fault-output and NTC, Pin 14) ................................................................................................................. 6 ITRIP (Over current detection function, Pin 15) ................................................................................................ 6 VDD, VSS (Low side control supply and reference, Pin 13, 16) ....................................................................... 6 VB(U,V,W) and VS(U,V,W) (High side supplies, Pin 1 - 6) ............................................................................... 6 N (Low side common emitter, Pin 17 - 19) ........................................................................................................ 6 W, V, U (High side emitter and low side collector, Pin 20 - 22)......................................................................... 6 P (Positive bus input voltage, Pin 23)................................................................................................................ 6 Absolute Maximum Ratings................................................................................................................................... 7 Module Section .................................................................................................................................................. 7 Inverter Section.................................................................................................................................................. 7 Control Section .................................................................................................................................................. 7 Recommended Operation Conditions .................................................................................................................. 8 Static Parameters ................................................................................................................................................... 9 Dynamic Parameters ............................................................................................................................................ 10 Bootstrap Parameters .......................................................................................................................................... 10 Thermistor ............................................................................................................................................................. 11 Mechanical Characteristics and Ratings............................................................................................................ 11 Circuit of a Typical Application ........................................................................................................................... 12 Switching Times Definition .................................................................................................................................. 12 Electrical characteristic ....................................................................................................................................... 13 Package Outline .................................................................................................................................................... 14 Datasheet 2 Ver. 1.1, 2014-06-01 CIPO™ IGCM06G60GA CIPOS™ Control Integrated POwer System Dual In-Line Intelligent Power Module 3Φ-bridge 600V / 6A Features Description Fully isolated Dual In-Line molded module • Infineon reverse conducting IGBTs with monolithic body diode • Rugged SOI gate driver technology with stability against transient and negative voltage • Allowable negative VS potential up to -11V for signal transmission at VBS=15V • Integrated bootstrap functionality • Over current shutdown • Temperature monitor • Under-voltage lockout at all channels • Low side common emitter • Cross-conduction prevention • All of 6 switches turn off during protection • Lead-free terminal plating; RoHS compliant The CIPOS™ module family offers the chance for integrating various power and control components to increase reliability, optimize PCB size and system costs. It is designed to control three phase AC motors and permanent magnet motors in variable speed drives for applications like a refrigerator and a dish washer. The package concept is specially adapted to power applications, which need good thermal conduction and electrical isolation, but also EMIsave control and overload protection. The features of Infineon reverse conducting IGBT are combined with an optimized SOI gate driver for excellent electrical performance. System Configuration • 3 half bridges with reverse conducting IGBT • 3Φ SOI gate driver Target Applications • Thermistor • Dish washers • Pin-to-heasink creepage distance typ. 1.6mm • Refrigerators • Fans • Low power motor drives Datasheet 3 Ver. 1.1, 2014-06-01 CIPOS™ IGCM06G60GA Pin Configuration Bottom View Figure 1: Pin configuration Internal Electrical Schematic Figure 2: Internal schematic Datasheet 4 Ver. 1.1, 2014-06-01 CIPOS™ IGCM06G60GA Pin Assignment Pin Number Pin Name Pin Description 1 VS(U) U-phase high side floating IC supply offset voltage 2 VB(U) U-phase high side floating IC supply voltage 3 VS(V) V-phase high side floating IC supply offset voltage 4 VB(V) V-phase high side floating IC supply voltage 5 VS(W) W-phase high side floating IC supply offset voltage 6 VB(W) W-phase high side floating IC supply voltage 7 HIN(U) U-phase high side gate driver input 8 HIN(V) V-phase high side gate driver input 9 HIN(W) W-phase high side gate driver input 10 LIN(U) U-phase low side gate driver input 11 LIN(V) V-phase low side gate driver input 12 LIN(W) W-phase low side gate driver input 13 VDD Low side control supply 14 VFO Fault output / Temperature monitor 15 ITRIP Over current shutdown input 16 VSS Low side control negative supply 17, 18, 19 N Low side common emitter 20 W Motor W-phase output 21 V Motor V-phase output 22 U Motor U-phase output 23 P Positive bus input voltage 24 NC No Connection Pin Description Schmitt-Trigger HIN(U,V,W) and LIN(U,V,W) (Low side and high side control pins, Pin 7 - 12) These pins are positive logic and they are responsible for the control of the integrated IGBT. The Schmitt-trigger input thresholds of them are such to guarantee LSTTL and CMOS compatibility down to 3.3V controller outputs. Pull-down resistor of about 5kΩ is internally provided to pre-bias inputs during supply start-up and a zener clamp is provided for pin protection purposes. Input Schmitttrigger and noise filter provide beneficial noise rejection to short input pulses. HINx LINx SΩITCH LEVEL VIH; VIL Figure 3: Input pin structure a) tFILIN HO LO b) tFILIN HIN LIN HIN LIN The noise filter suppresses control pulses which are below the filter time tFILIN. The filter acts according to Figure 4. Datasheet INPUT NOISE FILTER UZ=10.5V ≈ 5kΩ high low HO LO Figure 4: Input filter timing diagram 5 Ver. 1.1, 2014-06-01 CIPOS™ IGCM06G60GA It is recommended for proper work of CIPOS™ not to provide input pulse-width lower than 1us. The IC shuts down all the gate drivers’ outputs, when the VDD supply voltage is VDDUV- = 10.4V. This prevents the external switches from critically low gate voltage during on-state and therefore from excessive dissipation. The integrated gate drive provides additionally a shoot through prevention capability which avoids the simultaneous on-state of two gate drivers of the same leg (i.e. HO1 and LO1, HO2 and LO2, HO3 and LO3). When two inputs of a same leg are activated, only former activated one is activated so that the leg is kept steadily in a safe state. VB(U,V,W) and VS(U,V,W) (High side supplies, Pin 1 - 6) VB to VS is the high side supply voltage. The high side circuit can float with respect to VSS following the external high side power device emitter voltage. A minimum deadtime insertion of typically 380ns is also provided by driver IC, in order to reduce crossconduction of the external power switches. Due to the low power consumption, the floating driver stage is supplied by integrated bootstrap circuit. VFO (Fault-output and NTC, Pin 14) The VFO pin indicates a module failure in case of under voltage at pin VDD or in case of triggered over current detection at ITRIP. A pull-up resistor is externally required to bias the NTC. The under-voltage detection operates with a rising supply threshold of typical VBSUV+ = 12.1V and a falling threshold of VBSUV- = 10.4V. VS(U,V,W) provide a high robustness against negative voltage in respect of VSS of -50V transiently. This ensures very stable designs even under rough conditions. VDD RON ,FLT VFO >1 VSS from ITRIP -Latch N (Low side common emitter, Pin 17 - 19) The low side common emitter is available for current measurement. It is recommended to keep the connection to pin VSS as short as possible in order to avoid unnecessary inductive voltage drops.. from uv - detection Thermistor power below power levels power CIPOS™ Figure 5: Internal circuit at pin VFO W, V, U (High side emitter and low side collector, Pin 20 - 22) These pins are motor U, V, W input pins The same pin provides direct access to the NTC, which is referenced to VSS. An external pull-up resistor connected to +5V ensures, that the resulting voltage can be directly connected to the microcontroller P (Positive bus input voltage, Pin 23) The high side IGBT are connected to the bus voltage. It is noted that the bus voltage does not exceed 450 V. ITRIP (Over current detection function, Pin 15) CIPOS™ provides an over current detection function by connecting the ITRIP input with the motor current feedback. The ITRIP comparator threshold (typ. 0.47V) is referenced to VSS ground. An input noise filter (typ: tITRIPMIN = 530ns) prevents the driver to detect false over-current events. Over current detection generates a shut down of all outputs of the gate driver after the shutdown propagation delay of typically 1000ns. The fault-clear time is set to typical 65us. VDD, VSS (Low side control supply and reference, Pin 13, 16) VDD is the low side supply and it provides power both to input logic and to low side output power stage. Input logic is referenced to VSS ground. The under-voltage circuit enables the device to operate at power on when a supply voltage of at least a typical voltage of VDDUV+ = 12.1V is present. Datasheet 6 Ver. 1.1, 2014-06-01 CIPOS™ IGCM06G60GA Absolute Maximum Ratings (VDD = 15V and TJ = 25°C, if not stated otherwise) Module Section Description Condition Storage temperature range Insulation test voltage RMS, f = 60Hz, t =1min Operating case temperature range Refer to Figure 6 Symbol Value Unit min max Tstg -40 125 °C VISOL 2000 - V TC -40 100 °C Inverter Section Description Condition Symbol Value min max Unit Max. blocking voltage IC = 250µA VCES 600 - V DC link supply voltage of P-N Applied between P-N VPN - 450 V DC link supply voltage (surge) of P-N Applied between P-N VPN(surge) - 500 V Output current TC = 25°C, TJ < 150°C TC = 100°C, TJ < 150°C IC -6 -4 6 4 A less than 1ms IC -12 12 A VDC ≤ 400V, TJ = 150°C tSC - 5 µs Power dissipation per IGBT Ptot - 23.6 W Operating junction temperature range TJ -40 150 °C RthJC - 5.3 K/W Maximum peak output current Short circuit withstand time 1 Single IGBT thermal resistance, junction-case Control Section Description Condition Value min max Unit Module supply voltage VDD -1 20 V High side floating supply voltage (VB vs. VS) VBS -1 20 V VIN VITRIP -1 -1 10 10 V fPWM - 20 kHz Input voltage LIN, HIN, ITRIP Switching frequency 1 Symbol Allowed number of short circuits: <1000; time between short circuits: >1s. Datasheet 7 Ver. 1.1, 2014-06-01 CIPOS™ IGCM06G60GA Recommended Operation Conditions All voltages are absolute voltages referenced to VSS -potential unless otherwise specified. Description Symbol Value min typ max Unit DC link supply voltage of P-N VPN 0 - 400 V High side floating supply voltage (VB vs. VS) VBS 13.5 - 18.5 V Low side supply voltage VDD 14.0 16 18.5 V Control supply variation ΔVBS, ΔVDD -1 -1 - 1 1 V/µs Logic input voltages LIN,HIN,ITRIP VIN VITRIP 0 0 - 5 5 V Between VSS - N (including surge) VSS -5 - 5 V Figure 6: TC measurement point 1 1 Any measurement except for the specified point in figure 6 is not relevant for the temperature verification and brings wrong or different information. Datasheet 8 Ver. 1.1, 2014-06-01 CIPOS™ IGCM06G60GA Static Parameters (VDD = 15V and TJ = 25°C, if not stated otherwise) Description Condition Symbol Value Unit min typ max VCE(sat) - 1.6 1.8 2.0 - V TJ = 25°C 150°C VF - 1.75 1.8 2.2 - V VCE = 600V ICES - - 1 mA Logic "1" input voltage (LIN,HIN) VIH - 2.1 2.5 V Logic "0" input voltage (LIN,HIN) VIL 0.7 0.9 - V ITRIP positive going threshold VIT,TH+ 400 470 540 mV ITRIP input hysteresis VIT,HYS 40 70 - mV VDD and VBS supply under voltage positive going threshold VDDUV+ VBSUV+ 10.8 12.1 13.0 V VDD and VBS supply under voltage negative going threshold VDDUVVBSUV- 9.5 10.4 11.2 V VDD and VBS supply under voltage lockout hysteresis VDDUVH VBSUVH 1.0 1.7 - V VINCLAMP 9.0 10.1 12.5 V Collector-Emitter saturation voltage Iout = 4A TJ = 25°C 150°C Emitter-Collector forward voltage Collector-Emitter leakage current Iout = -4A Input clamp voltage (HIN, LIN, ITRIP) Iin = 4mA Quiescent VBx supply current (VBx only) HIN = 0V IQBS - 300 500 µA Quiescent VDD supply current (VDD only) LIN = 0V, HINX = 5V IQDD - 370 900 µA Input bias current VIN = 5V IIN+ - 1 1.5 mA Input bias current VIN = 0V IIN- - 2 - µA ITRIP input bias current VITRIP = 5V IITRIP+ - 65 150 µA VFO input bias current VFO = 5V, VITRIP = 0V IFO - 60 - µA VFO output voltage IFO = 10mA, VITRIP = 1V VFO - 0.5 - V Datasheet 9 Ver. 1.1, 2014-06-01 CIPOS™ IGCM06G60GA Dynamic Parameters (VDD = 15V and TJ = 25°C, if not stated otherwise) Description Condition typ max ton - 650 - ns tr - 20 - ns tc(on) - 100 - ns trr - 130 - ns toff - 680 - ns tf - 180 - ns tc(off) - 220 - ns tSCP - 1420 - ns tITRIPmin - 530 - ns tFILIN - 290 - ns tFLTCLR 40 65 200 µs DTPWM 1.0 - - µs DTIC - 380 - ns VLIN,HIN = 5V; Iout =4A, VDC = 300V Turn-on switching time Reverse recovery time Turn-off propagation delay time Turn-off fall time Turn-off switching time VLIN,HIN = 0V; Iout =4A, VDC = 300V Short circuit propagation delay time From VIT,TH+ to 10% ISC Input filter time ITRIP VITRIP = 1V Input filter time at LIN, HIN for turn on and off VLIN,HIN = 0V & 5V Fault clear time after ITRIP-fault VITRIP = 1V Deadtime between low side and high side Unit min Turn-on propagation delay time Turn-on rise time Value Symbol Deadtime of gate drive circuit IGBT turn-on energy (includes reverse recovery of diode) VDC = 300V, IC = 4A, TJ = 25°C 150°C Eon - 75 130 - µJ IGBT turn-off energy VDC = 300V, IC = 4A, TJ = 25°C 150°C Eoff - 120 190 - µJ Diode recovery energy VDC = 300V, IC = 4A, TJ = 25°C 150°C Erec - 40 70 - µJ Bootstrap Parameters (TJ = 25°C, if not stated otherwise) Description Condition Symbol Repetitive peak reverse voltage 1 VRRM Value Unit min typ max 600 - - V - Ω Bootstrap resistance of U-phase 1 VS2 or VS3 = 300V, TJ = 25°C VS2 and VS3 = 0V, TJ = 25°C VS2 or VS3 = 300V, TJ = 125°C VS2 and VS3 = 0V, TJ = 125°C RBS1 - 35 40 50 65 Reverse recovery time IF = 0.6A, di/dt = 80A/µs trr_BS - 50 - ns Forward voltage drop IF = 20mA, VS2 and VS3 = 0V VF_BS - 2.6 - V RBS2 and RBS3 have same values to RBS1. Datasheet 10 Ver. 1.1, 2014-06-01 CIPOS™ IGCM06G60GA Thermistor Description Resistor Condition TNTC = 25°C B-constant of NTC (Negative temperature coefficient) Symbol Value Unit min typ max RNTC - 85 - kΩ B(25/100) - 4092 - K Figure 7: Thermistor resistance – temperature curve and table (For more information, please refer to the application note ‘AN CIPOS-mini 1 Technical description’) Mechanical Characteristics and Ratings Description Condition Value Unit min typ max Mounting torque M3 screw and washer 0.59 0.69 0.78 Nm Flatness Refer to Figure 8 -50 - 100 µm - 6.15 - g Weight Figure 8: Flatness measurement position Datasheet 11 Ver. 1.1, 2014-06-01 CIPOS™ IGCM06G60GA Circuit of a Typical Application NC (24) P (23) (1) VS(U) (2) VB(U) VB1 HO1 RBS1 (3) VS(V) (4) VB(V) UU(22) VS1 HO2 VB2 RBS2 V (21) VS2 3-ph AC Motor (5) VS(W) (6) VB(W) HO3 VB3 W (20) VS3 RBS3 (7) HIN(U) (8) HIN(V) (9) HIN(W) Micro Controller (10) LIN(U) (11) LIN(V) (12) LIN(W) VDD line (13) VDD 5 or 3.3V line LO1 HIN1 HIN2 N (19) HIN3 LIN1 LO2 LIN2 LIN3 N (18) VDD (14) VFO VFO (15) ITRIP ITRIP (16) VSS VSS LO3 N (17) Thermistor Figure 9: Application circuit Switching Times Definition HINx LINx 2.1V 0.9V trr toff ton 10% iCx 90% 90% tf vCEx 10% tr 10% 10% 10% tc(on) tc(off) Figure 10: Switching times definition Datasheet 12 Ver. 1.1, 2014-06-01 CIPOS™ IGCM06G60GA Electrical characteristic 9 8 7 6 VDD=13V VDD=15V VDD=20V 4 3 2 1 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 VCE(sat), Collector - Emitter voltage [V] 4.0 Eoff, Turn off switching energy loss [mJ] High side @TJ=25℃dd High side @TJ=150℃d Low side @TJ=25℃dd Low side @TJ=150℃d 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0 1 2 3 4 5 6 7 8 Ic, Collector current [A] 9 10 11 7 6 5 4 TJ=25℃ TJ=150℃ 3 2 1 12 700 650 3.5 4.0 0.15 0.10 0.05 0.00 VDC=300V VDD=15V 0 1 2 3 4 5 6 7 8 Ic, Collector current [A] 9 10 11 1 2 3 4 5 6 7 8 Ic, Collector current [A] 9 10 11 trr, Reverse recovery time [ns] High side @TJ=25℃ High side @TJ=150℃ Low side @TJ=25℃ Low side @TJ=150℃ 600 500 400 300 200 300 250 200 150 100 0 1 2 3 4 5 6 7 8 Ic, Collector current [A] 9 10 11 100 1 2 3 4 5 6 7 8 Ic, Collector current [A] 9 Typ. Turn off switching time Datasheet 10 TJ=25℃ TJ=150℃ 3 2 1 450 VDC=300V VDD=15V 400 High side @TJ=25℃dd 350 11 12 Low side @TJ=25℃ddd Low side @TJ=150℃d 250 160 1.5 2.0 2.5 3.0 3.5 High side @TJ=25℃dd High side @TJ=150℃d Low side @TJ=25℃dd Low side @TJ=150℃d 140 120 100 80 60 40 20 0 1 2 3 4 5 6 7 8 Ic, Collector current [A] 9 10 11 12 VDC=300V VDD=15V 1600 High side @TJ=25℃ High side @TJ=150℃ Low side @TJ=25℃ Low side @TJ=150℃ 1400 1200 1000 800 600 0 1 2 3 4 5 6 7 8 Ic, Collector current [A] 9 10 11 12 10 1 0.1 0.01 200 150 D : duty ratio D=50% D=20% D=10% D=5% D=2% Single pulse 1E-3 100 0 1.0 Typ. Turn off propagation delay time High side @TJ=150℃d 300 0.5 VDC=300V VDD=15V 180 0 12 50 0 4 Typ. Turn on switching time 900 700 5 1800 High side @TJ=25℃dd High side @TJ=150℃d Low side @TJ=25℃dd Low side @TJ=150℃d 500 800 6 Typ. Reverse recovery energy loss VDC=300V VDD=15V 350 0 12 VDC=300V VDD=15V 1000 7 VF, Emitter - Collector voltage [V] Typ. Emitter – Collector forward voltage 12 50 0 8 0 0.0 4.5 0.20 1100 tc(off), Turn off switching time [ns] 3.0 0.25 Typ. Turn on propagation delay time 0 2.5 9 200 0.30 tc(on), Turn on switching time [ns] ton, Turn on propagation delay time [ns] 750 600 2.0 High side @TJ=25℃dd High side @TJ=150℃d Low side @TJ=25℃dd Low side @TJ=150℃d 0.35 400 High side @TJ=25℃dd High side @TJ=150℃d Low side @TJ=25℃dd Low side @TJ=150℃d 800 1.5 10 Typ. Turn off switching energy loss VDC=300V VDD=15V 850 1.0 0.40 Typ. Turn on switching energy loss 900 0.5 VCE(sat), Collector - Emitter voltage [V] ZthJC, RC-IGBT transient thermal resistance [K/W] Eon, Turn on switching energy loss [mJ] 0.8 0.7 8 Typ. Collector – Emitter saturation voltage VDC=300V VDD=15V 0.9 9 0 0.0 Typ. Collector – Emitter saturation voltage 1.0 10 Erec, Reverse recovery energy loss [uJ] 5 11 IF, Emitter - Collector current [A] 10 12 VDD=15V 11 Ic, Collector - Emitter current [A] Ic, Collector - Emitter current [A] 12 TJ=25℃ 11 toff, Turn off propagation delay time [ns] 12 0 1 2 3 4 5 6 7 8 Ic, Collector current [A] 9 Typ. Reverse recovery time 13 10 11 12 1E-4 1E-7 1E-6 1E-5 1E-4 1E-3 0.01 0.1 tP, Pulse width [sec.] 1 10 100 IGBT transient thermal resistance at all six IGBTs operation Ver. 1.1, 2014-06-01 CIPOS™ IGCM06G60GA Package Outline Datasheet 14 Ver. 1.1, 2014-06-01 CIPOS™ IGCM06G60GA Revision History Previous Version: Datasheet Ver. 1.0 Major changes since the last revision Page or Reference 8 14 Datasheet Description of change Figure 6 updated Package Outline updated 15 Ver. 1.1, 2014-06-01 Trademarks of Infineon Technologies AG AURIX™, C166™, CanPAK™, CIPOS™, CIPURSE™, CoolGaN™, CoolMOS™, CoolSET™, CoolSiC™, CORECONTROL™, CROSSAVE™, DAVE™, DI-POL™, DrBLADE™, EasyPIM™, EconoBRIDGE™, EconoDUAL™, EconoPACK™, EconoPIM™, EiceDRIVER™, eupec™, FCOS™, HITFET™, HybridPACK™, ISOFACE™, IsoPACK™, i-Wafer™, MIPAQ™, ModSTACK™, my-d™, NovalithIC™, OmniTune™, OPTIGA™, OptiMOS™, ORIGA™, POWERCODE™, PRIMARION™, PrimePACK™, PrimeSTACK™, PROFET™, PRO-SIL™, RASIC™, REAL3™, ReverSave™, SatRIC™, SIEGET™, SIPMOS™, SmartLEWIS™, SOLID FLASH™, SPOC™, TEMPFET™, thinQ!™, TRENCHSTOP™, TriCore™. Other Trademarks Advance Design System™ (ADS) of Agilent Technologies, AMBA™, ARM™, MULTI-ICE™, KEIL™, PRIMECELL™, REALVIEW™, THUMB™, µVision™ of ARM Limited, UK. ANSI™ of American National Standards Institute. AUTOSAR™ of AUTOSAR development partnership. Bluetooth™ of Bluetooth SIG Inc. CAT-iq™ of DECT Forum. COLOSSUS™, FirstGPS™ of Trimble Navigation Ltd. EMV™ of EMVCo, LLC (Visa Holdings Inc.). EPCOS™ of Epcos AG. FLEXGO™ of Microsoft Corporation. HYPERTERMINAL™ of Hilgraeve Incorporated. MCS™ of Intel Corp. IEC™ of Commission Electrotechnique Internationale. IrDA™ of Infrared Data Association Corporation. ISO™ of INTERNATIONAL ORGANIZATION FOR STANDARDIZATION. MATLAB™ of MathWorks, Inc. MAXIM™ of Maxim Integrated Products, Inc. MICROTEC™, NUCLEUS™ of Mentor Graphics Corporation. MIPI™ of MIPI Alliance, Inc. MIPS™ of MIPS Technologies, Inc., USA. muRata™ of MURATA MANUFACTURING CO., MICROWAVE OFFICE™ (MWO) of Applied Wave Research Inc., OmniVision™ of OmniVision Technologies, Inc. Openwave™ of Openwave Systems Inc. RED HAT™ of Red Hat, Inc. RFMD™ of RF Micro Devices, Inc. SIRIUS™ of Sirius Satellite Radio Inc. SOLARIS™ of Sun Microsystems, Inc. SPANSION™ of Spansion LLC Ltd. Symbian™ of Symbian Software Limited. TAIYO YUDEN™ of Taiyo Yuden Co. TEAKLITE™ of CEVA, Inc. TEKTRONIX™ of Tektronix Inc. TOKO™ of TOKO KABUSHIKI KAISHA TA. UNIX™ of X/Open Company Limited. VERILOG™, PALLADIUM™ of Cadence Design Systems, Inc. VLYNQ™ of Texas Instruments Incorporated. VXWORKS™, WIND RIVER™ of WIND RIVER SYSTEMS, INC. ZETEX™ of Diodes Zetex. Last Trademarks Update 2014-07-17 www.Infineon.com Edition 2014-06-01 Published by Infineon Technologies AG 81726 München, Germany © Infineon Technologies AG 2015. All Rights Reserved. IMPORTANT NOTICE The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics (“Beschaffenheitsgarantie”). With respect to any examples, hints or any typical values stated herein and/or any information regarding the application of the product, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. In addition, any information given in this document is subject to customer’s compliance with its obligations stated in this document and any applicable legal requirements, norms and standards concerning customer’s products and any use of the product of Infineon Technologies in customer’s applications. The data contained in this document is exclusively intended for technically trained staff. It is the responsibility of customer’s technical departments to evaluate the suitability of the product for the intended application and the completeness of the product information given in this document with respect to such application. For further information on the product, technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies office (www.infineon.com). WARNINGS Due to technical requirements products may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies office. Except as otherwise explicitly approved by Infineon Technologies in a written document signed by authorized representatives of Infineon Technologies, Infineon Technologies’ products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be expected to result in personal injury.