POWER DS1200DC 1200 Watt Distributed Power System Data Sheet Front-end Bulk Power Total Output Power: 180 to 264 Vac: 1200 W 3.3 Vdc or 5.0 Vdc Standby Output Telco Input Range: -40 to -72 Vdc SPECIAL FEATURES GR-1089-CORE Issue 4 compliant 1U X 2U form factor 21.71 W / in3 +12 Vdc Output +3.3 Vdc standby (5 V standby option) No minimum load required Hot plug operation N + 1 redundant Internal OR’ing fets Active current sharing shares with DS1200 AC unit (10 - 100% load) Built-in cooling fan (40 mm x 28 mm) I2C communication interface bus PMBus compliant EERPOM for FRU data Red/green bi-color LED status Internal fan speed control Fan Fail Tach Output Signal INTEL, SSI Std. logic timing INTEL, SSI Std. FRU data format Full digital control Two year warranty NEBS compliant Electrical Specifications Input Input range -40 Vdc to -72 Vdc Inrush current ETSI EN300 132-2 part 4.7 compliant Efficiency > 85% typical at high line 50% load Conducted EMI Per GR-1089-CORE Issue 4 Radiated EMI Per GR-1089-CORE Issue 4 Leakage current 1.40 mA @ 240 Vac Hold up time 12 ms minimum Output Main DC voltage +12 V @ 100 A Standby +3.3 Vsb @ 6 A (5 V @ 4 A available) Adjustment range ±5% on +12 V only using I2C Regulation +12 Vdc; ±5% +3.3 or 5.0 Vsb ±5% Overcurrent +12 Vdc; latches off if overcurrent lasts over 1 second, otherwise it is auto recovery (See Table 1 next page) +3.3 Vsb, 9 A max (hiccup mode) Overvoltage +12 Vdc; 13.2 - 14.4 Vdc +3.3 Vsb; 3.76 - 4.30 Vdc SAFETY Undervoltage +12 Vdc; 9 - 10.8 V (latch off) UL/cUL 60950 (UL Recognized) NEMKO+ CB Report EN60950 EN60950 CE Mark China CCC Turn-on delay 2 second max, 5 - 50 mS, monotonic rise Main output rise time 5 - 50 mS, monotonic rise DS1200DC Data Sheet Logic Control PS_SEATED (A4) TTL logic LOW if power supply is seated into system connector. This is a short pin. A logic HIGH if the PSU is removed PWR GOOD (C3) Active TTL high when output is within regulation limits. AC OK (B1) A low logic level if the input voltage is within allowable limits. A TTL logic HIGH level, and a 5 mS early warning signal before 12.0 V DC output loss of regulation. PS_INHIBIT/PS_KILL (B4) When left open power supply operation will be inhibited. When the power supply is inserted into the system, this pin will be pull low by the system and turn the power supply on only after all other power supply pins have seated. PS ON (A1) The output will be enabled when this signal is pulled low, below 0.8 V outputs disabled when pin is driven high or left open. Environmental Specifications Operating temperature -10 to 55 °C Storage temperature -40 to +85 °C Altitude, operating 13,000 feet Electromagnetic susceptibility / Input transients GR-1089-CORE Issue 4 RoHS & lead free Compliant Humidity 20 - 90% RH, non condensing Shock and vibration specifications Complies with Artesyn standard specifications plus additional NEBS requirement MTBF (demonstrated 500 K Hrs at full load, 40 °C Ordering Information Nominal Output Voltage Set Point Set Point Tolerance Total Regulation Min Max Output Ripple P/P Overcurrent Standby DS1200DC-3 12.0 V ±0.2% ±0.5% 0A 100 A 120 mV 118 A - 147.6 A* 3.3 V @ 6 A STD DS1200DC-3-001 12.0 V ±0.2% ±0.5% 0A 100 A 120 mV 118 A - 147.6 A* 3.3 V @ 6 A REV** DS1200DC-3-002 12.0 V ±0.2% ±0.5% 0A 100 A 120 mV 118 A - 147.6 A* 5.0 V @ 4 A STD DS1200DC-3-004 12.0 V ±0.2% ±0.5% 0A 100 A 120 mV 118 A - 147.6 A* 5.0 V @ 4 A REV** Model Number* * Over current latches off if overcurrent lasts over 1 seconds, otherwise it is auto recovery. ** Derating may apply. Current Air Flow DS1200DC Data Sheet 39.9 ± 0.5 Mechanical Drawing FORWARD AIRFLOW DIRECTION 81.3 ± 0.8 MODEL LABEL (LABEL TEXT & CHARACTERS AS ORIENTED) 275.5 279.4 ± 1 9 Conditon Stand-by - ON; Main output - OFF; AC PRESENT Stand-by - ON; Main output - ON Main output OCP, UVP, OVP FAN_FAULT; OTP; Stand-by OCP/UVP LED Status Blinking green Solid green Blinking Amber Amber 6 68.8 7.02 ± 0.8 DS1200DC Data Sheet Mechanical Specifications DC Output Connector Pinout Assignment Pin Assignments Male connector as viewed from the rear of the supply: Pin Signal Name D1 D2 D3 D4 D5 D6 PB1 Main output return C1 C2 C3 C4 C5 C6 PB2 Main output return B1 B2 B3 B4 B5 B6 A1 A2 A3 A4 A5 A6 PB3 Main output return PB4 + Main output PB5 + Main output PB6 + Main output PB1 PB2 PB3 PB4 PB5 PB6 Power Supply Side 1. FCI Power Blade 51721 series 51721-10002406AA A1 PS_ON_ A2 Main output remote sense return 2. Molex Power Connector SD-87667 series 87667-7002 A3 Spare A4 PS_SEATED (Power supply seated) Mating Connector (System Side) A5 STANDBY 1. FCI Power Blade 51741-10002406CC Straight Pins A6 STANDBY RETURN B1 AC_OK (AC Input Present) 2. FCI Power Blade 51761-10002406AALF Right Angle B2 Main output remote sense B3 Main ouput current share B4 PS_INHIBIT / PS_Kill B5 STANDBY B6 STANDBY Return C1 ADC (I2C Data Signal) C2 SCL (I2C Clock Signal) C3 POWER GOOD C4 Spare C5 STANDBY C6 STANDBY RETURN D1 A0 (I2C Address BIT 0 Signal) D2 A1 (I2C Address BIT 1 Signal) D3 S_INT (Alarm) D4 STANDYBY RMT SENSE D5 STANDBY D6 STANDBY RETURN WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong +852 2176 3333 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2015 Artesyn Embedded Technologies, Inc. www.artesyn.com For more information: www.artesyn.com/power For support: [email protected] DS1200DC 30Jul2015