Revised August 2004 NC7SZ38 TinyLogic UHS 2-Input NAND Gate (Open Drain Output) General Description Features The NC7SZ38 is a single 2-Input NAND Gate with open drain output stage from Fairchild’s Ultra High Speed Series of TinyLogic. The device is fabricated with advanced CMOS technology to achieve ultra high speed with high output drive while maintaining low static power dissipation over a very broad VCC operating range. The device is specified to operate over the 1.65V to 5.5V VCC range. The inputs and output are high impedance when VCC is 0V. Inputs tolerate voltages up to 6V independent of VCC operating voltage. The open drain output stage will tolerate voltages up to 6V independent of VCC when in the high impedance state. ■ Space saving SOT23 or SC70 5-lead package ■ Ultra small MicroPak leadless package ■ Open Drain output stage for OR tied applications ■ Ultra High Speed; tPD 2.4 ns Typ into 50 pF at 5V VCC ■ High Output Sink Drive; 24 mA at 3V VCC ■ Broad VCC Operating Range; 1.65V to 5.5V ■ Matches the performance of LCX when operated at 3.3V VCC ■ Power down high impedance inputs/output ■ Overvoltage Tolerant inputs facilitate 5V to 3V translation ■ Patented noise/EMI reduction circuitry implemented Ordering Code: Order Package Product Code Number Number Top Mark NC7SZ38M5X MA05B 7Z38 5-Lead SOT23, JEDEC MO-178, 1.6mm NC7SZ38P5X MAA05A Z38 5-Lead SC70, EIAJ SC-88a, 1.25mm Wide 3k Units on Tape and Reel NC7SZ38L6X MAC06A A6 6-Lead MicroPak, 1.0mm Wide 5k Units on Tape and Reel Package Description Pin Descriptions Supplied As 3k Units on Tape and Reel Logic Symbol Pin Names Description A, B Inputs Y Output NC No Connect Function Table Connection Diagrams Pin Assignments for SC70 and SOT23 Y = AB Inputs IEEE/IEC Output A B Y L L *H L H *H H L *H H H L (Top View) Pad Assignment for MicroPak H = HIGH Logic Level L = LOW Logic Level *H = HIGH Impedance output state (Open Drain) (Top Thru View) TinyLogic is a registered trademark of Fairchild Semiconductor Corporation. MicroPak is a trademark of Fairchild Semiconductor Corporation. © 2004 Fairchild Semiconductor Corporation DS012175 www.fairchildsemi.com NC7SZ38 TinyLogic UHS 2-Input NAND Gate (Open Drain Output) October 1996 NC7SZ38 Absolute Maximum Ratings(Note 1) Recommended Operating Conditions (Note 2) Supply Voltage (VCC ) −0.5V to +6V DC Input Voltage (VIN) −0.5V to +6V Supply Voltage Operating (VCC) DC Output Voltage (VOUT) −0.5V to +6V Supply Voltage Data Retention (VCC) DC Input Diode Current (IIK) 1.65V to 5.5V 1.5V to 5.5V Input Voltage (VIN) 0V to 5.5V @VIN < −0.5V −50 mA Output Voltage (VOUT) @ VIN > 6V +20 mA Operating Temperature (TA) DC Output Diode Current (IOK) 0V to 5.5V −40°C to +85°C Input Rise and Fall Time (tr, tf) @VOUT < −0.5V −50 mA VCC = 1.8V, 2.5V ± 0.2V 0 ns/V to 20 ns/V @ VOUT > 6V, VCC = GND +20 mA VCC = 3.3V ± 0.3V 0 ns/V to 10 ns/V DC Output Current (IOUT) +50 mA VCC = 5.0V ± 0.5V 0 ns/V to 5 ns/V DC VCC/GND Current (ICC/IGND) ±50 mA Thermal Resistance (θJA) −65°C to +150 °C Storage Temperature (TSTG) 150 °C Junction Temperature under Bias (TJ) SOT23-5 300°C/W SC70-5 425°C/W Junction Lead Temperature (T1); 260 °C (Soldering, 10 seconds) Note 1: Absolute maximum ratings are DC values beyond which the device may be damaged or have its useful life impaired. The datasheet specifications should be met, without exception, to ensure that the system design is reliable over its power supply, temperature, and output/input loading variables. Fairchild does not recommend operation outside datasheet specifications. Power Dissipation (PD) @ +85°C SOT23-5 200 mW SC70-5 150 mW Note 2: Unused inputs must be held HIGH or LOW. They may not float. DC Electrical Characteristics Symbol VIH Parameter HIGH Level Input Voltage VIL LOW Level Input Voltage ILKG HIGH Level TA = +25°C VCC (V) Min Typ TA = −40°C to +85°C Max 1.65 to 1.95 0.75 VCC 2.3 to 5.5 LOW Level Output Voltage Max 0.75 VCC 0.7 VCC 0.25 VCC 0.25 VCC 2.3 to 5.5 0.3 VCC 0.3 VCC 5.5 ±5 1.65 0.0 0.1 Units Conditions V 0.7 VCC 1.65 to 1.95 Output Leakage VOL Min ±10 V µA VIN = VIL VOUT = VCC or GND 0.1 1.8 0.0 0.1 0.1 2.3 0.0 0.1 0.1 3.0 0.0 0.1 0.1 V VIN = VIH IOL = 100 µA 4.5 0.0 0.1 0.1 1.65 0.08 0.24 0.24 2.3 0.10 0.3 0.3 3.0 0.15 0.4 0.4 3.0 0.22 0.55 0.55 4.5 0.22 0.55 0.55 ±1 ±10 µA VIN = 5.5V, GND IOL = 8 mA V IOL = 16 mA IOL = 24 mA IOL = 32 mA IIN Input Leakage Current 5.5 IOFF Power Off Leakage Current 0.0 1 10 µA VIN or VOUT = 5.5V ICC Quiescent Supply Current 5.5 2.0 20 µA VIN = 5.5V, GND www.fairchildsemi.com 2 Symbol tPZL tPLZ Parameter Propagation Delay Propagation Delay TA = +25°C VCC TA = −40°C to +85°C Units Conditions (V) Min Typ Max Min Max 1.65 1.5 6.5 12.7 1.5 13.2 1.8 1.5 5.4 10.5 1.5 11.0 2.5 ± 0.2 0.8 3.5 7.0 0.8 7.5 3.3 ± 0.3 0.8 2.8 5.0 0.8 5.2 RD = 500Ω VI = 2 × VCC 5.0 ± 0.5 0.5 2.2 4.3 0.5 4.5 1.65 1.5 5.5 12.7 1.5 13.2 CL = 50 pF ns RU = 500Ω CL = 50 pF 1.8 1.5 4.6 10.5 1.5 11.0 2.5 ± 0.2 0.8 3.0 7.0 0.8 7.5 3.3 ± 0.3 0.8 2.1 5.0 0.8 5.2 RD = 500Ω 5.0 ± 0.5 0.5 1.3 4.3 0.5 4.5 VI = 2 × VCC CIN Input Capacitance 0 4 COUT Output Capacitance 0 5 CPD Power Dissipation 3.3 5.1 Capacitance 5.0 7.3 ns RU = 500Ω Figure Number Figures 1, 3 Figures 1, 3 pF pF (Note 3) Figure 2 Note 3: CPD is defined as the value of the internal equivalent capacitance which is derived from dynamic operating current consumption (ICCD) at no output loading and operating at 50% duty cycle. (See Figure 2.) CPD is related to ICCD dynamic operating current by the expression: ICCD = (C PD) (VCC) (fIN) + (ICC static). AC Loading and Waveforms CL includes load and stray capacitance Input PRR = 1.0 MHz; tw = 500 ns FIGURE 1. AC Test Circuit FIGURE 3. AC Waveforms Input = AC Waveform; tr = tf = 1.8 ns PRR = 10 MHz; Duty Cycle = 50% FIGURE 2. ICCD Test Circuit 3 www.fairchildsemi.com NC7SZ38 AC Electrical Characteristics NC7SZ38 Tape and Reel Specification TAPE FORMAT for SC70 and SOT23 Package Tape Designator M5X, P5X Number Cavity Section Cavities Status Cover Tape Status Leader (Start End) 125 (typ) Empty Sealed Carrier 3000 Filled Sealed Trailer (Hub End) 75 (typ) Empty Sealed TAPE DIMENSIONS inches (millimeters) Package SC70-5 SOT23-5 Tape Size 8 mm 8 mm www.fairchildsemi.com DIM A DIM B 0.093 0.096 (2.35) (2.45) 0.130 0.130 (3.3) (3.3) DIM F DIM Ko 0.138 ± 0.004 0.053 ± 0.004 (3.5 ± 0.10) (1.35 ± 0.10) 0.138 ± 0.002 0.055 ± 0.004 (3.5 ± 0.05) 4 (1.4 ± 0.11) DIM P1 DIM W 0.157 0.315 ± 0.004 (4) (8 ± 0.1) 0.157 0.315 ± 0.012 (4) (8 ± 0.3) TAPE FORMAT for MircoPak Package (Continued) Tape Number Cavity Section Cavities Status Status Leader (Start End) 125 (typ) Empty Sealed Designator L6X Cover Tape Carrier 5000 Filled Sealed Trailer (Hub End) 75 (typ) Empty Sealed N W1 W2 W3 REEL DIMENSIONS inches (millimeters) Tape Size 8 mm A B C D 7.0 0.059 0.512 0.795 2.165 0.331 + 0.059/−0.000 0.567 W1 + 0.078/−0.039 (177.8) (1.50) (13.00) (20.20) (55.00) (8.40 + 1.50/−0.00) (14.40) (W1 + 2.00/−1.00) 5 www.fairchildsemi.com NC7SZ38 Tape and Reel Specification NC7SZ38 Physical Dimensions inches (millimeters) unless otherwise noted 5-Lead SOT23, JEDEC MO-178, 1.6mm Package Number MA05B www.fairchildsemi.com 6 NC7SZ38 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 5-Lead SC70, EIAJ SC-88a, 1.25mm Wide Package Number MAA05A 7 www.fairchildsemi.com NC7SZ38 TinyLogic UHS 2-Input NAND Gate (Open Drain Output) Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 6-Lead MicroPak, 1.0mm Wide Package Number MAC06A Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. www.fairchildsemi.com www.fairchildsemi.com 8