MOTOROLA MMA7260QR2 1.5g - 6g three axis low-g micromachined accelerometer Datasheet

Freescale Semiconductor
Technical Data
MMA7260Q
Rev 0, 04/2005
MMA7260Q
±1.5g - 6g Three Axis Low-g
Micromachined Accelerometer
The MMA7260Q low cost capacitive micromachined accelerometer
features signal conditioning, a 1-pole low pass filter, temperature
compensation and g-Select which allows for the selection among 4
sensitivities. Zero-g offset full scale span and filter cut-off are factory set and
require no external devices. Includes a Sleep Mode that makes it ideal for
handheld battery powered electronics.
MMA7260Q: XYZ AXIS
ACCELEROMETER
±1.5g/2g/4g/6g
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
Selectable Sensitivity (1.5g/2g/4g/6g)
Low Current Consumption: 500 µA
Sleep Mode: 3 µA
Low Voltage Operation: 2.2 V – 3.6 V
6mm x 6mm x 1.45mm QFN
High Sensitivity (800 mV/g @1.5 g)
Fast Turn On Time
High Sensitivity (1.5 g)
Integral Signal Conditioning with Low Pass Filter
Robust Design, High Shocks Survivability
Pb-Free Terminations
Environmentally Preferred Package
Low Cost
Bottom View
16 LEAD
QFN
CASE 1622-01
Typical Applications
Device Name
Temperture Range
Case No.
Package
MMA7260Q
– 20 to +85°C
1622-01
QFN-16, Tube
MMA7260QR2
– 20 to +85°C
1622-01
QFN-16,Tape & Reel
© Freescale Semiconductor, Inc., 2005. All rights reserved.
XOUT
YOUT
ZOUT
16
15
14
13
12 Sleep
Mode
g-Select2
2
11 N/C
VDD 3
10 N/C
VSS 4
9 N/C
5
6
7
8
N/C
1
N/C
g-Select1
N/C
ORDERING INFORMATION
Top View
N/C
HDD MP3 Player : Freefall Detection
Laptop PC : Freefall Detection, Anti-Theft
Cell Phone : Image Stability, Text Scroll, Motion Dialing, E-Compass
Pedometer : Motion Sensing
PDA : Text Scroll
Navigation and Dead Reckoning : E-Compass Tilt Compensation
Gaming : Tilt and Motion Sensing, Event Recorder
Robotics : Motion Sensing
N/C
•
•
•
•
•
•
•
•
Figure 1. Pin Connections
VDD
g-Select1
g-Select2
G-Cell
Sensor
Sleep Mode
Oscillator
Clock
Generator
X-Temp
Comp
XOUT
C to V
Converter
Gain
+
Filter
Y-Temp
Comp
YOUT
Z-Temp
Comp
ZOUT
Control Logic
EEPROM Trim Circuits
VSS
Figure 2. Simplified Accelerometer Functional Block Diagram
Table 1. Maximum Ratings
(Maximum ratings are the limits to which the device can be exposed without causing permanent damage.)
Rating
Symbol
Value
Unit
Maximum Acceleration (all axis)
gmax
±2000
g
Supply Voltage
VDD
–0.3 to +3.6
V
Drop Test(1)
Ddrop
1.8
m
Tstg
–40 to +125
°C
Storage Temperature Range
1. Dropped onto concrete surface from any axis.
ELECTRO STATIC DISCHARGE (ESD)
WARNING: This device is sensitive to electrostatic
discharge.
Although the Freescale accelerometer contains internal
2000 V ESD protection circuitry, extra precaution must be
taken by the user to protect the chip from ESD. A charge of
over 2000 volts can accumulate on the human body or
associated test equipment. A charge of this magnitude can
alter the performance or cause failure of the chip. When
handling the accelerometer, proper ESD precautions should
be followed to avoid exposing the device to discharges which
may be detrimental to its performance.
MMA7260Q
2-2
Sensors
Freescale Semiconductor
Table 2. Operating Characteristics
Unless otherwise noted: –20°C < TA < 85°C, 2.2 V < VDD < 3.6 V, Acceleration = 0g, Loaded output(1)
Characteristic
Symbol
Min
Typ
Max
Unit
Supply Voltage(3)
VDD
2.2
3.3
3.6
V
Supply Current
IDD
—
500
800
µA
Operating Range(2)
Supply Current at Sleep Mode(4)
IDD
—
3
10
µA
TA
–20
—
+85
°C
g-Select1 & 2: 00
gFS
—
±1.5
—
g
g-Select1 & 2: 10
gFS
—
±2.0
—
g
g-Select1 & 2: 01
gFS
—
±4.0
—
g
g-Select1 & 2: 11
gFS
—
±6.0
—
g
Operating Temperature Range
Acceleration Range, X-Axis, Y-Axis, Z-Axis
Output Signal
Zero g (TA = 25°C, VDD = 3.3 V)(5)
Zero g
VOFF
1.485
1.65
1.815
V
VOFF, TA
—
±2
—
mg/°C
Sensitivity (TA = 25°C, VDD = 3.3 V)
S1.5g
740
800
860
mV/g
2g
S2g
555
600
645
mV/g
4g
S4g
277.5
300
322.5
mV/g
6g
S6g
185
200
215
mV/g
S,TA
—
±3
—
%/°C
XY
f-3dB
—
350
—
Hz
Z
f-3dB
—
150
—
Hz
nRMS
—
4.7
—
mVrms
nPSD
—
350
—
µg/ Hz
tRESPONSE
—
1.0
2.0
ms
tENABLE
—
0.5
2.0
ms
XY
fGCELL
—
6.0
—
kHz
Z
fGCELL
—
3.4
—
kHz
fCLK
—
11
—
kHz
VFSO
VSS+0.25
—
VDD–0.25
V
NLOUT
–1.0
—
+1.0
%FSO
VXY, XZ, YZ
—
—
5.0
%
1.5g
Sensitivity
Bandwidth Response
Noise
RMS (0.1 Hz – 1 kHz)(4)
Power Spectral Density RMS (0.1 Hz – 1 kHz)(4)
Control Timing
Power-Up Response Time(6)
Enable Response Time(7)
Sensing Element Resonant Frequency
Internal Sampling Frequency
Output Stage Performance
Full-Scale Output Range (IOUT = 30 µA)
Nonlinearity, XOUT, YOUT, ZOUT
Cross-Axis Sensitivity(8)
1. For a loaded output, the measurements are observed after an RC filter consisting of a 1.0 kΩ resistor and a 0.1 µF capacitor to ground.
2. These limits define the range of operation for which the part will meet specification.
3. Within the supply range of 2.2 and 3.6 V, the device operates as a fully calibrated linear accelerometer. Beyond these supply limits the device
may operate as a linear device but is not guaranteed to be in calibration.
4. This value is measured with g-Select in 1.5g mode.
5. The device can measure both + and – acceleration. With no input acceleration the output is at midsupply. For positive acceleration the output
will increase above VDD/2. For negative acceleration, the output will decrease below VDD/2.
6. The response time between 10% of full scale Vdd input voltage and 90% of the final operating output voltage.
7. The response time between 10% of full scale Sleep Mode input voltage and 90% of the final operating output voltage.
8. A measure of the device’s ability to reject an acceleration applied 90° from the true axis of sensitivity.
MMA7260Q
Sensors
Freescale Semiconductor
2-3
PRINCIPLE OF OPERATION
The Freescale accelerometer is a surface-micromachined
integrated-circuit accelerometer.
The device consists of two surface micromachined
capacitive sensing cells (g-cell) and a signal conditioning
ASIC contained in a single integrated circuit package. The
sensing elements are sealed hermetically at the wafer level
using a bulk micromachined cap wafer.
The g-cell is a mechanical structure formed from
semiconductor materials (polysilicon) using semiconductor
processes (masking and etching). It can be modeled as a set
of beams attached to a movable central mass that move
between fixed beams. The movable beams can be deflected
from their rest position by subjecting the system to an
acceleration (Figure 3) .
As the beams attached to the central mass move, the
distance from them to the fixed beams on one side will
increase by the same amount that the distance to the fixed
beams on the other side decreases. The change in distance
is a measure of acceleration.
The g-cell beams form two back-to-back capacitors
(Figure 3). As the center beam moves with acceleration, the
distance between the beams changes and each capacitor's
value will change, (C = Aε/D). Where A is the area of the
beam, ε is the dielectric constant, and D is the distance
between the beams.
The ASIC uses switched capacitor techniques to measure
the g-cell capacitors and extract the acceleration data from
the difference between the two capacitors. The ASIC also
signal conditions and filters (switched capacitor) the signal,
providing a high level output voltage that is ratiometric and
proportional to acceleration.
Acceleration
SPECIAL FEATURES
g-Select
The g-Select feature allows for the selection among 4
sensitivities present in the device. Depending on the logic
input placed on pins 1 and 2, the device internal gain will be
changed allowing it to function with a 1.5g, 2g, 4g, or 6g
sensitivity (Table 3). This feature is ideal when a product has
applications requiring different sensitivities for optimum
performance. The sensitivity can be changed at anytime
during the operation of the product. The g-Select1 and gSelect2 pins can be left unconnected for applications
requiring only a 1.5g sensitivity as the device has an internal
pulldown to keep it at that sensitivity (800mV/g).
Table 3. g-Select pin Descriptions
g-Select2
g-Select1
g-Range
Sensitivity
0
0
1.5g
800mV/g
0
1
2g
600mV/g
1
0
4g
300mV/g
1
1
6g
200mV/g
Sleep Mode
The 3 axis accelerometer provides a Sleep Mode that is
ideal for battery operated products. When Sleep Mode is
active, the device outputs are turned off, providing significant
reduction of operating current. A low input signal on pin 12
(Sleep Mode) will place the device in this mode and reduce
the current to 3uA typ. For lower power consumption, it is
recommended to set g-Select1 and g-Select2 to 1.5g mode.
By placing a high input signal on pin 12, the device will
resume to normal mode of operation.
Filtering
The 3 axis accelerometer contains onboard single-pole
switched capacitor filters. Because the filter is realized using
switched capacitor techniques, there is no requirement for
external passive components (resistors and capacitors) to set
the cut-off frequency.
Figure 3. Simplified Transducer Physical Model
Ratiometricity
Ratiometricity simply means the output offset voltage and
sensitivity will scale linearly with applied supply voltage. That
is, as supply voltage is increased, the sensitivity and offset
increase linearly; as supply voltage decreases, offset and
sensitivity decrease linearly. This is a key feature when
interfacing to a microcontroller or an A/D converter because
it provides system level cancellation of supply induced errors
in the analog to digital conversion process.
MMA7260Q
2-4
Sensors
Freescale Semiconductor
BASIC CONNECTIONS
PCB Layout
Pin Descriptions
XOUT
YOUT
ZOUT
16
15
14
13
g-Select1 1
POWER SUPPLY
VDD
12 Sleep Mode
C
C
VRH
VDD
P0
VSS
11 NC
VDD 3
10 NC
g-Select1
P1
g-Select2
P2
VSS 4
5
6
7
8
NC
NC
NC
NC
9 NC
Figure 4. Pinout Description
Table 4. Pin Descriptions
Accelerometer
g-Select2 2
VSS
Sleep Mode
XOUT
R
YOUT
R
ZOUT
R
C
C
C
A/DIN
C
Microcontroller
NC
Top View
A/DIN
A/DIN
Pin No.
Pin Name
1
g-Select1
Logic input pin to select g level.
2
g-Select2
Logic input pin to select g level.
3
VDD
Power Supply Input
4
VSS
Power Supply Ground
5-7
N/C
No internal connection.
Leave unconnected.
8 - 11
N/C
Unused for factory trim.
Leave unconnected.
2. Physical coupling distance of the accelerometer to
the microcontroller should be minimal.
12
Sleep Mode
Logic input pin to enable product or
Sleep Mode.
3. Flag underneath package is connected to ground.
13
ZOUT
Z direction output voltage.
14
YOUT
Y direction output voltage.
15
XOUT
X direction output voltage.
16
N/C
Logic
Inputs
Description
No internal connection.
Leave unconnected.
NOTES:
1. Use 0.1 µF capacitor on VDD to decouple the power
source.
4. Place a ground plane beneath the accelerometer to
reduce noise, the ground plane should be attached to
all of the open ended terminals shown in Figure 6.
5. Use an RC filter with 1.0 kΩ and 0.1 µF on the
outputs of the accelerometer to minimize clock noise
(from the switched capacitor filter circuit).
6. PCB layout of power and ground should not couple
power supply noise.
1
g-Select1
ZOUT
13
1 kΩ
0.1 µF
2 g-Select2
VDD
Figure 6Recommended PCB Layout for Interfacing
Accelerometer to Microcontroller
MMA7260Q
3
VDD
YOUT
14
0.1 µF
1 kΩ
7. Accelerometer and microcontroller should not be a
high current path.
8. A/D sampling rate and any external power supply
switching frequency should be selected such that
they do not interfere with the internal accelerometer
sampling frequency (11 kHz for the sampling
frequency). This will prevent aliasing errors.
0.1 µF
4
12
VSS
XOUT 15
Sleep Mode
Logic
Input
1 kΩ
0.1 µF
Figure 5. Accelerometer with Recommended
Connection Diagram
MMA7260Q
Sensors
Freescale Semiconductor
2-5
DYNAMIC ACCELERATION
Top View
+Y
14
13
12
2
11
3
10
4
9
5
6
7
-X
-Z
Bottom
+X
15
1
Top
16
Side View
+Z
8
-Y
: Arrow indicates direction of mass movement.
16-Pin QFN Package
STATIC ACCELERATION
Direction of Earth’s gravity field.*
Top View
Side View
XOUT@ 0g = 1.65 V
YOUT @ -1g = 0.85 V
ZOUT @ 0g = 1.65 V
XOUT @ +1g = 2.45 V
YOUT @ 0g = 1.65 V
ZOUT @ 0g = 1.65 V
XOUT @ 0g = 1.65 V
YOUT @ 0g = 1.65 V
ZOUT @ +1g = 2.45 V
XOUT @ -1g = 0.85 V
YOUT @ 0g = 1.65 V
ZOUT @ 0g = 1.65 V
XOUT @ 0g = 1.65 V
YOUT @ 0g = 1.65 V
ZOUT @ -1g = 0.85 V
XOUT @ 0g = 1.65 V
YOUT @ +1g = 2.45 V
ZOUT @ 0g = 1.65 V
* When positioned as shown, the Earth’s gravity will result in a positive 1g output.
MMA7260Q
2-6
Sensors
Freescale Semiconductor
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the total
design. The footprint for the surface mount packages must be
the correct size to ensure proper solder connection interface
between the board and the package.
With the correct footprint, the packages will self-align when
subjected to a solder reflow process. It is always
recommended to design boards with a solder mask layer to
avoid bridging and shorting between solder pads.
6.0
0.55
4.25
9
6.0
8
13
12
5
16
0.50
1.00
1
Pin 1 ID (non metallic)
4
Solder areas
MMA7260Q
Sensors
Freescale Semiconductor
2-7
PACKAGE DIMENSIONS
6
PIN 1
INDEX AREA
DETAIL G
A
M
0.1 C
2X
0.10 C
0.08 C
1.45±0.1
5
6
(0.203)
(0.102)
C
SEATING PLANE
DETAIL G
2X
M
0.10 C
B
(0.5)
(1)
4
0.1 C A B
16X
4.24
4.04
EXPOSED DIE
ATTACH PAD
13
VIEW ROTATED 90˚ CLOCKWISE
(45˚)
0.1
DETAIL M
PIN 1 INDEX
16
DETAIL M
12
4.24
4.04
1
0.5
0.1 C A B
9
4
12X
8
16X
1
5
0.63
0.43
16X
VIEW M-M
0.60
0.40
0.1
M
C A B
0.05
M
C
3
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETERS.
2. INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.5M, 1994.
3. THIS DIMENSION APPLIES TO METALLIZED
TERMINAL AND IS MEASURED BETWEEN 0.25MM
AND 0.30MM FROM TERMINAL TIP.
4. THIS DIMENSION REPRESENTS TERMINAL FULL
BACK FROM PACKAGE EDGE UP TO 0.1MM IS
ACCEPTABLE.
5. COPLANARITY APPLIES TO THE EXPOSED HEAT
SLUG AS WELL AS THE TERMINAL.
6. RADIUS ON TERMINAL IS OPTIONAL.
7. MINIMUM METAL GAP 0.2MM.
CASE 1622-01
ISSUE O
MMA7260Q
2-8
Sensors
Freescale Semiconductor
NOTES
MMA7260Q
Sensors
Freescale Semiconductor
2-9
NOTES
MMA7260Q
2-10
Sensors
Freescale Semiconductor
NOTES
MMA7260Q
Sensors
Freescale Semiconductor
2-11
How to Reach Us:
Home Page:
www.freescale.com
E-mail:
[email protected]
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
+1-800-521-6274 or +1-480-768-2130
[email protected]
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
[email protected]
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064
Japan
0120 191014 or +81 3 5437 9125
[email protected]
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
+800 2666 8080
[email protected]
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447 or 303-675-2140
Fax: 303-675-2150
[email protected]
MMA7260Q
Rev. 0
04/2005
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of any
product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters that may be
provided in Freescale Semiconductor data sheets and/or specifications can and do vary
in different applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Semiconductor was negligent regarding the design or manufacture of the part.
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
All other product or service names are the property of their respective owners.
© Freescale Semiconductor, Inc. 2005. All rights reserved.
Similar pages