Dual Digital BTSC Encoder with Integrated DAC AD71028 FEATURES PRODUCT OVERVIEW 2 complete independent BTSC encoders Pilot tone generator Includes subcarrier modulation Typical 23 dB to 27 dB separation, 16 dB minimum Signal bandwidth of 14 kHz Phat-StereoTM algorithm for stereo image enhancement Dialog enhancement function for playing wide dynamic range video sources over built-in TV speakers Includes L-R dual-band compressor SPI® port for control of modes and effects Differential output for optimum performance DAC performance: 92 dB dynamic range, –92 dB THD+N Output level control for setting aural carrier deviation Flexible serial data port with right-justified, left-justified, I2S compatible, and DSP serial port modes 48-lead LQFP plastic package The AD71028 dual digital BTSC encoder provides two complete digital BTSC encoder channels, including the pilot-tone generation and subcarrier mixing functions. Two built-in high performance DACs are provided to output the BTSC baseband composite signal. The output of the AD71028 can be connected with minimal external circuitry to the input of a 4.5 MHz aural FM modulator. APPLICATIONS In addition to the BTSC encoders, the AD71028 also includes a stereo image enhancement function, Phat Stereo, to increase the sense of spaciousness available from closely spaced TV loudspeakers. A dialog enhancement algorithm is also included to solve the problem of playing wide dynamic range sources over limited-performance TV speakers and amplifiers. An extensive SPI port allows click-free parameter updates. The AD71028 also includes ADI’s patented multibit Σ-∆ DAC architecture. This architecture provides 92 dB SNR and THD+N of –92 dB. Digital set-top box BTSC encoder FUNCTIONAL BLOCK DIAGRAM 3 SERIAL INPUT PLL DIVIDERS CLOCK DOUBLER CLOCK SIGNAL GROUP CLOCK DOUBLER PLL DIVIDERS SERIAL INPUT B SPI I/O GROUP SERIAL INPUT 3 4 SPI PORT BTSC ENCODER CORE A BTSC ENCODED OUTPUT A DAC ANALOG BIAS BIAS BTSC ENCODER CORE B BTSC ENCODED OUTPUT B DAC CONTROL REGISTERS PARAMETER RAM AD71028 04482-0-001 SERIAL INPUT A Figure 1. Functional Block Diagram Rev. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.326.8703 © 2004 Analog Devices, Inc. All rights reserved. AD71028 TABLE OF CONTENTS Specifications..................................................................................... 3 Input Levels ................................................................................. 11 DAC Analog Performance........................................................... 3 Clock Relationships.................................................................... 11 BTSC Encoder Performance ....................................................... 3 SPI Port ............................................................................................ 12 Digital I/O ..................................................................................... 3 Overview ..................................................................................... 12 Power.............................................................................................. 4 SPI Address Decoding ............................................................... 12 Temperature Range ...................................................................... 4 Parameter RAM.......................................................................... 13 Digital Timing............................................................................... 4 Control Register ......................................................................... 13 Absolute Maximum Ratings............................................................ 5 Output Level Register ................................................................ 13 Pin Configuration and Functional Descriptions.......................... 6 Stereo Enhancement Register ................................................... 13 Features .............................................................................................. 8 Dialog Enhancement Register .................................................. 13 Pin Functions ................................................................................ 8 SPI Read/Write Data Formats .................................................. 14 Signal Processing ............................................................................ 10 Initialization ................................................................................ 14 Background of BTSC ................................................................. 10 Serial Data Input Port ................................................................ 14 Performance Factors .................................................................. 10 Analog Output Section .................................................................. 16 Separation Alignment ................................................................ 10 Outline Dimensions ....................................................................... 17 Phase Linearity of the External Analog Filter......................... 11 Ordering Guide .......................................................................... 17 REVISION HISTORY Revision 0: Initial Version Rev. 0 | Page 2 of 20 AD71028 SPECIFICATIONS TEST CONDITIONS, UNLESS OTHERWISE NOTED 5.0 V Supply Voltages (AVDD, DVDD) Ambient Temperature 25°C Input Clock 12.288 MHz Input Signal 1 kHz, 0 dBFS Input Sample Rate 48 kHz Measurement Bandwidth 20 Hz to 14 kHz Word Width 24 Bits Load Capacitance 50 pF Input Voltage HI 2.4 V Input Voltage LO 0.4 V DAC ANALOG PERFORMANCE Table 1. Parameter Resolution Dynamic Range (20 Hz to 14 kHz, –60 dB Input) (Encoded Output, Left = Right) Total Harmonic Distortion + Noise (Encoded Output, Left = Right, 20 Hz to 14 kHz) VIN = 0 dB Differential Output Range (± Full Scale, Left = Right) Min 85 –85 Typ 24 921 Max –921 1.7 Unit Bits dB dB V p-p 1 Measurement of encoded BTSC signal, not a measurement of end-to-end system. BTSC ENCODER PERFORMANCE Table 2. Parameter Channel Separation1 30 Hz to 500 Hz 500 Hz to 5 kHz 5 kHz to 13.5 kHz Frequency Response1 30 Hz to 10 kHz 30 Hz to 13.5 kHz Min Typ Max Unit 27 23 16 dB dB dB +0.5 +0.5 –1.0 –1.5 dB dB 1 These specifications are measured with a –25 dB, 1 kHz input signal. DIGITAL I/O Table 3. Parameter Input Voltage HI (VIH) Input Voltage LO (VIL) Input Leakage (IIH @ VIH = 2.4 V) Input Leakage (IIL @ VIL = 0.8 V) High Level Output Voltage (VOH) IOH = 2 mA Low Level Output Voltage (VOL) IOL = 2 mA Min 2.1 Typ Max 0.8 10 10 DVDD – 0.5 0.4 Rev. 0 | Page 3 of 20 Unit V V µA µA V V AD71028 POWER Table 4. Parameter Supplies Voltage, Analog and Digital Analog Current Digital Current Dissipation Operation—Both Supplies Operation—Analog Supplies Operation—Digital Supplies Min Typ Max Unit 4.5 5 31 97 5.5 37 110 V mA mA 640 155 485 mW mW mW TEMPERATURE RANGE Table 5. Parameter Specifications Guaranteed Functionality Guaranteed Storage Min Typ 25 0 –55 Max Unit °C °C °C 70 +125 DIGITAL TIMING Table 6. Parameter tDMD tDBL tDBH tDLS tDLH tDDS tDDH tCCL tCCH tCLS tCLH tCLD tCDS tCDH tRLP MCLK Recommended Duty Cycle @ 12.288 MHz (256 × fS and 512 × fS Modes) BCLK Low Pulse Width BCLK High Pulse Width LRCLK Setup LRCLK Hold SDATA Setup SDATA Hold CCLK Low Pulse Width CCLK High Pulse Width CLATCH Setup CLATCH Hold CLATCH High Pulse Width CDATA Setup CDATA Hold Reset LO Pulse Width Rev. 0 | Page 4 of 20 Min 40 25 10 0 10 0 10 10 10 10 20 10 0 10 10 Typ Max 60 Unit % ns ns ns ns ns ns ns ns ns ns ns ns ns ns AD71028 ABSOLUTE MAXIMUM RATINGS Table 7. AD71028 Stress Ratings Parameter DVDD to DGND ODVDD to DGND AVDD to AGND Digital Inputs Analog Inputs AGND to DGND Reference Voltage Maximum Junction Temperature Storage Temperature Range Soldering Min –0.3 –0.3 –0.3 DGND – 0.3 AGND – 0.3 –0.3 –65 Table 8. Package Characteristics (48-Lead LQFP) Max +6 +6 +6 DVDD + 0.3 AVDD + 0.3 +0.3 (AVDD + 0.3)/2 Unit V V V V V V V 125 °C +150 300 10 °C °C sec Parameter θJA Thermal Resistance [Junction-to-Ambient] θJC Thermal Resistance [Junction-to-Case] Min Typ Max Unit 72 °C/W 19.5 °C/W Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. 0 | Page 5 of 20 AD71028 48 47 46 45 44 43 42 41 40 39 REFCAP FILTCAP NC CLK27_PA CLK27_PB PLL_PA MCLK_PA DGND DVDD PLL_PB MCLK_PB DIV1_PA PIN CONFIGURATION AND FUNCTIONAL DESCRIPTIONS 38 37 DIV2_PA 1 36 AGND DIV1_PB 2 35 OUTB– DIV2_PB 3 34 OUTB+ NC 4 33 AVDD NC 5 32 AGND AD71028 DGND 6 31 AVDD TOP VIEW (Not to Scale) DVDD 7 30 OUTA+ 29 OUTA– ODVDD 8 NC 9 28 AGND NC 10 27 NC COUT 11 26 NC CDATA 12 04482-0-002 LRCLK_PB BCLK_PB SDATA_PB LRCLK_PA 20 21 22 23 24 BCLK_PA SDATA_PA DVDD RESETB CCLK DGND 17 18 19 CLATCH 14 15 16 DVDD 25 DOUBLE 13 NC = NO CONNECT Figure 2. 48-Lead Low Profile Quad Flat Pack (LQFP) Table 9. Pin Function Descriptions Pin No. 1 2 3 4, 5, 9, 10, 26, 27, 39 6, 16, 44 7, 13, 17, 45 8 11 12 14 15 18 19 20 21 22 23 24 25 28, 32, 36 29 30 31, 33 34 35 37 38 Mnemonic DIV2_PA DIV1_PB DIV2_PB NC DGND DVDD ODVDD COUT CDATA CCLK CLATCH RESETB SDATA_PA BCLK_PA LRCLK_PA SDATA_PB BCLK_PB LRCLK_PB DOUBLE AGND OUTA– OUTA+ AVDD OUTB+ OUTB– REFCAP FILTCAP Input/Output OUT OUT OUT OUT IN IN IN IN IN IN IN IN IN IN IN OUT OUT OUT OUT IN IN Description CLK27_PA clock (Pin 40) Divided by 1125 PLL_PB Clock (Pin 46) Divided by 512 (DOUBLE = 1) or 1024 (DOUBLE = 0) CLK27_PB Clock (Pin 41) Divided by 1125 No Connection Digital Ground Digital Supply for DSP Core Digital Supply for Output Buffers SPI Readback SPI Control Data Input SPI Serial Bit Clock SPI Control Latch Signal Reset Signal for Both Processors, Active Low Data Input to Processor A Bit Clock Signal for Serial Data Input to Processor A Left/Right Framing Signal for Data Input to Processor A Data Input to Processor B Bit Clock Signal for Serial Data Input to Processor B Left/Right Framing Signal for Data Input to Processor B Enables Internal Clock Doubler for 12.288 MHz Input (Both Processors) Analog Ground Negative Analog Output, Processor A Positive Analog Output, Processor A Analog Supply Positive Analog Output, Processor B Negative Analog Output, Processor B Connection Point for 10 µF VREF Filter Capacitor Connection for Noise Reduction Capacitor Rev. 0 | Page 6 of 20 AD71028 Pin No. 40 41 42 43 46 47 48 Mnemonic CLK27_PA CLK27_PB PLL_PA MCLK_PA PLL_PB MCLK_PB DIV1_PA Input/Output IN IN IN IN IN IN OUT Description Input for 27 MHz Video Reference Clock, Processor A Input for 27 MHz Video Reference Clock, Processor B Input from External PLL, Processor A Clock Input to Processor A Input from External PLL, Processor B Clock Input to Processor B PLL_PA Clock (Pin 42) Divided by 512 (DOUBLE = 1) or 1024 (DOUBLE = 0) Rev. 0 | Page 7 of 20 AD71028 FEATURES The AD71028 is comprised of two independent digital-input BTSC encoders. The two processors allow two completely asynchronous BTSC channels to be encoded, each with its own clock signals. Figure 1 shows the block diagram of the device. Signal processing parameters are stored in a 256-location parameter RAM, which is initialized on power-up by an internal boot ROM. The values stored in the parameter RAM control all the filter coefficients, mixing, and dynamics processing code used in the BTSC algorithm. The AD71028 has an SPI port that supports complete read/ write capability of the parameter RAM, as well as a control port and several other registers that allow the various signal processing parameters to be controlled. The AD71028 can run as a standalone processor without SPI control. The AD71028 has a very flexible serial data input port that allows for glueless interconnection to a variety of signal sources. The AD71028 can be configured in left-justified, I2S, rightjustified, or DSP serial port compatible modes. It can support 16, 20, and 24 bits in all modes. The AD71028 accepts serial audio data in MSB first, twos complement format. The AD71028 operates from a single 5 V power supply. It is fabricated on a single monolithic integrated circuit and is housed in a 48-lead LQFP package for operation over the 0°C to 70°C temperature range. PIN FUNCTIONS Pin names and functions are shown below. Note that pins with a “_PA” designation are connected to Processor A, while those with a “_PB” designation are connected to Processor B. All input pins have a logic threshold compatible with TTL input levels, and may therefore be used in systems with 3.3 V logic. All digital output levels are controlled by the ODVDD pin, which may range from 2.7 V to 5.5 V, for compatibility with a wide range of external devices. LRCLK_PA, LRCLK_PB Left/right clocks for framing the input data. The interpretation of the LRCLK changes according to the serial mode, set by writing to the control registers. BCLK_PA, BCLK_PB Serial bit clocks for clocking in the serial data. The interpretation of BCLK changes according to the serial mode, which is set by writing to the control registers. SDATA_PA, SDATA_PB Serial data inputs to each processor. The serial format is selected by writing to Bits <3:0> of the control registers. MCLK_PA, MCLK_PB Master clock inputs. The master clock frequency must be either 256 × fS or 512 × fS, where fS is the input sampling frequency. If the DOUBLE pin is high, an internal clock doubler is used to take a 256 × fS input clock and produce the 512 × fS internal clock required by the DSP core. If the DOUBLE pin is low, the frequency of the input clock must be set to 512 × fS. In case these clock signals are not available, a simple external PLL may be used to generate the master clock signals. On-chip dividers are provided to simplify this task. CDATA Serial data in for the SPI control port. See the SPI Port section for more information on SPI port timing. COUT Serial data output. This is used for reading back registers and memory locations. It is three-stated when an SPI read is not active. See the SPI Port section for more information on SPI port timing. CCLK SPI bit-rate clock. This pin may either run continuously or be gated in between SPI transactions. See the SPI Port section for more information on SPI port timing. CLATCH SPI latch signal. This signal must go low at the beginning of an SPI transaction and high at the end of a transaction. Each SPI transaction may take a different number of CCLKs to complete, depending on the address and read/write bit that are sent at the beginning of the SPI transaction. Detailed SPI timing information can be found in the SPI Port section. RESETB Active-low reset signal. After RESETB transitions from low to high, the AD71028 goes through an initialization sequence where the parameter RAMs are initialized with the contents of the on-board boot ROM. All SPI registers are set to 0, and the data RAMs are also zeroed. The initialization is complete after 1024 MCLK cycles. New values should not be written to the SPI port until the initialization is complete. DOUBLE When this pin is set high, the internal clock doubler is turned on so a 256 × fS MCLK can be input to the AD71028. PLL_PA, PLL_PB PLL clock input pins for Processor A and Processor B. These pins are connected to an internal divide-by-1024 circuit (or divide-by-512 if DOUBLE is high). This makes it possible to use an inexpensive external PLL to generate the system clock. If an external PLL is used, this pin should also be connected to the appropriate MCLK_PA or MCLK_PB pin. Rev. 0 | Page 8 of 20 AD71028 CLK27_PA, CLK27_PB DVDD Input pins to the divide-by-1125 block. If an external PLL is used to generate the audio master clock, the 27 MHz video master clock may be applied to these pins where it is divided by 1125 to produce a 24 kHz feedback clock to the external PLL phase detector. Digital VDD for core. 5 V nominal. DIV1_PA, DIV1_PB Digital ground. Output of divide-by-1024 circuit. Divides the master clock signal by 1024 (or 512 when DOUBLE is asserted). Used to interface to external PLL. AVDD ODVDD Digital VDD for all digital outputs. Variable from 2.7 V to 5.5 V. DGND Analog VDD. 5 V nominal. Bypass capacitors should be placed close to the pins and connected directly to the analog ground plane. DIV2_PA, DIV2_PB Output of divide-by-1125 circuit. Divides the master-clock signal by 1125. Used to interface to external PLL. The output signal is a pulse with a duration of one master clock, and should therefore be used with edge-triggered phase detectors. REFCAP Analog reference voltage input. The nominal REFCAP input voltage is 2.5 V; the analog gain scales directly with the voltage on this pin. Any ac signal on this pin will cause distortion, and therefore a large decoupling capacitor should be used to ensure that the voltage on REFCAP is clean. The input impedance of REFCAP is greater than 1 MΩ. AGND Analog ground. OUTA+, OUTA– Differential analog outputs for Processor A. The nominal output voltage for a 1 kHz 0 dB mono input signal is 600 mV rms. This level may be adjusted by writing to SPI location 258. OUTB+, OUTB– Differential analog outputs for Processor B. The nominal output voltage for a 1 kHz 0 dB mono input signal is 600 mV rms. This level may be adjusted by writing to SPI location 770. FILTCAP Filter cap point. This pin is used to reduce the noise on an internal biasing point in order to provide the highest performance. It may not be necessary to connect this pin, depending on the quality of the layout and grounding used in the application circuit. Rev. 0 | Page 9 of 20 AD71028 SIGNAL PROCESSING L–R COMPRESSOR L OSCILLATOR L+R 2× Fh CARRIER Fh PILOT TO DAC 04482-0-003 MATRIX R 75µs PRE-EMPHASIS FILTER Figure 3. Signal Processing Flow BACKGROUND OF BTSC PERFORMANCE FACTORS BTSC is the name of the standard for adding stereo audio capability to the US television system. It is in many ways similar to the algorithm used for FM stereo broadcasts, with the addition of a sophisticated compressor circuit to improve the signal-to-noise ratio. In order to maintain good separation between left and right, it is necessary to closely match the filtering and companding standards set forth in the standard (FCC OET60). Even small errors can result in poor performance. The AD71028 has been programmed to match these standards as accurately as possible. Separation typically ranges from 30 dB at frequencies below 1 kHz to 15 dB at 14 kHz. Measuring these numbers can be difficult as significant differences exist between many so-called reference decoders, which are all implemented with analog components. The processing of mono (L = R) signals is unchanged from the original pre-BTSC system in order to maintain compatibility with non-BTSC TV receivers. The L + R signal is applied to a 75 µs pre-emphasis filter, and is then applied to a 4.5 MHz FM modulator, which is later added into the video signal to create a composite video signal. Stereo capability is added by taking the L–R signal, applying it to a 2-band dynamic compressor, and then multiplying this signal by a carrier signal at twice the horizontal scanning rate (Fh), or about 2 × 15.734 kHz. This multiplication is known as double-sideband suppressed-carrier modulation, and it effectively translates the compressed L – R spectrum up in frequency so that it sits above the audio band (Figure 3). In order for the receiver to recover this L – R signal, a pilot tone at the horizontal rate is added to the signal. The receiver has a PLL that locks to this pilot and generates a signal at the carrier frequency. This signal is then used to multiply the composite BTSC-encoded signal, which translates this component back down to baseband. The L – R signal is then applied to a 2-band expander, which is the complement to the earlier compressor step. Once the L + R and L – R signals are recovered, a simple addition/subtraction circuit (sometimes referred to as the “matrix”) can be used to recover the L and R signal. Since the pilot tone is added at 15.734 kHz, it is necessary to reduce the signal’s bandwidth so that audio signals cannot interfere with the pilot tone. In the AD71028, the bandwidth is limited to 14 kHz; above this frequency, the response decays very rapidly. SEPARATION ALIGNMENT The BTSC encoder outputs are all specified in terms of the deviation of the FM 4.5 MHz carrier. For the AD71028, a digital input level of 0 dB (mono signal) should cause a carrier deviation of ±25 kHz without the 75 µs pre-emphasis filter. In practice, the pre-emphasis filter may be left in for this adjustment, as long as the frequency is low enough to not be affected by the pre-emphasis filter. It is critical to maintain the proper gain relationship between the BTSC encoder and the 4.5 MHz FM modulator. A common mistake is to assume that changing the gain between the BTSC encoder output and the FM modulator input has the same effect as changing the audio input level going in to the BTSC encoder. The presence of a complicated 2-band nonlinear dynamics processor means that the encoder output must be connected to the decoder input (through the FM modulation/demodulation process) with a known gain. If this gain is changed, the separation will significantly suffer. When measuring the AD71028 on the bench, it is possible to use a BTSC reference decoder box, so that the FM modulation/ demodulation process may be skipped. These units have a method of adjusting the input voltage sensitivity to achieve best separation. The output level of the AD71028 can also be adjusted over a wide range using either the SPI control port or by adjusting the values of the components used in the external analog low-pass filter that is between the BTSC encoder output and the input to the FM modulator. Rev. 0 | Page 10 of 20 AD71028 PHASE LINEARITY OF THE EXTERNAL ANALOG FILTER If the time alignment of the pilot to the carrier signal is not close to 0 degrees, a loss of separation can occur. This means that the external analog low-pass filter should be a linear-phase design to provide constant group delay over the range from dc to 50 kHz. Bessel filters are recommended for this application. Figure 12 shows a recommended design for these filters. INPUT LEVELS The maximum input level to the AD71028 changes across frequency. Table 10 shows the maximum allowable input level for different frequencies. These values are part of the BTSC specification and are not a function of this chip. Table 10. Maximum Input Levels to the BTSC Encoder across Frequency Frequency (Hz) 20 to 1000 1600 2500 3150 5000 8000 12500 Maximum Input Level (dBFS) 0 dB –1 dB –3 dB –5 dB –8 dB –11 dB –15 dB The AD71028 contains a clock doubler circuit that may be used to generate an internal 512 × fS clock when the external clock is 256 × fS. The clock mode is set by connecting the DOUBLE pin either high or low. This pin should be tied either high or low and should not be changed after power-up. The AD71028 requires a master clock at either 256 × 48 kHz (12.288 MHz) when DOUBLE = 1 or 512 × 48 kHz (24.576 MHz) when DOUBLE = 0. In some cases, this signal is provided by the MPEG decoder chip itself. In other cases, only the 27 MHz video clock may be available. In this case, the AD71028 provides on-chip dividers to interface to an external PLL such as the 74HC4046. Figure 4 shows the circuit to accomplish this. The 27 MHz clock is applied to the AD71028 and divided down by 1125, producing a signal at 24 kHz. The PLL oscillator output is divided down by 512, producing a 24 kHz output (when locked). These two signals are applied to the phase-comparator inputs of the external PLL. Note that the divided-down 27 MHz signal looks like a pulse with a duration of one master clock, and therefore only edge-triggered phase detectors should be used. AD71028 27MHz IN DIVIDE-BY-1125 74HC4046 DIVIDE-BY-512 CLOCK RELATIONSHIPS a) 27 MHz/Fh = 1716 = 2 × 2 × 3 × 11 × 13 DSP 04482-0-004 In an MPEG receiver architecture, all clocks are typically generated from a 27 MHz master clock. The following integer relationships are found between the clocks, with Fh = 15.734 kHz: Figure 4. PLL Connections for 27 MHz Master Clock b) Fh/2 = Fcolor_subcarrier/(5 × 7 × 13) c) 27 MHz/Fcolor_subcarrier = (5 × 7)/(2 × 2 × 2 × 3 × 11) d) 27 MHz/48 kHz = 1125/2 Rev. 0 | Page 11 of 20 AD71028 SPI PORT CLATCH BYTE 1 BYTE 0 CDATA 04482-0-005 CCLK BYTE 4 Figure 5. Sample of SPI Write Format (Single-Write Mode) CLATCH CCLK BYTE 1 XXX HI-Z DATA COUT DATA DATA HI-Z 04482-0-006 BYTE 0 CDATA Figure 6. Sample of SPI Read Format (Single-Read Mode) OVERVIEW The AD71028 can be controlled using the SPI port. In general, there are three parameters per processor that can be controlled: the encoder output level, the Phat Stereo image enhancement algorithm, and the dialog enhancement algorithm. It is also possible to write new data into the parameter RAM to alter the filter coefficients used in the BTSC encoding process. This is a fairly complex topic unnecessary for normal operation of the chip, and the details are not included in this data sheet. Please contact ADI if modifications to the BTSC filters are required. The SPI port uses a 4-wire interface consisting of CLATCH, CCLK, CDATA, and COUT signals. The CLATCH signal goes low at the beginning of a transaction and high at the end of a transaction. The CCLK signal latches the serial input data on a low-to-high transition. The CDATA signal carries the serial input data, and the COUT signal is the serial output data. The COUT signal remains three-stated until a READ operation is requested. This allows other SPI compatible peripherals to share the same readback line. All SPI transactions follow the same basic format, shown in Figure 5. Figure 6 shows the read format. The Wb/R bit is low for a write and high for a read operation. The 10-bit address word is decoded into either a location in the parameter RAM or one of the SPI registers. The number of data bytes varies according to the register or memory being accessed. The detailed data format diagram for continuous-mode operation is given in the SPI Read/Write Data Formats section. SPI ADDRESS DECODING Table 11 shows the address decoding used in the SPI port. The SPI address space encompasses a set of registers and the parameter RAM. The parameter RAM is loaded on power-up from an on-board boot ROM. Table 11. SPI Port Address Decoding SPI Address 0–255 256 257 258 259 260 512–767 768 769 770 771 772 Register Name Parameter RAM Processor A SPI Control Register Processor A Reserved Output Level Processor A Stereo Spreading Control Processor A Dialog Enhancement Control Processor A Parameter RAM Processor B SPI Control Register Processor B Reserved Output Level Processor B Stereo Spreading Control Processor B Dialog Enhancement Control Processor B Rev. 0 | Page 12 of 20 Read/Write Word Length Write: 22 Bits, Read: 22 Bits Write: 11 Bits, Read: N/A Write: 22 Bits, Read: N/A Write: 22 Bits, Read: N/A Write: 22 Bits, Read: N/A Write: 22 Bits, Read: 22 Bits Write: 22 Bits, Read: N/A Write: 22 Bits, Read: N/A Write: 22 Bits, Read: N/A Write: 22 Bits, Read: N/A AD71028 PARAMETER RAM OUTPUT LEVEL REGISTER The parameters for the two BTSC processors are stored in two 256-location RAM spaces. The user should not change most of these parameters, although editing the dynamics processing curve for dialog enhancement may be useful if the curve needs to be changed for a specific application. This is explained in the Dialog Enhancement Register section of this data sheet. The output level register controls the overall BTSC output level. Its default value is –6 dB, which outputs a 600 mV rms reference level for a 1 kHz 0 dB mono digital input signal. This value is in 2.20 format, and –6 dB corresponds to binary 0010000000000000000000. This register is used in conjunction with the output filter to match the output BTSC level of the encoder with the decoder input to achieve maximum separation values. This level control should not be used to control the overall volume level of the audio signal. CONTROL REGISTER Control Register 1 is an 11-bit register that controls serial modes, de-emphasis, mute, power-down, and SPI-to-memory transfers. Table 12 documents the contents of this register. Bits 4:5 and 8:10 are reserved and should be set to 0 at all times. The audio signal is muted with Bit 7 of the control register. The soft power-down bit (Bit 6) stops the internal clocks to the DSP core, but does not reset the part. The digital power consumption is reduced to a low level when this bit is asserted. Reset can only be asserted using the external reset pin. Bits 3:2 select the serial format from one of four modes. These different formats are discussed in the Initialization section of this data sheet. The word length bits (1:0) are used in right-justified serial modes to determine where the MSB is located relative to the start of the audio frame. Table 12. Control Register Contents Register Bits 10 9 8 7 6 5:4 3:2 1:0 Function Reserved, Set to 0 Reserved, Set to 0 Reserved, Set to 0 Soft Mute (1 = Start Mute Sequence) Soft Power-Down (1 = Power-Down) Reserved, Set to 00 Serial In Mode 00 = I2S 01 = Right-Justified 10 = DSP 11 = Left-Justified Word Length 00 = 24 Bits 01 = 20 Bits 10 = 16 Bits 11 = 16 Bits STEREO ENHANCEMENT REGISTER This register controls ADI’s patented Phat Stereo spatial enhancement algorithm. The default is all 0s, which corresponds to no effect. The maximum setting is 0100000000000000000000, or a twos complement fractional value of 1.0. Note that the bass energy in each channel is increased using this algorithm, which may cause some digital clipping on full-scale signal peaks, especially at low frequencies. DIALOG ENHANCEMENT REGISTER This controls the built-in dialog-enhancement algorithm, and defaults to 0. The maximum setting is 0100000000000000000000, or a twos complement fractional value of 1.0. This algorithm is intended to solve the problem of playing back high dynamic range digital audio signals over a television’s built-in speakers. It provides an amplitude boost to signals that are in the range where dialog signals are usually found, while at the same time preventing loud special effects passages from overloading the speakers or amplifiers. The dialog enhancement control is set up as a dynamics processing curve with 33 locations on the curve, each spaced 3 dB apart. There is a default dialog enhancement curve that is set at power-up, but this can be changed if a different curve is desired. The curve ranges from an rms input level of –87 dB on the low end to +9 dB on the high end. The value corresponding to each point in the parameter RAM represents a gain at the appropriate input level. This gain value should range from 0 (–∞ dB) to +2.0 – 1 LSB (approximately +6 dB). The gain at a –87 dB input corresponds to parameter RAM location 4 on Processor A and location 516 on Processor B. The table extends to the +9 dB input gain at locations 36 and 548 for Processors A and B, respectively. Rev. 0 | Page 13 of 20 AD71028 Table 13. SPI Control Register 1 Write format Byte 0 00000, Wb/R, Adr [9:8] Byte 1 Adr [7:0] Byte 2 00000, Bit [10:8] Byte 3 Bit [7:0] Table 14. SPI Write Format for Parameter RAM, Output Level, Stereo Spreading and Dialog Enhancement Registers Byte 0 000000, Adr [9:8] Byte1 Adr [7:0] Byte 2 00, Level [21:16] Byte 3 Level [15:8] Byte 4 Level [7:0] SPI READ/WRITE DATA FORMATS Serial Data Input Modes The read/write formats of the SPI port are designed to be byteoriented. This allows for easy programming of common microcontroller chips. In order to fit into a byte-oriented format, 0s are appended to the data fields in order to extend the data-word to the next multiple of 8 bits. For example, 22-bit words written to the SPI parameter RAM are appended with two leading zeros in order to reach 24 bits (3 bytes). These zero-extended data fields are appended to a 2-byte field consisting of a read/write bit and a 10-bit address. The SPI port knows how many data bytes to expect based on the address that is received in the first 2 bytes. Figure 7 shows the left-justified mode. LRCLK is high for the left channel and low for the right channel. Data is sampled on the rising edge of BCLK. The MSB is left-justified to a LRCLK transition with no MSB delay. The left-justified mode can accept any word length up to 24 bits. INITIALIZATION Power-Up Sequence The AD71028 has a built-in power-up sequence that initializes the contents of all internal RAM. During this time, the SPI parameter RAM is filled with values from its associated boot ROM. The data memories are also cleared during this time. The boot sequence lasts for 1024 MCLK cycles and starts on the rising edge of the RESETB pin. The user should avoid writing to or reading from the SPI registers during this period of time. SERIAL DATA INPUT PORT The AD71028’s flexible serial data input port accepts data in twos complement, MSB-first format. The left channel data field always precedes the right channel data field. The serial mode is set by using mode select bits in the SPI control register. In all modes except the right-justified mode, the serial port will accept an arbitrary number of bits up to a limit of 24 (extra bits will not cause an error, but they will be truncated internally). In right-justified mode, SPI control register bits are used to set the word length to 16, 20, or 24 bits. The default on power-up is 24-bit mode. Proper operation of the right-justified mode requires that there be exactly 64 BCLKs per audio frame. Figure 8 shows the I2S mode, which is the default setting. LRCLK is low for the left channel, and the MSB is delayed from the edge of the LRCLK by a single BCLK period. The I2S mode can be used to accept any number of bits up to 24. Figure 9 shows the AD71028’s right-justified mode. LRCLK is high for the left channel and low for the right channel. Data is sampled on the rising edge of BCLK. The start of data is delayed from the LRCLK edge by 16, 12, or 8 BCLK intervals, depending on the selected word length. The default word length is 24 bits; other word lengths are set by writing to Bits <1:0> of the control register. In right-justified mode, it is assumed that there are 64 BCLKs per frame. Figure 10 shows the DSP serial port mode. LRCLK must pulse high for at least one bit clock period before the MSB of the left channel is valid, and LRCLK must pulse high again for at least one bit clock period before the MSB of the right channel is valid. Data is sampled on the falling edge of BCLK. The DSP serial port mode can be used with any word length up to 24 bits. In this mode, it is the responsibility of the DSP to ensure that the left data is transmitted with the first LRCLK pulse, and that synchronism is maintained from that point forward. Rev. 0 | Page 14 of 20 AD71028 MSB LSB MSB 04482-0-007 SDATA RIGHT CHANNEL LEFT CHANNEL LRCLK BCLK LSB 1 /FS Figure 7. Left-Justified Mode—16 Bits to 24 Bits per Channel LEFT CHANNEL LRCLK RIGHT CHANNEL SDATA LSB MSB 04482-0-008 BCLK LSB MSB 1 /FS Figure 8. I2S Mode—16 Bits to 24 Bits per Channel SDATA MSB LSB MSB LSB 1 /FS 04482-0-009 RIGHT CHANNEL LEFT CHANNEL LRCLK BCLK Figure 9. Right-Justified Mode—16 Bits to 24 Bits per Channel BCLK SDATA MSB MSB LSB 1 /FS Figure 10. DSP Mode—16 Bits to 24 Bits per Channel NOTES 1. DSP mode does not identify the channel. 2. LRCLK normally operates at FS; in DSP mode, LRCLK operates at 2 × FS. 3. BCLK frequency is normally 64 × LRCLK but may be operated in burst mode. Rev. 0 | Page 15 of 20 LSB 04482-0-010 LRCLK AD71028 ANALOG OUTPUT SECTION Figure 11 shows the block diagram of the analog output section (one of two channels). A series of current sources is controlled by a digital Σ-∆ modulator. Depending on the digital code from the modulator, each current source is connected to the summing junction of either a positive I-to-V converter or a negative I-to-V converter. Two extra current sources that push instead of pull are added to set the midscale common-mode voltage. All current sources are derived from the VREF input pin. The gain of the AD71028 is directly proportional to the magnitude of the current sources, and therefore the gain of the AD71028 is proportional to the voltage on the VREF pin. The nominal VREF voltage should be set to 2.5 V, using a simple resistive divider from the analog supply. The VREF and biasing circuits are common to both DACs. IREF OUT+ The outputs can also be used single-ended, with some loss of performance; the DAC distortion may become significantly poorer, although the SNR will remain quite high. OUT– VREF IN IREF + DIG_IN For best performance, a large (>10 µF) capacitor should be connected between the FILTCAP pin and analog ground. IREF – DIG_IN SWITCHED CURRENT SOURCES 04482-0-011 BIAS FROM DIGITAL Σ–∆ MODULATOR (DIG_IN) The AD71028 should be used with an external third-order filter on each output channel. The circuit shown in Figure 12 combines a third-order filter and a single-ended-to-differential converter in the same circuit. The values shown are for a 100 kHz Bessel filter. The use of a Bessel filter is important to maintain the time alignment of the pilot to the carrier. If these signals are not in phase, a loss of separation will occur. 2.80kΩ –INPUT 3.01kΩ 270pF 1.50kΩ 1nF 549Ω OUT Figure 11. Internal DAC Analog Architecture 2.7nF +INPUT 2.2nF 499kΩ 806Ω 1.00kΩ 820pF Figure 12. Recommended External Analog Filter for Each Channel Rev. 0 | Page 16 of 20 04482-0-012 IREF Since the VREF input effectively multiplies the signal, care must be taken to ensure that no ac signals appear on this pin. This can be accomplished by using a large decoupling capacitor in the VREF external resistive divider circuit. If the VREF signal is derived by dividing the 5 V analog supply, the time constant of the divider must effectively filter any noise on the supply. If the VREF signal is derived from an unregulated power amplifier supply, the time constant must be longer because the ripple on the amplifier supply voltage will presumably be greater than in the case of the 5 V supply. AD71028 OUTLINE DIMENSIONS 0.75 0.60 0.45 9.00 BSC SQ 1.60 MAX 37 48 36 1 1.45 1.40 1.35 0.15 0.05 10° 6° 2° SEATING PLANE PIN 1 SEATING PLANE 7.00 BSC SQ TOP VIEW 0.20 0.09 (PINS DOWN) VIEW A 7° 3.5 ° 0° 0.08 MAX COPLANARITY 25 12 13 0.50 BSC VIEW A 24 0.27 0.22 0.17 ROTATED 90° CCW COMPLIANT TO JEDEC STANDARDS MS-026BBC Figure 13. 48-Lead Low Profile Quad Flatpack [LQFP] (ST-48) Dimensions Shown in Millimeters ORDERING GUIDE Model AD71028JST AD71028JSTRL Temperature Range –0°C to +70°C –0°C to +70°C Package Description 48-Lead LQFP 48-Lead LQFP Rev. 0 | Page 17 of 20 Package Option ST-48 ST-48 on 13” Reel AD71028 NOTES Rev. 0 | Page 18 of 20 AD71028 NOTES Rev. 0 | Page 19 of 20 AD71028 NOTES © 2004 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D04482–0–1/04(0) Rev. 0 | Page 20 of 20