3.0x2.5mm SURFACE MOUNT LED LAMP Part Number: APB3025SYKQWDF ATTENTION Super Bright Yellow White OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions z 3.0mmx2.5mm SMD LED, 1.1mm thickness. z The Super Bright Yellow device is made with AlGaInP z Bi -color,low power consumption. (on GaAs substrate) light emitting diode chip. z The source color devices are made with InGaN Light z Wide viewing angle. z Ideal for backlight and indicator. Emitting Diode. z Electrostatic discharge and power surge could damage z Package : 2000pcs / reel. z Moisture sensitivity level : level 3. the LEDs. z It is recommended to use a wrist band or anti- z RoHS compliant. electrostatic glove when handling the LEDs. z All devices, equipments and machineries must be electrically grounded. Package Dimensions Yellow White Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.2(0.008") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAL1002 REV NO: V.3B DATE: OCT/14/2015 PAGE: 1 OF 7 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203011785 Selection Guide Part No. Emitting Color (Material) Super Bright Yellow (AlGaInP) APB3025SYKQWDF Viewing Angle [1] Iv (mcd) [2] @ 20mA Lens Type Min. Typ. 80 150 200 380 Yellow Fluorescent White (InGaN) 2θ1/2 120° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous Flux: +/-15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C [YELLOW] Symbol Parameter Emitting Color Typ. λpeak Peak Wavelength Super Bright Yellow λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 590 nm IF=20mA Super Bright Yellow 590 nm IF=20mA Spectral Line Half-width Super Bright Yellow 20 nm IF=20mA C Capacitance Super Bright Yellow 20 pF VF=0V;f=1MHz VF [2] Forward Voltage Super Bright Yellow 2 2.5 V IF=20mA IR Reverse Current Super Bright Yellow 10 uA VR = 5V Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Electrical / Optical Characteristics at TA=25°C Symbol Parameter VF [1] Forward Voltage White IR Reverse Current White Chromaticity Coordinates White [WHITE] Emitting Color X [2] Typ. Max. Units Test Conditions 3.3 4.0 V IF=20mA 50 uA VR = 5V pF VF=0V;f=1MHz 0.31 Y [2] C 0.31 Capacitance White 100 Notes: 1. Forward Voltage: +/-0.1V. 2. Measurement tolerance of the chromaticity coordinates is ±0.01. 3. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Super Bright Yellow White Units Power dissipation 75 120 mW DC Forward Current 30 30 mA Peak Forward Current [1] 175 150 mA Electrostatic Discharge Threshold (HBM) 3000 250 V Reverse Voltage 5 Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C V Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAL1002 REV NO: V.3B DATE: OCT/14/2015 PAGE: 2 OF 7 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203011785 APB3025SYKQWDF Super Bright Yellow SPEC NO: DSAL1002 REV NO: V.3B DATE: OCT/14/2015 PAGE: 3 OF 7 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203011785 White SPEC NO: DSAL1002 REV NO: V.3B DATE: OCT/14/2015 PAGE: 4 OF 7 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203011785 APB3025SYKQWDF White CIE 0.40 c0 0.35 y b1 0.30 b2 a0 0.25 a2 0.20 0.20 0.25 0.30 0.35 0.40 x a2 b1 x y x y x y 0.263 0.213 0.282 0.245 0.298 0.271 0.282 0.245 0.298 0.271 0.313 0.296 0.265 0.265 0.286 0.299 0.306 0.332 0.242 0.226 0.265 0.265 0.286 0.299 0.313 0.296 0.329 0.325 0.329 0.325 0.358 0.372 0.329 0.371 0.363 0.400 0.306 0.332 0.329 0.371 a0 c0 b2 Notes: Shipment may contain more than one chromaticity regions. Orders for single chromaticity region are generally not accepted. Measurement tolerance of the chromaticity coordinates is ±0.01. SPEC NO: DSAL1002 REV NO: V.3B DATE: OCT/14/2015 PAGE: 5 OF 7 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203011785 APB3025SYKQWDF Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAL1002 REV NO: V.3B DATE: OCT/14/2015 PAGE: 6 OF 7 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203011785 PACKING & LABEL SPECIFICATIONS APB3025SYKQWDF Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAL1002 REV NO: V.3B DATE: OCT/14/2015 PAGE: 7 OF 7 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203011785