L9820 ® HIGH SIDE DRIVER OPERATING SUPPLY VOLTAGE UP TO 25V DC CURRENT 0.3A RON < 800mΩ DIAGNOSTIC AND PROTECTION FUNCTIONS µP COMPATIBLE ENABLE INPUT FOR STAND-BY MODE DESCRIPTION The L9820 High Side Driver realized with Multipower - BCD mixed technology, drives resistive or inductive loads with one side connected to ground. The ENABLE input is TTL compatible and a diagnostic output provides an indication of short circuit and device status (thermal and overvoltage shutdown). Onchip thermal protection and short circuit protection are provided. MULTIPOWER BCD TECHNOLOGY Minidip SO8 ORDERING NUMBERS: L9820 L9820D BLOCK DIAGRAM 40mΩ September 2013 1/6 L9820 ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit 50 Vdc Reverse Bias Current at -1.3V Input Voltage (to GND) –0.46 –0.3 to 20 A V Diag. Output Voltage (to GND) Output Voltage (to GND) –0.3 to 20 –0.3 to 25 V V VS Max Forward Voltage IR V5 V8 V1 I4 I5 Supply Current Enable Input Current 0.5 mA I8 I1 Diag. Out Current (sink) 10 mA Output Current Operation Temperature Internally limited –40 to 85 °C –55 to 150 °C 150 °C Top Tj, Tstg Internally limited Junction and Storage Temperature Range Detecting Temperature Tjp PIN CONNECTION (Top views) Minidip SO8 THERMAL DATA Symbol Parameter Rth j-amb Thermal Resistance Junction-ambient Max. Minidip SO8 Unit 100 200 °C/W TRUTH TABLE H: high level L: low level 2/6 ENABLE FUNCTION DIAG. STATUS POWER STATUS L H H Operating OFF Normal Operation Overvoltage Protection ON H H L L H L H H Overcurrent Protection ON Overtemperature Protection ON L L L L L9820 PIN FUNCTIONS N. Name 1 POWER OUTPUT 4 POWER SUPPLY 5 ENABLE INPUT 7 GROUND 8 DIAGNOSTIC FEEDBACK Description The device is provided with short circuit protection. Supply voltage input. TTL compatible input. High level on this pin means output current ON. The low level voltage switches off the charge pump, the power stage and the diagnostic output reducing to the minimum value the quiescent current. This pin must be connected to ground. The diagnostic circuit is active in input high level condition. This output detects with Tipically 50µs delay at Tamb = 25°C the following faults: – Overvoltage condition. – Thermal shutdown. – Short circuit. The power stage current is internally limited at 1.5A. The diagnostic output is active low. The diagnostic delay time allows to avoid spurious diagnosys(i.e.: turn ON overcurrent, overvoltage spikes etc.). ELECTRICAL CHARACTERISTICS (VS = 14.4V, –40°C≤ Tj ≤ +85°C, unless otherwise specified.) Symbol Parameter VS Ron Operating Supply Voltage On Resistance Ioff Off State Supply Current Ion VEL On State Supply Current VEH IE Ileakd Vsatd Enable High Level Enable Current Diagnostic Output Leakage Current Test Condition Min. Typ. Max. Unit 0.6 25 0.8 1.2 V Ω Ω 130 300 4 µA µA mA 6 Input > 2V, Tj = 25°C Input > 2V, Full T range Tj < 35°C Tj = 85°C Enable Low Level 0.8 V 0V < Vi <5V VCC = 5V Diagnostic Output High 10 10 V µA µA Diagnostic Output Saturated Voltage Isink < 3.5mA 0.4 V tdd tdon tr Diagnostic Delay Time Output ON Delay Time Tj = 25°C Tj = 25°C 30 30 µs µs Output ON Rise Time Tj = 25°C 100 µs tdoff tf Vdon Output OFF Delay Time Output OFF Fall Time Overvoltage Detection ON Tj = 25°C Tj = 25°C 80 100 µs µs V Vdh Idon Tdon Tdh Overvoltage Hysteresis Overcurrent Detection ON Overtemperature Detection ON Overtemperature Hysteresis 2 25 2 0.5 150 5 1.5 25 50 V A °C °C 3/6 L9820 mm DIM. MIN. TYP. A a1 inch MAX. MIN. TYP. 1.75 0.1 0.25 a2 MAX. 0.069 0.004 0.010 1.65 0.065 a3 0.65 0.85 0.026 0.033 b 0.35 0.48 0.014 0.019 b1 0.19 0.25 0.007 0.010 C 0.25 0.5 0.010 0.020 c1 45° (typ.) D (1) 4.8 5.0 0.189 0.197 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 3.81 0.150 F (1) 3.8 4.0 0.15 0.157 L 0.4 1.27 0.016 0.050 M S 0.6 0.024 8 ° (max.) (1) D and F do not include mold flash or protrusions. Mold flash or potrusions shall not exceed 0.15mm (.006inch). 4/6 OUTLINE AND MECHANICAL DATA SO8 L9820 mm inch DIM. MIN. A TYP. MAX. MIN. 3.32 TYP. MAX. 0.131 a1 0.51 B 1.15 1.65 0.045 0.065 b 0.356 0.55 0.014 0.022 b1 0.204 0.304 0.008 0.012 0.020 D E 10.92 7.95 9.75 0.430 0.313 0.384 e 2.54 0.100 e3 7.62 0.300 e4 7.62 0.300 F 6.6 0.260 I 5.08 0.200 L Z 3.18 OUTLINE AND MECHANICAL DATA 3.81 1.52 0.125 0.150 Minidip 0.060 5/6 L9820 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2013 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 6/6 DocID4283 Rev 3